Statistics and Probability Commons^™

Study On Treatment Method Of Expansive Soil Embankment In Expressway Reconstruction And Extension, Wang Yuwei, Hu Yanli, Zhang Rui

Journal of China & Foreign Highway

In order to fully utilize expansive soil as filler in highway reconstruction and expansion projects，this paper draws on the successful experience of using expansive soil directly in road construction.It proposes an embankment treatment scheme that involves the use of geogrid-reinforced expansive soil with edge wrapping，based on the reconstruction and expansion project of the Hefei to Dagudian section of the G 40 Shanghai-Shaanxi Expressway.Through laboratory tests，the road performance and swelling characteristics of the expansive soil filler were investigated to determine the applicable scope and compaction control indices of the filler.Then，the feasibility of the embankment treatment scheme was demonstrated through the prediction …

Prediction Method Of Surrounding Rock Deformation Of Highway Tunnels Based On Bayes‑Lstm, Liu Zhi, Li Xinyu, Li Zhen, Kong Xianguang, Chang Jiantao

Journal of China & Foreign Highway

In the process of highway tunnel construction，the stability of surrounding rock has a great impact on tunnel construction.Therefore，the monitoring measurement and accurate prediction of surrounding rock deformation of highway tunnels are the keys to ensuring the safety of tunnel construction.In view of the low prediction accuracy and poor generalization ability of tunnel surrounding rock deformation，this paper proposed a Bayesian （Bayes ）-based method to optimize the long-term and short-term memory （LSTM ） network.The method first preprocessed the original monitoring data of crown settlement and peripheral convergence，then constructed the initial LSTM model of crown settlement and peripheral convergence of highway tunnels，and used …

Comparative Analysis Of Test Results Of Different Nano‑Clay Improved Loess, Zhao Danni, Cao Baohua, Xu Jiangbo, Nan Yalin, Chen Nengyuan, Zhang Peng, Wang Heping

Journal of China & Foreign Highway

The orthogonal design t est was used to quantitatively analyze the influencing factors and influence degree of compressive strength，shear strength index，and permeability coefficient of improved loess，and the optimal content of improved loess was obtained.In addition，the improvement mechanism of nano-clay materials on loess was explored by scanning electron microscopy.The results show that：① The factors affecting the compressive strength of improved loess are the content of nano-clay，water content，and curing age，and the factors affecting cohesion，internal friction angle，and permeability coefficient are the content，dry density，and confining pressure.② Under different influencing factors，nano-montmorillonite can effectively improve the compressive strength of loess than attapulgite.③ When the material content …

Technical Essentials Of Road Geometric Design In Serbia, Xu Da, Yang Xueyong, Yuan Yingshuang, Chen Dongsheng

Journal of China & Foreign Highway

With the continuous advancement of China's Belt and Road Initiative，more and more Chinese enterprises are participating in the construction of engineering projects in Central and Eastern Europe，which brings some challenges for designers to master and use local codes for engineering design and consultation.According to the concrete practice of road reconstruction design of Hungary-Serbia Railway （Serbia section ），the application of horizontal and vertical indexes in road geometric design in Serbian was summarized.It is found that road design in Serbian has perfect design standards and systems.The Serbian code and the Chinese code are relatively close in terms of road geometric design standards，and …

Effect Evaluation Method Of Foamed Asphalt Based On Digital Image Processing Technology, Chang Xiaoyu

Journal of China & Foreign Highway

In view of the shortage of deter mining the optimal foaming parameters of foamed asphalt only by experience，this paper adopted digital image processing technology to collect images of the mixture of foamed asphalt and milled material RAI obtained under different foaming conditions and carried out grayscale image conversion，morphological processing，binary image conversion，and image segmentation，so as to calculate the asphalt wrapping rate in different areas.With the uniform dispersion of asphalt in the mixture as the indicator，the foaming effect of foamed asphalt was evaluated，and the optimal foaming parameters were determined.The results show that the digital image processing technology can quickly and effectively evaluate …

Research On Construction Risk Of Desert Highway Subgrade Engineering Based On Sem, Wang Shouxu, Han Lingyun

Journal of China & Foreign Highway

Highway construction in desert areas is of great significance to improving the nodes of transportation networks and developing the economy of remote areas.In order to effectively explore the construction risks of desert highway subgrade engineering，the five aspects of personnel risk，technical risk，material risk，mechanical risk，and environmental risk were analyzed，and 23 indicators affecting the construction risk of desert highway subgrade engineering were screened out by literature research method.Based on the effective data collected by questionnaire survey，a structural equation model （SEM ） of the construction risk of desert highway subgrade engineering was constructed，and the key influencing factors of the construction risk were analyzed.The results …

