Computer Sciences Commons^™

A Digitally Controlled Drive System For Travelling-Wave Ultrasonic Motor, Güngör Bal

Turkish Journal of Electrical Engineering and Computer Sciences

A digitally controlled drive system was implemented in this study to control the speed and direction of a travelling-wave ultrasonic motor. The drive system, based on a 2-phase voltage-fed high-frequency serial-resonant inverter, uses the mechanical resonant frequency of an ultrasonic motor. A TMS320F243 digital signal processor was used to control an ultrasonic motor drive system. The speed control of the ultrasonic motor was achieved with a driving frequency in the 41.3-43.3 kHz frequency range. The feasible evaluations of the proposed drive and control system were tested by experiments. Experimental results demonstrated that the proposed drive and control system is flexible …

A New Simulator For Hvdc/Ac Systems-Part I, Baktiar Zangeneh, Abbas Shoulaie

Turkish Journal of Electrical Engineering and Computer Sciences

A simulator with optimal step time (SOST) has been designed to investigate Large HVdc/ac systems. The adequacy and robustness of the simulator will be demonstrated by showing some important applications relevant to operation, operational planning and medium-term planing. Some of the features of our SOST simulator are optimal step time algorithm, interpolation, chatter removal, MATLAB interface, unlimited size of ac system, and Farsi command that help model complex power electronic circuits, provide fast and accurate results. On account of its reduced calculation effort and deterministic execution time, optimal-step simulation is a prerequisite for real-time performance. However, when simulating electromagnetic-transients behavior, …

Protocols For Disease Classification From Mass Spectrometry Data, Michael Wagner, Dayanand Naik, Alex Pothen

Mathematics & Statistics Faculty Publications

We report our results in classifying protein matrix-assisted laser desorption/ionizationtime of flight mass spectra obtained from serum samples into diseased and healthy groups. We discuss in detail five of the steps in preprocessing the mass spectral data for biomarker discovery, as well as our criterion for choosing a small set of peaks for classifying the samples. Cross-validation studies with four selected proteins yielded misclassification rates in the 10-15% range for all the classification methods. Three of these proteins or protein fragments are down-regulated and one up-regulated in lung cancer, the disease under consideration in this data set. When cross-validation studies …

Adaptive Critic Neural Network-Based Controller For Nonlinear Systems With Input Constraints, Pingan He, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

A novel adaptive critic-Based multilayer neural network (NN) controller in discrete-time is designed to deliver a desired tracking performance for a class of nonlinear systems in the presence of magnitude constraints on the input. Reinforcement learning scheme in discrete time is proposed for the NN controller, where the action generating NN learning is performed based on a certain performance measure, which is supplied from a critic. using the Lyapunov approach and with a novel weight update, the uniform ultimately boundedness (UUB) of the closed loop tracking error and weight estimates are shown. the adaptive critic NN does not require an …

Rate-Based End-To-End Congestion Control Of Multimedia Traffic In Packet Switched Networks, Mingsheng Peng, S. R. Subramanya, Jagannathan Sarangapani

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes an explicit rate-based end-to-end congestion control mechanism to alleviate congestion of multimedia traffic in packet switched networks such as the Internet. The congestion is controlled by adjusting the transmission rates of the sources in response to the feedback information from destination such as the buffer occupancy, packet arrival rate and service rate at the outgoing link, so that a desired quality of service (QoS) can be met. The QoS is defined in terms of packet loss ratio, transmission delay, power, and network utilization. Comparison studies demonstrate the effectiveness of the proposed scheme over New-Reno TCP (a variant …

An Analytical Model For Calculating Bounds On Call Blocking Probabilities In Leo Satellite Networks, A. Hali̇m Zai̇m

Turkish Journal of Electrical Engineering and Computer Sciences

We present an analytical model for calculating upper and lower bounds for call-blocking probabilities in a LEO satellite network that carries voice calls. The method is especially useful for large systems where calculation of call-blocking probabilities are too expensive. Our method calculates upper and lower bounds very easily and produces fairly accurate results.

