Engineering Physics Commons^™

Fuel Flow Reduction Impact Analysis Of Drag Reducing Film Applied To Aircraft Wings, Damon Resnick, Chris Donlan, Nimish Sakalle, Cody Pinkerman

SMU Data Science Review

In this paper, we present an analysis of flight data in order to determine whether the application of the Edge Aerodynamix Conformal Vortex Generator (CVG), applied to the wings of aircraft, reduces fuel flow during cruising conditions of flight. The CVG is a special treatment and film applied to the wings of an aircraft to protect the wings and reduce the non-laminar flow of air around the wings during flight. It is thought that by reducing the non-laminar flow or vortices around and directly behind the wings that an aircraft will move more smoothly through the air and provide a …

The Drag Coefficient Of Varying Dimple Patterns, James M. Seeley, Michael S. Crosser

Senior Theses

There are many golf balls on the market today with varying dimple sizes, shapes, and distribution. These proprietary differences are all designed to reduce drag on the balls during flight, allowing golfers to hit the ball farther distances. There are limited published studies comparing how varying the dimples affects the reduction of drag. An experiment was developed in which golf balls were pulled through a water tank to measure the drag force acting on each ball. The water was chosen to allow for testing at slower velocities than the typical necessary speeds to cause turbulence for balls traveling in air. …

Numerical Simulation Of A High Strain Rate Biaxial Compression Apparatus, Michael Lagieski

McKelvey School of Engineering Graduate Student Theses & Dissertations

Few experimental methods today are capable of exploring the strength of materials at high strain rates (10⁵ s^-1). Those that are capable, such as the Split Hopkinson Bar, Taylor Anvil and Plate Impact suffer from instability and are generally limited to one dimensional wave propagation. Of particular interest is material response under biaxial compression, similar to that seen in inertial confinement fusion. Laser fusion fuel pellets typically undergo large strain rates as well as plastic deformation and non-linear behavior. This work briefly outlines an experimental procedure designed to replicate these large strain rates under biaxial compression using …

University Of Minnesota Smallsat And High Altitude Ballooning Development And Collaboration, Luke Zumwalt, Ricardo Saborio, Athanasios Pantazides, Aaron Nightingale, Demoz Gebre Egziabher, Lindsay Glesener

2017 Academic High Altitude Conference

The Experiment for X-ray Characterization and Timing (EXACT) mission is a 3U CubeSat technology-development project being built by the SmallSat team at the University of MN – Twin Cities which is a joint research effort of the Aerospace Engineering and Mechanics (AEM) Department and the School of Physics and Astronomy (SPA). The main objective of this spacecraft is to carry a payload including a detector designed to measure energy and time of arrival time of individual hard x-ray photons emitted from the Sun and from other astrophysical sources. During the development process for EXACT, flights provided by the High-Altitude Student …

An Enhanced Operational Definition Of Dielectric Breakdown For Dc Voltage Step-Up Tests, Allen Andersen, Jr Dennison

Journal Articles

The imprecise definition of breakdown in the ASTM D3755-14 standard can misidentify breakdown. If the recommended test circuit current sensing element threshold is set too high, breakdown may occur undetected. Conversely, false positives may result from designating a low current threshold. An operational definition of breakdown much less sensitive to these pitfalls is outlined herein. This enhanced definition of breakdown is based on the average rate of change of the leakage current with increasing voltage, rather than a simple current threshold, avoiding ambiguous association with anomalies in current traces. For tests that continuously monitor leakage current, breakdown can be detected …

Variable Structure Feedback Control With Application To Spacecraft With Small Thrust Propulsion Systems, Samuel J. Kitchen-Mckinley

Doctoral Dissertations and Master's Theses

Small spacecrafts requiring small propulsion systems are becoming more popular for low Earth orbit. It is important for these research satellites to have accurate guidance and control systems. Small propulsion systems will also be beneficial for multiple small spacecrafts used future exploration expeditions beyond low Earth orbit. These small spacecrafts benefit from the simplicity of low thrust cold gas propulsion systems. Additionally, large spacecrafts using low thrust, high specific impulse propellants for main propulsion systems, such as ion engines, allow longer and more flexible missions, including Earth orbiting spacecraft and interplanetary spacecraft.