Rut Development Law And Correction Factor Of Axle Load Conversion Of Asphalt Pavement In Long And Large Longitudinal Slope, Guo Chenchen, Ding Tingting, Lyu Xin, Sun Jianxiu, Zhang Jizhe, Yao Zhanyong

Journal of China & Foreign Highway

The existing design specifications do not make special design provisions for pavements in long and large longitudinal slopes，and the directly applied design specifications ignore the stress characteristics of these pavements，which fail to guarantee pavement performance and life.In order to realize the differential design of the pavement structure of special road sections，based on the measured dynamic modulus of asphalt mixture，annual traffic volume，and temperature data，this paper used the self-developed temperature-axle load analysis software to convert the real traffic volume into standard axle load.Abaqus software was used to establish a rut model under the coupling effect of measured axle load and temperature，and the …

Mechanical Behavior Of Composite Structures Of Wearing Course And Underlying Layer For Asphalt Pavements, Yang Xiaohua, Yuan Zhanwen, Wen Yongbing, Zhou Chao, Wu Hao

Journal of China & Foreign Highway

The interlayer bonding state of pavement structures changes due to the influence of various factors under service conditions，and this change exhibits a significant influence on the mechanical behavior of pavement structures.Through the composite structure test and numerical analysis，the mechanical behavior of the composite structure of different wearing courses and underlying layers under different stresses and bonding states was studied.The test used three commonly used wearing course （surface layer ） materials of asphalt pavements，namely AC- 13，OGFC- 13，and SMA- 13 for comparative analysis.The test results show that different composite structures exhibit different interlayer bonding properties and fatigue characteristics due to the difference …

Shear Strength Test Of Hefei Expansive Soil Under Low Stress Conditions With Controlled Suction, Hou Chaoqun, Zhang Rongjian, Li Yongxin

Journal of China & Foreign Highway

Topsoil slide and instability of expansive soil slopes may occur under variable saturation conditions.In order to study the strength characteristics of unsaturated expansive soil under low stress conditions，several different matrix suction and stress conditions were set by unsaturated triaxial apparatus.The triaxial shear test of Hefei expansive soil was carried out，and the test data were analyzed.The test results show that when the net confining stress on the expansive soil continues to weaken，the stress-strain curve transitions from strain hardening to strain softening.The strength of unsaturated expansive soil increases with increasing matrix suction.The shear strength of shallow expansive soil shows a significant reduction …

Influence Of Aerodynamic Shape Change On Wind Resistance Performance Of Large Span Truss Bridge, Jing Dade, Su Yi

Journal of China & Foreign Highway

The development of the transportation an d tourism industry has led to bridges fulfilling additional roles，such as tourism，alongside their transportation functions，resulting in significant changes in structural aerodynamic shape and ventilation rate.This paper analyzed a double-tower single-span steel truss suspension bridge with a main span of 1 088 m，re-evaluated its wind resistance performance through the full-bridge aeroelastic model wind tunnel test，and evaluated the pedestrian comfort problem while studying the wind-resistant stability of the structure.The results indicate that the structural dynamic characteristics of the bridge remain almost unchanged before and after altering the aerodynamic shape of the bridge for its scenic spot …

Influence Of Section Selection On Mechanical Performance Of Corrugated Steel Box Culvert, Zhang Shun, Liu Baodong, Gao Meng, Wu Fei, Wang Zhihong

Journal of China & Foreign Highway

Corrugated steel box culverts exhibit a higher section utilization rate compared with circular，arched，and pipe-arch corrugated steel structures，making them more suitable for for scenarios with restricted embankment height.While numerous studies focus on strengthening strategies for corrugated steel box culverts，research on selecting cross-sectional forms is scarce.This study utilized the finite element analysis software Abaqus to develop finite element models of corrugated steel box culverts with sidewall inclination angles of 0°，5°，10°，15° and 20° respectively.The impact of these inclination angles on the structural stress and deformation outcomes was analyzed.The results indicate that increasing the sidewall inclination angles can effectively reduce vertical deformation and maximum …

Study On Anchorage Reliability For Strand Shoe And Pull Rod Of Air‑Spinning Suspension Bridge, Huang Anming, Yang Bo, Chen Long, Xie Jun, Chen Xin

