Physics Commons^™

Analytical Study Of Transient Mixed Convective Radiative Jeffrey Fluid Flow With Diffusion–Thermo And Chemical Reaction, V. Sathiya, R. Vijayaragavan, B. Rushi Kumar

Mansoura Engineering Journal

This research examines the behavior of unsteady mixed convective radiative Jeffrey fluid flow over a permeable moving plate with a diffusion thermo effect. The study incorporates multiple factors, including aligned magnetic fields, heat generation, radiation, and chemical reactions. The behavior of Jeffrey fluid under these combined conditions is particularly relevant to the design of efficient heat exchangers, MHD generators, and cooling systems for electronic components. A regular perturbation technique was employed to solve the governing equations, yielding distributions for velocity, temperature, and species concentration. These solutions enabled the derivation of expressions for skin friction, Nusselt number, and Sherwood number. Through …

Comparison Of Push-Pull Air Curtain To Overhead Downdraft Systems On Aerosol Containment And Distribution In Controlled Environments, Manal Mutairi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Abstract

Comparison of Push-Pull Air Curtain to Overhead Downdraft Systems on Aerosol Containment and Distribution in Controlled Environments.

This dissertation looks at the ongoing issue of tiny airborne particles created during medical and dental procedures and evaluates ways to reduce the risk of exposure for healthcare workers and patients to these particles. The first study focuses on the size, how long particles stay in the air, and how far they travel from common medical procedures that create aerosols, showing that tiny particles (less than 5 µm) can stay in the air long enough to escape basic droplet controls. As a …

Stability Analysis Of Thermohaline Convection With A Time-Varying Shear Flow Using The Lyapunov Method, Kalin Kochnev

Honors Scholar Theses

This work applies the Lyapunov method to identify instabilities and compute the growth rate of a linear time-varying system. The linear system studied describes cold fresh water on top of hot salty water with a periodically time-varying background shear flow. A time-dependent weighting matrix is employed to construct a Lyapunov function candidate. The resulting linear matrix inequalities are discretized in time using the forward Euler method. As the number of temporal discretization points increases, the growth rate predicted by the Lyapunov method or Floquet theory, used for comparison, will converge to the same value obtained from numerical simulations. Furthermore, the …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

Measurements Of Water-Film Thickness On Cave Walls And Speleothems, Alexandre Honiat, Salaheddine Skali-Lami, François Bourges, Bruno Lartiges

International Journal of Speleology

The water-film that coats cave walls and speleothems is a key player for the regulation of cave microclimate and the control of speleothem growth. In this paper, we demonstrate the capability of a confocal optical sensor to quantitatively measure on-site the rapid variations of water-film thickness when dripping, active condensation, or dryness occur on walls of various caves. Results obtained from a sample of four prehistoric caves and one stalagmite cave from Southwest France, indicate that the measurable thickness of water-films is generally in the 25-70 µm range for cave walls and reaches 200-300 µm on the horizontal plane of …

Unsaturated Fatty Acid Oil-Based Microdroplets: A Promising Novel Class Of Microdroplets, Ramiz S. Alejilat

Seton Hall University Dissertations and Theses (ETDs)

Droplet-based microfluidics has rapidly advanced numerous fields, including chemistry, biology, materials science, medicine, food science, and cosmetics. In these systems, fluorocarbon oil combined with fluorinated surfactants is the preferred medium for fluid encapsulation, offering exceptional stability and biocompatibility essential for sensitive biological and chemical processes. However, growing concerns about the environmental and biological risks associated with fluorinated chemicals have prompted a search for alternatives.

This study is the first to explore the use of unsaturated fatty acids derived from emu oil for microdroplet formation. We characterized droplet formation based on flow rates and the presence non-fluorinated surfactant at a certain …

Coupled Machine Learning Models: Combining Observations And Numerical Analysis In A Physics-Regularized Approach, Austin B. Schmidt

LSU New Orleans Theses and Dissertations

This dissertation investigates surrogate modeling for fixed-location environmental forecasting using novel data-combination techniques. The work surveys the landscape of observational measurements and numerically generated data, identifying similar research and gaps in current methodologies. The ratio-coupled training framework is introduced to combine two data sources per predicted feature through a tunable parameter that weights training signal strength. An optimization scheme is developed to simultaneously tune surrogate weights and the coupled signal ratio, allowing relative influence between signals to act as an explicit regularizer. Three case studies demonstrate the methodology and approach in a variety of contexts. The first study is based …

On The Scalability Of Anisotropic Mesh Adaptation On Distributed And Shared Memory Architectures For Numerical Approximations, Kevin Mark Garner Jr.

