Engineering Commons^™

Evaluation Of Deformable Posts In The Zoi And Rigid Posts In Stiff Soil, Thomas Ammon

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Debris fences are commonly used by states, in conjunction with a concrete parapet, to protect railway tracks. Their use limits the intrusion of debris that could damage tracks or clutter rail lines. Due to a lack of previously crash-tested systems, the safety performance of such designs are largely unknown. The Iowa Department of Transportation (DOT) desired that researchers at the Midwest Roadside Safety Facility (MwRSF) design a crashworthy debris fence mounted on top of a concrete parapet to meet the Manual for Assessing Safety Hardware (MASH) TL-3 crash test conditions. Part 1 of this thesis details the literature review and …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …

Temperature And Stress Analysis During Tank Decanting And Refilling Process, Zhe Liu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

In the present work, an analytical expression for the temperature distribution of the cross-section of a natural gas transport tank is derived by time-matching Green’s Function method. The tank decanting process can produce a living temperature decrease inside the tank wall while the filling process can produce a large temperature increase. This behavior can cause damage to the inner layer of the tank. The damage occurs in the form of excessive stress in the wall which is combined mechanical stress and thermal stress. Therefore, thermo-elasticity analysis is another objective of the present work. A simplified mechanical model is established in …

Coercivity Enhancement And Gamma Phase Avoidance Of Alnico Alloys, Li Zhang

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The promotion of social progress requires greater levels of energy efficiency, quality and productivity. However, these developments usually come at the cost of the environment. Green technologies such as electric vehicles, wind turbine and solar panels are ironically overshadowed by supply limitations and high prices of rare earth elements. Therefore, it is important to find alternative materials to replace those that contain critical elements. Alnico alloys show high magnetization, high Curie temperature (800°C) and good corrosion resistance, making it one of the best candidates to replace neodymium-based magnets used in electric vehicles.

In this thesis, methods controlling shape anisotropy and …

Fundamental Problems In Porous Materials: Experiments & Computer Simulation, Zhanping Xu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Porous materials have attracted massive scientific and technological interest because of their extremely high surface-to-volume ratio, molecular tunability in construction, and surface-based applications. Through my PhD work, porous materials were engineered to meet the design in selective binding, self-healing, and energy damping. For example, crystalline MOFs with pore size spanning from a few angstroms to a couple of nanometers were chemically engineered to show 120 times more efficiency in binding of large molecules. In addition, we found building blocks released from those crystals can be further patched back through a healing process at ambient and low temperatures down to -56 …

Understanding The Effects Of Blast Wave On The Intracranial Pressure And Traumatic Brain Injury In Rodents And Humans Using Experimental Shock Tube And Numerical Simulations, Aravind Sundaramurthy

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Blast induced neurotrauma (BINT) has been designated as the “signature injury” to warfighters in the recent military conflicts. In the past decade, conflicts in Iraq (operation Iraqi freedom) and Afghanistan (operation enduring freedom) as well as the increasing burden of the terrorism around the world resulted in an increased number of cases with blast Traumatic Brain Injury (bTBI). Recently, a lot of research has been done to study the neurological and neurochemical degenerations resulting from BINT using animal models especially rat models. However, it is not clear how and whether the biological outcomes from animal models can be translated to …

Ultrasonic Propagation And Scattering In Pearlitic Steel, Hualong Du

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Diffuse ultrasonic backscatter measurements have been especially useful for extracting microstructural information and for improving flaw detection in materials. In this dissertation, this approach is applied to inspection of railroad wheels. To improve the wear resistance, the tread surfaces of railroad wheels are usually quenched with water to increase the hardness. The pearlite phase of iron, characterized by alternating ferrite and cementite phases, is created by the quenching and the lamellar spacing within grains increases progressively from the quenched tread surface to deeper locations due to the non-uniform cooling rate. The quench depth is an important parameter governing the wheel …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason Gerald Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason G. Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

The Role Of Mechanically Induced Erk Phosphorylation In Stem Cell Adipogenesis, Daniel E. Menter

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Mechanical cell stimulation has only recently been highlighted for its ability to direct cell function and fate. The development of techniques to apply controlled mechanical stimulation to cells has allowed researchers to examine the effects of forces on cell behavior. These studies have shown that cells, and in particular, stem cells are very sensitive to mechanical stimuli. While the potential impact of mechanical forces has been demonstrated by these studies, there have not been many studies that compare the differing effects of stimulation profiles and methods. Further, molecular mechanosensing mechanisms have not been identified. In this work, we compared the …

