Open Access. Powered by Scholars. Published by Universities.®
- Publication Year
- File Type
Articles 61 - 90 of 633
Full-Text Articles in Public Policy
Ddasaccident670, Hd-Aid
Ddasaccident670, Hd-Aid
Global CWD Repository
While the deminer was working in his lane by the end of the working day, he tried to move one AP (M35) mine partially covered in the ground against of the TL instructions using the light RAKE, the mine initiated 1.8 m away from the deminer and caused the wounds and the mentioned injures to the deminer that he wasn’t wearing the visor in the proper way
Ddasaccident628, Hd-Aid
Ddasaccident628, Hd-Aid
Global CWD Repository
Deminer was clearing the first 60 cm of one cluster heading toward the centre mine after he cleared the 1st 60 cm by one 1m width with no signals he moved his base stick a head to clear the next 60 cm, then he stepped on the area which considered to be cleared by the same deminer, accidently his foot went down due to the soil collapse under his foot (loose soil), the mine was in a depth of about 30 cm that when the deminer foot dived in the loosen soil he applied a pressure on the mine which …
Ddasaccident624, Hd-Aid
Ddasaccident624, Hd-Aid
Global CWD Repository
The primary cause of this accident is listed as a Field Control inadequacy because the investigators found that there was poor supervision at the time of the accident. The secondary cause is listed as Other because there is not enough detail in the summary to determine what the deminer was doing, and what tool he was using.
Ddasaccident702, Hd-Aid
Ddasaccident702, Hd-Aid
Global CWD Repository
On 28 July 2009 at 08:10 hrs when Ahmed de-miner was working on a signal in his clearance lane by using a pickaxe instead of bayonet, he hit the mine on its top and caused it to go off. According to the investigation report the ground surface was uneven, hard and impossible to work in sitting position, so he has started to investigate the signal in standing position. This was the main reason of initiating mine and accident.
Ddasaccident669, Hd-Aid
Ddasaccident669, Hd-Aid
Global CWD Repository
Deminer Was Clearing the first 60 cm from the centre lane on a depth of 30 cm using the heavy RAKE after he done with the light rake , deminer hit the M14 mine on a depth of 35 cm by the heavy rake which initiate the mine. [The depth appears to be an error, and should perhaps be 15cm.]
Ddasaccident649, Hd-Aid
Ddasaccident649, Hd-Aid
Global CWD Repository
On 13 August 2009 at 07:15 am while [the victim] deminer was excavating a excavating a dog indication in an access lane, his pick touched on the top of PMN 2 anti-personnel mine and caused it to go off. According to the investigation report the deminer has used the pickaxe to investigate the signal found in dog indication instead of the bayonet and it seems as he used the pick directly on the top of signal, so hit the mine and caused the accident. From the location of injuries it seems the deminer has not used his PPE and visor …
Ddasaccident642, Hd-Aid
Ddasaccident642, Hd-Aid
Global CWD Repository
While the deminer was clearing the lane from stones using the light rake he removed the stones not behind him but he conducted a violation of drill and he threw the stones to the left side of the safe lane and one of the stone hit the unknown mine 12 meters forward to the Syrian side at IOE to the contaminated area resulting mine blast.
Ddasaccident705, Hd-Aid
Ddasaccident705, Hd-Aid
Global CWD Repository
The deminer was looking for a missing mine (M14) in the cluster and the metal detector indicated a very weak signal, the deminer started to investigated that signal then the mine initiated that the deminer wasn’t following the proper procedure to approach the mine
Ddasaccident681, Hd-Aid
Ddasaccident681, Hd-Aid
Global CWD Repository
On 21 July 2009 while deminer [the Victim] was working in his clearance lane, investigating a detected signal with his hand trowel, he hit a mine on its top and caused it to go off. The weather was hot and the ground surface was hard and dry, so it seems that the deminer had used his excavation tool by force and carelessly and directly on pinpointed spot so touched the top of mine and caused the accident. As the deminer was dressed with PPE (vest, helmet and visor according to [Demining group] SOPs), so his face, neck and chest remained …
Ddasaccident675, Hd-Aid
Ddasaccident675, Hd-Aid
Global CWD Repository
Narrative: While the deminer was trying to investigate a signal using the heavy RAKE and after he pinpointed it , and finished with the light RAKE the deminer hit the non visible AP mine (M14) by the heavy RAKE on the pressure plate which initiated the mine 2.2 metres away from the deminer.
