Materials Chemistry Commons^™

Single-Step Synthesis Of Activated Carbon From Arabica Spent Coffee Ground Using K2co3 As Activator Agent, Ghina Ivana Mieldan, Yuliusman Yuliusman

Journal of Materials Exploration and Findings

Activated carbon is a nanomaterial that is often used as an effective adsorbent. Activated carbon raw materials can use biomass, such as coffee grounds, which can be found along with the growth of public interest in coffee drinks. Chemical activators are used for activation to increase biomass carbon's adsorption capacity. Using K₂CO₃ activator to increase the specific surface area of activated carbon is more harmless than KOH. The use of spent coffee grounds as carbon source and food additive K₂CO₃ as an activator can make food-grade activated carbon that can be used for food. …

Effect Of Alkyd And Polyester Resin Compositions On Corrosion Resistance, Blistering, And Adhesion In Utilization Of Oily Sludge As Anti-Rust Coating Material, Gerets Land Kakalang, Yohanes David Kristianto, Johny Wahyuadi Mudaryoto

Journal of Materials Exploration and Findings

Oil sludge is a waste derived from upstream and downstream activities of the oil and gas industry which is estimated at 10,000 tonnes generated from all PERTAMINA downstream activities spread across various fields, processing units and depots throughout Indonesia. Oil sludge has the same characteristics as asphalt, where asphalt in previous studies can be used as an anti-rust coating, so that the handling of oily sludge can be topped up by reusing and having its own added value. The purpose of this research is to utilise waste oily sludge as an alternative anti-rust coating material and compare alkyd resin and …

Dendrite-Free Strategies For Aqueous Zinc-Ion Batteries: Structure, Electrolyte, And Separator, Gang Wu, Wu-Hai Yang, Yang Yang, Hui-Jun Yang

Journal of Electrochemistry

Continued growth in energy demand and increased environmental pollution constitute major challenges that need to be addressed urgently. The development and utilization of renewable, sustainable, and clean energy sources, such as wind and solar, are crucial. However, the instability of these intermittent energy sources makes the need for energy storage systems increasingly urgent. Aqueous zinc-ion batteries (AZIBs) have received widespread attention due to their unique advantages, such as high energy density, cost-effectiveness, environmental friendliness, and safety. However, AZIBs face significant challenges, mainly the formation of zinc dendrites that seriously affect the stability and lifetime of the batteries, leading to battery …

All-Solid-State Sodium-Ion Batteries: A Leading Contender In The Next-Generation Battery Race, Rui-Jie Zhu, Ze-Chen Li, Wei Zhang, Akira Nasu, Hiroaki Kobayashi, Masaki Matsui

Journal of Electrochemistry

All-solid-state lithium-ion batteries (LIBs) using ceramic electrolytes are considered the ideal form of rechargeable batteries due to their high energy density and safety. However, in the pursuit of all-solid-state LIBs, the issue of lithium resource availability is selectively overlooked. Considering that the amount of lithium required for all-solid-state LIBs is not sustainable with current lithium resources, another system that also offers the dual advantages of high energy density and safety— all-solid-state sodium-ion batteries (SIBs) —holds significant sustainable advantages and is likely to be the strong contender in the competition for developing next-generation high-energy-density batteries. This article briefly introduces the research …

Contributions To Journal Of Electrochemistry, The Flagship Journal Of Chinese Chemical Society Electrochemical Committee, Will Be Listed As A New Recommendation Policy For China Youth Awards Of Electrochemist, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Electrochemical-Method-Induced Strong Metal-Support Interaction In Pt-Cnt@Sno2 For Co-Tolerant Hydrogen Oxidation Reaction, Shen-Zhou Li, Zi-Jie Lin, Qi-An Chen, Zhao Cai, Qing Li

Journal of Electrochemistry

Inducing the classic strong metal-support interaction (SMSI) is an effective approach to enhance the performance of supported metal catalysts by encapsulating the metal nanoparticles (NPs) with supports. Conventional thermal reduction method for inducing SMSI processes is often accompanied by undesirable structural evolution of metal NPs. In this study, a mild electrochemical method has been developed as a new approach to induce SMSI, using the cable structured core@shell CNT@SnO₂ loaded Pt NPs as a proof of concept. The induced SnO_x encapsulation layer on the surface of Pt NPs can protect Pt NPs from the poisoned of CO impurity in …

Development Of Methods For Predicting Second Harmonic Generation (Shg) Responses Of New Infrared Nonlinear Optical (Ir-Nlo) Materials, Katherine Colbaugh

Electronic Theses and Dissertations

Dissertation supervised by Dr. Jennifer A. Aitken.

