Statistical, Nonlinear, and Soft Matter Physics Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Techno-Enviro-Economic Analysis Of Precipitated Calcium Carbonate Production From Carbon Dioxide In Cement Industry Flue Gas And Calcium Hydroxide, Natalia Debora Panggabean, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

CCUS is a technological solution to reduce emissions from the cement industry, which is the second largest CO2-intensive industry. This study aims to analyze technical, economic, and environmental performance of Precipitated Calcium Carbonate (PCC) synthesis in cement industry flue gas. The process simulation includes the CO2 capture system from cement plant, CO2 captured used as feedstock for PCC synthesis process through its reaction with calcium hydroxide. The simulation was carried out using ASPEN Plus software. Technical analysis was performed to determine the CO2 capture efficiency and PCC synthesis efficiency. Economic analysis was conducted to calculate CO2 capture cost and production …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Markov-Modulated Queueing Network For Mobile Traffic Aggregation With Threshold-Controlled Buffers, Anton A. Esin, Elmira Yu. Kalimulina

Mathematical Modelling and Numerical Simulation with Applications

We study the problem of data transmission from mobile platforms operating in high-speed transit between cellular base stations, under conditions of unstable and intermittent connectivity. Conventional queueing and connectivity models often fail to capture the combined effects of rapidly changing signal conditions, finite buffer capacity, and dynamic topology. We aim to develop a tractable yet expressive model that integrates stochastic link availability, queue dynamics, and buffer control. We propose a mathematical framework based on queues whose service intensities are modulated by a continuous-time Markov chain (CTMC) representing signal conditions along a high-speed trajectory. The core subsystem is a two-stage (aggregation …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

Modeling Synaptic Dysfunction As Neural Contagion: A Graph-Based Sedr Framework For Simulating Signal Spread, Michelle Marfo, Dr. Padmanabhan Seshaiyer, Alonso Ogueda-Oliva

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Phase Nanoscopy With Correlated Frequency Combs, Xiaobing Zhu

Optical Science and Engineering ETDs

In this dissertation a sensing method applying to any physical quantity that modifies optical phase is developed. Two pulses are produced inside a synchronously pumped Optical Parametric Oscillator, generating two identical, undistinguishable frequency combs. The physical quantity to be measured applies a small phase shift/round trip to one of the pulses, resulting in a frequency shift of the corresponding comb. The latter frequency is measured as a beat by interfering the two combs on a detector. A world record resolution, close to the quantum limit, of 0.033 nanoradian (corresponding to 0.006 fm in displacement) is achieved. A detailed analysis of …

Theoretical And Experimental Investigation Of Liquid-Liquid Phase Separation: Characterizing Elastin-Like-Polypeptides, Adam D. Quintana

Chemical and Biological Engineering ETDs

This dissertation develops and validates a semi-empirical Flory–Huggins-based interaction model, combined with Cahn–Hilliard simulations, for predicting multi-component liquid–liquid phase separation (LLPS) in elastin-like polypeptide (ELP) systems. Equilibrium droplet compositions, measured using a PDMS-based microfluidic device, enabled direct parameterization of interaction coefficients. The model was applied to generate phase diagrams and assess composition dependence in ternary mixtures. Cahn–Hilliard simulations were conducted to explore potential phase morphologies under different interfacial conditions. Multi-component Lattice Boltzmann simulations were implemented to model droplet morphology evolution under varying interfacial and diffusive parameters, reproducing experimentally relevant morphologies. A three-phase wetting study revealed conditions for selective wetting and …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Robust Spacecraft Autonomy For Deep Space Exploration In Special Euclidean Group Se(3), Matthew Wittal

Doctoral Dissertations and Master's Theses

Over the past half-century, humanity has gained extensive experience conducting manned spaceflight near Earth. Arguably, "near Earth" could even include the Moon — the most distant destination humans have reached. However, "near" in this work primarily refers low Earth orbit (LEO). One could argue that we have not truly left Earth since the Apollo, as spacecraft in some LEOs remain subject to atmospheric drag thus emphasizing their continued connection to Earth's immediate environment. Reflecting on this, it becomes clear that humanity has largely remained bound to Earth’s immediate vicinity since the Apollo missions reached the Moon. However, that is set …

A Comparative Study Of Conventional And Statistically Active Corrosion Methods For Corrosion Growth Assessment Of A 24-Inch Gas Pipeline, Rudi Rinaldi, Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

Component failures in oil and gas pipelines can have fatal consequences, leading to operational downtimes and environmental damage. Knowledge of the corrosion growth rate is fundamental to pipeline integrity management, as it is essential for risk assessment and decisions related to asset management. This article aimed to compare two approaches for the corrosion growth estimation of the 24-inch offshore gas pipeline: the conventional method versus the Statistically Active Corrosion (SAC) method. This article is based on the in-line inspection (ILI) results of two consecutive assessments from 2020 to 2023 of the entire 73 km of the pipeline. The results show …

