Materials Chemistry Commons^™

Effects Of Ti Addition On The Characteristics Of Al-10zn-6mg-2si/Zro2 Composites Produced By Squeeze Casting, Qesha Diva Prameshvara, Pipin Indah Lestari, Bondan Tiara Sofyan

Journal of Materials Exploration and Findings

Metal matrix composite (MMC) with 7xxx aluminum matrix is potential for ballistic applications due to the combination of strength, toughness, and light weight. Previous study successfully produced aluminum-based composites with SiC particles which were able to stop type III bullet, however cracks remained on back of the plate. Therefore, in this research, SiC was replaced by zirconia (ZrO₂) due to its high fracture toughness. Ti-B grain refiner was added to further improve toughness through grain boundary strengthening mechanism. This research developed 5 vol.% ZrO₂ strengthened Al-10Zn-6Mg-2Si composite with addition of Al-5Ti-1B grain refiner produced through squeeze casting …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Excellent Bifunctional Oxygen Evolution And Reduction Electrocatalysts (5a1/5)Co2o4 And Their Tunability, Xin Wang, Harish Singh, Manashi Nath, Kurt Lagemann, Katharine Page

Chemistry Faculty Research & Creative Works

Hastening the Progress of Rechargeable Metal-Air Batteries and Hydrogen Fuel Cells Necessitates the Advancement of Economically Feasible, Earth-Abundant, Inexpensive, and Efficient Electrocatalysts Facilitating Both the Oxygen Evolution Reaction (OER) and Oxygen Reduction Reaction (ORR). Herein, a Recently Reported Family of Nano (5A1/5) Co2O4 (A = Combinations of Transition Metals, Mg, Mn, Fe, Ni, Cu, and Zn) Compositionally Complex Oxides (CCOs) [Wang Et Al., Chemistry of Materials, 2023, 35 (17), 7283-7291.] Are Studied as Bifunctional OER and ORR Electrocatalysts. among the Different Low-Temperature Soft-Templating Samples, Those Subjected to 600 °C Post annealing Heat Treatment Exhibit Superior Performance in Alkaline Media. One …

Probing The Surface Structure Of Ferrocene Modified Electrodes Using Cyclic Voltammetry, Rebekah S. Stanley

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

Modifying electrodes imparts new electrochemical properties for use in various applications. To fully understand these electrochemical properties the structure of the modified surface needs to be characterized. Cyclic voltammetry (CV) offers a quick and simple way to determine if the surface structure has been homogeneously modified even at low surface concentrations. Nonideal responses in CV scans give insights to the microenvironments and structure of the monolayer surface that may be indistinguishable in other techniques. Peak fitting CV data, coupled with other surface techniques, can further characterize the contributions and nature of these microenvironments and aid in structural determination.

Melting Point Predictions Of Thermally Stable Ionic Liquids Using A Machine Learning Approach, Jarod Morris

Poster Presentations

Thermally robust ionic liquids hold promise as high-temperature solvents, heat transfer fluids, and high-performance lubricants. These ionic liquids, inspired by thermoplastics like PEEK and PES, incorporate peraryl functional groups that lend them high thermal stability, however they often have melting points greater than 100 °C. A broad liquid range is usually desirable in most applications, so finding thermally robust ILs with lower melting points would significantly enhance their applicability. In this study, machine learning models are developed to make predictions of melting points for these thermally stable ionic liquids using a process called quantitative structure-property relationships (QSPR). The methodology used …

The Effects Of Free Volume And Processing On The Development Of Gas Separation Membranes, Jacob Schekman

Dissertations

Structure, thermal, mechanical, gas transport, and free volume properties of thiol-ene based systems are investigated and discussed. In the pursuit of generating low energy-cost polymer membranes for gas separation, it became apparent that UV-curing of thiol-ene materials presented several routes toward achieving this goal. Network structure plays a vital role in determining the gas transport properties of membrane materials. UV photopolymerization techniques provide a means to rapidly vitrify network morphologies which can be tuned depending on choice of monomer. Thiol-ene monomers offer a broad range of precursor materials from which to choose for the design of functional membrane materials.