Journal of China & Foreign Highway

Each strand wire of the main cable in the suspension bridge constructed by the AS method is sleeved and anchored on the strand shoes on both banks.The strand shoe transmits the strand force to the anchoring system through the pull rod.The bearing capacity of the strand shoe after the interaction between the strand shoe and the wires of the main cable，the stress state of the wires after small curvature bending，and the influence of installation accuracy of the pull rod on the anchoring reliability all need to be qualitatively and quantitatively studied and verified by the experiment.In this paper，the main cable …

Research On Gravity Anchorage Foundation Of Dadu River Bridge In Luding, Zhou Ti Ng, Tao Qiyu, Li Zejun

Journal of China & Foreign Highway

Moraine soils formed during th e Qua ternary glacial period are widely distributed in the west of China，exhibiting good mechanical properties and deep overburden.This paper studied the Dadu River bridge in Luding and investigated the influence of various foundation forms on anchorage stability in the case of considering moraine soils as the soil supporting layer of gravity anchorage foundation through theoretical analysis and numerical simulation.The findings suggest that a slant expanded foundation with a notched sill demonstrates good force-bearing capability and is cost-effective.These results can provide a reference for similar construction projects in the west of China.

Test On Water Mist Wrapped Dust Reduction Technology For Tunnels, Wang Yijun, Wang Fei, Jia Yuedi, Pan Weihua, He Xingchun, Yao Wenhui

Journal of China & Foreign Highway

In order to eliminate the dust produced by tunnel blasting more quickly and effectively，two kinds of mist spray and dust reduction schemes were put forward，which were the “air duct water mist wrapped type ” and the “vehicle-mounted water mist wrapped type ”.The field test was carried out on Jiaoding Tunnel in Yunnan.The results show that for the dust reduction technology scheme of “air duct water mist wrapped type ”，the dust concentration of the No.1 characteristic position at the tunnel face decreases to 3.87 mg/m3 after 10 minutes of dust reduction，which meets the specification requirements.For the dust reduction technology of “vehicle-mounted …

Numerical Simulation On Bearing Characteristics Of Tunnel‑Type Anchorage Of A Grand Bridge Over Qingjiang River, Yin Hongmei, Shi Qian, Zhang Yihu

Journal of China & Foreign Highway

This paper took the tunnel-type anchorage on the left bank of a grand bridge over the Qingjiang River as an example and established a three-dimensional geological generalization model based on the engineering geological analysis.In addition，the paper used different software to realize the approximate grid discrete division of complex rock mass and tunnel-type anchorage structure.FLAC3D software was used to simulate different working conditions，and the deformation characteristics and bearing capacity of the tunnel-type anchorage were obtained.It is found that the potential failure mode of the tunnel-type anchorage is that the anchor and the rock mass cut by the structural plane on the …

Study On Length Of Deceleration Lane Of Left Off‑Ramp For Urban Underground Interchanges Based On Traffic Conflicts, Wang Hailiang, Cheng Chong, Guan Hong, Ding Naikan

Journal of China & Foreign Highway

To set a reasonable range of the length of the deceleration lane in the diverge area of the left off-ramp for urban underground interchanges，the effects of the length of the deceleration lane，as well as interactions between traffic volumes and design speeds of mainline and ramp on traffic conflict in the diverge area，were exami ned.By taking the underground interchange of the Wuhan East-South Lakes Tunnel Project as an example，the VISSIM micro traffic simulation test was carried out，and the conflict rate （RCR） and exposed time to collision （TTET） were extracted.The results show that ① when the length of the deceleration lane increases，the …

Study On Safety Risk Assessment System For Waste Dump Of Mountainous Expressways, Ye Xian, Yin Hao, Zhao Xin, Wang Guanqun, Gao Yu

Journal of China & Foreign Highway

The safety of waste dump projects of mountainous expressways is related to environmental protection，water and soil conservation，highway building protection，and downstream environment-sensitive point protection，so it is necessary to put forward safety assessment methods.Based on the data analysis of 1 369 waste dumps in Yunnan Province，the safety risk factors of the waste dump engineering were proposed and summarized as five primary indicators，including site selection and design factors，construction factors，regional geological factors，external influencing factors，and data integrity factors，and 18 secondary indicators were further put forward.The group decision-making analytic hierarchy process （AHP ） model was established，and the weight of secondary indexes was determined by 64 technical …

Analysis On Design Concept Of Subgrade And Pavement Of Colombia High‑Grade Highway, Liu Tao, Hu Guanhua, Yuan Yi

Journal of China & Foreign Highway

Colombian highway design predominantly adheres to American Standards，emphasizing design concepts reflective of the United States while encompassing Colombia's engineering design habits，concepts，and characteristics.This paper introduced the main design schemes of the Colombia MAR 2 Highway Project in northern Colombia，including protection engineering，drainage engineering，subgrade filling，spoil ground，and pavement.It conducted a comparative analysis between Colombian and Chinese design concepts，highlighting similarities and disparities，and put forward the thinking of mutual learning.