Network Traffic Properties Of Bimodal Multicast Protocol, Öznur Özkasap, Mi̇ne Çağlar

Turkish Journal of Electrical Engineering and Computer Sciences

The popularity of large-scale distributed applications, such as videoconferencing, multimedia dissemination, electronic stock exchange and distributed cooperative work, has grown with the availability of high-speed networks and the expansion of the Internet. The key property of this type of applications is the need to distribute data among multiple participants together with an application-specific quality of service needs. This fact makes scalable multicast protocols an essential underlying communication structure. Although there exist several studies investigating the traffic characteristics of unicast communication, multicast traffic has not been examined extensively in previous studies. It is well known that the aggregate traffic properties of …

The \Mathcal{H}_\Infty Model Matching Problem With One Degree Of Freedom Static State Feedback, Murat Akin, Ati̇lla Bi̇r

Turkish Journal of Electrical Engineering and Computer Sciences

The aim of this paper is to develop a new approach for a solution of the continuous-time model matching problem by a static state feedback in the sense of \mathcal{H}_\infty optimality criterion by using Linear Matrix Inequalities (LMIs). The main contribution could briefly be described as to reformulate the model matching problem in LMI formulation, to present the solvability conditions and to give a design procedure for the one degree of freedom static state feedback control law. Finally, the results are applied to an example system.

New Approaches For On-Line Tuning Of The Linear Sliding Surface Slope In Sliding Mode Controllers, Sezai̇ Tokat, İbrahi̇m Eksi̇n, Müjde Güzelkaya

Turkish Journal of Electrical Engineering and Computer Sciences

The main objective of this study is to propose new approaches for on-line tuning of the linear sliding surface slope in sliding mode controllers. The new approaches are developed for a class of second order systems on new coordinate axes, one of which is the classical sliding surface and the other one is naturally chosen to be orthogonal to it. The control input of the sliding mode control law is then modified accordingly by applying the Lyapunov stability condition. The adjustment of the linear sliding surface slope defined in the new coordinate axes is achieved by tuning a new parameter …

Resonant Demagnetization Pwm Forward Converter, B. Bi̇lgi̇n, Işik Çadirci, R. Ergül, M. Ermi̇ş

Turkish Journal of Electrical Engineering and Computer Sciences

In this paper, a new approach to demagnetization process of a PWM forward converter (FC) is proposed. According to this approach, the demagnetization winding and diode of a conventional FC are removed, and an external capacitor is added in parallel with the secondary diode. This replacement changes the linear demagnetization process of a conventional FC into a resonant demagnetization process. The theoretical performance results of the proposed resonant demagnetization forward converter (RDFC) are compared with those of a conventional FC. A side by side comparison made between the two types of demagnetization strategies has shown that RDFC has some advantages …

Zero-Crossing Based Demodulation Of Minimum Shift Keying, Mi̇ne Kalkan, Feza Keresteci̇oğlu

Turkish Journal of Electrical Engineering and Computer Sciences

Minimum shift keying (MSK) modulation has features such as constant envelope, compact spectrum and good error performance, which are all desirable in many digital applications including mobile radio. Numerous receiver structures to demodulate MSK have been suggested, such as correlation receivers, differential detectors and frequency discriminators. MSK is a form of biphase keying and can be detected by a zero-crossing based phase demodulator which gives near optimum performance. In this paper, the bit error performance of a zero-crossing based coherent MSK demodulator is theoretically investigated and a closed-form expression for the bit error rate is derived. The results indicate that …

Music, Cbf And Differential Algebraic Constant Modulus Algorithms For Direction Of Arrival Estimation In Passive Coherent Locators, Ahmet Özçeti̇n