Chapter …

The Synthesis And Characterization Of 9,10-Bis-(Iodoethynyl)Anthracene For 2d Molecular Crystals From Halogen-Bonding, Nehemiah Antoine

Honors Theses

Two-dimensional crystals have unique properties, giving them the potential to develop practical items such as electronics, biomedicine, and sensors. Our goal is to use chemical principles to synthesize molecules that spontaneously form 2D crystals with designed patterns and properties. For this, we will exploit directional, non-covalent interactions to determine what pattern will form in 2D. In this project halogen-bonding will be utilized: halogen-bonding is the interaction between the electrophilic region of a halogen and a nucleophilic region of a Lewis base. We are functionalizing anthracenes with iodine and nitrogen to form halogen bonds that enable the molecules to pack more …

Magnetic Properties Of Zgnrs With Nitrogen And Fluorine Adsorbates, A Computational Study, Justin Petit

Electronic Theses and Dissertations

Imposing dimensional restrictions on graphene sheets and adding impurities can give rise to carbon nanostructures with magnetic properties. In this work, zigzag graphene nanoribbons, zGNRs, with nitrogen and fluorine adatoms are investigated for magnetic properties of interest for spin devices. Geometry optimizations were done determining which position along a zGNR electrode that N and F would favorably attach to. Edge positions were determined as the most stable attachment site. M-cell zGNR electrodes (M = 1-3) edge-functionalized by N and F adatoms were investigated with respect to their band structures and spin densities in antiferromagnetic and ferromagnetic, AFM and FM, configurations. …

Conversion Of Microcrystalline Cellulose To Hexane Using Hydrogenated Metal Oxides At Low Temperature And Pressure, Mubarak Osman

Electronic Theses and Dissertations

Increasing global energy demand and environmental concerns have fueled the exploration of sustainable and efficient methods for renewable fuel production. The conversion of cellulosic waste to hydrocarbon fuels using hydrogenated metal oxides presents a novel and eco-friendly approach to sustainably address energy demand. In this study, hydrogenated metal oxides were used as catalysts in a relatively low-temperature and atmospheric-pressure environment to facilitate the conversion of cellulosic waste into hydrocarbon fuels. Hydrogenated metal oxides have been introduced as potential hydrogen transfer catalysts. The expected result is the selective conversion of cellulose to hexane at relatively low temperatures, which significantly reduces energy …

Synthesis, Electrical Conductivity, Electrocatalytic Activity For Water Splitting, And Pseudocapacitive Properties Of Perovskite Oxide Derivatives., Kinithi Meththa Kumari Wickramaratne

Electronic Theses and Dissertations

Developing green and sustainable energy solutions is crucial to addressing the energy and environmental challenges. Hydrogen is an attractive candidate given its high energy density and low carbon emission compared to gasoline and coal. Electrochemical water splitting through a water electrolyzer is recognized as a green method for generating hydrogen and oxygen gases. Developing cost-effective electrocatalysts to reduce overpotential in hydrogen and oxygen generation is essential for the overall process. The growing interest in perovskite oxides as versatile and sustainable catalysts is driven by their compositional flexibility, tunable electronic structure, earth abundance, and inherent catalytic performance. In our research, we …

Revealing The Three-Dimensional Arrangement Of Polar Topology In Nanoparticles, Chaewa Jeong, Juhyeok Lee, Hyesung Jo, Jaewhan Oh, Hionsuck Baik, Kyoung-June Go, Junwoo Son, Si-Young Choi, Sergey Prosandeev, Laurent Bellaiche, Yongsoo Yang

Physics Faculty Publications and Presentations

In the early 2000s, low dimensional ferroelectric systems were predicted to have topologically nontrivial polar structures, such as vortices or skyrmions, depending on mechanical or electrical boundary conditions. A few variants of these structures have been experimentally observed in thin film model systems, where they are engineered by balancing electrostatic charge and elastic distortion energies. However, the measurement and classification of topological textures for general ferroelectric nanostructures have remained elusive, as it requires mapping the local polarization at the atomic scale in three dimensions. Here we unveil topological polar structures in ferroelectric BaTiO₃ nanoparticles via atomic electron tomography, which …

Structure-Property Relationship Studies Of Electrically Conductive Metal-Organic Framework Materials, Shiyu Zhang

All Dissertations

Electrically conductive metal-organic frameworks (EC-MOFs) are among the most promising materials due to their tunable structures, properties, and diverse functions. However, the lack of comprehensive understanding of their structure-property relationship hinders the development of EC-MOFs. My dissertation focuses on the design, construction, and structure-property relationship studies of EC-MOFs.

Chapter 1 describes how MOFs' structural features and compositions affect the electronic properties and demonstrates conductive mechanisms and the corresponding design strategies to develop EC-MOFs.