In this work, calculations-based methods were evaluated for use in prediction of second harmonic generation (SHG), specifically χ⁽²⁾ values, of infrared nonlinear optical (IR-NLO) materials. Net dipole moment and dipole moment per volume were calculated by the bond valence sum method. Average F-index, proposed in this research, and group F-index, both representing induced dipole moment were also calculated. Each calculation was evaluated by comparing the results to single crystal and powder χ⁽²⁾ measurements of IR-NLO materials. The selected dataset consisted of ninety-six compounds including polar and nonpolar structures, newly discovered and …

Developing A Method To Identify Tyre Particles By Detecting Benzothiazole Via Gc-Ms, Emma Paull

The Plymouth Student Scientist

Tyre particles are a dominant source of microplastic pollution in our environment. However, their chemical and physical properties are poorly understood and no standardised methods for identifying and quantifying them exist. This study looked to develop a method to identify tyre particles using two tyre samples of differing particle sizes, fine (62 - 125 µm) and coarse (250 – 500 µm). Both samples underwent ultrasound-assisted extraction before being analysed via gas chromatography-mass spectrometry (GC-MS) in both full scan and SIM mode, using benzothiazole as a marker. Both samples were also analysed via particle size analysis, scanning electron microscopy (SEM) and …

Analysis Of Dense Metals Accumulation In Shikaripara Stone Mines, Gopinath Gorai, Nirajan Kumar Mandal

Makara Journal of Science

This study aimed to measure the amount of dangerous substances in the cultivated area of the Shikaripara stone mines in Jharkhand, India, which are well known for their stone quarrying. Sixteen soil samples were collected at varying dis-tances from the Shikaripara stone mines in the Dumka District of Jharkhand. The metals found in these samples in-clude Pb, As, Zn, Mn, Cd, Cu, Fg, and Fe. The combined amount of the elements was calculated by inductively coupled plasma mass spectrometry. Enrichment factor, accumulation index, contamination factor, pollution load index (PLI), Nemerow index, and ecological risk index (RI) were employed to assess …

Physical Properties Of Aqueous Imide-Based Electrolyte Solutions, Mollie Harr

Honors Capstones

In order to observe the effects that cations have on the physical properties of -TFSI [-bis(trifluoromethane sulfonyl)imide] based salts, four salts (LiTFSI, NaTFSI, Mg(TFSI)2, and Al(TFSI)3) were selected for testing. The data gathered shows that when the anion is large and bulky like -TFSI, the size of the cation does not have a large effect on the physical properties, but the oxidation state of the cation may have a significant effect. The ion-ion interactions, such as collisions, aggregation, and repulsion are more significant when the cation has a higher oxidation state due to the increased ratio of anion per molecule …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-Based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO₂, MoS₂, and Al₂O₃) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment …

Fitting Quality Of Nmr Relaxation Data To Differentiate Asphalt Binders, Rebecca M. Herndon, Kevin Lai, Magdy Abdelrahman, Klaus Woelk

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Asphalt binder performance grades (PGs) are important metrics in designing pavements for effective transportation infrastructure. the PG system relies on the binder's stiffness and is determined through energy- and time-intensive physical testing. Physical properties, like stiffness, can also be determined by spin–lattice NMR relaxometry, a non-destructive chemical method. NMR relaxometry can quantify the molecular mobility of materials by determining relaxation times from exponential decays of excited nuclear magnetization. While relaxation times have been used to determine physical properties of materials, a quantitative relation to the PG grades of asphalt binder is yet to be established. in this study, T1 NMR …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO2, MoS2, and Al2O3) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment of 10 °C. Obtained results showed that thermal …

