Engineering Commons^™

Spectrally Shaped Generalized Mc-Ds-Cdma With Dual Band Combining For Increased Diversity, Wenhui Xiong, David W. Matolak

Faculty Publications

A new multicarrier spread spectrum modulation scheme is proposed in this paper. This scheme uses sinusoidal chip waveforms to shape the spectrum of each subcarrier of a multicarrier direct sequence spread spectrum (DS-SS) signal. As a result, each subcarrier has two distinct spectral lobes, one a lower sideband (LSB) and the other an upper sideband (USB). By properly selecting the parameters of the sinusoidal chip waveforms, the two sideband signals can be made to undergo independent fading in a dispersive fading channel. These two independently-faded sideband signals, when combined at the receiver, provide diversity gain to the system. Our analysis …

Gene Rearrangement Analysis And Ancestral Order Inference From Chloroplast Genomes With Inverted Repeat, Feng Yue, Liying Cui, Claude W. Depamphilis, Bernard M.E. Moret, Jijun Tang

Faculty Publications

Background
Genome evolution is shaped not only by nucleotide substitutions, but also by structural changes including gene and genome duplications, insertions, deletions and gene order rearrangements. The most popular methods for reconstructing phylogeny from genome rearrangements include GRAPPA and MGR. However these methods are limited to cases where equal gene content or few deletions can be assumed. Since conserved duplicated regions are present in many chloroplast genomes, the inference of inverted repeats is needed in chloroplast phylogeny analysis and ancestral genome reconstruction.

Results
We extend GRAPPA and develop a new method GRAPPA-IR to handle chloroplast genomes. A test of GRAPPA-IR …

Wideband Smaller Unit-Cell Planar Ebg Structures And Their Application, M. Faisal Abedin, Mohammed Z. Azad, Mohammod Ali

Faculty Publications

A new low-cost smaller unit-cell planar electromagnetic bandgap (ERG) structure operating at the lower GHz frequencies (below 6 GHz) is proposed. ERG structures based on this new geometry are designed on a number of commonly available substrates. Characteristics of such structures, such as bandgap and reflection phase profile are analyzed. a simple empirical model is proposed to predict the surface wave stopband frequency of the proposed ERG structure. Finally, a low-profile dipole antenna is designed and tested for operation on the ERG structure.

Globally Optimal Grouping For Symmetric Closed Boundaries By Combining Boundary And Region Information, Joachim S. Stahl, Song Wang

Faculty Publications

Many natural and man-made structures have a boundary that shows a certain level of bilateral symmetry, a property that plays an important role in both human and computer vision. In this paper, we present a new grouping method for detecting closed boundaries with symmetry. We first construct a new type of grouping token in the form of symmetric trapezoids by pairing line segments detected from the image. A closed boundary can then be achieved by connecting some trapezoids with a sequence of gap-filling quadrilaterals. For such a closed boundary, we define a unified grouping cost function in a ratio form: …

Enhanced Dielectric Properties In Single Crystal-Like Bifeo3 Thin Films Grown By Flux-Mediated Epitaxy, S.-H. Lim, M. Murakami, J. H. Yang, S.-Y. Young, Jason R. Hattrick-Simpers, M. Wuttig, L. G. Salamanca-Riba, I. Takeuchi

Faculty Publications

We have fabricated single crystal-like BiFeO₃ (BFO) thin films by flux-mediated epitaxy using pulsed laser deposition(PLD). The Bi–Cu–O flux composition and its thickness were optimized using composition spread, thickness gradient, and temperature gradient libraries. The optimized BFO thin films grown with this technique showed larger grain size of ∼2μm and higher dielectric constant in the range of 260–340 than those for standard PLD grown films. In addition, the leakage current density of the films was reduced by two orders of magnitude compared to that of standard PLD grown films.