Turkish Journal of Electrical Engineering and Computer Sciences

In passive coherent locators (PCL) systems, noise and the precision of direction of arrival (DOA) estimation are key issues. This paper addresses the implementation of high-resolution DOA estimation methods, in particular the multiple signal classification (MUSIC) algorithm, the conventional beam forming (CBF) algorithm, and the algebraic constant modulus algorithm (ACMA). The goal is to compare the ACMA to the MUSIC and CBF algorithms for application to PCL. The results and analysis presented here support the use of constant modulus information, where available, as an important addition to DOA estimation. The ACMA offers many simple solutions to noise and separation related …

A Full Adaptive Observer For Dc Servo Motors, Ata Sevi̇nç

Turkish Journal of Electrical Engineering and Computer Sciences

An adaptive observer estimating all parameters and load torque is proposed for DC servo motors. The observer uses no direct feedback but the adaptation schemes use current and speed measurements. Both the observer and adaptations are simple to implement for real-time applications. Simulation results are satisfactory for the full adaptive observer. If the observer works in parallel with only load torque and armature resistance adaptations, the results are very good even if very low-quality sensors are used. In this simulation, only a single hall sensor is used as a rotational transducer, which produces a single pulse per revolution, and very …

New Infratechnologies In The Deregulated Power Sector, Jordan Shikoski, Vladimir Katic, Risto Rechkoski

Turkish Journal of Electrical Engineering and Computer Sciences

This paper discusses new infratechnologies in the deregulated power sector. Most measurement and standardization techniques can be viewed as infratechnology. Infratechnologies are technical tools, including the measurement of data, test methods, and practices and technique. Standardization requirements are related to the measurement requirement. Although the system operation and market transactions concern many import aspects, they are insupportable and often complementary. This distinction between the technical and market information is important because the characteristics of information needs and the impact on economic efficiency and clean power are generally different. The present paper focuses on infratechnologies that can potentially increase the benefits …

Design Of A Tem-Cell With Increased Usable Test Area, Kresimir Malaric, Juraj Bartolic

Turkish Journal of Electrical Engineering and Computer Sciences

Transversal electromagnetic mode cells (TEM-cells) are used for electromagnetic compatibility measurements (emission and immunity), and for biomedical applications. Over the years, higher and higher frequencies are being used, which demands smaller transmission structures in order to obtain the homogeneous field distribution due to resonance. Such resonance destroys the TEM field, introducing higher order modes. The goal was to design the TEM-cell for GSM frequencies that will have a larger area with a homogeneous field used for testing, while still obtaining the characteristic impedance. Commercial TEM-cells used for frequencies of 900 MHz have only 2 cm in height available for testing, …

A New Simulator For Hvdc/Ac Systems-Part Ii, Baktiar Zangeneh, Abbas Shoulaie

Turkish Journal of Electrical Engineering and Computer Sciences

This paper presents a performance comparison (the focus of numerical simulation) of traditional simulation (TCS,TSE) with an optimal step time simulator (SOST) for large HVdc systems.In SOST, a Detailed simulation of HVdc converter behavior has been modified to include the automatic selection of optimal integration steps, frequency-dependent effects of an ac system, ac system phase and magnitude dynamics of voltage (particularly weak ac systems), control assessment and temporary over-voltage consequences. SOST, via graphical interfaces,provides fast and accurate information of electromechanical and the electromagnetic-transients behavior of a large HVdc/HVac system.

Study Of Transport Properties Of Inas Using Monte Carlo Simulation, Satyanadh Gundimada

Electrical & Computer Engineering Theses & Dissertations

The present research is aimed at ascertaining the usefulness of InAs semiconductor material for single photon avalanche photo detectors operating in the Geiger mode at 2 μm wavelengths. InAs is considered as the material suitable for the purpose because of its less bandgap and lower effective mass of the electrons when compared to other semiconductor materials presently in use. Hence, theoretically transient transport properties of bulk InAs are superior and the velocity overshoot phenomena stronger. InAs is a relatively less explored material when compared to other materials like GaAs. The choice of the material is justified with thorough exploration of …

