Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 31 - 60 of 174

Full-Text Articles in Engineering

Insar Simulations For Swot And Dual Frequency Processing For Topographic Measurements, Gerard Masalias Huguet Mar 2019

Insar Simulations For Swot And Dual Frequency Processing For Topographic Measurements, Gerard Masalias Huguet

Masters Theses

In Earth remote sensing precise characterization of the backscatter coefficient is important to extract valuable information about the observed target. A system that eliminates platform motion during near-nadir airborne observations is presented in this thesis, showing an improvement on the accuracy of measurements for a Ka- band scatterometer previously developed at Microwave Remote Sensing Laboratory (MIRSL). These very same results are used to simulate the reflectivity of such targets as seen from a spaceborne radar and estimate height errors based on mission-specific geometry. Finally, data collected from a dual-frequency airborne interferometer com- prised by the Ka-band system and an S-band …


Controlled Switching In Kalman Filtering And Iterative Learning Controls, He Li Jan 2019

Controlled Switching In Kalman Filtering And Iterative Learning Controls, He Li

Masters Theses

“Switching is not an uncommon phenomenon in practical systems and processes, for examples, power switches opening and closing, transmissions lifting from low gear to high gear, and air planes crossing different layers in air. Switching can be a disaster to a system since frequent switching between two asymptotically stable subsystems may result in unstable dynamics. On the contrary, switching can be a benefit to a system since controlled switching is sometimes imposed by the designers to achieve desired performance. This encourages the study of system dynamics and performance when undesired switching occurs or controlled switching is imposed. In this research, …


Evaluation Of Naturally Occurring And Anthropogenic Contamination In Missouri Streams, Christina Jane Sehrt Jan 2019

Evaluation Of Naturally Occurring And Anthropogenic Contamination In Missouri Streams, Christina Jane Sehrt

Masters Theses

"The goal of this study is to observe the values and variability of water quality parameters and benthic macroinvertebrates in watersheds with very little anthropogenic impact and to compare these values with those acquired in watersheds with more anthropogenic impact. The following five HUC 12-digit watersheds had very little anthropogenic impact and were considered "pristine": Rogers Creek, Mill Creek, Middle West Fork-Black River, Bee Fork, and Ottery Creek. Five largely urban sub-basins were also considered; these basins are: Grand Glaize Creek, Glaize Creek, Sugar Creek, Hominy Creek, and Grindstone Creek. For each watershed, both water quality parameters and benthic macroinvertebrates …


Removal Of Antimony And Bismuth From Copper Electrorefining Electrolyte By Two Proprietary Solvent Extraction Extractants, Andrew Artzer Jan 2019

Removal Of Antimony And Bismuth From Copper Electrorefining Electrolyte By Two Proprietary Solvent Extraction Extractants, Andrew Artzer

Masters Theses

"Antimony and bismuth are two of the most problematic impurities in copper electrorefining (ER). Because of this, much research has been done investigating the ways to remove them. Processes that are currently being used industrially include anode additions, liberators, ion exchange (IX), and solvent extraction (SX). Of these, liberators and anode additions are the most common while SX is the least, mostly being used for arsenic removal. There are other methods that have been evaluated, but are not in commercial use. These include the use of various electrolyte additives, and adsorbents such as bentonite clay and heavy metal sulfates.

Two …


Temporal Changes Of Nutrients Within The Lower Grand River Watershed And Selected Sites, Weston Scott Duley Jan 2019

Temporal Changes Of Nutrients Within The Lower Grand River Watershed And Selected Sites, Weston Scott Duley

Masters Theses

"This report presents the results of a study carried out in collaboration with the U.S. Geological Survey (USGS) and the Missouri Department of Natural Resources (MDNR) to estimate total nitrogen (TN) and total phosphorus (TP) at five USGS monitoring sites within Lower Grand River Watershed (LGRW) and two monitoring sites on the Missouri River. The objective of this study was to quantify temporal changes in TN and TP concentrations and compare those to best management practices (BMPs).

