Physics Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Website: Home, Zhiqu Lu, Likun Zhang, Lei Cao

Gulf Research Program Data Sets

No abstract provided.

Website: Latest Results, Zhiqu Lu, Likun Zhang, Lei Cao

Gulf Research Program Data Sets

No abstract provided.

Website: News And Events, Zhiqu Lu, Likun Zhang, Lei Cao

Gulf Research Program Data Sets

No abstract provided.

A Feedback Loop Control To Automate Cold Atmospheric Pressure Plasma Based Additive Manufacturing, Arineh Shahbazi

Discovery Day - Daytona Beach

Currently, nanoparticle annealing based additive manufacturing process requires high temperatures, making them unsuitable for a broad range of applications. By lowering the temperature and developing a process to use Cold Atmospheric Pressure Plasma (CAPP) for annealing, many more doors are opened to a wide range of materials, films, and environments for space, communication, and microelectronics. CAPP-based additive manufacturing technology is continually evolving, making projects like nanoparticle annealing more feasible. In this work, we designed a CAPP jet printer assembly consisting of a 0.25-inch outer diameter glass tube connected to a 3D printing nozzle. The flow of Argon gas in the …

Emergent De Sitter Expansion And Closed Topology From The Cosmic Fabric Model As An Open Thermodynamic System: Resolving The Negative Bulk Modulus Paradox, T G. Tenev, C B. Ward, T F. Tenev, M F. Horstemeyer

Faculty Publications and Presentations

The Cosmic Fabric Model establishes a continuum-mechanics isomorphism to General Relativity by representing physical space as an elastic three-dimensional hyperplate embedded in a four-dimensional spatial bulk. Reproducing vacuum kinematics requires a vanishing P-wave modulus, which in turn implies a negative bulk modulus—an apparent thermodynamic instability in a closed system. This paradox is resolved by recasting the framework as an open system: the instability is not pathological but instead drives cosmic expansion. In this interpretation, the observable universe is a lower-energy solid formed through continuous solidification from a higher-dimensional precursor fluid. Using multiplicative kinematics from finite-growth mechanics, the model shows that …

Global Time-Resolved Measurements Of Inlet/Isolator Unstart Induced By Mass Injection, Andrew N. Bustard, Benjamin L. Bemis, Aaron Marques, Matthew J. Zahr, Thomas J. Juliano

Publications

The inner surface pressure of an axisymmetric inlet/isolator model was measured using anodized-aluminum pressure-sensitive paint (PSP) viewing through cast acrylic. Temperaturesensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at 𝑹𝒆 = 7.1 ×106 /m under conventional noise conditions. Transverse jet injection with jet-to-inlet mass-flow ratios up to 0.8 was used to induce unstart in the inlet/isolator. Background-oriented schlieren visualization of the inlet shocks was collected simultaneously with the PSP to determine when the inlet unstarted. Computational fluid dynamics results were used to determine off-wall flow structures and quantify approach …

Rapid-Prototyping Nanofabrication: Lcd-Based Projection Lithography And Physical Vapor Deposition, Sabeel Saleem Mohammmed

University Honors Theses

The semiconductor industry's continued growth, driven in large part by demand for artificial intelligence hardware, has highlighted the need for greater workforce development in regions adjacent to major fabrication centers like Oregon's Silicon Forest. This capstone project lays the groundwork for a small scale and student led semiconductor fabrication lab at Portland State University by demonstrating two of the core steps in chip manufacturing: photolithography and thin film deposition. Rather than relying on conventional fixed reticles, this work explores a unique, low cost approach to patterning that uses an ultraviolet-compatible liquid crystal display (LCD) as a programmable reticle, allowing arbitrary …

Improving The Reliability And Performance Of A Supersonic Indraft Tube Wind Tunnel, Christian J. Kaml

Master's Theses

Access to supersonic testing is increasing in demand, and wind tunnels remain one of the safest and most cost-effective methods for gathering high-speed flow data. Despite being more economical than alternative options, supersonic wind tunnel facilities often require substantial investment to construct, operate, and maintain.