Yet Another Algorithm For Pitch Tracking (Yaapt), Kavita Kasi

Electrical & Computer Engineering Theses & Dissertations

This thesis presents a pitch detection algorithm that is extremely robust for both high quality and telephone speech. The kernel method for this algorithm is the Normalized Cross Correlation (NCCF) reported by David Talkin [16]. Major innovations include: processing of the original acoustic signal and a nonlinearly processed version of the signal to partially restore very weak F0 components; intelligent peak picking to select multiple F0 candidates and assign merit factors; and, incorporation of highly robust pitch contours obtained from smoothed versions of low frequency portions of spectrograms. Dynamic programming is used to find the ''best" pitch track among all …

On The Area Of Hypercube Layouts, Ronald I. Greenberg, Lee Guan

Computer Science: Faculty Publications and Other Works

This paper precisely analyzes the wire density and required area in standard styles for the hypercube. It shows that the most natural, regular layout of a hypercube of N^2 nodes in the plane, in a NxN grid arrangement, uses floor(2N/3)+1 horizontal wiring tracks for each row of nodes. (In the process, we see that the number of tracks per row can be reduced by 1 with a less regular design, as can also be seen from an independent argument of Bezrukov et al.) This paper also gives a simple formula for the wire density at any cut position and a …

Adaptive Predictive Congestion Control Of High-Speed Atm Networks, Sarangapani Jagannathan, Jayasree Talluri

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes an auto regressive moving average (ARMAX)-based adaptive control methodology to prevent congestion in high-speed asynchronous transfer mode (ATM) networks. Adaptive controller is developed to control traffic where sources adjust their transmission rates in response to the feedback information from the network switches. Specifically, the buffer dynamics at a given switch is modeled as a nonlinear discrete-time system and an ARMAX controller is designed so as to predict the explicit values of the transmission rates of the sources so as to prevent congestion. Tuning methods are provided for the unknown coefficients of the ARMAX model to estimate the …

A Formal Object Model For Layered Networks To Support Verification And Simulation, Rasha M. B. E. Morsi

Electrical & Computer Engineering Theses & Dissertations

This work presents an abstract formal model of the interconnection structure of the Open Systems Interconnection Reference Model (OSI-RM) developed using Object-Oriented modeling principles permitting it to serve as a re-usable platform in supporting the development of simulations and formal methods applied to layered network protocols. A simulation of the object model using MODSIM III was developed and Prototype Verification System (PVS) was used to show the applicability of the object model to formal methods by formally specifying and verifying a Global Systems for Mobile communications (GSM) protocol. This application has proved to be successful in two aspects. The first …

Robust Face Representation And Recognition Under Low Resolution And Difficult Lighting Conditions, Mohammad Moinul Islam

Electrical & Computer Engineering Theses & Dissertations

This dissertation focuses on different aspects of face image analysis for accurate face recognition under low resolution and poor lighting conditions. A novel resolution enhancement technique is proposed for enhancing a low resolution face image into a high resolution image for better visualization and improved feature extraction, especially in a video surveillance environment. This method performs kernel regression and component feature learning in local neighborhood of the face images. It uses directional Fourier phase feature component to adaptively lean the regression kernel based on local covariance to estimate the high resolution image. For each patch in the neighborhood, four directional …

Traffic Simulation Using Arena, Shanti Yelamanchi

Electrical & Computer Engineering Theses & Dissertations

Many traffic simulation tools exist for developing traffic simulations; these tools can be divided broadly into two categories — macro simulation tools and micro simulation tools. These two categories of simulation tools are directed at modeling the extremes of traffic systems: very large systems and very small systems. There is a class of intermediate-sized transportation networks for which neither category of simulation tools might perform adequately. Additionally these specialized traffic simulation tools have a high learning curve. For developing medium sized traffic simulations in a short period of time, one might choose to use a familiar general-purpose discrete event simulation …

Embedded Software Programming To Develop A Command Line User Interface For Monitoring And Debugging A Manually Driven Gas Regulator Control System, Syed N. Hyder