In this study, the approach to the analysis of long-term surface water-quality data by using Weighted Regressions on Time, Discharge and Seasons models …


Geophysical Imaging Beneath Lake Chesterfield, Missouri, James Daniell Hayes Jan 2019

Geophysical Imaging Beneath Lake Chesterfield, Missouri, James Daniell Hayes

Masters Theses

"Lake Chesterfield in Wildwood, Missouri, has been leaking since construction of the earth-fill dam was completed in 1986, despite numerous mitigation efforts. The mitigation efforts, including the injection of grouting and the emplacement of clay liners, has not solve the leakage problem.

In the current study, geophysical (subsurface imaging) data was acquired across the drained and dry lake bed and along the base of the earth-fill dam to 1) map variable depth to top of bedrock, 2) determine the variable quality of the bedrock to depths on the order of 80 ft., 3) identify any significant karst features beneath the …


Less Is More: Beating The Market With Recurrent Reinforcement Learning, Louis Kurt Bernhard Steinmeister Jan 2019

Less Is More: Beating The Market With Recurrent Reinforcement Learning, Louis Kurt Bernhard Steinmeister

Masters Theses

"Multiple recurrent reinforcement learners were implemented to make trading decisions based on real and freely available macro-economic data. The learning algorithm and different reinforcement functions (the Differential Sharpe Ratio, Differential Downside Deviation Ratio and Returns) were revised and the performances were compared while transaction costs were taken into account. (This is important for practical implementations even though many publications ignore this consideration.) It was assumed that the traders make long-short decisions in the S&P500 with complementary 3-month treasury bill investments. Leveraged positions in the S&P500 were disallowed. Notably, the Differential Sharpe Ratio and the Differential Downside Deviation Ratio are risk …


Application And Evaluation Of Lighthouse Technology For Precision Motion Capture, Soumitra Sitole Oct 2018

Application And Evaluation Of Lighthouse Technology For Precision Motion Capture, Soumitra Sitole

Masters Theses

This thesis presents the development towards a system that can capture and quantify motion for applications in biomechanical and medical fields demanding precision motion tracking using the lighthouse technology. Commercially known as SteamVR tracking, the lighthouse technology is a motion tracking system developed for virtual reality applications that makes use of patterned infrared light sources to highlight trackers (objects embedded with photodiodes) to obtain their pose or spatial position and orientation. Current motion capture systems such as the camera-based motion capture are expensive and not readily available outside of research labs. This thesis provides a case for low-cost motion capture …


A Study On Modelling Spatial-Temporal Human Mobility Patterns For Improving Personalized Weather Warning, Yue Xu Jul 2018

A Study On Modelling Spatial-Temporal Human Mobility Patterns For Improving Personalized Weather Warning, Yue Xu

Masters Theses

Understanding human mobility patterns is important for severe weather warning since these patterns can help identify where people are in time and in space when flash floods, tornados, high winds and hurricanes are occurring or are predicted to occur. A GIS (Geographic Information Science) data model was proposed to describe the spatial-temporal human activity. Based on this model, a metric was designed to represent the spatial-temporal activity intensity of human mobility, and an index was generated to quantitatively describe the change in human activities. By analyzing high-resolution human mobility data, the paper verified that human daily mobility patterns could be …


Streamwise Flow-Induced Oscillations Of Bluff Bodies - The Influence Of Symmetry Breaking, Tyler Gurian Jul 2018

Streamwise Flow-Induced Oscillations Of Bluff Bodies - The Influence Of Symmetry Breaking, Tyler Gurian

Masters Theses

The influence of symmetry breaking on the flow induced oscillations of bluff bodies in the steamwise direction is studied. First, a series of experiments is conducted on a one-degree-of-freedom circular cylinder allowed to exhibit pure translational motion in the streamwise direction over a range of reduced velocities, 1.4 < U* < 4.4, corresponding to a Reynolds number range of 970 < Re < 3370. Two distinct regions of displacements were observed in reduced velocity ranges of 1.6 < U* < 2.5 and 2.75 < U* < 3.85. Measured force coefficients in the drag and lift direction were examined, along with the wake visualization, through the range of reduced velocities, to infer the resulting wake modes. A new Alternating Symmetric (AS) mode was found. This transition from symmetric to AS shedding occurred near the end of the first region of response. Similar tests were run with a square prism in the parameter space of 2.4 < U* < 5.8 and 757 < Re < 1900 over angles of incidence of 0° ≤ α ≤ 45°. A distinct region of lock-in is observed for α = 0°, 2.5°, 5°, 7.5° over 3.2 < U* < 5.4 for α = 0°, and decreasing with increasing α. The wake structures were found to be roughly symmetric for α = 0°, but transitioned towards asymmetry …