In order to extend the life of future …

Nonlinear Control Of A Thermoacoustic System With Multiple Heat Sources And Actuators, Mikael O. Molina Sandoval

Doctoral Dissertations and Master's Theses

Thermoacoustic instabilities can occur in thermal devices when unsteady heat release is coupled with pressure perturbations. This effect results in excitation of Eigen-acoustic modes of the system. These instabilities can lead to unpredictable behavior of the system. Gas-turbine combustion systems are especially prone to this phenomenon reducing their overall efficiency. Additionally, due to the nature of the combustion, the turbines end up releasing undesired amounts of harmful chemicals to the atmosphere, such as Nitrous Oxide (NOX).

A Rijke tube, representing a resonator with a mean flow and a concentrated heat source, is a convenient system to study the thermoacoustic phenomena. …

Early Afternoon Concurrent Panel Sessions: Commercial Space Industry Snapshot: Presentation: Small Catapult-Assisted Horizontal-Launch Reusable Rbcc Ssto Spaceplane For Economical Short-Duration Leo Access, Nihad E. Daidzic,

Aviation / Aeronautics / Aerospace International Research Conference

This article discusses the conceptual design, flight trajectory calculations, and utilization of the possible future horizontally-launched reusable Single-Stage-to-Orbit (SSTO) spaceplane for small payload short-duration manned/unmanned access to Low-Earth-Orbit (LEO). The 10,000 lb spaceplane would use 5,000 ft catapult-assist horizontal-launch facility and conduct powered approach and landing on conventional horizontal paved runways following the gliding atmospheric re-entry. To increase the economy of operation, the launch facility located at high elevations (4,000+ ft) equatorial region is required, such as, the plateaus in Kenya and Tanzania in Africa and/or Ecuador in South America. A 500-lb payload, including pilot-commander, is envisioned. The propulsion cycle …

Determination Of Rejected Landing Roll Runway Point-Of-No-Return And Go-Around In Transport Category Airplanes, Nihad E. Daidzic, Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

The decelerate-accelerate-takeoff maneuver in transport category airplanes has been discussed. Mathematical model based on total energy conservation has been used to calculate the rejected landing point-of-no-return on a runway which will still enable the airplane to safely execute go-around and achieve regulatory screen heights and takeoff safety speeds. After this point has been exceeded or below the point-of-no-return speed no go-around should ever be considered. Landing long and fast and/or decelerating on slippery runways may very well result in an overrun which could be prevented if the go-around is attempted before reaching this critical runway point. The point-of-no-return on the …

Project Low Horizon - Horizon Detection Through The Use Of Infrared Sensors, Adam Bower, Evan Unruh, Justin Smith

Von Braun Symposium Student Posters

No abstract provided.

Global Optimized Isothermal And Nonlinear Models Of Earth’S Standard Atmosphere, Nihad E. Daidzic, Ph.D.,

International Journal of Aviation, Aeronautics, and Aerospace

Both, a global isothermal temperature model and a nonlinear quadratic temperature model of the ISA was developed and presented here. Constrained optimization techniques in conjunction with the least-square-root approximations were used to design best-fit isothermal models for ISA pressure and density changes up to 47 geopotential km for NLPAM, and 86 orthometric km for ISOAM respectively. The mass of the dry atmosphere and the relevant fractional-mass scale heights have been computed utilizing the very accurate eight-point Gauss-Legendre numerical quadrature for both ISOAM and NLPAM. Both, the ISOAM and the NLPAM represent viable alternatives to ISA in many practical applications and …

The Robert & Esther Goddard Papers, Robert H. Goddard

Finding Aids

Dr. Robert H. Goddard was a member of the Clark Physics Department for 29 years. Foremost American pioneer of rocket research, he laid the technical and theoretical foundations for many of the developments in long-range rockets, missiles, satellites and space flight, which collectively put us into the Space Age.