Elastic Wave Field Computation In Multilayered Nonplanar Solid Structures: A Mesh-Free Semianalytical Approach, Sourav Banerjee, Tribikram Kundu

Faculty Publications

Multilayered solid structures made of isotropic, transversely isotropic, or general anisotropic materials are frequently used in aerospace, mechanical, and civil structures. Ultrasonic fields developed in such structures by finite size transducers simulating actual experiments in laboratories or in the field have not been rigorously studied. Several attempts to compute the ultrasonic field inside solid media have been made based on approximate paraxial methods like the classical ray tracing and multi-Gaussian beam models. These approximate methods have several limitations. A new semianalytical method is adopted in this article to model elastic wave field in multilayered solid structures with planar or nonplanar …

Web-Scale Workflow: Integrating Distributed Services, M. Brian Blake, Michael N. Huhns

Faculty Publications

Modular applications, components, and services are all ways of describing the product of an organization's efforts to embody its capabilities in autonomous software modules. In fact, the integration of services using well-established workflow paradigms could amplify an organization's capabilities with the creation of a full-blown, inter-organizational system of systems. This is the essence of Web-scale workflows. Considering the recent popularity and acceptance of service-oriented technologies, the application of such distributed systems is only limited by imagination, but it's also important to understand existing research challenges and their implications to various Web-scale workflow domains.

Hydrogen Peroxide Formation Rates In A Pemfc Anode And Cathode: Effect Of Humidity And Temperature, Vijay A. Sethuraman, John W. Weidner, Andrew T. Haug, Sathya Motupally, Lesia V. Protsailo

Faculty Publications

Hydrogen peroxide (H₂O₂) formation rates in a proton exchange membrane fuel cell (PEMFC) anode and cathode were estimated as a function of humidity and temperature by studying the oxygen reduction reaction (ORR) on a rotating ring disk electrode. Fuel cell conditions were replicated by depositing a film of Pt/Vulcan XC-72 catalyst onto the disk and by varying the temperature, dissolved O₂ concentration, and the acidity levels in hydrochloric acid (HClO₄). The HClO₄ acidity was correlated to ionomer water activity and hence fuel cell humidity. The H₂O₂ formation rates showed …

Analytical Expression For The Impedance Response For A Lithium-Ion Cell, Godfrey Sikha, Ralph E. White

Faculty Publications

An analytical expression to predict the impedance response of a dual insertion electrode cell (insertion electrodes separated by an ionically conducting membrane) is presented. The expression accounts for the reaction kinetics and double-layer adsorption processes at the electrode-electrolyte interface, transport of electroactive species in the electrolyte phase, and insertion of species in the solid phase of the insertion electrodes. The accuracy of the analytical expression is validated by comparing the impedance response predicted by the expression to the corresponding numerical solution. The analytical expression is used to predict the impedance response of a lithium-ion cell consisting of a porous LiCoO …

Combinatorial Investigation Of Magnetostriction In Fe-Fa And Fe-Ga-Al, Jason R. Hattrick-Simpers, Dwight Hunter, Corneliu M. Craciunescu, Kyu Sung Jang, Makoto Murakami, James Cullen, Manfred Wuttig, Ichiro Takeuchi, Samuel E. Lofland, Leonid Bendersky, Noble Woo, Robert Bruce Vandover, Toshiya Takahashi, Yasubumi Furuya

Faculty Publications

A high-throughput high-sensitivity optical technique for measuringmagnetostriction of thin-film composition-spread samples has been developed. It determines the magnetostriction by measuring the induced deflection of micromachined cantilever unimorph samples. Magnetostrictionmeasurements have been performed on as-deposited Fe–Ga and Fe–Ga–Al thin-film composition spreads. The thin-film Fe–Ga spreads display a similar compositional variation of magnetostriction as bulk. A previously undiscovered peak in magnetostriction at low Ga content was also observed and attributed to a maximum in the magnetocrystalline anisotropy. Magnetostrictive mapping of the Fe–Ga–Al ternary system reveals the possibility of substituting up to 8at.%Al in Fe₇₀Ga₃₀ without significant degradation of magnetostriction.

High-Throughput Screening Of Shape Memory Alloy Thin-Film Spreads Using Nanoindentation, Arpit Dwivedi, Thomas J. Wyrobek, Oden L. Warren, Jason R. Hattrick-Simpers, Olubenga O. Famodu, Ichiro Takeuchi

Faculty Publications

We have demonstrated the utility of nanoindentation as a rapid characterization tool for mapping shape memoryalloy compositions in combinatorial thin-film libraries. Nanoindentation was performed on Ni–Mn–Al ternary composition spreads. The indentation hardness and the reduced elastic modulus were mapped across a large fraction of the ternary phase diagram. The large shape memoryalloy composition region, located around the Heusler composition (Ni₂MnAl), was found to display significant departure in these mechanical properties from the rest of the composition spread. In particular, the modulus and the hardness values are lower for the martensite region than those of the rest of the …

Acceptor Levels In Gase:In Crystals Investigated By Deep-Level Transient Spectroscopy And Photoluminescence, Y. Cui, R. Dupere, A. Burger, D. Johnstone, K. C. Mandal, S. A. Payne

Faculty Publications

No abstract provided.

