Physics Commons^™

Computational Design Optimization For Microfluidic Magnetophoresis, Brian Dennis Plouffe, Laura H. Lewis, Shashi Krishna Murthy

Laura H. Lewis

Current macro- and microfluidic approaches for the isolation of mammalian cells are limited in both efficiency and purity. In order to design a robust platform for the enumeration of a target cell population, high collection efficiencies are required. Additionally, the ability to isolate pure populations with minimal biological perturbation and efficient off-chip recovery will enable subcellular analyses of these cells for applications in personalized medicine. Here, a rational design approach for a simple and efficient device that isolates target cell populations via magnetic tagging is presented. In this work, two magnetophoretic microfluidic device designs are described, with optimized dimensions and …

Fully Coupled Fluid And Electrodynamic Modeling Of Plasmas: A Two-Fluid Isomorphism And A Strong Conservative Flux-Coupled Finite Volume Framework, Richard Joel Thompson

Doctoral Dissertations

Ideal and resistive magnetohydrodynamics (MHD) have long served as the incumbent framework for modeling plasmas of engineering interest. However, new applications, such as hypersonic flight and propulsion, plasma propulsion, plasma instability in engineering devices, charge separation effects and electromagnetic wave interaction effects may demand a higher-fidelity physical model. For these cases, the two-fluid plasma model or its limiting case of a single bulk fluid, which results in a single-fluid coupled system of the Navier-Stokes and Maxwell equations, is necessary and permits a deeper physical study than the MHD framework. At present, major challenges are imposed on solving these physical models …

Investigation Of Time And Position Resolved Alpha Transducers For Multi-Modal Imaging With A D-T Neutron Generator, Joshua William Cates

Doctoral Dissertations

Deuterium-Tritium (D-T) neutron generators have been used as an active interrogation source for associated particle imaging (API) techniques. The D-T reaction yields a 14.1 MeV neutron and a 3.5 MeV alpha (or assoicated) particle, projected nearly back-to-back. The kinetics of the reaction allow the direction and initial time of the neutron to be determined utilizing position sensitive detectors for both the alpha and neutron. This information facilitates multi-modal fast neutron imaging of inspection objects and closed containers to infer the geometry within them and the presence of special nuclear material (SNM). Since position and time of interaction of the alpha …

Characterization Of Samples For Optimization Of Infrared Stray Light Coatings, Carey L. Baxter, Rebecca Salvemini, Zaheer A. Ali, Patrick Waddell, Greg Perryman, Bob Thompson

STAR Program Research Presentations

NASA’s Stratospheric Observatory for Infrared Astronomy (SOFIA) is a converted 747SP that houses a 2.5 m telescope that observes the sky through an opening in the side of the aircraft. Because it flies at altitudes up to 45,000 feet, SOFIA gets 99.99% transmission in the infrared. Multiple science instruments mount one at a time on the telescope to interpret infrared and visible light from target sources. Ball Infrared Black (BIRB) currently coats everything that the optics sees inside the telescope assembly (TA) cavity in order to eliminate noise from the glow of background sky, aircraft exhaust, and other sources. A …

Characterization Of The Drilling Via The Vibration Augmenter Of Rotary-Drills And Sound Signal Processing Of Impacted Pipe As A Potential Water Height Assessment Tool, Nicholas Morris

STAR Program Research Presentations

The focus of the internship has been on two topics: a) Characterize the drilling performance of a novel percussive augmenter – this drill was developed by the JPL’s Advanced Technologies Group and its performance was characterized; and b) Examine the feasibility of striking a pipe as a means of assessing the water height inside the pipe. The purpose of this investigation is to examine the possibility of using a simple method of applying impacts to a pipe wall and determining the water height from the sonic characteristic differences including damping, resonance frequencies, etc. Due to multiple variables that are relevant …

Scitech Book News Reviews, Susan Fingerman

Sci-Tech News

No abstract provided.