The collection includes correspondence, diaries, journals, patent applications and awards, reports, and photographs. The collection also includes original paintings by Dr. Goddard.

Efficient General Computational Method For Estimation Of Standard Atmosphere Parameters, Nihad E. Daidzic Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

Knowledge of standard air temperature, pressure, density, speed of sound, and viscosity as a function of altitude is essential information in aircraft design, performance testing, pressure altimeter calibration, and several other aeronautical engineering and aviation science applications. A new efficient computational method for rapid calculations of standard atmospheric parameters up to 86 orthometric km is presented. Additionally, mass and weight of each standard atmospheric layer were calculated using a numerical integration method. The sum of all fractional masses and weights represents the total mass and weight of Earth’s atmosphere. The results obtained here agree well with measurements and models of …

A Contribution Toward Better Understanding Of Overbanking Tendency In Fixed-Wing Aircraft, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

The phenomenon of overbanking tendency for a rigid-body, fixed-wing aircraft is investigated. Overbanking tendency is defined as a spontaneous, unbalanced rolling moment that keeps increasing an airplane’s bank angle in steep turns and must be arrested by opposite aileron action. As stated by the Federal Aviation Administration, the overbanking tendency may lead to a loss of control, especially in instrument meteorological conditions. It was found in this study that the speed differential over wing halves in horizontal turns indeed creates a rolling moment that achieves maximum values for bank angles between 45 and 55 degrees. However, this induced rolling moment …

Lightweight Uav Launcher, Ben Miller, Christian Valoria, Corinne Warnock, Jake Coutlee

Mechanical Engineering

This report discusses the design, construction, and testing of a lightweight, portable UAV launcher. There is a current need for a small team of soldiers to launch a US Marine Tier II UAV in a remote location without transport. Research was conducted into existing UAV launcher designs and the pros and cons of each were recorded. This research served as a basis for concept generation during the initial design development stage. It was required that the design weigh less than 110 lbs, occupy a smaller volume than 48" x 24" 18" in its collapsed state, be portable by a single …

Evolution Of Perturbations In Flow Field Mechanics, Samantha R. Bell, David Forliti, Nils Sedano, Kriss Vanderhyde

STAR Program Research Presentations

This project explores the stability analysis of a given flow field. Specifically, where the peak disturbance occurs in a flow as this is the disturbance that is most likely to occur. In rocket combustion, it is important to understand where the maximum disturbance occurs so that the mixing of fuel can be stabilized. The instabilities are the results of frequencies in the area surrounding the flow field. The linear stability governing equations are employed to better understand the disturbance. The governing equations for continuity and momentum in the x and y directions are used to form an equation for the …

Robust And Adaptive Nonlinear Control Of Limit Cycle Oscillations In Uavs Using Synthetic Jet Actuators, Natalie Ramos Pedroza

Doctoral Dissertations and Master's Theses

Limit cycle oscillations (LCO), also known as utter, cause significant challenges in fight control of unmanned aerial vehicles (UAVs), and could potentially lead to structural damage and catastrophic failures. LCO can be described as vibrational motions in the pitching and plunging displacements of an aircraft wing. Even in low Reynolds number (low-Re) fight regimes, LCO can exceed the limiting boundary for safe UAV fight. Further, as practical considerations motivate the design of smaller, lighter weight UAVs, there is a growing need for UAV systems that do not require heavy mechanical actuators (e.g., ailerons). To address this, the use of synthetic …

Robust Control Methods For Nonlinear Systems With Uncertain Dynamics And Unknown Control Direction, Chau T. Ton