Durability Of Perfluorosulfonic Acid And Hydrocarbon Membranes: Effect Of Humidity And Temperature, Vijay A. Sethuraman, John W. Weidner, Andrew T. Haug, Lesia V. Protsailo

Faculty Publications

The effect of humidity on the chemical stability of two types of membranes [i.e., perfluorosulfonic acid type (PFSA, Nafion 112) and biphenyl sulfone hydrocarbon type, (BPSH-35)] was studied by subjecting the membrane electrode assemblies (MEAs) to open-circuit voltage (OCV) decay and potential cycling tests at elevated temperatures and low inlet-gas relative humidities. The BPSH-35 membranes showed poor chemical stability in ex situ Fenton tests compared to that of Nafion membranes. However, under fuel cell conditions, BPSH-35 MEAs outperformed Nafion 112 MEAs in both the OCV decay and potential cycling tests. For both membranes, (i) at a given temperature, …

The Role Of Filler-Matrix Interaction On Viscoelastic Response Of Biomimetic Nanocomposite Hydrogels, Alireza S. Sarvestani, Xuezhong He, Esmaiel Jabbari

Faculty Publications

The effect of a glutamic acid (negatively charged) peptide (Glu6), which mimics the terminal region of the osteonectin glycoprotein of bone on the shear modulus of a synthetic hydorgel/apatite nanocomposite, was investigated. One end of the synthesized peptide was functionalized with an acrylate group (Ac-Glu6) to covalently attach the peptide to the hydrogel phase of the composite matrix. The addition of Ac-Glu6 to hydroxyapatite (HA) nanoparticles (50 nm in size) resulted in significant reinforcement of the shear modulus of the nanocomposite (~100% increase in elastic shear modulus). The reinforcement effect of the Glu6 peptide, a sequence in the terminal region …

Thermal Model For A Li-Ion Cell, Karthikeyan Kumaresan, Godfrey Sikha, Ralph E. White

Faculty Publications

A thermal model for a lithium-ion cell is presented and used to predict discharge performance at different operating temperatures. The results from the simulations are compared to experimental data obtained from lithium-ion pouch cells. The model includes a set of parameters (and their concentration and temperature dependencies) that has been obtained for a lithium-ion cell composed of a mesocarbon microbead anode, LiCoO₂ cathode in 1 M LiPF₆ salt, in a mixture of ethylene carbonate, propylene carbonate, ethyl-methyl carbonate, and diethyl carbonate electrolyte. The parameter set was obtained by comparing the model predictions to the experimental discharge profiles obtained …

Parameter Estimation And Life Modeling Of Lithium-Ion Cells, Shriram Santhanagopalan, Qi Zhang, Karthikeyan Kumaresan, Ralph E. White

Faculty Publications

Lithium-ion pouch cells were cycled at five different temperatures (5, 15, 25, 35, and 45°C ), and rate capability studies were performed after every hundred cycles. The data were used with a simple physics-based model to estimate parameters that capture the capacity fade in the cell, with cycling. The weight of active material within each electrode was estimated as a function of time, using rate capability data at the C/33 rate. The C-rate for these cells is 1.656 A. The capacity fade due to the loss of active material and that due to the loss of cyclable lithium …

A Mathematical Model For A Lithium–Sulfur Cell, Karthikeyan Kumaresan, Yuriy Mikhaylik, Ralph E. White

Faculty Publications

A mathematical model is presented for a complete lithium–sulfur cell. The model includes various electrochemical and chemical (precipitation) reactions, multicomponent transport phenomena in the electrolyte, and the charge transfer within and between solid and liquid phases. A change in the porosity of the porous cathode and separator due to precipitation reactions is also included in the model. The model is used to explain the physical reasons for the two-stage discharge profiles that are typically obtained for lithium–sulfur cells.