Computer Science Theses & Dissertations

Mesh generation is a critical component in numerical approximations of Partial Differential Equations (PDEs). One such example includes Computational Fluid Dynamics (CFD), as CFD simulations in turn are crucial for applications in many industries, such as personalized healthcare and the design of aerospace vehicles. Generating high quality meshes for large-scale CFD problems presents a significant bottleneck in the CFD workflow. This dissertation proposes “fast,” parallel 3D mesh generation methodologies that are designed to leverage the concurrency offered by emerging High-Performance Computing (HPC) architectures. First, a distributed memory method is presented that integrates a sequential state-of-the-art isotropic, advancing front local reconnection-based …

Living Shoreline Prioritization And Hydrodynamic Habitat Suitability Models For Restoration In The Indian River Lagoon And Lake Worth Lagoon, Florida, Kelly M. Kibler, Melinda J. Donnelly, Vincent Encomio, Madison Giuntoli, Manisha Thenuwara, Brice Bennett, Laura Andrade Barron, Mariam Sonbol, Wynter Raine Seppala, Namritha Ramakrishnan, Jennifer Jordan Báez, Beth Orlando, Irene Arpayoglou, Melissa Meisenburg

Indian River Lagoon Shorelines

The spatial dataset: UCF_shorelinemodel_IRL_LWL.shp, was created with support from the Indian River Lagoon National Estuaries Program and Florida Sea Grant. These projects cumulatively led to creation of a living shoreline restoration prioritization model and hydrodynamic habitat suitability models for 1,550 km (963 miles) of estuarine shorelines in Indian River Lagoon and Lake Worth Lagoon.

The dataset presented herein includes:

1. shoreline data from >15,000 transects collected in the field,
2. shoreline wave climate data created through hydrodynamic modeling and frequency analysis of historic data,
3. categorization of potential risk for shoreline boat wake impact,
4. persistence of seagrass within 210 m of the shoreline, …

The Role Of Atmospheric Turbulence On Cloud Droplet Distribution And Droplet Impaction On An Airfoil, Arash Shad, Hashnayne Ahmed, ‪Nadim Zgheib, S. Balachandar, S. A. Sherif

Mechanical Engineering Faculty Publications

We conduct turbulence-informed Euler–Lagrange simulations of droplet-laden flow to examine the effects of atmospheric turbulence on droplet impingement characteristics on a NACA 0012 airfoil. We implement statistical overloading, whereby we inject millions of droplets, ranging in diameter from 1 to 160 microns, upstream of the airfoil at an average streamwise velocity of 120 m/s. Within a fraction of a second, these droplets would have either impinged on the airfoil or continued downstream. While the incoming air flow is maintained uniform, droplet injection is informed by ambient turbulence, affecting both the droplet velocity distribution as well as the size-dependent preferential concentration …

Design Principles For Deployable Fibers Inspired By Hagfish Defense, Mohammad Tanver Hossain, Wonsik Eom, Pallab Layak, Jeongmin Kim, Carolyn Darling, Andrew Lowe, Douglas S. Fudge, Sameh H. Tawfick, Randy Ewoldt

Biology, Chemistry, and Environmental Sciences Faculty Articles and Research

Hagfish produce extraordinary slime as a defense mechanism, releasing exudate from glands that rapidly form a fibrous, soft, ultra-dilute, water-capturing network upon contact with seawater (up to 10 000 times its original volume). The gland thread cell (GTC) produces high-strength protein threads (filament diameter df = 1–3 µm) meticulously coiled into skeins (coil diameter Do ∼ 150 µm) that rapidly unravel upon deployment to reveal their hidden length (Lf = 15 cm), forming a cohesive fibrous slime network through interaction with mucin vesicles and seawater. To date, no engineered material is able to replicate the fiber …

Meshless Discrete Velocity Boltzmann Model For Porous Media Flow, Amandine Maidenberg

Doctoral Dissertations and Master's Theses

This dissertation explores the combination of two sophisticated techniques for addressing computational fluid dynamics: the discrete velocity Boltzmann equation (DVBE) and the localized collocation meshless model with upwinding (U-LCMM). The DVBE is a high-level model that describes the foundations of transport phenomena by addressing the microscale motions of particles themselves and the effect of their aggregate behaviors on continuum principles. This equation integrates multiple scales of phenomena; while it can be used for fluid flow at Navier-Stokes scales, it can also resolve fine features that can only be described at the molecular level. This type of model is necessary for …