Ddasaccident752, Hd-Aid
Ddasaccident752, Hd-Aid
Global CWD Repository
On 1st July 2009 MU-16 of [Demining group] started clearance operation on mentioned task. On 08 July 2009 at 0919hrs while [the Victim] was investigating a signal in his clearance lane, he found two bullets. He re-checked the spot and found the same signal, this process repeated for three times. Finally he found a root stump in the excavation trench with a thickness of around 2.5 cm and started to remove it, because it was blocking further excavation there. However the deminer had proper tool in his toolkit to cut such obstacles, but he tried to cut it with his …
Ddasaccident623, Hd-Aid
Ddasaccident623, Hd-Aid
Global CWD Repository
The incident caused by individual mistake while the deminer using the heavy RAKE in a hacking motion not as the proper procedure the Raking motion, and most of the mines in the area are surfaces mines that they can be recovered just with the usage of the light RAKE even if that will cost the deminer more sweat but it will still safer.
Ddasaccident604, Hd-Aid
Ddasaccident604, Hd-Aid
Global CWD Repository
While the deminer try to investigate a signal in lane 15 (12 O’clock mine) he didn’t approached the mine in the proper procedure which caused the deminer to hit the mine from the top of the pressure plate and initiate the mine 2.2 m away from the deminer (the distance of the heavy RAKE).
Ddasaccident712, Hd-Aid
Ddasaccident712, Hd-Aid
Global CWD Repository
On 18 April 2009 [Demining group] DT-05 started clearance operation on mentioned task, they cleared around 19830 sqm area and found/destroyed 4 anti-personnel mines and 2 UXO till the accident time. On 27 June 2009 at 11:15 am the deminer [the Victim] was working in his clearance lane, he found a signal behind some stones, the investigation of signal was impossible with bayonet so he informed the section leader and sought his advice. Section leader instructed him to use pick, but a stone in front of pinpointed signal did not let the pick to be used easily. Therefore, the deminer …
Ddasaccident690, Hd-Aid
Ddasaccident690, Hd-Aid
Global CWD Repository
Today afternoon one mine blast at Al Kaider 4, Team 5 (female deminer team) at 1550 hrs, deminer [the Victim] received the first aid treatment by the medic onsite, a superficial wound (4 to 6 mm) X 2 in her Lt. upper side of the arm, and no any other injuries noticed. Deminer evacuated to KAUH where she received cleaning and dressing of the wounds, X-ray done to clear no any fragmentations in the Arm, deminer received Anti Tetanus and Antibiotics and discharged from the hospital at 1710hrs, No sick leave given by KAUH doctors. Deminer advised to reach the …
Ddasaccident686, Hd-Aid
Ddasaccident686, Hd-Aid
Global CWD Repository
On 1st of June [Demining group] started clearance operation on mentioned task, they cleared 3350 sqm and found/destroyed 150 anti-personnel and 90 UXO till the accident time. On 23 June 2009 at 08:40 am when [the Victim] was working in his clearance lane a PMN2 antipersonnel mines went off and caused the accident. However the deminer had worn his PPE but he got some injures on his both legs, fortunately the injuries were not severe. According to the investigation report the ground was hard to conduct excavation easily, however the MDU was used for ground preparation, but it was failed …
Ddasaccident682, Hd-Aid
Ddasaccident682, Hd-Aid
Global CWD Repository
At 07:25 am the 21st of June 2009 while am working on 9 o’clock mine in section 4 Sabha 8, I was following all the procedures in the manual clearing and after I finished the first box I used the light rake first and when it was not responding to the hard ground I turned to the heavy rake to release the upper layer of the sand and grass, I pulled using the heavy rake then the accident happened suddenly while am working.
Ddasaccident734, Hd-Aid
Ddasaccident734, Hd-Aid
Global CWD Repository
[Demining group] is subcontracted by US-DOD for mine clearance in Bagram Air Field. On 15 June 2009, when the [Demining group] US-DOD related team was working on a BAC task inside the BAF, experienced an uncontrolled detonation. The accident happened when [the Victim] the deminer was excavating a detected signal using a small pick; he found a metal plate and decided to excavate beneath the metal plate, during the excavation drill his excavation tool might touched the mine and caused it to go off.