). Size Dependency Of The Elastic Modulus Of Zno Nanowires: Surface Stress Effect, Guofeng Wang, Xiaodong Li

Faculty Publications

Relation between the elastic modulus and the diameter (D) of ZnOnanowires was elucidated using a model with the calculated ZnOsurface stresses as input. We predict for ZnOnanowires due to surface stress effect: (1) when D>20nm, the elastic modulus would be lower than the bulk modulus and decrease with the decreasing diameter, (2) when 20nm>D>2nm, the nanowires with a longer length and a wurtzite crystal structure could be mechanically unstable, and (3) when D<2nm, the elastic modulus would be higher than that of the bulk value and increase with a decrease in nanowire diameter.

Wireless Power Transmission To A Buried Sensor In Concrete, Khan M.Z. Shams, Mohammod Ali

Faculty Publications

The feasibility of sending wireless power to a buried sensor antenna within concrete was studied. a receive patch rectenna with 75.8% conversion efficiency was designed for operation at 5.7 GHz. The received DC power at the rectenna was measured within dry and wet concrete samples with various cover thicknesses and air-gaps. For the rectenna buried within 30 mm of the concrete, the received DC power was 10.37 mW, which was, about 70% of the received DC power in free-space.

Are There Rearrangement Hotspots In The Human Genome?, Max A. Alekseyev, Pavel A. Pevzner

Faculty Publications

In a landmark paper, Nadeau and Taylor [18] formulated the random breakage model (RBM) of chromosome evolution that postulates that there are no rearrangement hotspots in the human genome. In the next two decades, numerous studies with progressively increasing levels of resolution made RBM the de facto theory of chromosome evolution. Despite the fact that RBM had prophetic prediction power, it was recently refuted by Pevzner and Tesler [4], who introduced the fragile breakage model (FBM), postulating that the human genome is a mosaic of solid regions (with low propensity for rearrangements) and fragile regions (rearrangement hotspots). However, the rebuttal …

Nanoindentation Of The A And C Domains In A Tetragonal Batio3 Single Crystal, Young-Bae Park, Matthew J. Dicken, Zhi-Hui Xu, Xiaodong Li

Faculty Publications

Nanoindentation in conjunction with piezoresponse force microscopy was used to study domain switching and to measure the mechanical properties of individual ferroelectric domains in a tetragonal BaTiO₃ single crystal. It was found that nanoindentation has induced local domain switching; the a and c domains of BaTiO₃ have different elastic moduli but similar hardness.Nanoindentationmodulus mapping on the a and c domains further confirmed such difference in elasticity. Finite element modeling was used to simulate the von Mises stress and plastic strain profiles of the indentations on both a and c domains, which introduces a much higher stress level than …

Edge Grouping Combining Boundary And Region Information, Joachim S. Stahl, Song Wang

Faculty Publications

This paper introduces a new edge-grouping method to detect perceptually salient structures in noisy images. Specifically, we define a new grouping cost function in a ratio form, where the numerator measures the boundary proximity of the resulting structure and the denominator measures the area of the resulting structure. This area term introduces a preference towards detecting larger-size structures and, therefore, makes the resulting edge grouping more robust to image noise. To find the optimal edge grouping with the minimum grouping cost, we develop a special graph model with two different kinds of edges and then reduce the grouping problem to …

Silicon Dioxide-Encapsulated High-Voltage Algan/Gan Hfets For Power-Switching Applications, N. Tipirneni, V. Adivarahan, Grigory Simin, Asif Khan

Faculty Publications

In this letter, new approach in achieving high breakdown voltages in AlGan/GaN heterostructure field-effect transistors (HFETs) by suppressing surface flashover using solid encapsulation material is presented. Surface flashover in III-Nitride-based HFETs limits the operating voltages at levels well below breakdown voltages of GaN. This premature gate-drain breakdown can be suppressed by immersing devices in high-dielectric-strength liquids (e.g., Fluorinert); however, such a technique is not practical. In this letter, AlGan/GaN HFETs encapsulated with PECVD-deposited SiO2 films demonstrated breakdown voltage of 900 V, very similar to that of devices immersed in Fluorinert liquid. Simultaneously, low dynamic ON-resistance of 2.43 m Omega. cm(2) …