Analytical Solutions For Transitional Flow Around Hydrometeors: Implications For Particle Dynamics And Atmospheric Modeling, Ahmad Talaei, Timothy J. Garrett

Physics Student Research

Accurate modeling of hydrometeor dynamics is critical for advancing weather and climate predictions. However, this remains a long-standing challenge in atmospheric science, particularly within the transitional Reynolds number regime, due to the lack of analytical solutions to the Navier–Stokes equations. This study presents two analytical solutions for two-dimensional, incompressible, and viscous flow around a sphere, addressing the gap between low and high Reynolds number regimes. The first framework, an extension of classical expansion methods using hypergeometric, provides a direct analytical relation that characterizes separation angle across the transitional regime. To address post- separation dynamics, a second formulation based on a …

Performance Analysis Of Flapping-Foil Energy Harvesters Under Shear-Flow Conditions, Maqusud Alam, Bubryur Kim, Shehnaz Akhtar, Sujeen Song, Zengshun Chen, Jinwoo An

Civil Engineering Faculty Publications

Flapping-foil energy harvesters represent a promising technology for extracting energy from fluid flows, although their performance under shear-flow conditions is poorly understood. To address this research gap, we investigated the impact of power-law shear flow on the performance of flapping-foil energy harvesters. We conducted numerical simulations at different Reynolds numbers (Re = 1000, 50 000, and 500 000) under uniform-flow and shear-flow conditions. Based on the results, shear flow minimally affected the power outputs at Re = 1000 and 50 000, where viscous forces dominate the flow dynamics. However, at Re = 500 000, shear flow significantly reduced the …

Investigation Of Co-Current And Counter-Current Multiphase Flow In Upstream Drilling And Production Applications, Hazem Fleifel

LSU Doctoral Dissertations

In the domain of upstream Petroleum Engineering, the dynamics of co-current and counter-current multiphase flows present huge challenges, significantly impacting the efficiency of associated processes. This study investigates two specific applications concerning these flow behaviors, involving both laboratory experiments and transient computer simulations. This work investigates two distinct well control and production enhancement processes, involving multiphase flow dynamics: the bullheading kill procedure and liquid-assisted gas lift (LAGL).

The first topic (Topic 1) explores the bullheading process, a type of well control methods, by challenging the traditional understanding that gas removal efficiency increases monotonically with injection pump flow rate. Through 1D …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Stokes-Dependent Droplet Collection Efficiency On A Naca 0012 Airfoil From Droplet-Informed Simulations With Statistical Overloading, Arash Shad, Hashnayne Ahmed, ‪Nadim Zgheib, S. Balachandar, S. A. Sherif

Mechanical Engineering Faculty Publications

Accurate modelling of ice accretion on aircraft wings requires analysing droplet impingement on the surface to optimize the design of ice-protection systems. We perform Euler–Lagrange simulations of a droplet-laden flow impinging on a NACA 0012 airfoil. Our study includes water droplets with eight discrete sizes ranging from 1 to 160 microns. We vary the free-stream velocity of the incoming airflow in the range 60≤⁢𝑈≤⁢240 m s−1 and the chord length of the airfoil in the range 0.5≤⁢𝑐≤⁢2 m. Due to the dilute nature of supercooled clouds, one-way coupling is used in the simulations. The effects of droplet breakup and collision …

A Rigorous Framework For An Improved Messinger/Myers Model Of Ice Accretion Under Conditions Of Variable Property And Unsteady Aircraft Icing, Hashnayne Ahmed, Arash Shad, ‪Nadim Zgheib, S. A. Sherif, S. Balachandar

Mechanical Engineering Faculty Publications

We analyse the Messinger/Myers model by critically evaluating simplifying assumptions through a rigorous formulation of the rime ice accretion process. We explore the effects of both constant and variable ice density and thermal conductivity, along with the effects of sublimation from the ice surface. The effects of key factors such as droplet impact rate, ambient temperature relative to the freezing temperature and the temperature difference between the ambient air and the airfoil surface are examined. Under these varying conditions, the present rigorous formulation is used to assess the significance of unsteady effects, variable ice properties and sublimation. We observe that …

Numerical Simulation Of Frost Formation And Heat Transfer On Fin-And-Tube Heat Exchangers In Turbulent Cross-Flow, Mahsan Farzaneh, ‪Nadim Zgheib, S. Balachandar, S. A. Sherif