Electrical & Computer Engineering Theses & Dissertations

This thesis presents a complete embedded programming model and software codes for a command-line user interface for CONCOA's gas regulator control system. Control Corporation of America (CONCOA) manufactures high-pressure gas regulators, which mechanically control the pressure at their outlets. Since the control system is based on mechanical regulators, adding or stopping gas flow from the system can cause manifold fluctuation that could further cause the pressure to rise or fall with time. The main motivation for developing a command line user interface is to provide a centralized computer control to monitor and debug the gas regulator control system electronically by …

Translation And Rotation Invariant Multiscale Image Registration, Jennifer L. Manfra

Theses and Dissertations

The most recent research involved registering images in the presence of translations and rotations using one iteration of the redundant discrete wavelet transform. We extend this work by creating a new multiscale transform to register two images with translation or rotation differences, independent of scale differences between the images. Our two-dimensional multiscale transform uses an innovative combination of lowpass filtering and the continuous wavelet transform to mimic the two-dimensional redundant discrete wavelet transform. This allows us to obtain multiple subbands at various scales while maintaining the desirable properties of the redundant discrete wavelet transform. Whereas the discrete wavelet transform produces …

Cxquery: A Novel Xml Query Language, Peter Revesz, Yi Chen

School of Computing: Conference and Workshop Papers

XML is becoming the data exchange standard on the Internet. Previously proposed XML query languages, such as XQuery, Quilt, YALT, Lorel, and XML-QL, lack schema definition of the query result; therefore, they are limited for defining views, integrating data, updating, and further querying, all of which are often needed in e-Business applications. We propose a novel XML query language called CXQuery, which defines the schema of the query results explicitly and can easily define views, and integrate, update, and query XML data. In addition, CXQuery can express spatial and spatio-temporal queries using a constraint-based querying approach.

A Vhdl Implementation Of Bist Technique In Uart Design, Mohd. Yamani Idna Idris

Student Works (2000-2009)

No abstract provided.

Design And Analysis Of Radio Frequency Deployment Algorithms For Gsm, Mónica Pérez-Carbonell

Theses

Due to the growth of the subscriber base and the introduction of new services, mobile communications networks’ demand for wireless resources is increasing. This has resulted in an increasing need to change the frequency allocation of a network in order to adapt the cellular network to new frequency demands.

Currently, a planning tool generates a new frequency plan, which is. then deployed to cell sites. The deployment should ideally be carried out with minimum disruption to network operation, which makes this deployment process a critical undertaking as any errors during or after the deployment can leave the network with poor …

Distributed Power Control In Wireless Communication Systems, Sarangapani Jagannathan, A. T. Chronopoulos, S. Ponipireddy

Electrical and Computer Engineering Faculty Research & Creative Works

Energy efficiency is a measure of performance in wireless networks. Therefore, controlling the transmitter power at a given node increases not only battery operating life, but also overall system capacity by successfully admitting new links. It is essential to find effective means of power control in point-to-point, broadcasting and multicasting scenarios. Wireless networking presents formidable challenges, and we consider the problem of unicast or point-to-point (peer-to-peer) communication in wireless networks in the presence of other nodes. We study the feasibility of admitting new links in an wireless network operating area while maintaining quality of service (QoS), in terms of signal-to-interference …

Study Of Relative Effectiveness Of Features In Content-Based Image Retrieval, S. R. Subramanya, Jui Che Teng, Yongjian Fu

Electrical and Computer Engineering Faculty Research & Creative Works

Content-based retrieval in image databases requires appropriate features of images to be derived and used in the indexing and searching process. Fast and accurate retrieval is crucial from a user point of view. The kinds of features used, their organization in suitable data structures, and the similarity search scheme, directly affect the speed and quality of content-based retrieval. In this paper, we evaluate the relative significance of three different image features - geometry, moments, and Fourier descriptors in the context of content-based retrieval, and present experimental results. The evaluation metrics are retrieval quality and search time. These could be used …