Chapter 2 describes the synthesis, characterization, electronic and optical properties of four novel alkali-metal-based (Na, K, Rb, and Cs) 3D-MOFs with continuous tetrathiafulvalene tetracarboxylate (TTFTC) π-stacks, systematicly …

Carbon "Quantum" Dots: Structures, Properties, And Issues, Weixiong Liang

All Dissertations

Carbon dots (CDots) are small carbon nanoparticles (CNPs) with effective surface passivation. The effective passivation has been achieved by the surface functionalization of pre-existing CNPs with organic molecules, mostly molecules containing primary or secondary amine moieties. In the studies highlighted in this dissertation, CNPs were functionalized by selected organic molecules, including especially the use of radical addition reactions, to generate CDots with strong absorption and bright fluorescence emissions. A good demonstration of the approach was the N-ethylcarbazole (NEC) radical addition to CNPs under microwave irradiation. Spectroscopy and microscopy methods were employed to characterize the resulting NEC-CDots, and the results …

Bridging The Gap Between Molecular Components And Functional Electronic Chemical Sensing Devices With 2d Layered, Conductive Metal–Organic Frameworks, Emma Katherine Ambrogi

Dartmouth College Ph.D Dissertations

Layered, conductive framework materials are a class of materials with properties that make them ideal sensing materials in electronic chemical sensors. My thesis is focused on the development of these materials for electrochemical sensing of liquid phase analytes, and on understanding the material–analyte and material–electrode interfaces, and their self-assembly and deposition onto surfaces.

Chapter 1 provides a summary of the use of layered conductive metal–organic frameworks (MOFs) and covalent organic frameworks (COFs) in electronic chemical sensors, detailing the materials and sensor architectures employed, and the analytes detected. Relevant performance metrics are compared, and investigations into material–analyte interactions are highlighted.

Chapter …

Electrocatalytic Cyclopropanation Of Active Methylene Compounds, Liang-Hua Jie, Hai-Chao Xu

Journal of Electrochemistry

The development of novel strategies to access cyclopropanes has become increasingly important due to the vital role of these three-membered ring structures in synthetic intermediates, natural products, and pharmaceuticals. Herein, we present an electrocatalytic method for the synthesis of cyclopropanes through intermolecular dehydrogenative annulation of active methylene compounds and arylalkenes. This electrochemical process requires no chemical oxidants, allowing for a speedy access to various functionalized cyclopropanes from inexpensive and readily available materials.

Electrochemical Syntheses Of Aryl-Substituted Benzothiophenes And Phenanthrenes Using Benzenediazonium Salts As The Aryl Radical Precursors, Li-Yuan Lan, Yang-Ye Jiang, Raymond Daniel Little, Cheng-Chu Zeng

Journal of Electrochemistry

Aryl-substituted benzothiophene and phenanthrene are important structural units in medicinal chemistry and materials science. Although extensive effort has been devoted to prepare these compounds and a variety of approaches have been developed to construct the 2-substituted benzothiophene core structure, environmental-friendly and efficient synthetic means are still desired. Based on our previous electrochemical Minisci-type arylation reaction with aryl diazonium salt as the aryl precursor, as well as the work from König’s group, herein, we described the use of paired electrolysis to achieve 2-aryl benzothiophenes and 9-aryl phenanthrenes employing benzenediazonium salts as the aryl radical precursors. Initially, 2-methylthiobenzendiazonium salt 1a and 4-methylbenzene …

Electrochemical Advanced Treatment Of Desulfurization Wastewater From Coal-Fired Power Plants, Ju-Cai Wei, Juan Yi, Xu Wu

Journal of Electrochemistry

Zero-emission of desulfurization wastewater is one of the main demands for coal-fired power plants. As typical high salinity wastewater, it is hard to purify the desulfurization wastewater from coal-fired power plants through traditional physicochemical treatment or biochemical treatment, e.g., COD and Cl^–. A high concentration of Cl^– ion in desulfurization wastewater restricts wastewater reuse and zero-emission. Electrochemical technology is an attractive method for high salinity wastewater zero-emission, which provides a versatile, efficient, cost-effective, easily automatable, and clean industrial process. For advanced treatment of effluent after triple box process treatment in power plants, this paper reports an electrochemical …

Seeding Effects Of Submicron Caal-No3 Ldh Particles On The Hydration And Properties Of Portland Cement And Sulfoaluminate Cement Pastes, Sukanta K. Mondal, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Layered double hydroxide (LDH) is reported to improve the durability of concretes, primarily due to its ability to exchange anionic species, including chloride, which is implicated in corrosion-driven durability issues. However, there is no comprehensive study investigating the effect of LDH on the properties of different cement systems at both early and mature ages. in this study, the early age and mature age properties of Portland cement (OPC) and calcium sulfoaluminate (CSA) cement pastes seeded with submicron-sized calcium aluminum-NO3 LDH (CaAl-NO3 LDH) were investigated. the effects of the 1–5%mass dosage of LDH on the hydration of both cement systems were …

Thermal Frontal Polymerization – Applications In Coatings And Composites, Maria Martinez

LSU Doctoral Dissertations

Thermal frontal polymerization has long been used as a method to cure composites and coatings. However, this is the first time these applications have been used without the use of a catalyst, for the case of composites and coatings.