Study On Flexural Behavior Of Wet Joints Of Prefabricated Steel‑Uhpc Composite Bridge Deck, Liao Wancheng, Zhao Hua, An Jiahe

Journal of China & Foreign Highway

Prefabricated steel-UHPC composite bridge deck is a new deck structure system that places the longitudinal rib at the upper layer and forms PBL shear connectors.This structure can be prefabricated in the factory and assembled on-site.The adjacent steel beams are integrated by welding，and the cast in-situ UHPC wet joints connect the adjacent UHPC bridge decks.However，these wet joints represent the structure's vulnerable segments but with little research.To this end，a full-scale model test has been conducted to study the flexural behavior of the wet joints in a steel-UHPC composite bridge deck in a practical project.The Abaqus finite element model was established and verified …

Research On Shape Optimization Of Four‑Center Circular Highway Tunnel Based On Parametric Modeling Idea, Zhu Lei, Guo Meng, Guo Jinyong, Shen Caihua, Zhang Hanyi

Journal of China & Foreign Highway

The rational cross-sectional form of the four-center circular highway tunnel contributes to enhancing the stress state of the lining structure，reducing cracks in the composite lining，and enhancing the durability of the tunnel structure.Utilizing the Ansys APDL programming platform and guided by the design principle of continuous-curvature，a parametric modeling equation for the geometrical dimensions of local tunnel shape in arch foot area was established.The calculation method and numerical simulation models for the equivalent mechanical parameters of the anchor reinforcement area were also developed.The study revealed the impact of the local tunnel shape parameter design in the arch foot area on the internal …

An Analysis Of China’S Perceived Geographic Locations Of Interest By Use Of Value Informed Facility Location Models, Layton C. Hedge

Theses and Dissertations

This research examines China and derives insights specific to it and the First Island Chain and the Second Island Chain. In doing so, this research demonstrates a methodology to examine other competitors and their geostrategic interests. In the first phase of analysis, it develops a value hierarchy to depict objectives within subregions of the area of interest and considers four alternative weightings of the value hierarchy. In the second phase of analysis, it applies four location-covering models to assess how the competitor would emplace a range of limited resources to deter and/or control points of interest. Results indicate that land-based …

Examining The Effect Of Contractor Logistics Support On The Reliability Of Military Aircraft, Rodrigo S. Campos De Moura

Theses and Dissertations

This study utilizes survival analysis for examining the effect of Contractor Logistics Support (CLS) on the reliability of military aircraft before and after implementing CLS. The provider of CLS in this study is the original equipment manufacturer that designed and produced the target aircraft of this study, the Embraer A-29 Super Tucano.

Simulating Human-Autonomous Aircraft Teams In An Anti-Access Area Denial (A2ad) Environment, Michael Kaminski

Theses and Dissertations

The role of autonomy has evolved recently, demanding tighter integration between human and autonomous systems, particularly in highly contested A2AD environments. Near-peer adversaries have modernized their integrated air defense systems (IADS), diminishing the current advantages of the United States Air Force. To regain air dominance, efforts like the Collaborative Combat Aircraft (CCA) program are underway, aiming to deploy unmanned autonomous alongside manned next-generation fighter aircraft. This research assesses various operational concepts, focusing on autonomous tactics post-manned fighter loss, strike timing of independent teams, and weapon configuration observability. Using the Advanced Framework for Simulation, Integration and Modeling (AFSIM), an agent-based model …

Dice Are Blessed Or Cursed, Warren Campbell, Cameron Miller

SEAS Faculty Publications

Dice are cursed or blessed; that is, they roll low or high, but they are never fair. They cannot be manufactured with uniform density and geometric precision. This is particularly true of 20-sided dice or D20s. Faces are smaller than 6-sided dice, and manufacturing tolerances are similar. However, some dice are fairer than others. In our studies of plastic-mold dice about 1 in 4 test fair in 3000 rolls. We have used different statistical tests, including chi-square, modified Kolmogorov Smirnov, and double binomial tests. Of these, the method that consistently performed better is the chi-square goodness of fit test. The …