Propagation Of Thermo-Mechanical Waves In Deforming Nonlinear Viscoelastic Bodies, Lili Zhang

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

This work studies the propagation of thermo-mechanical disturbances in bodies made of viscoelastic materials that might already be loaded such that they are undergoing large inhomogeneous time varying deformations. In the process of this study we develop the general equations governing the thermo-mechanical motion of such disturbances and ones for internally constrained systems, provide the general structure of the solution, match the solution to existing results for the special case of time harmonic plane waves in elastic bodies and in viscoelastic bodies under constant homogenous loading, and consider some special applications.

The results of this work should have applications in …

Mechanics Of Blast Loading On Post-Mortem Human And Surrogate Heads In The Study Of Traumatic Brain Injury (Tbi) Using Experimental And Computational Approaches, Shailesh Govind Ganpule

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Blast induced neurotrauma (BINT) has been designated as the “signature injury” to warfighters in the recent military conflicts. The occurrence of traumatic brain injury (TBI) in blasts is controversial in the medical and scientific communities because the manifesting symptoms occur without visible injuries. Whether the primary blast waves alone can cause mechanical insult that is comparable to existing traumatic brain injury thresholds is still an open question, and this work is aimed to address this issue.

In the first part of this dissertation, mechanics of primary blast loading on Realistic Explosive Dummy (RED) head with and without helmets is studied …

Implementation Of Magnetic Resonance Elastography For The Investigation Of Traumatic Brain Injuries, Thomas Boulet

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Magnetic resonance elastography (MRE) is a potentially transformative imaging modality allowing local and non-invasive measurement of biological tissue mechanical properties. It uses a specific phase contrast MR pulse sequence to measure induced vibratory motion in soft material, from which material properties can be estimated. Compared to other imaging techniques, MRE is able to detect tissue pathology at early stages by quantifying the changes in tissue stiffness associated with diseases. In an effort to develop the technique and improve its capabilities, two inversion algorithms were written to evaluate viscoelastic properties from the measured displacements fields. The first one was based on …

Vibrations Of Crystal Plates With Surface Structures For Resonator And Sensor Applications, Nan Liu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

This dissertation is mainly on the theoretical analysis of vibrating crystal plates for acoustic wave resonator and sensor applications. The frequency and mode effects of different surface structures on either or both sides of the crystal plates are the main concerns in this dissertation. These effects are fundamental to the improvement of existing acoustic wave devices, or to the design of new acoustic wave devices, especially new sensors based on these effects.

At first, two-dimensional equations of motion for an anisotropic crystal plate with two thin films on its surfaces are derived by reduction from the three-dimensional equations of anisotropic …

Fabrication And Characterization Of Biocomposites From Polylactic Acid And Bamboo Fibers, Sarah E. Royse

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Environmental concerns have been motivating research in the field of biodegradable materials, especially those from biological sources. Polylactic acid (PLA) is one biopolymer with the potential to replace some standard synthetic polymers. PLA is currently used for fibers, medical sutures, and some packaging, but is still used very little compared with synthetic polymers. One thing that can be done to expand the potential applications of PLA is to add fibers to create composite materials. Bamboo is a good choice for these fibers because it is abundant in many parts of the world, grows very quickly, and is widely unused. Composites …

Magnetic Properties Study Of The Mn-Al System With Additions Of B Or C And Mechanical Milling Techniques, Timothy E. Prost

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Recently a shift in the focus of permanent magnetic research has moved from Rare Earth (RE)-based alloys to those made from more readily available elements. Because of their relatively large magnetocrystalline anisotropy, L1₀ compounds have the potential for use as permanent magnet materials. One particular alloy that is readily available and inexpensive is near equi-atomic manganese and aluminum (Mn₅₀-Al₅₀). First characterized in 1958, it did not receive much attention until more recently when RE supply chain issues made the alloy more attractive for commercial and research applications. The ferromagnetic (FM) τ-phase (L1₀) is …

Propagation Of Ultrasound Through Freshly Excised Human Calvarium, Armando Garcia Noguera