Processing Different Mixtures Of Regionally Available Resources To Create Pellets That Meet A Minimum Standard, Jacob Hixson Jan 2018

Processing Different Mixtures Of Regionally Available Resources To Create Pellets That Meet A Minimum Standard, Jacob Hixson

Masters Theses

There are several ways to produce energy today, one of the oldest is the gasification of biomass. This process uses a fire to heat the material until it starts to produce gasses that are used as fuel. There are several types of biomass that can be used, many of which have large pieces with low bulk densities. By pelletizing the biomass bulk density increases and allows the opportunity to add in other biomass materials.

There are standards for condensing large pieces of biomass to smaller pelletized materials. Pellet Fuels Institute has set minimum standards for pellets used in the different …


Smart Augmented Reality Instructional System For Mechanical Assembly, Ze-Hao Lai Jan 2018

Smart Augmented Reality Instructional System For Mechanical Assembly, Ze-Hao Lai

Masters Theses

"Quality and efficiency are pivotal indicators of a manufacturing company. Many companies are suffering from shortage of experienced workers across the production line to perform complex assembly tasks such as assembly of an aircraft engine. This could lead to a significant financial loss. In order to further reduce time and error in an assembly, a smart system consisting of multi-modal Augmented Reality (AR) instructions with the support of a deep learning network for tool detection is introduced. The multi-modal smart AR is designed to provide on-site information including various visual renderings with a fine-tuned Region-based Convolutional Neural Network, which is …


Modulated Photothermal Radiometry: Detector Sensitivity Study And Experimental Setup, Jessica Nicole Seals Jan 2018

Modulated Photothermal Radiometry: Detector Sensitivity Study And Experimental Setup, Jessica Nicole Seals

Masters Theses

"This thesis outlines the development of a system used for determining the surface thermal diffusivity of both non-irradiated and irradiated materials. The motivation for this work is to establish a modulated photothermal radiometry (PTR) system on the campus of Missouri University of Science and Technology. One of the main efforts described in this thesis is the design and construction of the physical apparatus. Along the way, it was necessary to perform a detailed sensitivity analysis of the system to determine whether the expected signal emitted from the sample falls within the bounds of detectivity for the HgCdTe (MCT) detector used …


Customized Multi-Group Cross Section Generation With Njoy For Discrete Ordinates Computed Tomography And Radiography Simulation, Steven Michael Wagstaff Jan 2018

Customized Multi-Group Cross Section Generation With Njoy For Discrete Ordinates Computed Tomography And Radiography Simulation, Steven Michael Wagstaff

Masters Theses

"The purpose of this work was to explore the creation of photoatomic multi-group cross section libraries to be used with a software package DOCTORS (Discrete Ordinates Computed TOmography and Radiography Simulator). This software solves the linear Boltzmann equation using the discrete ordinates method [1]. To create these libraries, NJOY2016 was used, creating both fine and broad energy multi-group cross section files. The cross section's accuracy was tested against an equivalent Monte Carlo simulation using MCNP6.

Two simulation geometries were used. The first, a cylindrical water phantom with a single source projection placed in front, simulating an X-ray radiography. The second …


Bridge Deck Assessment Using Visual Inspection, Ground Penetrating Radar, Portable Seismic Property Analyzer-Ultrasonic Surface Wave, Hammer Sounding And Chain Drag, Abdullah Hadi Zaid Alhaj Jan 2018

Bridge Deck Assessment Using Visual Inspection, Ground Penetrating Radar, Portable Seismic Property Analyzer-Ultrasonic Surface Wave, Hammer Sounding And Chain Drag, Abdullah Hadi Zaid Alhaj

Masters Theses

"Integrated non-destructive techniques were utilized to assess the condition of a reinforced concrete bridge deck. There were two main objectives accomplished.

