Other Chemistry Commons^™

A Comparative Study Of Tin Electrorefining In Molten Licl–Kcl–Cacl₂: Experimental Two-Electrode Current Control And Theoretical Three-Electrode Potential Control, Bryant Johnson, George Ankrah, Ander Fuller, Devin Rappleye

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

Molten salt electrorefining is a mature technology for metal recovery, yet conventional current‑controlled, two‑electrode operation provides limited electrochemical selectivity and restricted insight into electrode‑specific behavior. In this work, a simplified model is developed to compare current‑controlled two‑electrode electrorefining data with a potential‑controlled three‑electrode electrorefining simulation using tin in molten LiCl–KCl–CaCl₂ as a surrogate for plutonium processing. The model examines anodic and cathodic limitations under fixed‑potential operation and evaluates implications for selectivity, efficiency, and runtime relative to experimentally demonstrated two‑electrode performance. Results indicate that independent potential control enables operation closer to thermodynamic selectivity limits, with the potential to suppress impurity oxidation …

Binary Solid/Liquid Equilibrium Of Mixtures Of Thermally Robust Salts And Molecular Compounds For Use As Heat Transfer Fluids, Jared Ridge Mathews

Honors Theses

Fossil fuels, contributors to climate change that may bear catastrophic consequences, power the entire world. The human species is almost entirely dependent on fossil fuels for energy, but other sources of renewable and environmentally friendly energy must be developed. Concentrated solar power (CSP) is a promising source of renewable energy with hampered potential—better heat transfer fluids (HTFs) are needed for it to be economically feasible. Currently, the HTFs in industrial use are predominantly either synthetic oils or nitrate-based molten salts. Synthetic oils are only stable up to 400 °C, and molten salts often have high melting temperatures, making them prone …

Effects Of Chain Length, Saturation, And Bases On Saponification, Sarah Fenik

Williams Honors College, Honors Research Projects

This project will analyze the effects of chain length and saturation of fatty acids on saponification processes, as well as the effects of the base used in the reaction. Stearic acid, lauric acid, and oleic acid will be used for the fatty acid comparisons, and sodium hydroxide and potassium hydroxide will be used for the base comparisons. Stearic acid is considered a long chain fatty acid, while lauric acid is considered a short chain fatty acid. Oleic acid is a monounsaturated fatty acid. Five soap products are be made: sodium stearate, sodium laurate, sodium oleate, potassium stearate, and potassium oleate. …

Investigating The Impact Of Secondary Activation Time On The Adsorption Properties Of Activated Biochar For Arsenic Removal From Wastewater, Achyuth Bharadwaj Rayarao

Graduate Theses and Dissertations (2019 - present)

Biochar, a naturally occurring and renewable carbon material, becomes porous through activation. Activated biochar is an ideal candidate for use as an adsorbent. The objective of this study is to investigate whether activated biochar derived from Colorado soft pine serves as a better adsorbent and demonstrates enhanced adsorption capabilities after undergoing secondary physical activation at various activation times. The effect of secondary action time on physical adsorption properties drawn from the analysis of isotherm plots, surface areas and pore size patterns were examined by using a physisorption analyzer. Chemical structures were identified using both ultimate and proximate analyses, while porosity …

Synergistic Effect Of Nanoclay And Barium Sulfate Fillers On The Corrosion Resistance Of Polyester Powder Coatings, Jinbao Huang, Marshall Shuai Yang, Chengqian Xian, James Joseph Noel, Yolanda S. Hedberg, Jian Chen, Ubong Eduok, Ivan Barker, Jeffrey Daniel Henderson, Haiping Zhang, Liqin Wang, Hui Zhang, Jesse Zhu

Chemistry Publications

No abstract provided.

Improved Performance Of Silica-Supported La0.5Ba0.5Feo3 In The Reverse Water Gas Shift - Chemical Looping Process For Carbon Dioxide Reduction – A Density Functional Theory Study, Jiawei Guo

USF Tampa Graduate Theses and Dissertations

Global warming is increasingly obvious, and the reduction of greenhouse gases is an effective way to heal. Increasing the efficiency of catalysts that is applied in the industry can significantly reduce the emission of greenhouse gases. Reverse water gas shift chemical looping (RWGS-CL) is a promising reaction to convert CO2 to CO. La0.5Ba0.5FeO3 (LBF) is a good candidate for RWGS-CL, which shows increased conversion yield when supported on silica. This research focuses on identifying the mechanism of RWGS-CL via silica-supported LBF by exploring the oxygen vacancy formation energy (EO-vac). Density Functional Theory (DFT) is a powerful computational method to solve …

Electrochemical Impedance Spectroscopy Analysis Of Corrosion Of Reinforcing Steel In Fly Ash Mortar By Means Of Transmission Line Modeling, Padraig Stack

Williams Honors College, Honors Research Projects

Electrochemical impedance spectroscopy (EIS) is an important non-destructive tool that allows for a deeper understanding of the electrochemical processes and mechanisms occurring in an electrochemical cell. Equivalent electrical circuits (EECs) are used to model the impedance data into electrical components, such as resistors and capacitors, on a circuit. Current potentiostat offers software packages that can analyze the frequency response, but the software only supports “simple” EEC that can be written as fixed electrical components in some combination of series and parallel. Park and Macdonald propose a transmission line model (TLM) that does not use lumped-element models, instead, the values of …

An Experimental And Numerical Investigation Of Flow Accelerated Flibe Corrosion, David B. Weitzel

Nuclear Engineering ETDs

Renewed interest in molten salt reactor technology has brought to light the need for a better understanding of FLiBe corrosion. To this end a flowing FLiBe corrosion test loop was designed to test the flow effects of FLiBe corrosion. The loop consists of a pump, melt tank, and stainless-steel tubing assembly that heats the molten salt to high temperatures and circulates it over test specimens. The experiment has been constructed and has completed initial shakedown testing.