Mechanical Engineering Faculty Publications

Frost formation in fin-and-tube heat exchangers in turbulent cross-flow presents significant challenges in industrial refrigeration applications, affecting heat transfer efficiency and operational reliability. The purpose of this work is to investigate frost deposition and growth on a staggered bank of a fin-and-tube freezer coil under turbulent forced convection conditions. The focus here is on investigating conditions that closely replicate real-world scenarios in large walk-in industrial freezers. Using a direct numerical simulation approach, we examine the flow dynamics and thermal behaviour in the presence of frost, considering turbulent regimes characterized by a Reynolds number in the range 1050≤𝑅⁢𝑒𝐷,avg≤4800, with the characteristic …

Theoretical And Experimental Investigation Of Liquid-Liquid Phase Separation: Characterizing Elastin-Like-Polypeptides, Adam D. Quintana

Chemical and Biological Engineering ETDs

This dissertation develops and validates a semi-empirical Flory–Huggins-based interaction model, combined with Cahn–Hilliard simulations, for predicting multi-component liquid–liquid phase separation (LLPS) in elastin-like polypeptide (ELP) systems. Equilibrium droplet compositions, measured using a PDMS-based microfluidic device, enabled direct parameterization of interaction coefficients. The model was applied to generate phase diagrams and assess composition dependence in ternary mixtures. Cahn–Hilliard simulations were conducted to explore potential phase morphologies under different interfacial conditions. Multi-component Lattice Boltzmann simulations were implemented to model droplet morphology evolution under varying interfacial and diffusive parameters, reproducing experimentally relevant morphologies. A three-phase wetting study revealed conditions for selective wetting and …

Revised Unsteady Drag Force And Its Impact On Particle Dynamics At High Reynolds Numbers, Ahmad Talaei, Timothy J. Garrett

Physics Student Research

The accurate modeling of particle motion in viscous fluids at high Reynolds numbers remains a fundamental challenge, particularly under unsteady flow conditions where nonlinear effects dominate. This study introduces a revised unsteady drag formulation, extending its applicability beyond previous studies. By integrating classical solutions of the Navier–Stokes equations, the new formulation overcomes the limitations of the Maxey–Riley–Gatignol (MRG) equation, addressing non-physical memory effects associated with Basset drag and extending its applicability to higher Reynolds numbers.

Through experimental comparisons and direct numerical simulations (DNS), the revised equation of motion is compared to the MRG equation, both during steady-state conditions and non-equilibrium …

Nonlinear Physics Of Parity-Broken Fluids, Sudheesh Srivastava

Dissertations, Theses, and Capstone Projects

This thesis explores parity-breaking mechanisms, nonlinear wave phenomena, and localization transitions across different physical contexts. First, we examine modulation instability in parity-breaking systems, deriving modified nonlinear Schr¨odinger equations that reveal direction dependent instabilities. Next, we investigate wave turbulence, demonstrating numerically that parity-breaking dispersion significantly alters turbulent cascades and modifies their statistical properties. Lastly, we analyze localization in quasiperiodic tight- binding model based on polariton condensate lattice. Collectively, these studies illustrate the universal role of symmetries and nonlinear interactions in shaping macroscopic behaviors, facilitating interdisciplinary insights.

Gravity Wave Breaking Over Northern Utah With An Advanced Mesospheric Temperature Mapper And Sodium Lidar, Eric Davis

All Graduate Reports and Creative Projects, Fall 2023 to Present

Considerable progress has been made in recent decades in the understanding of gravity wave (GW) dynamics. However, there remain important aspects and effects that are poorly understood. In particular, the coupling and deposition of their energy and momentum into the mesosphere lower thermosphere (MLT) region and the interaction and instability dynamics that are directly associated with GW breaking. Using an Advanced Mesosphere Temperature Mapper (AMTM) several strong wave breaking events were observed in the summer of 2015 at USU’s BLO research station. These events have exhibited high momentum fluxes and associated strong wave breaking, prompting detailed data analyses. Rossby waves, …

Flow Field Surrounding Bluegill (Lepomis Macrochirus) During Suction-Feeding, Jensine Caroline Coggin

Electronic Theses and Dissertations

Suction-feeding is a common method for capturing prey by aquatic organisms and contributed to the diversification of fishes by enabling them to consume a wide range of prey. Suction-feeding is a complex fish-fluid interaction governed by various hydrodynamic forces: inertia, unsteady, viscous, and pressure gradients. These forces are described by the coupling between the flow physics equations (Navier-Stokes) and the dynamic behavior of the fish (motion and forces). However, the distribution of the pressure field that drives this process, and the extent to which suction-feeding is three-dimensional, remain underexplored. I estimated the pressure within the flow field surrounding the mouth …