The first objective was to assess the integrity of the reinforced concrete bridge deck using four non-destructive techniques, namely visual inspection, ground penetrating radar, portable seismic property analyzer-ultrasonic surface wave, and hammer sounding and chain drag. Visual inspection data were used to identify signs of deterioration on surface of the bridge deck such as cracking, concrete leaching, and reinforcement corrosion. Ground penetrating radar data were used to determine the relative condition of the bridge deck. However, due to the …


Developing Computational Models For Pulsed-Inductive Plasma Formation, Zachary Aaron Gill Jan 2018

Developing Computational Models For Pulsed-Inductive Plasma Formation, Zachary Aaron Gill

Masters Theses

"Pulsed-inductive discharges are a common method of producing a plasma. They provide a mechanism for quickly and efficiently generating a large volume of plasma for rapid use and are seen in applications including propulsion, fusion power, and high-power lasers. However, some common designs see a delayed response time due to the plasma forming when the magnitude of the magnetic field in the device is at a minimum. New designs are difficult to evaluate due to the amount of time needed to construct a new geometry and the high monetary cost of changing the power generation circuit. To more quickly evaluate …


Imaging The Subsurface In Eastern Part Of Lake Chesterfield Using A Combination Of Geophysical Tools, Jiawei Li Jan 2018

Imaging The Subsurface In Eastern Part Of Lake Chesterfield Using A Combination Of Geophysical Tools, Jiawei Li

Masters Theses

"The Lake Chesterfield North Dam in Wildwood city, Missouri has been leaking, more or less continuously since the dam was constructed in 1986 despite mitigation efforts in 1988, 1994, 1995, 2004, and 2005. Neither the grouting efforts in 1988, 1994, 1995, 2004 or 2005, nor the placement and rehabilitation of an impervious clay liner in 2005 has solved the problem. Indeed, in June of 2017, the water level in Lake Chesterfield dropped at an alarmingly rapid rate.

Prior to authorizing additional mitigation work, the Lake Chesterfield Home Owners Association (LCHOA) decided to acquire geophysical data across the dry lake bed. …


Research And Development Of Optically Transparent Join With Low Processing Temperatures, Eric Kevin Muskovin Jan 2018

Research And Development Of Optically Transparent Join With Low Processing Temperatures, Eric Kevin Muskovin

Masters Theses

The purpose of this study was to investigate durable solar cell cover glass joins produced by diffusion bonding with deep eutectic solvents (DES) and to develop a novel process of joining optically transparent materials at low temperatures. A joined PV cell-glass specimen was characterized using Raman, μ-FTIR, SEM-EDS, and thin-film XRD. DESs were created with malonic acid (MAL) and choline chloride (ChCl) of varying composition factors (CF; CF=MAL/ChCl). Joining borosilicate glass coupons was attempted using DESs with CF = 0.65 and 1 at temperatures between 100-150 °C for 20 hours. Joining the glass coupons failed at all temperatures and oxygen …


Conical Folds -- An Artifact Of Using Simple Geometric Shapes To Describe A Complex Geologic Structure, Avery Joseph Welker Jan 2018

Conical Folds -- An Artifact Of Using Simple Geometric Shapes To Describe A Complex Geologic Structure, Avery Joseph Welker

Masters Theses

"Accurate representation of the 3D shapes of natural folds is essential to characterization of the dynamic models for fold formation. Geometrical analysis of folds commonly relies upon analyzing patterns defined by the variation in the orientation of poles to planar surfaces deformed by a shortening event when plotted using graphical calculators (e.g., stereogram, polar tangent diagrams) to interpret the shape of folds. Stereograms for which orientation data define small circles are classified as non-cylindrical regular folds and are interpreted as "conical folds," where the shape of the fold is represented by a cone that terminates at a point. Utilizing similar …


Numerical Modeling Of Capillary-Driven Flow In Open Microchannels: An Implication Of Optimized Wicking Fabric Design, Mehrad Gholizadeh Ansari Jan 2018

Numerical Modeling Of Capillary-Driven Flow In Open Microchannels: An Implication Of Optimized Wicking Fabric Design, Mehrad Gholizadeh Ansari