Chapter 2 discusses how to optimize cure-on-demand, thin layer coatings, using frontal polymerization. Previously, for the use of curing thin layer coating using thermal FP, it was known to just make the formulation viscous enough, as this would prevent premature quenching caused by heat loss. It was discovered that for a given layer thickness, a minimum viscosity and initiator concentration were …

Group Iv Topological Quantum Alloy And The Role Of Short-Range Order: The Case Of Ge-Rich Ge1–XPbX, Yunfan Liang, Shunda Chen, Xiaochen Jin, Damien West, Shui-Qing Yu, Tianshu Li, Shengbai Zhang

Electrical Engineering and Computer Science Faculty Publications and Presentations

Despite the explosion of interest in topological materials over the last decades, their applications remain limited due to challenges in growth and incorporation with today’s microelectronics. As a potential bridge to close this gap, we investigate the group-IV alloy Ge_1–xPb_x, in the Ge-rich condition using density functional theory and show that relatively low concentrations of Pb (~9.4%) can lead to a topological phase transition. Furthermore, the calculation of the Z₂ invariant for both the random alloy and the alloy with short-range order (SRO) indicate that the topological phase of the material can be directly modified …

Shorting At Long Duration: Impact Of Extended Discharge Capacity On Battery Solid Electrolytes, Ryan C. Hill, Amanda S. Peretti, Leo J. Small, Erik D. Spoerke, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110 ° C were cycled at 0.1 A cm−2 for 1–23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. …

Synthesis, Molecular Characteristics, And Antibacterial Assessment Of Marine Hydroid Aqueous Extract-Based Silver Bio-Nanoparticles, Fredryk Mandey, Aulia Rhamdani Arfan, Rugaiyah Andi Arfah

Makara Journal of Science

This investigation aims to synthesize, analyze the molecularity, and test the ability of bacterial inhibition capability of silver nanoparticles that have been synthesized by simply mixing silver nitrate and aqueous extracts of marine natural products with and without the addition of amylum as a stabilizing agent. This research, with and without the addition of amylum as a stabilizing agent, obtained 39.0 and 55.2 mg of solids of round-shaped morphology silver nanoparticles with diameters of 87.9 and 103.0 nm., respectively. In addition, the antibacterial testing assay against Staphylococcus aureus and Escherichia coli showed some considerably good results. S. aureus with the …

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …

Micropatterning And Functionalization Of Single Layer Graphene: Tuning Its Electron Transport Properties, Miao-Miao Cui, Lian-Huan Han, Lan-Ping Zeng, Jia-Yao Guo, Wei-Ying Song, Chuan Liu, Yuan-Fei Wu, Shi-Yi Luo, Yun-Hua Liu, Dong-Ping Zhan

Journal of Electrochemistry

As a promising 2D material, graphene exhibits excellent physical properties including single-atom-scale thickness and remarkably high charge carrier mobility. However, its semi-metallic nature with a zero bandgap poses challenges for its application in high-performance field-effect transistors (FETs). In order to overcome these limitations, various approaches have been explored to modulate graphene's bandgap, including nanoscale confinement, external field induction, doping, and chemical micropatterning. Nevertheless, the stability and controllability still need to be improved. In this study, we propose a feasible method that combines electrochemical bromination and photolithography to precisely tune the electron transport properties of single layer graphene (SLG). Through this …

New Ways To Improve Dispersibility Of Nanotubes: Approaching From The Formation Of Silicon Nanoparticles By High Energy Reactive Ball Milling (Herbm) In Polar Solvents, Julie P. Vanegas, Yolanda V. Gutierrez, Joaquin Rivera, Juan García Jr.

Research Symposium

Background: This research aims to synthesize stable silicon nanoparticles using different molar ratios of N-Cyclohexyl-2-pyrrolidone (CHP) and Silicon to demonstrate if there is any significance towards the production of effective nanotubes. To determine this, the synthesized nanoparticles will be characterized by scanning electron microscopy (SEM), UV visible absorption spectroscopy, and photoluminescence spectroscopy (PL).