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The propagation of ultrasound through complex biological media, such as the human calvarium, poses a great challenge for modern medicine. Several ultrasonic techniques commonly used for treatment and diagnosis in most of the human body are still difficult to apply to the human brain, in part, because of the properties of the skull. Moreover, an understanding of the biomechanics of transcranial ultrasound may provide needed insight into the problem of blast wave induced traumatic brain injury (TBI). In the present study, the spatial variability of ultrasonic properties was evaluated for relevant frequencies of 0.5, 1, and 2.25 MHz. A total …

Peridynamic Models For Dynamic Brittle Fracture, Wenke Hu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Damage and failure in composite materials under dynamic loading has been extensively studied in experiments for several decades. Composite materials exhibit various damage and failure patterns under different loading rates, such as splitting and branching. Classical models cannot directly be applied to problems with discontinuous fields. A new nonlocal continuum model, peridynamics, has been proposed with the goal of solving dynamic fracture problems.

The J-integral has the physical significance of energy flow into the crack tip region. We present a rigorous derivation for the formulation of the J-integral in peridynamics using the crack infinitesimal virtual extension approach. We …

Generic Strategies To Implement Material Grading In Finite Element Methods For Isotropic And Anisotropic Materials, Ke Yu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

We look at generic strategies to transfer material grading into finite element methods. Three strategies are proposed to transfer material grading into the finite element analysis. These strategies are node-centered, element-centered, and the definition of material grading through external functions. The process to achieve each strategy is stated, and examples are used to illustrate each strategy, and to compare them. The strategies are implemented in finite-deformation nonlinear elastic analysis.

Several examples are used to illustrate the implementation of each strategy for graded isotropic materials. For these examples, the results obtained from finite element models are compared with those obtained from …

Effect Of Extracellular Matrix (Ecm) Protein Micropatterns On The Behavior Of Human Neuroblastoma Cells, Ishwari Poudel

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Recent advances in patterning techniques and emerging surface microtechnologies have allowed cell micropatterning to control spatial location of the cells on a surface as well as cell shape, attachment area, and number of contacting neighbor cells. These parameters play important roles in cell cellular behaviors. Cell micropatterning has thus become one of the most important strategies for biomedical applications, such as, tissue engineering, diagnostic immunoassays, lab-on-chip devices, bio-sensing, etc., and cell biology studies as well. For neuronal cells, there have been attempts to distribute neuronal cells on specific patterns to control cell-to-cell interaction. However, there have been very limited understanding …

Strength Of Polycrystalline Ceramics Under Shock Compression, Jianbin Zhu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Determinations of Some polycrystalline ceramics’ strength properties and inelastic deformation mechanisms in the shocked state are critically important to the design and optimization of armor structures involving these materials. In this work, multiscale modeling and simulations have been carried out to study strength of the effects of polycrystalline microstructure, crystal anisotropy, porosity, and their interactions with microscopic deformation/damage mechanisms on the responses of several polycrystalline ceramics under shock compression and to extract their shock strengths from the wave profiles measured in the related plate impact shock wave experiments.

With a mesoscopic computational model, the roles of intragranular microplasticity and deformation …

Ultrasonic Methods For The Characterization Of Complex Materials And Material Systems: Polymers, Structured Polymers, Soft Tissue And Bone, Charles Landais

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Understanding the characteristics and structure of materials is of importance in proper modeling and effective design of many products. Complex materials such as polymers, structured material systems, or biological materials provide a particular challenge to many of the traditional methods for doing this. In this dissertation I study the use of ultrasonic wave techniques to characterize several complex materials. These include plastically deformed and aged polycarbonate (PC), a structured PC plate with water filled cavities, bovine bone, and an elastomer used as a skin simulant. In each case, this work was part of a larger project that studied different aspects …

Ultrasonic And Stereo-Optical Characterization Techniques For Applications In Mechanical Testing, Jonathan M. Hein

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

This thesis considers methods developed based on ultrasonic reflections from interfaces and stereo-optical surface strain measurements to study the mechanical characterization of materials and bodies. The ultrasonic method is used to characterize wave speed and attenuation for highly attenuating samples. The stereo-optical strain measurements are used to characterize the effects of genes on mechanical properties of bone, and the dynamic characterization of blast waves in the UNL Shock Wave Trauma Mechanics facility.