Smart Automatic Modal Hammer Predictor–Corrector Approach For Accurate Excitation Of Dynamical Systems, Mohammad Nasr

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This research introduces an innovative solution that revolutionizes the study of linear and nonlinear dynamical systems—a smart automatic modal hammer. With its affordability and intelligent capabilities, this automatic modal hammer becomes an invaluable tool for research and industry, enabling repeatable strikes with precise force control. This system's significance becomes particularly evident when studying nonlinear systems, which heavily rely on the excitation level for their dynamics. By offering a cost-effective design this proposed system proves to be robust in accelerating research on nonlinear dynamics, providing researchers with an efficient and accessible means to delve deeper into these complex systems. The proposed …

Mesostructure Reconstruction Of Prepreg Platelet Molded Composite With Artificial Intelligence, Richard Larson

Mechanical & Aerospace Engineering Theses & Dissertations

Prepreg platelet molded composites (PPMC) are long, discontinuous fiber reinforced polymer materials. PPMC are an important subcategory of composite materials as they are processible into geometrically complex structures and can be produced via high-throughput manufacturing processes, however they have higher stiffness and strength as compared to traditional discontinuous fiber reinforced polymers. However, there is inherent randomness in the structure of PPMCs and as such, PPMC parts frequently require per part testing that is cost prohibitive.

Herein, a method using artificial intelligence is proposed as a more cost-effective method of inspecting PPMC parts. Different artificial intelligence (AI) architectures are explored to …

Information Theoretic Bounds For Capacity And Bayesian Risk, Ian Zieder

Dissertations

In this dissertation, the problem of finding lower error bounds on the minimum mean-squared error (MMSE) and the maximum capacity achieving distribution for a specific channel is addressed. Presented are two parts, a new lower bound on the MMSE and upper and lower bounds on the capacity achieving distribution for a Binomial noise channel. The new lower bound on the MMSE is achieved via use of the Poincare inequality. It is compared to the performance of the well known Ziv-Zakai error bound. The second part considers a binomial noise channel and is concerned with the properties of the capacity-achieving distribution. …

Integration Of The Ashby Technique And Pahl-Beitz Quantitative Ranking For Railway Axle Material Selection, Helya Chafshoh Nafisah, Jaka Fajar Fatriansyah, Siti Norasmah Surip

Journal of Materials Exploration and Findings

Railway axle serves as a vital connection between the train's wheels and its body. However, cyclic loading and high speed can induce fatigue in railway axle, which potentially leads to damage human safety. Therefore, it is important to find materials that have good mechanical properties with the lowest weight and cost. In this paper, a comprehensive method using Ashby chart has been performed to select candidate materials of railway axle. The methods begin with analyzing function by determining the problem, objective function, and constraints. After that, the results obtained are ranked using Pahl and Beitz quantitative weighting method. The results …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Investigation Of Domain Formation During Phase Separation In A Mixture Of Flexible And Rigid Biopolymers, Steven Huntley

All Theses

Complex fluids and heterogenous mixtures composed of multiple types of polymers are found throughout industrial and biological fluid systems. For example, extrusion based additive manufacturing systems pass dense mixtures of polymers through the extrusion heads to deposit composite polymeric materials. In cells, active and complex mixtures of biopolymers self-organize into assemblies that perform critical physiological functions.

Polymers in dense solutions undergo phase separation as a result of differences in physiochemical properties. A few examples of these properties include charge, structure, rigidity, and hydrophobicity. We observe the formation of polymer domains composed of rigid and a flexible biopolymer species that phase …

Application Of The Fokker-Planck Equation For Quantifying Initial Condition Uncertainty Of Reversible Dynamic Systems, Troy S. Newhart

Mechanical & Aerospace Engineering Theses & Dissertations

Characterizing the behavior of dynamic systems requires the inclusion of initial conditions to propagate behavior forward in time. More realistic representations of system behavior quantify uncertainty about the initial conditions to assess sensitivity, reliability, and other stochastic response parameters. In many engineering applications, the uncertain initial conditions may be unknown given a desired response. This research applies the Fokker-Planck equation to reversible dynamic systems of select multi-dimensional nonlinear differential equations as a means for predicting the uncertainty about initial conditions. An alternating directions implicit numerical scheme is used to numerically solve the Fokker-Planck equation for both forward and reversed equations …

Hydrodynamics Of Drops And Particles Driven By Marangoni And Diffusiophoretic Forces, Subramaniam Chembai Ganesh

Dissertations and Theses

This study investigates the hydrodynamics of particles and drops driven by forces generated by an asymmetrical physical and chemical surrounding environment. In the first part, a novel colloidal motor design driven by surface tension forces is proposed, utilizing an active Janus particle encapsulated in an immiscible liquid drop to form a compound drop/particle. Marangoni forces induced by asymmetric solute adsorption at the liquid-liquid interface of the drop propels the compound system. The propulsion speeds of the motor are analyzed for various relative sizes and configurations of the Janus particle and the encapsulating drop and the effects of varying the transport …