Methods: 50 Mg of silicon wafer are added with differing ratios of ligand (CHP), 5mL of water, and 3 steel iron balls into a ball milling vial. Vials are then placed into a ball milling apparatus for 7 cycles or 3.5 hours. Once the cycles are complete, …

Highly Efficient Dopamine Sensing With A Carbon Nanotube-Encapsulated Metal Chalcogenide Nanostructure, Harish Singh, Jiandong Wu, Kurt A.L. Lagemann, Manashi Nath

Chemical and Biochemical Engineering Faculty Research & Creative Works

Carbon nanotube-encapsulated nickel selenide composite nanostructures were used as nonenzymatic electrochemical sensors for dopamine detection. These composite nanostructures were synthesized through a simple, one-step, and environmentally friendly chemical vapor deposition method, wherein the CNTs were formed in situ from pyrolysis of a carbon-rich metallo-organic precursor. The composition and morphology of these hybrid NiSe2-filled carbon nanostructures were confirmed by powder X-ray diffraction, Raman, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy images. Electrochemical tests demonstrated that the as-synthesized hybrid nanostructures exhibited outstanding electrocatalytic performance toward dopamine oxidation, with a high sensitivity of 19.62 μA μM-1 cm-2, low detection limit, broad linear …

Joint Time-Frequency Analysis: Taking Charge Penetration Depth And Current Spatial Distribution In The Single Pore As An Example, Nan Wang, Qiu-An Huang, Wei-Heng Li, Yu-Xuan Bai, Jiu-Jun Zhang

Journal of Electrochemistry

In recent years, joint time-frequency analysis has once again become a research hotspot. Supercapacitors have high power density and long service life, however, in order to balance between power density and energy density, two key factors need to be considered: (i) the specific surface area of the porous matrix; (ii) the electrolyte accessibility to the intra-pore space of porous carbon matrix. Electrochemical impedance spectra are extensively used to investigate charge penetration ratio and charge storage mechanism in the porous electrode for capacitance energy storage. Furthermore, similar results could be obtained by different methods such as stable-state analysis in the frequency …

Automated Workflow For Redox Potentials And Acidity Constants Calculations From Machine Learning Molecular Dynamics, Feng Wang, Jun Cheng

Journal of Electrochemistry

Redox potentials and acidity constants are key properties for evaluating the performance of energy materials. To achieve computational design of new generation of energy materials with higher performances, computing redox potentials and acidity constants with computational chemistry have attracted lots of attention. However, many works are done by using implicit solvation models, which is difficult to be applied to complex solvation environments due to hard parameterization. Recently, ab initio molecular dynamics (AIMD) has been applied to investigate real electrolytes with complex solvation. Furthermore, AIMD based free energy calculation methods have been established to calculate these physical chemical properties accurately. However, …

Measurements Of Rate Constant For Electrode Reactions, Lian-Huan Han, Jia-Yao Guo, Miao-Miao Cui

Journal of Electrochemistry

Standard electron-transfer rate constant is one of the intrinsic properties for an electrochemical reaction, which is significant in the study of electrode kinetics. It is a key criterion for one to clarify the mechanism and pathway of a specific electrochemical reaction, and to screening and design the electrocatalysts and battery materials. Herein, we will introduce the measuring methods of rate constant for electrode reactions, including polarization curve, rotating disk electrode, ultramicroelectrode, scanning electrochemical microscopy, electrochemical impedance spectroscopy, current step, potential step and cyclic voltammetry, etc., to provide a guide to investigate electrode kinetics for graduate students and researchers in the …

Mesoporous Re0.5ce0.5o2-X Fluorite Electrocatalysts For The Oxygen Evolution Reaction, Sreya Paladugu, Ibrahim Munkaila Abdullahi, Harish Singh, Sam Spinuzzi, Manashi Nath, Katharine Page

Chemistry Faculty Research & Creative Works

Developing highly active and stable electrocatalysts for the oxygen evolution reaction (OER) is key to improving the efficiency and practical application of various sustainable energy technologies including water electrolysis, CO₂ reduction, and metal air batteries. Here, we use evaporation-induced self-assembly (EISA) to synthesize highly porous fluorite nanocatalysts with a high surface area. In this study, we demonstrate that a 50% rare-earth cation substitution for Ce in the CeO₂ fluorite lattice improves the OER activity and stability by introducing oxygen vacancies into the host lattice, which results in a decrease in the adsorption energy of the OH* intermediate in …