Experimental Evaluation Of A Recrosslinkable Co2-Resistant Micro-Sized Preformed Particle Gel For Co2 Sweep Efficiency Improvement In Reservoirs With Super-K Channels, Adel Alotibi, Tao Song, Ali Al Brahim, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A recross linkable CO₂-resistant branched preformed particle gel (CO₂-BRPPG) was developed for controlling CO₂ injection conformance, particularly in reservoirs with super-permeable channels. Previous work focused on a millimeter-sized CO₂-BRPPG in open fractures, but its performance in high-permeability channels with pore throat networks remained unexplored. This study used a sand pack model to evaluate a micro-sized CO₂-BRPPG under varying conditions of salinity, gel concentration, and pH. at ambient conditions, the equilibrium swelling ratio (ESR) of the gel reached 76 times its original size. This ratio decreased with increasing salinity but remained stable …

Understanding Defect Dynamics In Black Phosphorene Under Noble Gas Ion Irradiation., Saransh Gupta

Electronic Theses and Dissertations

Controlled introduction of defects in phosphorene using high-energy ion beams offers a promising route to design novel high-performance materials for energy technologies. However, this potential remains underexplored due to a lack of fundamental understanding of the atomic-scale mechanisms governing the production, accumulation, and temporal evolution of defects during ion irradiation. Here, we employ a combination of classical and ab initio molecular dynamics simulations to elucidate the effects of ion energy, angle of incidence, noble gas ion size/mass, and fluence on (a) defect generation (i.e., point defects, topological imperfections, voids), (b) atomic-scale mechanisms of defect formation and re-arrangement, and (c) defect …

Nickel Electrocatalysts On Carbon Supports For The Hydrogen Evolution Reaction., Mohan Paudel

Electronic Theses and Dissertations

Hydrogen is an important energy storage alternative to fossil fuels due to its high energy density. Currently, most hydrogen is produced through petroleum feedstocks, which produce large amounts of carbon dioxide. However, a more eco-friendly method is the electrocatalytic splitting of water into hydrogen and oxygen. Efficient catalysts for the hydrogen evolution reaction (HER) are typically platinum group metals, which are rare and expensive. There is growing interest in developing HER electrocatalysts with earth-abundant metals for water electrolysis. Nickel, which lies in the same group in the periodic table as Pt and has similar chemical properties, is explored extensively for …

Medium-Entropy Engineering Of Magnetism In Layered Antiferromagnet CuXNi2(1-X)CrXP2S6, Dinesh Upreti, Rabindra Basnet, M. M. Sharma, Santosh Karki Chhetri, Gokul Acharya, Md Rafique Un Nabi, Joshua Sakon, Mourad Benamara, Mansour Mortazavi, Jin Hu

Physics Faculty Publications and Presentations

Antiferromagnetic van der Waals-type M₂P₂X₆ compounds provide a versatile material platform for studying 2D magnetism and relevant phenomena. Establishing ferromagnetism in 2D materials is technologically valuable. Though magnetism is generally tunable via a chemical way, it is challenging to induce ferromagnetism with isovalent chalcogen and bimetallic substitutions in M₂P₂X₆. Here, we report co-substitution of Cu¹⁺ and Cr³⁺ for Ni²⁺ in Ni₂P₂S₆, creating Cu_xNi_2(1-x)Cr_xP₂S₆ medium-entropy alloys spanning a full substitution range ( …

Hydrothermal Synthesis, Characterisation, And Magnetic Study Of First-Row Transition Metal Molybdates And First-Row Transition Metal Vanadates, Mahsa Foroughian Foroughian

All Dissertations

Growing high-quality single crystals of transitional metal oxides have been of interest over the last two centuries because of the many applications of these transparent materials in various industries, such as optics, magnetism, semiconductors, and batteries. During this period, a variety of crystal growth techniques have been utilized, each offering unique advantages and disadvantages to the solid-state community.