A method is described and developed for characterizing the wave speed and attenuation spectrums from reflected waves from the contact surface with an unknown material. The method is …

A Peridynamic Formulation For Transient Heat Conduction In Bodies With Evolving Discontinuities, Monchai Duangpanya

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Modeling heat flow in bodies with discontinuities, such as cracks, or with inclusions that have different thermal properties has been a very challenging problem. Classical models lead to infinite heat fluxes at the tip of a crack and convergence of numerical methods that approximate solutions to such models have convergence and mesh dependency issues. To remove the difficulties faced by the classical models a novel nonlocal theory is formulated.
The new theory starts from the conservation of energy principle and uses the idea of nonlocal heat-transfer between material points. This idea leads to a transient heat transfer model that does …

A Shock Tube Technique For Blast Wave Simulation And Studies Of Flow Structure Interactions In Shock Tube Blast Experiments, Nicholas N. Kleinschmit

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Improvised explosive devices (IED’s) are widely used against US and allied forces fighting in Iraq and Afghanistan. Exposure to IED blast may cause blast-induced traumatic brain injury (bTBI). The injury mechanisms are however not well understood. A critical need in bTBI-related research is the ability to replicate the loading conditions of IED blast waves in a laboratory environment. In this work, experimental studies have been carried out to explore the use of the shock tube technique for generating air shock waves that mimic the temporal and spatial characteristics of free-field blast waves and to investigate the blast wave-test sample interactions …

Hybrid Nanomanufacturing Process For High-Rate Polymer Nanofiber Production, Chad T. Peterson

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Nanotechnology and nanomaterials have the potential to revolutionize existing and create entirely new industries. Unique physical, mechanical, chemical, and biological properties of nanomaterials have been extensively documented in the last two decades. However, most nanomaterials are discontinuous in nature, creating problems with their processing and manipulation into devices and raising health concerns. Continuous nanofibers represent an emerging class of nanomaterials with critical advantages to applications. Continuous nanofibers are readily produced by electrospinning process comprising spinning polymer solutions in high electric fields. Electrospinning is a very economic top-down nanomanufacturing process that has been used to produce ultrafine continuous nanofibers from several …

Anomalous Loss Of Toughness Of Work Toughened Polycarbonate, Shawn E. Meagher

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Glassy polymers such as polycarbonate (PC) can be toughened through compressive plastic deformation. The increase in toughness is substantial, showing as much as a fifteen fold increase in the amount of dissipated energy during failure for samples compressed to 50% plastic strain. This toughness increase can be reversed through thermal aging at temperatures below the glass transition temperature (T_g = 147°C).

The combined effect of plastic compression and thermal aging has been studied using Charpy, Single Edge Notch Bending (SENB), and Compact Tension (CT) tests. The tests mapped the response of samples cut along different orientations relative to the …

Development And Characterization Of Shock Tubes For Laboratory Scale Blast Wave Simulation, Aaron D. Holmberg

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The prevalence of traumatic brain injury (TBI) in American soldiers exposed to a blast wave has created an urgent need to better understand the effects of blast wave insult to the head. Developing techniques that can experimentally simulate well controlled blast waves in a laboratory environment is a critical component of the research efforts towards this goal. For this work, a 4-in. cylindrical uniform shock tube and a nonuniform shock tube combining a 4-in. cylindrical gas driver with a 9-in. square driven section have been developed. The hosting laboratory, gas handling system, multichannel data acquisition systems, and the related network …

Nanomanufacturing And Analysis Of Novel Integrated Continuous Nanofibers, John E. Hannappel

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Complex nanostructured materials have great potential for applications in many areas of nanotechnology. This potential is being unlocked by precise control of their nanoscale architecture and properties. Most current methods of creating these nanostructures are expensive and difficult to control, with the majority of techniques resulting in non-continuous nanostructures and nanoparticles. Electrospinning is an economic nanomanufacturing method resulting in continuous nanofibers. The method consists of spinning fiber-forming liquids in high electric fields. In this work, a modified electrospinning process was analyzed. The process utilized two concentric liquids that resulted in integrated continuous hollow or composite nanofibers. A new adjustable co-axial …

Fracture Of Bone Using Microindentation, Séverine Vennin

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Osteoporosis is a current disease which is especially of concern to post-menopausal women. It is characterized by a decrease of bone density and an increase in the risk of fracture. Interest in the fracture mechanisms with respect to the underlying biological structure of the bone is of great interest to researchers in this field. In this thesis, a new method based on microindentation on rat femurs was developed to determine the relation between the viscoelastic and the fracture properties of bone. The main goal is to measure the viscoelastic properties by using a dynamic mechanical analysis indentation method and then …