Doctoral Dissertations and Master's Theses

Robust nonlinear control design strategies using sliding mode control (SMC) and integral SMC (ISMC) are developed, which are capable of achieving reliable and accurate tracking control for systems containing dynamic uncertainty, unmodeled disturbances, and actuator anomalies that result in an unknown and time-varying control direction. In order to ease readability of this dissertation, detailed explanations of the relevant mathematical tools is provided, including stability denitions, Lyapunov-based stability analysis methods, SMC and ISMC fundamentals, and other basic nonlinear control tools. The contributions of the dissertation are three novel control algorithms for three different classes of nonlinear systems: single-input multiple output (SIMO) …

Nonlinear Control For Dual Quaternion Systems, William D. Price

Doctoral Dissertations and Master's Theses

The motion of rigid bodies includes three degrees of freedom (DOF) for rotation, generally referred to as roll, pitch and yaw, and 3 DOF for translation, generally described as motion along the x, y and z axis, for a total of 6 DOF. Many complex mechanical systems exhibit this type of motion, with constraints, such as complex humanoid robotic systems, multiple ground vehicles, unmanned aerial vehicles (UAVs), multiple spacecraft vehicles, and even quantum mechanical systems. These motions historically have been analyzed independently, with separate control algorithms being developed for rotation and translation. The goal of this research is to study …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Investigation Of Magnetic Field Profile Effects In Hall Thrusters, Oren Kornberg

Master's Theses - Daytona Beach

The purpose of this study was to show the relationship of different magnetic field profiles to the acceleration region length of a Hall thruster. The general transport equations were simplified and solved using a one-dimensional analysis. Some of the model assumptions include quasineutrality, Maxwellian electrons, and negligible thruster wall effects. The solved equation kept magnetic field as an input to the model for the analysis. The magnetic field was altered by changing the shape through the thruster, while keeping the maximum point fixed, and by shifting the profile, while keeping the shape fixed. Results indicate a strong correlation between the …

Advances In Space Radiation Shielding Codes, John W. Wilson, Ram K. Tripathi, Garry D. Qualls, Francis A. Cucinotta, Richard E. Prael, John W. Norbury, John H. Heinbockel, John Tweed, Giovanni De Angelis

Mathematics & Statistics Faculty Publications

Early space radiation shield code development relied on Monte Carlo methods and made important contributions to the space program. Monte Carlo methods have resorted to restricted one-dimensional problems leading to imperfect representation of appropriate boundary conditions. Even so, intensive computational requirements resulted and shield evaluation was made near the end of the design process. Resolving shielding issues usually had a negative impact on the design. Improved spacecraft shield design requires early entry of radiation constraints into the design process to maximize performance and minimize costs. As a result, we have been investigating high-speed computational procedures to allow shield analysis from …

An Erasable Optical Memory Based On Stimulated Electronic Transition Concept, James D. Satira

Electrical & Computer Engineering Theses & Dissertations

Erasable optical memory systems with a high storage density and a large data transfer rate are required for many real time data acquisition systems such as those placed aboard NASA's space born platforms. A new concept for erasable optical memory involving stimulated electronic transitions (SET) will meet these requirements. The SET concept useful in erasable optical storage systems was demonstrated in MgS and SrS doped with Eu and Sm. The optical properties of these materials were studied. The reading and writing wavelengths for these samples were determined to be 950 and 514 nm respectively. The peaks of the emission spectra …

Static Temperature Measurements In Supersonic Flow Using Lasar Raman Spectroscopy, Paul A. Nystrom

Mechanical & Aerospace Engineering Theses & Dissertations

Laser Raman spectroscopy is a nonintrusive technique which can generate mean static temperature (MST) data within flow fields. By ratioing two simultaneously gathered portions of the Raman scattered spectrum, absolute intensity measurements were not needed. This method was applied to a supersonic cold air jet, where the NST ranged from 160'K to 300'K. Accurate measurements were not realized due to the presence of flow contaminates, especially water vapor.