Traditionally, metal oxides such as molybdates and vanadates are produced using high-temperature techniques (700 to 1200 °C). These methods can cause oxygen to be expelled, resulting in the creation of lattice defects and lower-valence metal ions and complicate precise measurements of physical …

Recyclable Composites Prepared From Animal Coproducts And Industrial Waste Sulfur, Perla Y. Sauceda-Oloño

All Dissertations

Pursuing sustainable and environmentally friendly materials has become a significant objective in materials science, particularly flame retardants and construction materials. This dissertation explores the development and evaluation of novel composites and high sulfur-content materials (HSMs) as potential alternatives to conventional, environmentally harmful materials.

Chapter one reviews recent advancements in environmentally benign flame-retardant additives, highlighting the potential of bio-derived phenols, polysaccharide derivatives, and greener phosphorus sources. The review discusses how green additives can enhance the flame retardancy, thermal stability, and smoke suppression properties of various polymers while addressing the challenges and future directions in the field.

Chapter two investigates the production …

Author Spotlight, Li-Fang Yang, Joseph W. Sampson, Xiao-Hang Sun, Hai-Qiang Deng, He Zhang, Md Maksudur Rahman, Yang Tao, Hang Ren

Journal of Electrochemistry

No abstract provided.

Single-Entity Collisional Electrochemistry At The Micro- And/Or Nano-Interface Between Two Immiscible Electrolyte Solutions, Li-Fang Yang, Jun-Jie Chen, Ling-Yu Chen, Si-Qi Jin, Tao-Xiong Fang, Si-Jia He, Liang-Jun Shen, Xin-Jian Huang, Xiao-Hang Sun, Hai-Qiang Deng

Journal of Electrochemistry

Single-entity collisional electrochemistry (SECE) is a branch of single-entity electrochemistry. It can directly characterize entities/particles with single particle resolution through random collisions between particles and electrodes in a solution, and obtain rich physicochemical information, thus becoming one of the frontiers of electroanalytical chemistry in the past two decades. Interestingly, the (micro/nanoscale) sensing electrodes have evolved from a polarizable liquid/ liquid (mercury/liquid) interface to a solid/liquid interface and then to a liquid/liquid interface (i.e., an interface between two immiscible electrolyte solutions, ITIES), as if they have completed a cycle (but in fact they have not). ITIES has become the latest sensing …

Precision Delivery Using Nanopipette For Single-Cell Studies, He Zhang, Maksudur Rahman, Yang Tao, Joseph W Sampson, Hang Ren

Journal of Electrochemistry

Nanopipette based scanning probe technique is a versatile tool in non-contact imaging in biology. In addition to the topographic imaging, its capability of localized delivery of bio-active molecules is emerging. In this mini review, we introduce the applications of nanopipette in single-cell researches with a focus on localized delivery. The working principles of three delivery modes including resistive pulse, pressure-driven flow, and electroosmotic flow-driven delivery are summarized and compared. Their applications in single-cell researches are reviewed. The current technical challenges in scanning ion conductance microscopy-based delivery, and their growing influence in medicine and pharmacologic researches are also discussed.

Aqueous Supercapacitors With Wide Operative Voltage Window And Long Cycling Life Enabled By Electrolyte Hybridization Effect, Shi-Hua Ma, Qi Yin, Jin-Ping Zhao

Journal of Electrochemistry

Developing supercapacitors (SCs) with long cycling life and wide operative voltage window is a significant topic in the field of aqueous electrolytes. Although the design of water in salt (WIS) electrolytes has pushed the development of aqueous electrolytes to a new height, the WIS electrolytes with an operative voltage window of up to 2.5 V is still very scarce. Herein, in order to enrich the type of aqueous electrolyte with high operative voltage, tetramethylammonium trifluoromethanesulfonate (TMAOTf) based WIS electrolyte was used as a model to construct WIS based hybrid electrolyte with acetonitrile (ACN) co-solvent and LiTFSI co-solute. In view of …

Journal Of Electrochemistry, The Flagship Journal Of Chinese Chemical Society Electrochemical Committee, Made A Public Appearance At The 22nd National Electrochemical Congress, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

The Award Ceremony Of The 2nd Xiamen University Short Video Abstract Contest For Science And Technology Journal Papers Came To A Successful Conclusion, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

The 9th National Conference Of Solid State Battery Successfully Held In Xiamen, Fujian, Zheng-Liang Gong

Journal of Electrochemistry

No abstract provided.