The novel indraft tube tunnel architecture was conceived as a high-speed flow testbed that incorporates features of both Ludwieg tubes and indraft wind tunnels to maintain costs low enough to be accessible even to small universities. This design was first developed and tested in 2018 at California Polytechnic State University, featuring a cost per test …

Computational Insights Into Nucleosome Dynamics In Epigenetics Using Molecular Dynamics Simulations, Rutika Patel

Dissertations, Theses, and Capstone Projects

Nucleosome core particles (NCP) are the building blocks that form a highly organized and compact chromatin structure. Nucleosomes package DNA in the nucleus of eukaryotic cells. The NCP consists of about 147 base pairs of DNA wrapped around the histone octamer, with 1.65 superhelical turns in a left-handed manner. The histone octamer is composed of two copies of H3, H4, H2A, and H2B. Together with histone H1 and linker DNA, they further assemble into a higher-order chromatin structure. The nucleosome complex is stabilized by electrostatic interactions between positively charged histone residues and the negatively charged DNA backbone. To effectively access …

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Techno-Enviro-Economic Analysis Of Precipitated Calcium Carbonate Production From Carbon Dioxide In Cement Industry Flue Gas And Calcium Hydroxide, Natalia Debora Panggabean, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

CCUS is a technological solution to reduce emissions from the cement industry, which is the second largest CO2-intensive industry. This study aims to analyze technical, economic, and environmental performance of Precipitated Calcium Carbonate (PCC) synthesis in cement industry flue gas. The process simulation includes the CO2 capture system from cement plant, CO2 captured used as feedstock for PCC synthesis process through its reaction with calcium hydroxide. The simulation was carried out using ASPEN Plus software. Technical analysis was performed to determine the CO2 capture efficiency and PCC synthesis efficiency. Economic analysis was conducted to calculate CO2 capture cost and production …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Assessing Passenger Electric Vehicle Growth Strategies And Their Impacts On Electricity Demand Load And Co2 Emissions In Aceh Province To Achieve Net Zero Emission Target By 2060, Taufik Hidayat, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

The electrification of the transport sector is a crucial pathway for achieving Indonesia’s Net Zero Emissions (NZE) target by 2060. This study assesses the potential impact of passenger electric vehicle (EV) penetration on electricity demand and CO2 emissions in Aceh Province through a scenario-based modelling approach. Two policy-aligned scenarios are assessed: a low-penetration (LP) scenario and a high-penetration (HP) scenario. Using the Gompertz model and the ASIF framework, total CO2 emissions were projected from 2020 to 2060. Results show that although higher EV penetration reduces direct emissions from internal combustion engine (ICE) vehicles, total CO2 emissions increase more significantly under …

Agglomeration Of Particles Streaming Down A Zigzag, Juan Llamas

Posters - 2026

Zigzags or “letdown ladders” limit the flow speed of dry grains as they flow downward by gravity when loading silos, ships, barges, railcars, or trucks.

• Reduce cracking and shattering of grains.

• Increase grain shelf life.

• Increase grain resale value. • Increase ability of grain to germinate.

• Reduce generation of grain dust, an explosion and environmental hazard.

How can we design a zigzag that we know will not plug?

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Observations Of An Oscillatory Mechanochemical Reaction Between Tetrathiafulvalene And Chloranilic Acid, Alastair Deans

Physics Theses & Dissertations

Mechanochemistry is the study of chemical reactions driven by the input of mechanical en ergy in addition to thermal activation. Mechanochemical reactions from powders are carried out by manual grinding or milling using various types of ball mills, or in twin extruders. While mechanochemistry has great potential affording economically and environmentally advantageous “green” synthetic methods, a drawback is that its chemical mechanisms are not well understood. One example of such a reaction currently under study involves tetrathiafulvalene, an organic elec tron donor with two polymorphs (orange and brown), and chloranilic acid, an electron acceptor. Previous results show that neat grinding …

Ultra-High Vacuum Outgassing Characterization Of Thermally Processed Low-Carbon Steel For Advanced Particle Accelerator And Gravitational Wave Detector Applications, Aiman H. Al-Allaq