Feedback Stabilization At Spear3, Daniel Kelley, Jeff Corbett

STAR Program Research Presentations

The SPEAR3 synchrotron lightsource at SLAC relies on a sophisticated radio frequency (RF) timing system to maintain current – electrons – in the storage ring. One problem SPEAR3 operators have dealt with is the thermal expansion of one of the cables supporting this RF timing system. As the cable expands and contracts with the diurnal rise and fall of the sun, the phase of the RF in the cable shifts. This shifting phase affects the timing accuracy of electron injections into the storage ring.

A common feedback control algorithm PID (Proportional Integral Derivative) has countless applications in engineering. PID feedback …

Numerical Examination Of Acousto-Optic Bragg Interactions For Profiled Lightwaves Using A Transfer Function Formalism, Monish Ranjan Chatterjee, Fares S. Almehmadi

Electrical and Computer Engineering Faculty Publications

Classically, acousto-optic (AO) interactions comprise scattering of photons by energetic phonons into higher and lower orders. Standard weak interaction theory describes diffraction in the Bragg regime as the propagation of a uniform plane wave of light through a uniform plane wave of sound, resulting in the well-known first- and zeroth-order diffraction.

Our preliminary investigation of the nature of wave diffraction and photon scattering from a Bragg cell under intensity feedback with profiled light beams indicates that the diffracted (upshifted photon) light continues to maintain the expected (uniform plane wave) behavior versus the optical phase shift in the cell within a …

Adaptive Wiener Filter Super-Resolution Of Color Filter Array Images, Barry K. Karch, Russell C. Hardie

Electrical and Computer Engineering Faculty Publications

Digital color cameras using a single detector array with a Bayer color filter array (CFA) require interpolation or demosaicing to estimate missing color information and provide full-color images. However, demosaicing does not specifically address fundamental undersampling and aliasing inherent in typical camera designs. Fast non-uniform interpolation based super-resolution (SR) is an attractive approach to reduce or eliminate aliasing and its relatively low computational load is amenable to real-time applications. The adaptive Wiener filter (AWF) SR algorithm was initially developed for grayscale imaging and has not previously been applied to color SR demosaicing. Here, we develop a novel fast SR method …

High-Performance, Scalable Optical Network-On-Chip Architectures, Xianfang Tan

UNLV Theses, Dissertations, Professional Papers, and Capstones

The rapid advance of technology enables a large number of processing cores to be integrated into a single chip which is called a Chip Multiprocessor (CMP) or a Multiprocessor System-on-Chip (MPSoC) design. The on-chip interconnection network, which is the communication infrastructure for these processing cores, plays a central role in a many-core system. With the continuously increasing complexity of many-core systems, traditional metallic wired electronic networks-on-chip (NoC) became a bottleneck because of the unbearable latency in data transmission and extremely high energy consumption on chip. Optical networks-on-chip (ONoC) has been proposed as a promising alternative paradigm for electronic NoC with …

Structural Properties Of Ferroelectric Lead (Zirconium0.5,Titanium0.5)Oxygen3 Nanotube Array And Electronic Structure Of Lao Delta-Doped Strontium Titanate, Rajendra Prasad Adhikari

Graduate Theses and Dissertations

In this Dissertation we begin with two introductions on: 1) ferroelectricity and related phenomena, and 2) novel properties of Oxide electronics and the generation of two dimensional electron gas. We then give theoretical background of density functional theory (including LDA+U) and pseudopotentials. The first part of research work is about structural, polarization, and dielectric properties of ferroelectric Lead Zirconate Titanate (PZT) solid solution in the form of a nanotube array, embedded in a matrix medium of different ferroelectric strengths. We use the effective Hamiltonian derived from first-principles and finite-temperature Monte Carlo methods to determine the various properties. We revealed different …

Study Of A Non-Equilibrium Plasma Pinch With Application For Microwave Generation, Ahmad Al Agry

UNLV Theses, Dissertations, Professional Papers, and Capstones

The Non-Equilibrium Plasma Pinch (NEPP), also known as the Dense Plasma Focus (DPF) is well known as a source of energetic ions, relativistic electrons and neutrons as well as electromagnetic radiation extending from the infrared to X-ray. In this dissertation, the operation of a 15 kJ, Mather type, NEPP machine is studied in detail. A large number of experiments are carried out to tune the machine parameters for best performance using helium and hydrogen as filling gases. The NEPP machine is modified to be able to extract the copious number of electrons generated at the pinch. A hollow anode with …

Multiscale Study Of Batio3 Nanostructures And Nanocomposites, Lydie Louis Louis

Graduate Theses and Dissertations

Advancements in integrated nanoelectronics will continue to require the use of unique materials or systems of materials with diverse functionalities in increasingly confined spaces.