Multiphase Electrochemical Li-Ion Intercalation In Iron Selenite: Evidence Of Fe³⁺/⁴⁺ Redox And Single-Crystal-To-Single-Crystal Topochemical Transformation During Chemical Lithiation, Sutapa Bhattacharya, Aleksandr V. Chernatynskiy, Amitava Choudhury

Physics Faculty Research & Creative Works

An iron selenite-based cathode compound, LiFe(SeO₃)₂, is synthesized via a simple hydrothermal route. The bulk purity of the compound is confirmed by powder X-ray diffraction (PXRD), Mössbauer spectroscopy, and Fourier transform infrared spectroscopy (FTIR). The crystal structure determined from the single-crystal X-ray diffraction and Rietveld refinement of synchrotron PXRD data perfectly matches the previously reported structure in the I4̅2d space group. The crystal structure is built up of edge-sharing of FeO₆ octahedra and LiO₄ tetrahedra interconnected by SeO₃ trigonal pyramidal units, forming a three-dimensional open framework network with channels through all three axes. …

Novel Nanocomposite Of Carbonized Chitosan-Zinc Oxide-Magnetite For Adsorption Of Toxic Elements From Aqueous Solutions, Dalia A. Ali Eng, Ganna Gaber Ismail Eng.

Chemical Engineering

Herein, a novel nanocomposite (carbonized chitosan-zinc oxide-magnetite, CCZF) was developed to effectively remove toxic elements in water remediation. Combining the high adsorption capacities of chitosan with the magnetic properties of magnetite and the chemical stability of zinc oxide, the combination of these unique properties makes it an efficient and versatile material that offers a sustainable solution for water purification. The (CCZF) nanocomposite was synthesized through the coprecipitation method and characterized using various techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET) analysis, X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and zeta potential analysis. The results showed …

Highly Sensitive Detection Of Strontium Ions Using Metal-Organic Frameworks Functionalized Solid-State Nanochannels, Xu-Gang Wang, Zheng-Xu He, De-Fang Ding, Xue-Qin Luo, Li Dai, Wei-Qi Zhang, Qun Ma, Yu Huang, Fan Xia

Journal of Electrochemistry

Strontium-90, a highly radioactive isotope, accumulates within the food chain and skeletal structure, posing significant risks to human health. There is a critical need for a sensitive detection strategy for Strontium-90 in complex environmental samples. Here, solid-state nanochannels, modified with metal-organic frameworks (MOF) and specific aptamers, were engineered for highly sensitive detection of strontium ion (Sr²⁺). The synergistic effect between the reduced effective diameter of the nanochannels due to MOF and the specific binding of Sr²⁺ by aptamers amplifies the difference in ionic current signals, enhancing detection sensitivity significantly. The MOF-modified nanochannels exhibit highly sensitive detection of …

Single Nanobubble Formation On Au Nanoelectrodes And Au@Ws2 Nanoelectrodes: Voltammetric Analysis And Electrocatalysis, Xian-Zhun Luo, Xiao-Hu Chen, Yong-Xin Li

Journal of Electrochemistry

Taking advantage of the extremely small size of the gold nanodisk electrode, the single hydrogen nanobubble generated on the surface of the nanoelectrode was studied to evaluate its hydrogen evolution performance. It was found that compared with the bare gold nanodisk electrode, the bubble formation potential of the gold nanodisk electrode modified with tungsten disulfide quantum dots (WS₂ QDs) on the surface was more positive, indicating that its hydrogen evolution activity was higher. Microdynamic model analysis shows that the average standard rate constant of the rate-determining step of the hydrogen evolution reaction of gold nanoelectrodes modified with WS_{2 …}