Ddasaccident633, Hd-Aid
Ddasaccident633, Hd-Aid
Global CWD Repository
AF/2008/00324/H4533-13 is an anti-personnel mine contaminated area laid by the government forces during the Russian invasion in Afghanistan. The mines are laid in 2 rows as a belt surrounding Kandak-e-921 Sarhadi in order to secure their positions from the attacks of Mujahedeen. [Demining group] DT-18 was tasked for the clearance of mentioned area, on 9th of June 2009 at 07:55 am deminer [Victim No.1] was working in his clearance lane excavating a detected signal, his prodder touched a mine and caused it to explode. According to the investigation report the signal was not pinpointed correctly and the deminer has used …
Ddasaccident757, Hd-Aid
Ddasaccident757, Hd-Aid
Global CWD Repository
On 07 June 1035 hours [the Victim] the section leader of mentioned team stopped his deminer [Name removed] and started to work instead of him as the deminer was getting tired. He hit the top of a mine with his prodding tool so the accident occurred. There is a wound with regular edges on the forehead of section leader and some abrasions on his face and left eye. The PPE was used during the operation, but the visor was broken down by a forceful back out of excavation tool possibly the shovel and caused the injury to him. According to …
Ddasaccident610, Hd-Aid
Ddasaccident610, Hd-Aid
Global CWD Repository
In the morning before we start working the team leader gave us the safety brief and work instructions then I started searching for missing mines in section 3 Sabha 8, I removed a 12 and 3 o’clock mines then started working on a 9 o’clock mine I found a squirrel house near the mine I’m working on and found 2 stones on the right and left of the squirrel house, I used the light rake to expose the stones and then used the heavy rake to move the soil and remove the stones I went more than 15 cm depth …
Ddasaccident706, Hd-Aid
Ddasaccident706, Hd-Aid
Global CWD Repository
While the deminer try to recover one missing AP mine (M14) assigned for him by the team leader after grapping all the visible APs in the cluster and the central AT, the mine blasted 2.2 metres away from the deminer while searching the area with the heavy RAKE after pinpointing a signal using the metal detector.
Ddasaccident699, Hd-Aid
Ddasaccident699, Hd-Aid
Global CWD Repository
According to the preliminary investigation the deminer approached to the mine using the proper procedure (15 cm from the side and front), but the depth was less than 15 cm, and the mine was deeply buried (about 18 cm).
Ddasaccident711, Hd-Aid
Ddasaccident711, Hd-Aid
Global CWD Repository
On 27 May 2009 at 0840 hrs [the Victim] the section leader of [Demining group] DT-16 entered to a mined area which was not covered in current MF, stepped on a mine and caused the accident. According to the investigation report the section leader left the site for admin area in order to bring painted rocks for the marking purpose, on the way back from the admin area he wanted to use the shortest way, entered to unsafe area and the accident occurred. He had taken off his PPE and visor. As a result of accident the victim has lost …
Ddasaccident683, Hd-Aid
Ddasaccident683, Hd-Aid
Global CWD Repository
While the deminer try to recover one missing AP mine (M14) assigned for him by the team leader after grabbing all the visible APs in the cluster and the central AT the mine blasted 2.2 metres away from the deminer while searching the area with the heavy RAKE after pinpointing a signal using the metal detector.
Ddasaccident744, Hd-Aid
Ddasaccident744, Hd-Aid
Global CWD Repository
On 11 May 2009 at 09:20 the de-miner [the Victim] was excavating a detected signal in his clearance lane, he stroked the top of a PMN2 mine with his bayonet and the accident happened. As the ground profile is uneven and the accident occurred in an area where the extra soil is brought by seasonal floods and the depth of mine was around 25cm. The deminer failed to go deeper as per procedure and discover the mine properly, so he stroked the mine and caused the accident. According to the investigation report and the pictures of victim deminer the visor …
Ddasaccident748, Hd-Aid
Ddasaccident748, Hd-Aid
Global CWD Repository
On 10 May 2009 at 10:35 [the Victim] the deminer of [Demining group] DT-02 was excavating on a detected signal in his clearance lane where he hit the top of an anti-personnel mine by bayonet and it caused the mine going off. The procedure of investigating a pinpointed signal was ignored by this deminer and he was working carelessly. As a result this accident the deminer got several injuries to different parts of body i.e. both hands and thighs. The deminer had only used the jacket of his PPE without skirt. If he would wear the skirt too, his lower …
Ddasaccident754, Hd-Aid
Ddasaccident754, Hd-Aid
Global CWD Repository
On 07th of May at 10:00 hours the de-miner [the Victim] was working in his clearance lane excavating a detected signal by unsuitable excavation tool (Pick). He hit the top of mine with a pick and caused it to go off. According to the investigation report the signal was not pinpointed correctly and the de-miner has used his pick carelessly. As a result he sustained multiple superficial injuries on his eyes, chest, Face, and both hands, the injured parts of the deminer body and his PPE clearly indicate that he had not used his PPE during operation. Because there is …
Ddasaccident760, Hd-Aid
Ddasaccident760, Hd-Aid
Global CWD Repository
According to the investigation report and as seems from the pictures of scene, the deminer was working with a big shovel. On 19th of April 09 one of the MACCA operations assistant found the team using big shovel and raised a non-conformity report, but the team leader and then the operations officer of [Demining group] did not accept the non-conformity report. However the problem was showed to be solved during the re-audit visits, but in reality it had not been solved and consequently the accident occurred.
Ddasaccident677, Hd-Aid
Ddasaccident677, Hd-Aid
Global CWD Repository
According to the preliminary investigation the incident happened due to individual mistake while the deminer trying to recover an invisible mine and to prevent like incident in the future all invisible Mines would be investigated using the metal detector.