Hence, research on finite-dimensional systems strive to unearth and expand the knowledge of fundamental physical properties in certain key materials which exhibit numerous concurrent and exploitable functions.

Correspondingly, ferroelectric nanostructures, which particularly display a plethora of complex phenomena, prevalent in countless fields of research, are noteworthy candidates. Presently, however, the assimilation of zero-(0D) and one-dimensional (1D) ferroelectric into micro- or nano-electronics has been lagging, in part due to a lack of applied and fundamental studies but …

Investigation Of Negative Index In Dispersive, Chiral Materials Via Contra-Propagating Velocities Under Second-Order Dispersion (Gvd), Monish Ranjan Chatterjee, Tarig A. Algadey

Electrical and Computer Engineering Faculty Publications

Negative refractive index arises typically in metamaterials via multiple routes. One such avenue is the condition where the Poynting vector of the electromagnetic wave is in opposition to the group velocity in the material. An earlier work along this route in a chiral material led to the well-known result of requiring very large (non-realizable) chirality.

Thereafter, a combination of chirality together with first-order dispersion was examined using plane wave electromagnetic analysis. To arrive at the conclusions in that approach, the three wave velocities (energy, group and phase) were derived under first-order dispersion in permittivity, permeability and chirality. Negative index in …

Growth Of Zno Thin Films On Polar Oxide Surfaces By Atomic Layer Deposition, Kallol Pradhan

Theses and Dissertations

Polar heterointerfaces of MgO(111) and the II-VI semiconductor ZnO are of technological interest for transparent conducting electrode applications. Growth and structure of thin films on polar surfaces can be different than on non-polar surfaces due to the large surface energy of polar surfaces. We have grown ZnO on unreconstructed MgO(111)-(1x1)-OH terminated and reconstructed MgO(111)-(√3x√3)R30° polar oxide surfaces using atomic layer deposition. A homemade UHV-interfaced viscous-flow atomic layer deposition (ALD) reactor with in-situ quartz crystal monitor was used to grow ZnO thin films on the MgO(111) substrates. Surface morphology studies revealed that the surface roughness increases with ZnO film thickness and …

55th Annual Rocky Mountain Conference On Magnetic Resonance

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 55th annual meeting of the Rocky Mountain Conference on Magnetic Resonance, co-endorsed by the Colorado Section of the American Chemical Society and the Society for Applied Spectroscopy. Held in Denver, Colorado, July 28 - August 1, 2013.

Influence Of Microstructure On The Propagation Of Fatigue Cracks In Inconel 617, Benjiman Michael Albiston

Boise State University Theses and Dissertations

Inconel 617 is a candidate material for use in the intermediate heat exchanger of the Next Generation Nuclear Plant. Because of the high temperatures and the fluctuations in stress and temperature, the fatigue behavior of the material is important to understand. The goal of this study was to determine the influences of the microstructure during fatigue crack propagation. For this investigation, Inconel 617 compact tension samples, fatigue tested by Julian Benz at the Idaho National Laboratory, were obtained. The testing conditions included two environments at 650 °C (lab air and impure-He) and varied testing parameters including: loading waveform (triangular, trapezoidal), …