To support the flowing FLiBe experiment, a numerical corrosion model that couples FLiBe electrochemistry, solid metal diffusion, and mass transport was implemented. The model …

Feco2o4 As An Anode Material For Lithium Ion Batteries, Chelsea Wong

The International Student Science Fair 2018

Lithium ion batteries (LIBs) are commonly found in many portable electronic appliances due to their ability to be rechargeable. Currently, commercial anodes in Li-ion batteries (graphite) have a theoretical capacity of around 372 mAh/g, while FeCo2O4 that will be investigated as the anode material has a theoretical capacity of 901.985mAh/g, more than double of the current commercial anode’s capacity. Earlier work done by Sharma et al also showed that FeCo2O4 has a very promising initial capacity of 827mAh/g. As such, the engineering goal is to produce a battery that will have a higher capacity than the current commercial Li-ion batteries …

Feco2o4 As An Anode Material For Lithium Ion Batteries, Chelsea Wong

The International Student Science Fair 2018

Lithium ion batteries (LIBs) are commonly found in many portable electronic appliances due to their ability to be rechargeable. Currently, commercial anodes in Li-ion batteries (graphite) have a theoretical capacity of around 372 mAh/g, while FeCo2O4 that will be investigated as the anode material has a theoretical capacity of 901.985mAh/g, more than double of the current commercial anode’s capacity. Earlier work done by Sharma et al also showed that FeCo2O4 has a very promising initial capacity of 827mAh/g. As such, the engineering goal is to produce a battery that will have a higher capacity than the current commercial Li-ion batteries …

Surfactant Driven Assembly Of Freeze-Casted, Polymer-Derived Ceramic Nanoparticles On Grapehene Oxide Sheets For Lithium-Ion Battery Anodes, Ali Zein Khater

Honors Undergraduate Theses

Traditional Lithium-Ion Batteries (LIBs) are a reliable and cost-efficient choice for energy storage. LIBs offer high energy density and low self-discharge. Recent developments in electric-based technologies push for replacing historically used Lead-Acid batteries with LIBs. However, LIBs do not yet meet the demands of modern technology. Silicon and graphene oxide (GO) have been identified as promising replacements to improve anode materials. Graphene oxide has a unique sheet-like structure that provides a mechanically stable, light weight material for LIB anodes. Due to its structure, reduced graphene oxide (rGO) is efficiently conductive and resistive to environmental changes. On the other hand, silicon-based …

Technical Feasibility Of Selectively Separating Rare Earth Elements By Vapor Phase Extraction And Condensation, Katie Lyons

Graduate Theses & Non-Theses

Experiments were performed to evaluate the technical feasibility of selectively separating selected rare earth halides (bromides and chlorides) using a volatilization and condensation technique. Initially, optimum chloridizing and bromidizing roast parameters were secured in studies performed on reagent grade rare earth oxide samples and subsequently confirmed in tests performed on mineral ore and concentrate samples. The volatilization and condensation experiments were performed by placing the subject rare earth halide samples in an argon-purged multiple-zone tube furnace wherein the temperature profile was controlled to establish separate vaporization and condensation regions. Following each experiment, condensate and solid residue samples were analyzed to …

Computational Optimization And Characterization Of Molecularly Imprinted Polymers, Jacob Jordan Terracina

Legacy Theses & Dissertations (2009 - 2024)

Molecularly imprinted polymers (MIPs) are a class of materials containing sites capable of selectively binding to the imprinted target molecule. Computational chemistry techniques were used to study the effect of different fabrication parameters (the monomer-to-target ratios, pre-polymerization solvent, temperature, and pH) on the formation of the MIP binding sites. Imprinted binding sites were built in silico for the purposes of better characterizing the receptor – ligand interactions. Chiefly, the sites were characterized with respect to their selectivities and the heterogeneity between sites.

Gc Verification Of The Spacecraft Atmosphere Monitor, Jessica S. Castro, Richard D. Kidd, Jeffrey D. Hein

STAR Program Research Presentations

International Space Station crew members face the unique challenge of maintaining air quality due to the volatile organic compounds (VOCs) that have the potential to accumulate at unsafe levels. The Spacecraft Atmosphere Monitor (SAM) is a miniature gas chromatograph/mass spectrometer (GCMS) designed to measure major constituents (such as N₂, O₂ and CO₂) and trace VOCs within the cabin of the spacecraft. The gas chromatograph is responsible for separating the sample into its components in order to be characterized. The oven of the gas chromatograph must reach a temperature of 150°C in order to heat constituents …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

A Modified Surface On Titanium Deposited By A Blasting Process, Caroline O' Sullivan, Peter O'Hare, Greg Byrne, Liam O'Neill, Katie B. Ryan, Abina M. Crean

Publications

Abstract

: Hydroxyapatite (HA) coating of hard tissue implants is widely employed for its biocompatible and osteoconductive properties as well as its improved mechanical properties. Plasma technology is the principal deposition process for coating HA on bioactive metals for this application. However, thermal decomposition of HA can occur during the plasma deposition process, resulting in coating variability in terms of purity, uniformity and crystallinity, which can lead to implant failure caused by aseptic loosening. In this study, CoBlast™, a novel blasting process has been used to successfully modify a titanium (V) substrate with a HA treatment using a dopant/abrasive regime. …