Localization With Limited Sensing, Jason M. O'Kane, Steven M. Lavalle

Faculty Publications

Localization is a fundamental problem for many kinds of mobile robots. Sensor systems of varying ability have been proposed and successfully used to solve the problem. This paper probes the lower limits of this range by describing three extremely simple robot models and addresses the active localization problem for each. The robot, whose configuration is composed of its position and orientation, moves in a fully-known, simply connected polygonal environment. We pose the localization task as a planning problem in the robot's information space, which encapsulates the uncertainty in the robot's configuration. We consider robots equipped with: 1) angular and linear …

Adaptive Control Strategy For Active Power Sharing In Hybrid Fuel Cell/Battery Power Sources, Zhenhua Jiang, Lijun Gao, Roger A. Dougal

Faculty Publications

Hybrid systems composed of fuel cells and batteries combine the high energy density of fuel cells with the high power density of batteries. A dc/dc power converter is placed between the fuel cell and the battery to balance the power flow between them and greatly increase the peak output power of the hybrid. This paper presents an adaptive control strategy for active power sharing in the hybrid power source. This control strategy can adjust the output current setpoint of the fuel cell according to the state-of-charge (or voltage) of the battery, and is applicable in two topologies of active fuel …

Fpga Acceleration Of Gene Rearrangement Analysis, Jason D. Bakos

Faculty Publications

In this paper we present our work toward FPGA acceleration of phylogenetic reconstruction, a type of analysis that is commonly performed in the fields of systematic biology and comparative genomics. In our initial study, we have targeted a specific application that reconstructs maximum-parsimony (MP) phylogenies for gene-rearrangement data. Like other prevalent applications in computational biology, this application relies on a control-dependent, memory-intensive, and non-arithmetic combinatorial optimization algorithm. To achieve hardware acceleration, we developed an FPGA core design that implements the application's primary bottleneck computation. Because our core is lightweight, we are able to synthesize multiple cores on a single FPGA. …

Investigation Of Cdznte Crystal Defects Using Scanning Probe Microscopy, Goutam Koley, J. Liu, K. C. Mandal

Faculty Publications

No abstract provided.

Lightweight Error Correction Coding For System-Level Interconnects, Jason D. Bakos, Donald M. Chiarulli, Steven P. Levitan

Faculty Publications

"Lightweight hierarchical error control coding (LHECC)" is a new class of nonlinear block codes that is designed to increase noise immunity and decrease error rate for high-performance chip-to-chip and on-chip interconnects. LHECC is designed such that its corresponding encoder and decoder logic may be tightly integrated into compact, high-speed, and low-latency I/O interfaces. LHECC operates over a new channel technology called multi-bit differential signaling (MBDS). MBDS channels utilize a physical-layer channel code called "N choose M (nCm)" encoding, where each channel is restricted to a symbol set such that half of the bits in each symbol are set to one. …

A Reconfigurable Stacked Microstrip Patch Antenna For Satellite And Terrestrial Links, Mohammod Ali, Abu T.M. Sayem, Vijay K. Kunda

Faculty Publications

A reconfigurable stacked microstrip patch antenna is proposed. The antenna operates at an upper frequency f(u) with a broadside pattern, 7.5-dBi right-hand circularly polarized gain, and 15.8% bandwidth. At a lower frequency f(1), the antenna operates as a planar inverted-F antenna (7.3% bandwidth and 3.9-dBi peak gain) with the main beam directed close to the horizon. Switching between the two regimes of operation is achieved using p-i-n diodes. antenna operation in the upper frequency hand is suitable for low-earth-orbit or medium-earth-orbit satellite communications, and in the lower frequency band, the antenna is useful for terrestrial land-mobile or other wireless applications.

Threshold Power Of Canonical Antennas For Inducing Sar At Compliance Limits In The 300-3000 Mhz Frequency Range, Mohammod Ali, Mark G. Douglas, Abu T.M. Sayem, Antonio Faraone, Chung-Kwang Chou

Faculty Publications

A study of the specific absorption rate (SAR) in an exposed body induced by canonical antennas is presented, with the aim of determining an upper bound for the antenna transmit power that demonstrates that a product is inherently compliant with internationally accepted radio frequency (RF) exposure limits. Starting from the fundamental limits in antenna quality factor (Q) and the corresponding bandwidth, several antenna sizes are selected, and their SAR distributions are computed using the method of moments (MoM) and finite-difference time domain (FDTD) method in the frequency range 300-3000 MHz. The threshold powers are then determined, below which the peak …