All-Optical Sigma-Delta Modulator For Analog-To-Digital Conversion, Bin Zhang

Graduate Theses - Physics and Optical Engineering

In this thesis, an all-optical sigma-delta (ΣΔ) modulator for analog-to-digital conversion (ADC) using a novel optical bistable switch, the SOA-PD device, is demonstrated. The presented all-optical ΣΔ modulator consists of a photonic leaky integrator, the SOA-PD optical comparator, and a positive feedback loop. The switching properties of the SOA-PD device are studied and experimentally tested to confirm its performance. Then the all-optical ΣΔ modulator is designed according to the switching performance of the SOA-PD device. It is demonstrated that the all-optical ΣΔ modulator is capable of producing an inverted non-return-to-zero (NRZ) type binary output for frequencies in the range of …

Field Emission Studies Toward Improving The Performance Of Dc High Voltage Photoelectron Guns, Mahzad Bastaninejad

Mechanical & Aerospace Engineering Theses & Dissertations

Field emission is the main mechanism that prevents DC high voltage photoemission electron guns from operating at the very high bias voltages required to produce low emittance beams. Gas conditioning is shown to eliminate field emission from cathode electrodes used inside DC high voltage photoelectron guns. Measurements and simulation results indicate that gas conditioning eliminates field emission from cathode electrodes via two mechanisms: sputtering and implantation, with the benefits of implantation reversed by heating the electrode. The field emission characteristics of 5 stainless steel electrodes varied significantly upon the initial application of voltage but improved to nearly the same level …

Spatiotemporal Fluorescent Detection Measurements Using Embedded Waveguide Sensors, Mark C. Harrison, Andrea M. Armani

Engineering Faculty Articles and Research

Integrated waveguide biosensors, when combined with fluorescent labeling, have significantly impacted the field of biodetection. While there are numerous types of waveguide sensors, the fundamental excitation method is fairly consistent: the evanescent field of the waveguide excites a fluorophore whose emission is detected, either directly via imaging or indirectly via a decrease in power transfer. Recently, a sensor device was demonstrated which is able to back-couple the emitted light into the waveguide, allowing the signal to be detected directly. However, this previous work focused on the development of an empirical model, leaving many theoretical questions unanswered. Additionally, the results from …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Nbconvert Refactor, Jonathan Frederic

Physics

IPython is an interactive Python computing environment. It provides an enhanced interactive Python shell. The IPython Notebook is a browser based interface distributed with IPython. It enables the creation of richly formatted notebooks that contain embedded IPython code. With nbconvert, notebooks can be exported to various formats including, but not limited to, LaTeX, reveal.js, RST, and HTML. This is important for users that want to be able to share their work outside of IPython. This senior project is the addition of a Sphinx LaTeX output format and the refactor of nbconvert.

Organic Solar Cells Based On High Dielectric Constant Materials: An Approach To Increase Efficiency, Khalil Jumah Tawfiq Hamam

Dissertations

The efficiency of organic solar cells still lags behind inorganic solar cells due to their low dielectric constant which results in a weakly screened columbic attraction between the photogenerated electron-hole system, therefore the probability of charge separating is low. Having an organic material with a high dielectric constant could be the solution to get separated charges or at least weakly bounded electron-hole pairs. Therefore, high dielectric constant materials have been investigated and studied by measuring modified metal-phthalocyanine (MePc) and polyaniline in pellets and thin films. The dielectric constant was investigated as a function of temperature and frequency in the range …

Atmospheric Pressure He-Air Plasma Jet: Breakdown Process And Propagation Phenomenon, Asma Begum, Mounir Laroussi, Mohammad Rasel Pervez

Electrical & Computer Engineering Faculty Publications

In this paper He-discharge (plasma jet/bullet) in atmospheric pressure air and its progression phenomenon has been studied experimentally using ICCD camera, optical emission spectroscopy (OES) and calibrated dielectric probe measurements. The repetitive nanosecond pulse has applied to a plasma pencil to generate discharge in the helium gas channel. The discharge propagation speed was measured from the ICCD images. The axial electric field distribution in the plasma jet is inferred from the optical emission spectroscopic data and from the probe measurement. The correlation between the jet velocities, jet length with the pulse duration is established. It shows that the plasma jet …

Creating Low-Cost ‘Balloonsats’ For Stem Education With 3d Printing, Jeremy Straub

Jeremy Straub

A new technology, known as 3D printing, allows the rapid fabrication of plastic structures of virtually any configuration. These structures are light-weight, durable and inexpensive. This paper considers the utility of utilizing 3D printing to create enclosures for ‘BalloonSats’ – small, low-cost spacecraft analog which can be utilized by students to understand space engineering, conduct near-space science (e.g., physics, biological and other experiments) and touch the edge of space.