Masters Theses

"The use of microfluidics to transfer fluids without applying any exterior energy source is a promising technology in different fields of science and engineering due to their compactness, simplicity and cost-effective design. In geotechnical engineering, to increase the soil's strength, hydrophilic wicking fibers as type of microfluidics have been employed to transport and drain water out of soil spontaneously by taking advantage of natural capillary force without using any pumps or other auxiliary devices. The objective of this study is to understand the scientific mechanisms of the capability for wicking fiber to drain both gravity and capillary water out of …


Evaluating Microgrid Effectiveness In Transitioning Energy Portfolios, Jacob Marshal Hale Jan 2018

Evaluating Microgrid Effectiveness In Transitioning Energy Portfolios, Jacob Marshal Hale

Masters Theses

"Microgrid energy systems have emerged as a potential solution to rising greenhouse gas emissions from dependence on fossil fuels. This research provides a framework for evaluating the utility of microgrids. Three key findings are presented: use of a state-of-the-art matrix (SAM) analysis to identify gaps in key research areas that inhibit wide-spread microgrid adoption, development of a system dynamics (SD) model, and a cost benefit analysis case study to evaluate microgrid feasibility in partially meeting the energy demand of a building. Governments play a central role in developing clean energy strategies. A SAM was developed to determine if key microgrid …


Analyzing Sensor Based Human Activity Data Using Time Series Segmentation To Determine Sleep Duration, Yogesh Deepak Lad Jan 2018

Analyzing Sensor Based Human Activity Data Using Time Series Segmentation To Determine Sleep Duration, Yogesh Deepak Lad

Masters Theses

"Sleep is the most important thing to rest our brain and body. A lack of sleep has adverse effects on overall personal health and may lead to a variety of health disorders. According to Data from the Center for disease control and prevention in the United States of America, there is a formidable increase in the number of people suffering from sleep disorders like insomnia, sleep apnea, hypersomnia and many more. Sleep disorders can be avoided by assessing an individual's activity over a period of time to determine the sleep pattern and duration. The sleep pattern and duration can be …


Precise Energy Efficient Scheduling Of Mixed-Criticality Tasks & Sustainable Mixed-Criticality Scheduling, Sai Sruti Jan 2018

Precise Energy Efficient Scheduling Of Mixed-Criticality Tasks & Sustainable Mixed-Criticality Scheduling, Sai Sruti

Masters Theses

"In this thesis, the imprecise mixed-criticality model (IMC) is extended to precise scheduling of tasks, and integrated with the dynamic voltage and frequency scaling (DVFS) technique to enable energy minimization. The challenge in precise scheduling of MC systems is to simultaneously guarantee the timing correctness for all tasks, hi and lo, under both pessimistic and optimistic (less pessimistic) assumptions. To the best of knowledge this is the first work to address the integration of DVFS energy conserving techniques with precise scheduling of lo-tasks of the MC model.

In this thesis, the utilization based schedulability tests and sufficient conditions for such …


Multiscale Approaches Toward Advanced Lithium-Ion Battery: From Nano To Meso Scale, Susmita Sarkar Jan 2018

Multiscale Approaches Toward Advanced Lithium-Ion Battery: From Nano To Meso Scale, Susmita Sarkar

Masters Theses

“Battery performance and its degradation are determined by various aspects such as the transport of ions and electrons through heterogeneous internal structures composed of constituent particles, kinetic reactions at the interfaces, and a corresponding interplay between mechanical, chemical, and thermal responses. Further, modern battery materials require a variety of engineering processes such as coating, doping and mixing. As a result, in order to fully understand the behavior of the battery material and improve battery performance, it is necessary to understand and control the individual particle behavior and then connect it to the electrode. This study elucidated the physical phenomena associated …


Developing Leading And Lagging Indicators To Enhance Equipment Reliability In A Lean System, Dhanush Agara Mallesh Dec 2017

Developing Leading And Lagging Indicators To Enhance Equipment Reliability In A Lean System, Dhanush Agara Mallesh

Masters Theses

With increasing complexity in equipment, the failure rates are becoming a critical metric due to the unplanned maintenance in a production environment. Unplanned maintenance in manufacturing process is created issues with downtimes and decreasing the reliability of equipment. Failures in equipment have resulted in the loss of revenue to organizations encouraging maintenance practitioners to analyze ways to change unplanned to planned maintenance. Efficient failure prediction models are being developed to learn about the failures in advance. With this information, failures predicted can reduce the downtimes in the system and improve the throughput.