A 3-Step, Open-Data, Ride-Hailing Ridership Model With Pricing Applications, Richard A. Mucci

Theses and Dissertations--Civil Engineering

Researchers and practitioners studied the effects ride-hailing had in cities before the covid-19 pandemic. Previous research found ride-hailing to produce negative externalities, such as reducing transit ridership and increasing congestion in various cities. Since the pandemic, ride-hailing ridership has nearly recovered to pre-pandemic levels in Chicago. Ride-hailing ridership has grown steadily since the pandemic while a rider’s willingness to share their trip stagnated. Ride-hailing ridership nearly recovering to pre-covid levels in Chicago suggests that transportation planners, and policy makers, will need to continue assessing the impacts ride-hailing trips have in their cities.

Pickup and drop off locations in the Chicago …

L∞ Bounds For Transient Growth In Repetitive And Iterative Learning Control Systems, Douglas A. Bristow, John R. Singler

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper revisits the problem of large transient growth in Iterative Learning Control (ILC) and Repetitive Process Control (RPC) systems. In ILC and RPC problems a process is repeated iteratively, with new control calculations occurring in between each iteration. Large transient growth refers to the propensity of some control algorithms to grow error exponentially before eventually converging. While robust monotonic convergence algorithms (in which monotonic convergence is guaranteed usually in exchange for a small loss in performance) have largely eliminated the concern for large transient growth in ILC, similar results cannot always be obtained in RPC. The emergence of additive …

Developing Machine Learning And Time-Series Analysis Methods With Applications In Diverse Fields, Muhammed Aljifri

Theses and Dissertations

This dissertation introduces methodologies that combine machine learning models with time-series analysis to tackle data analysis challenges in varied fields. The first study enhances the traditional cumulative sum control charts with machine learning models to leverage their predictive power for better detection of process shifts, applying this advanced control chart to monitor hospital readmission rates. The second project develops multi-layer models for predicting chemical concentrations from ultraviolet-visible spectroscopy data, specifically addressing the challenge of analyzing chemicals with a wide range of concentrations. The third study presents a new method for detecting multiple changepoints in autocorrelated ordinal time series, using the …

Multiple Imputation For Robust Cluster Analysis To Address Missingness In Medical Data, Arnold Harder, Gayla R. Olbricht, Godwin Ekuma, Daniel B. Hier, Tayo Obafemi-Ajayi

Mathematics and Statistics Faculty Research & Creative Works

Cluster Analysis Has Been Applied To A Wide Range Of Problems As An Exploratory Tool To Enhance Knowledge Discovery. Clustering Aids Disease Subtyping, I.e. Identifying Homogeneous Patient Subgroups, In Medical Data. Missing Data Is A Common Problem In Medical Research And Could Bias Clustering Results If Not Properly Handled. Yet, Multiple Imputation Has Been Under-Utilized To Address Missingness, When Clustering Medical Data. Its Limited Integration In Clustering Of Medical Data, Despite The Known Advantages And Benefits Of Multiple Imputation, Could Be Attributed To Many Factors. This Includes Methodological Complexity, Difficulties In Pooling Results To Obtain A Consensus Clustering, Uncertainty Regarding …

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

College of Graduate Studies: Theses & Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Investigation Of The Effect Of Preparation Parameters On The Structural And Mechanical Properties Of Gelatin/Elastin/Sodium Hyaluronate Scaffolds Fabricated By The Combined Foaming And Freeze-Drying Techniques, Mansour Qamash, S. Misagh Imani, Meisam Omidi, Ciara Glancy, Lobat Tayebi

Electrical & Computer Engineering Faculty Publications

This paper aimed to evaluate the effects of different preparation parameters, including agitation speed, agitation time, and chilling temperature, on the structural and mechanical properties of a novel gelatin/elastin/sodium hyaluronate tissue engineering scaffold, recently developed by our research group. Fabricated using a combination of foaming and freeze-drying techniques, the scaffolds were assessed to understand how these parameters influence their morphology, internal microstructure, porosity, mechanical properties, and degradation behavior. The fabrication process used in this study involved preparing a homogeneous aqueous solution containing 8% gelatin, 2% elastin, and 0.5% sodium hyaluronate (w/v), which was then subjected to mechanical agitation at speeds …