The utility of 3D printed structures for use in the near-space low-temperature and low-pressure environment is considered. This analysis falls into four key areas. First, the ability of the structures to …

Distortion Management In Slow-Light Pulse Delay, Michael D. Stenner, Mark A. Neifeld, Zhaoming Zhu, Andrew M.C. Dawes, Daniel J. Gauthier

Andrew M C Dawes

We describe a methodology to maximize slow-light pulse delay subject to a constraint on the allowable pulse distortion. We show that optimizing over a larger number of physical variables can increase the distortion-constrained delay. We demonstrate these concepts by comparing the optimum slow-light pulse delay achievable using a single Lorentzian gain line with that achievable using a pair of closely-spaced gain lines. We predict that distortion management using a gain doublet can provide approximately a factor of 2 increase in slow-light pulse delay as compared with the optimum single-line delay. Experimental results employing Brillouin gain in optical fiber confirm our …

Modeling A Sensor To Improve Its Efficacy, Nabin K. Malakar, Daniil Gladkov, Kevin H. Knuth

Physics Faculty Scholarship

Robots rely on sensors to provide them with information about their surroundings. However, high-quality sensors can be extremely expensive and cost-prohibitive. Thus many robotic systems must make due with lower-quality sensors. Here we demonstrate via a case study how modeling a sensor can improve its efficacy when employed within a Bayesian inferential framework. As a test bed we employ a robotic arm that is designed to autonomously take its own measurements using an inexpensive LEGO light sensor to estimate the position and radius of a white circle on a black field. The light sensor integrates the light arriving from a …

Novel Bimetallic Plasmonic Nanomaterials, Ritesh Sachan

Doctoral Dissertations

Plasmonic nanomaterials have attracted a lot of attention recently due to their application in various fields such as chemical and biological sensing, catalysis, energy harvesting and optical devices. However, there is a need to address several outstanding issues with these materials, including cost-effective synthesis, tunability in plasmonic characteristics, and long term stability. In this thesis, we have focused on bimetallic nanoparticles (NPs) of Ag and Co due to their immiscibility as well as their individual properties. First, a pulsed laser induced dewetting route was used to synthesize Ag-Co bimetallic plasmonic NPs. An synthesis parameter space was derived to show the …

Femtosecond Laser Patterned Templates And Imprinted Polymer Structures, Deepak Rajput

Doctoral Dissertations

Femtosecond laser machining is a direct-write lithography technique by which user-defined patterns are efficiently and rapidly generated at the surface or within the bulk of transparent materials. When femtosecond laser machining is performed with tightly focused amplified pulses in single-pulse mode, transparent substrates like fused silica can be surface patterned with high aspect ratio (>10:1) and deep (>10 μm) nanoholes. The main objective behind this dissertation is to develop single-pulse amplified femtosecond laser machining into a novel technique for the production of fused silica templates with user-defined patterns made of high aspect ratio nanoholes. The size of the …

A Gamos Plug-In For Geant4 Based Monte Carlo Simulation Of Radiation-Induced Light Transport In Biological Media, Adam K. Glaser, Stephen C. Kanick, Rongxiao Zhang, Pedro Arce, Brian W. Pogue

Dartmouth Scholarship

We describe a tissue optics plug-in that interfaces with the GEANT4/GAMOS Monte Carlo (MC) architecture, providing a means of simulating radiation-induced light transport in biological media for the first time. Specifically, we focus on the simulation of light transport due to the Čerenkov effect (light emission from charged particle's traveling faster than the local speed of light in a given medium), a phenomenon which requires accurate modeling of both the high energy particle and subsequent optical photon transport, a dynamic coupled process that is not well-described by any current MC framework. The results of validation simulations show excellent agreement with …