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation investigated AISI 1020 low-carbon steel as an alternative vacuum chamber material to conventional stainless steel for ultra-high vacuum (UHV) and extreme-high vacuum (XHV) applications. After a 400 °C/48 h bake, AISI 1020 tube chambers achieved a hydrogen outgassing rate of 2.4 × 10⁻¹⁶ Torr·L·s⁻¹·cm⁻², approximately 2,300 times lower than the prebaked 316L stainless-steel comparator, among the lowest hydrogen outgassing rates ever reported for an uncoated metallic vacuum chamber. Bare and magnetite-coated AISI 1020 chambers were then compared using throughput and rate-of-rise methods. The magnetite coating yielded 5× lower water outgassing at room temperature, but this advantage disappeared after …

A New Highly Oxygen-Deficient And Cubic Pr3Zro8-Δ For Intermediate-Temperature Thermochemical Production Of Oxygen And Hydrogen, Jiaxin Lu, Yongliang Zhang, Luhong Chen, Yan Chen, Ke An, Yasser Shoukry, Xinfang Jin, Zhi-Hao Wang, Sai Mu, Kevin Huang

Faculty Publications

Two-step thermochemical cycles offer a clean route for hydrogen and oxygen production but are typically limited to high temperatures exceeding 1500 °C. Lowering operating temperatures would enable the use of alternative heat sources such as industrial waste heat. Here, we report Pr₃ZrO₈ as a new enabling material for efficient intermediate-temperature redox cycling, with thermal reduction at 900 °C in argon and steam oxidation at 400 °C. Pr₃ZrO₈ adopts a face-centered cubic structure similar to CeO₂ but exhibits significantly greater oxygen deficiency, achieving average oxygen and hydrogen fluxes of 331.7 and 70.3 µmol·g-1, respectively, …

Crystal Structures, Optical Behavior, And Magnetic Properties In Hydrated Lanthanide Iron Sulfates, Chole Jones, Silu Huang, Tyler L. Spano, Eric A. Gabilondo, Mohammed Al-Fahdi, Kara Trim, Mary Douglas, Rongying Jin, Andrew Miskowiec, P. Shiv Halasyamani, Ming Hu, Jie Ling

Faculty Publications

Single crystals of LnFe(SO₄)₃(H₂O)₂ (Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm; compounds 1–11) and LnFe(SO₄)₃(H₂O) (Ln = Tm, Yb, Lu; compounds 12–14) were synthesized under hydrothermal conditions. Single-crystal X-ray diffraction (SCXRD) analysis revealed that the dihydrated compounds (1–11) crystallize in centrosymmetric (CS) structures, with the lanthanide ions adopting eight-coordinate geometries. In contrast, the monohydrated compounds (12–14) exhibit noncentrosymmetric (NCS) structures, where the lanthanide ions are seven-coordinated. Vibrating sample magnetometry (VSM) confirmed that compounds 2, …

Spectroscopic Investigations On Polyvinylidene Fluoride Nanofibers, Parinaz Amaniabdolmalaki, Jui Vitthal Kharade, Alexandro Trevino, Lydia Morales, Karen Lozano, Victoria Padilla, Karen S. Martirosyan, Horacio Vasquez, Mircea Chipara

Physics & Astronomy Faculty Publications

The production of polyvinylidene fluoride nanofibers by force-spinning from polymer solutions was confirmed by electron microscopy. The structural and phase characteristics of the resulting nanofiber mats were examined using Fourier Transform Infrared Spectroscopy in Attenuated Total Reflectance mode, Raman spectroscopy, and X-ray Diffraction. Results from all these techniques consistently indicated that both the powder and the mats of polyvinylidene fluoride predominantly contain the α phase, with a small admixture of the β phase. Within experimental errors, no other phases were noticed both in the powder and in the as-obtained mats. The ratios of the areas of the Raman lines at …

Guitar Amplifier Directivity, Rachel C. Edelman, Brian E. Anderson, Samuel D. Bellows, Timothy W. Leishman

Directivity

No abstract provided.