The goal of this thesis is to predict …


Automated Program Profiling And Analysis For Managing Heterogeneous Memory Systems, Adam Palmer Howard Dec 2017

Automated Program Profiling And Analysis For Managing Heterogeneous Memory Systems, Adam Palmer Howard

Masters Theses

Many promising memory technologies, such as non-volatile, storage-class memories and high-bandwidth, on-chip RAMs, are beginning to emerge. Since each of these new technologies present tradeoffs distinct from conventional DRAMs, next-generation systems are likely to include multiple tiers of memory storage, each with their own type of devices. To efficiently utilize the available hardware, such systems will need to alter their data management strategies to consider the performance and capabilities provided by each tier.

This work explores a variety of cross-layer strategies for managing application data in heterogeneous memory systems. We propose different program profiling-based techniques to automatically partition program allocation …


Non-Equispaced Fast Fourier Transforms In Turbulence Simulation, Aditya M. Kulkarni Oct 2017

Non-Equispaced Fast Fourier Transforms In Turbulence Simulation, Aditya M. Kulkarni

Masters Theses

Fourier pseudo-spectral method on equispaced grid is one of the approaches in turbulence simulation, to compute derivative of discrete data, using fast Fourier Transform (FFT) and gives low dispersion and dissipation errors. In many turbulent flows the dynamically important scales of motion are concentrated in certain regions which requires a coarser grid for higher accuracy. A coarser grid in other regions minimizes the memory requirement. This requires the use of Non-equispaced Fast Fourier Transform (NFFT) to compute the Fourier transform, by solving a system of linear equations.

To achieve similar accuracy, the NFFT needs to return more Fourier coefficients than …


Development Of Nuclear Underground Engineered Test Surrogates For Technical Nuclear Forensics Exploitation, Robert Boone Gilbreath May 2017

Development Of Nuclear Underground Engineered Test Surrogates For Technical Nuclear Forensics Exploitation, Robert Boone Gilbreath

Masters Theses

A method for formulation and production of Nuclear UnderGround Engineered Test Surrogates (NUGETS) based on notional improvised nuclear device (IND) detonations in an underground environment analogous to the Nevada National Security Site (NNSS) is presented. Extensive statistical analyses of precursory geochemical and geophysical characteristics are combined with an augmented surrogate debris cooling technique and predictive IND contributions from the ORIGEN Fallout Analysis Tool. Precursory and resultant elemental compositions, cooling curve calculations, and visual comparison of NUGETS to genuine underground debris are reported. Application of NUGETS methodology to future studies in urban, underground post-detonation technical nuclear forensic (TNF) analysis is suggested.


Explorations Into Machine Learning Techniques For Precipitation Nowcasting, Aditya Nagarajan Mar 2017

Explorations Into Machine Learning Techniques For Precipitation Nowcasting, Aditya Nagarajan

Masters Theses

Recent advances in cloud-based big-data technologies now makes data driven solutions feasible for increasing numbers of scientific computing applications. One such data driven solution approach is machine learning where patterns in large data sets are brought to the surface by finding complex mathematical relationships within the data. Nowcasting or short-term prediction of rainfall in a given region is an important problem in meteorology. In this thesis we explore the nowcasting problem through a data driven approach by formulating it as a machine learning problem.

State-of-the-art nowcasting systems today are based on numerical models which describe the physical processes leading to …


Achieving Perfect Location Privacy In Wireless Devices Using Anonymization, Zarrin Montazeri Mar 2017

Achieving Perfect Location Privacy In Wireless Devices Using Anonymization, Zarrin Montazeri

Masters Theses

The popularity of mobile devices and location-based services (LBS) have created great concerns regarding the location privacy of the users of such devices and services. Anonymization is a common technique that is often being used to protect the location privacy of LBS users. This technique assigns a random pseudonym to each user and these pseudonyms can change over time. Here, we provide a general information theoretic definition for perfect location privacy and prove that perfect location privacy is achievable for mobile devices when using the anonymization technique appropriately. First, we assume that the user’s current location is independent from her …