Microgravity-Induced Alterations In Left Atrial Hemodynamics And Thrombogenic Risk: Insights From Healthy And Atrial Fibrillation Models, Grace M. Hoeppner

Dissertations, Master's Theses and Master's Reports

Background: Microgravity exposure alters cardiovascular loading, yet its impact on left atrial flow dynamics and thrombotic risk remains poorly understood. This study investigates how spaceflight-relevant microgravity-induced changes in cardiac outflow affect left atrial hemodynamics in healthy individuals and patients with atrial fibrillation.

Methods: Patient-specific left atrial models were generated for three healthy individuals and three AF patients. Computational fluid dynamics (CFD) simulations were performed using each patient’s baseline mitral outflow waveform and two modified waveforms representing short- and long-duration post-flight cardiac loading changes derived from echocardiographic observations. Hemodynamic metrics included left atrial velocity, time averaged wall shear stress, oscillatory shear …

Computational Study Of Rotating Detonation Combustors, Aditya Balasubramaniam

Mechanical and Aerospace Engineering Theses

Rotating detonation combustors (RDCs) are pressure-gain combustion devices that sustain one or more continuously rotating detonation waves, offering potential thermodynamic and performance advantages over conventional deflagration-based systems. Their behavior depends strongly on combustor geometry and operating conditions. Understanding these effects is therefore essential for the design and optimization of practical RDCs. Accordingly, this thesis numerically investigates annular RDCs with two primary objectives: (1) to evaluate the effects of propellant mass flux and (2) to assess the influence of annular width on detonation-wave dynamics and combustor performance.

A finite-volume framework is used to solve the compressible reactive Euler equations with hydrogen–air …

Analytical Study Of Transient Mixed Convective Radiative Jeffrey Fluid Flow With Diffusion–Thermo And Chemical Reaction, V. Sathiya, R. Vijayaragavan, B. Rushi Kumar

Mansoura Engineering Journal

This research examines the behavior of unsteady mixed convective radiative Jeffrey fluid flow over a permeable moving plate with a diffusion thermo effect. The study incorporates multiple factors, including aligned magnetic fields, heat generation, radiation, and chemical reactions. The behavior of Jeffrey fluid under these combined conditions is particularly relevant to the design of efficient heat exchangers, MHD generators, and cooling systems for electronic components. A regular perturbation technique was employed to solve the governing equations, yielding distributions for velocity, temperature, and species concentration. These solutions enabled the derivation of expressions for skin friction, Nusselt number, and Sherwood number. Through …

Development And Characterization Of Flat And Flexible Rebco Cables For High-Field Accelerator Magnets, Emily Romancew

Graduate Research Theses & Dissertations

High-Temperature Superconducting (HTS) materials are at the forefront of innovation for fundamental particle physics. The next generation of particle accelerators aims to explore higher mass particles and is dependent on the ability to achieve higher fields in the 20–30 T range to keep machine size within a practical footprint. Current magnet technology relies on low-temperature superconductors (LTS) such as NbTi and Nb₃Sn, which are limited to fields of approximately 8–16 T, while high-temperature superconductors (HTS), particularly Rare-Earth Barium Copper Oxide (REBCO), offer a promising pathway toward higher-field magnets due to their ability to carry large currents at elevated magnetic fields. …

Stability Analysis Of Thermohaline Convection With A Time-Varying Shear Flow Using The Lyapunov Method, Kalin Kochnev

Honors Scholar Theses

This work applies the Lyapunov method to identify instabilities and compute the growth rate of a linear time-varying system. The linear system studied describes cold fresh water on top of hot salty water with a periodically time-varying background shear flow. A time-dependent weighting matrix is employed to construct a Lyapunov function candidate. The resulting linear matrix inequalities are discretized in time using the forward Euler method. As the number of temporal discretization points increases, the growth rate predicted by the Lyapunov method or Floquet theory, used for comparison, will converge to the same value obtained from numerical simulations. Furthermore, the …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …