Materials Chemistry Commons^™

Coulometric-Weighing Test Method And Its Application In Determination Of Tin Coating Mass For Electrolytic Tinplate, Xiu-Wen Dong, Yan Li, Jian-Guo Liu, Guo-Wei Lin

Journal of Electrochemistry

The coulometric-weighing test method was established and applied to determine the tin coating mass for electrolytic timplate. The effects of electric quantity, the current efficiency and the electrochemical equivalent in the coulometric test method were overcome. The inaccuracy in the determination of final point at the anodic dissolution curve in the weighing method was avoided when applied to the electrolytic timplate, higher accuracy was obtained, the SD is less than 0.04 g/m²,RSD is as small as 0.36%.

Electrochemical Character Of Water Containing Gel Electrolyte And Its Preliminary Examination In Lithium Water Cell, Jing-Dong Liu, Wen-Ji Wang, Xin-Zheng Yi

Journal of Electrochemistry

AC impedance technique has been used to characterize the system of poly(methyl acrylic acid)-poly(methyl acrylic lithiumate)-glycerol (referred to as GPE).The results showed that the conductivity of GPE increased with increasing both temperature and its water content.The glass transition temperature of GPE polymer could be lowered by water. Its conducting characteristic was just like liquid electrolyte,The electrolysis of GPE was almost the same as the electrolysis of water. Its composition voltage was about 1.50V. The GPE has been used to manufacture lithium water cell. When the graphite was used as cathode, the cell could discharge continuously for 2 hours under constant …

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian

Journal of Electrochemistry

The monocrystalline metal nanowire arrays were prepared by using a two-step AC electrodeposition in porous anodic aluminum oxide (AAO) template. The growth mechanism of nanowires was discussed. As a result, it has been found that the second voltage pulse has a considerable effect on the pore-filling ratio, the uniformity and the crystal structure, whereas the initial voltage pulse affects only the pore-filling ratio. Using the two-step AC electrodeposition, a highly ordered monocrystalline metal nanowire arrays with a pore-filling ration above 95% can be easily obtained.

The Interaction In Doping Lithium Of Carbonaneous Anode In Lithium Ion Battery, Chang-Guo Chen, Hong-Min Zhang, Jia Chen, Dan-Mei Yu

Journal of Electrochemistry

The quantum chemical DV-X_α method was used to calculate the lithium-doped models from one-Li-dopant to LiC₆ and LiC₂. It was found that Li⁺ has an tendency to attract electrons from the carbon plane through the C₆ hexagons lying above or below it by the graph of charge-density difference. It was shown that LiC₆ can exist steadily,while LiC₂ can not exist steadily.

Study On Determination Of Iodine Ion At Chitosan Modified Glassy Carbon Electrode, Bin Liu, Xiang-Ying Sun, Jin-Rui Xu

Journal of Electrochemistry

In this paper, a chitosan modified glassy carbon electrode was prepared by the method of covalent-bond reaction, and the anodic stripping voltammetric characteristics of iodine on the modified electrode was studied. The results showed that the modified electrode has higher adsorption and selectivity for I^- , and the sensitivity for I^-  has been much improved in 0.1 mol·L^-1 KH₂PO₄ solution (pH=4.0). The anodic stripping peak current of I^- on the modified electrode varied linearly with I^-  concentration in the range of 2.0×10^-6～2.0×10^-3 mol·L^-1, and the detection limit …

Formation And Characterization Of Water-Repellent Nano Tio2 Coating And Studying Its Anticorrosion Property, Guang-Xia Shen, Yi-Cong Chen, Chang-Jian Lin

Journal of Electrochemistry

Using ethyl acetoacetate (EAcAc) as a chelating agent, ultra fine TiO₂ sol is prepared. Nano-TiO₂ coatings are deposited on the 316L stainless steel by the dip-coating. Hydrothermal post-treatment leads to crack-free coatings. Meanwhile, the surface struture and properties was optimized. Self-assembly of Hetadecafluorodecyltrimethoxysilane (FSA-13) fabricates hydrophobic layers on the surface of the nano-TiO₂ coatings. Particle sizes of TiO₂ sol was analysed by zeta pals potential analysis, and surface morphology, structure and properties was characterized by contract angle instrument, XRD, and SEM technologies. The results have shown that the surface of coatings is porous, with approx. 375 …

Study Of Electrochemical Properties Of The Hydride Alloy Electrode Zrcr0.4Mn0.2V0.1Co0.1Ni1.2 At High Temperature, Song Li, Shi-Jun Ji, Jun-Cai Sun

Journal of Electrochemistry

Electrochemical properties of the hydride alloy electrode ZrCr_0.4Mn_0.2V_0.1Co_0.1Ni_1.2 at the different temperature have been investigated. The results showed that the alloy electrodes possessed the maximum discharge capacities 336 mAh/g and 298 mAh/g at 25 ℃ and 70 ℃ respectively. The activation process of the alloy at 70 ℃ became faster, and the alloy reached its maximum capacity in less than 4 cycles, while in 13 cycles at 25 ℃. The high rate capability increased from 55 % at 25 ℃ to 71% at 70 ℃ at 300 mA/g. It was worth …

Electrochemical Synthesis Of Ferrate(Vi) By Anodic Oxidation, Jia-Ju Xu, Jian-Ming Wang, Wei-Hua Yang, Cheng Chen, Jian-Qing Zhang

Journal of Electrochemistry

The ferrate(Ⅵ) was synthesized by electrochemical anodic oxidation. The effects of preparation conditions on the current yield of ferrate(VI) synthesis have been studied in this work. The experimental results showed that grey cast iron as an anodic material is suitable for electrochemical synthesis and NaOH solution as an electrolyte results in a higher current yield than KOH solution. The highest current yield was obtained at a current density (4.54) mA·cm^-2, temperature 20 ℃ and 14 mol·dm^-3 NaOH. In this case, a current yield of 68.5% was obtained by electrolysis for 1 h.

Electrodeposition Nanolaminated Growth Of Zinc, Ying Cao, Tian-Hui Shen, Jing-Yuan Yao, Gui-Fu Ding

Journal of Electrochemistry

Nanolaminated growth of the electrodeposition of zinc was studied. The structure and size of crystalline in zinc coatings were investigated by using FEG-TEM and XRD. The corrosion tests of the zinc deposition and the Coatings-Neutral salt spray test were performed, the capability in corrosion resistance of the nanolaminated growth was better than that of others.

The Activity Of Silicon Carbide Particles In Al-Based Metal Matrix Composites Revealed By Scanning Electrochemical Microscopy, David O. Wipf, L. Díaz-Ballote, L. Veleva, M. A. Pech-Canul, M. I. Pech-Canul

CAS Publications

Scanning electrochemical microscopy (SECM) is used to image variations in electrochemical activity over the surface of an aluminum-based metal matrix composite (MMC) in contact with buffered or unbuffered neutral solutions. The composite consists of an Al - 13.5% Si - 9% Mg alloy matrix and reinforcing silicon carbide particles (SiC_p). Feedback mode SECM imaging using ferrocenemethanol as a redox mediator in 0.1 M NaCl solution and in buffer solution (pH 6.8) revealed that the SiC particles are electrochemically active. The data suggest that the electronic conductivity at these sites is higher than that of the Al₂O …

Ac Frequency Dependence Of Electroluminescent Zns Phosphor Panel Color, Farrah Shantell Boggess-Machado

Theses, Dissertations and Capstones

In this study, electroluminescent panels manufactured by Meadow River Enterprises were used to study the AC frequency dependence of their color. A project was developed to acquire their emittance color at various frequencies. Three frequencies were selected for the investigation. Data, obtained by measuring the spectrum at a constant excitation frequency, were taken for each of the three standard frequencies: 200 Hz, 1500 Hz, and 20 kHz. In general the higher the frequency, the bluer the emittance color of the panel. The lower the frequency, the more green the panel became. An explanation for this phenomenon, the frequency dependence of …

Chemical Vapor Deposited Diamond Films For Self-Referencing Fiber Optic Raman Probes [Erratum], Sacharia Albin, Jainli Zheng, Bing Xiao, John B. Cooper, Robert B. Jeffers, Sonia Antony

Chemistry & Biochemistry Faculty Publications

No abstract provided.

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

There is an active international interest in lead-bismuth eutectic and similar liquid lead systems because of the relevance to the transmutation of nuclear waste, fast reactors, and spallation neutron sources. A successful program in nuclear waste processing that includes transmutation in accelerator-driven systems and fast reactors, would significantly decrease the space requirements for geological repositories.

Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge because the corrosive behaviors of materials in LBE are not well understood. Most of the available information …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of environmental and mechanical parameters on environment induced degradations of candidate target structural materials for applications in spallation-neutron-target systems, such as accelerator-driven systems for the transmutation of waste. The materials selected for evaluation and characterization are martensitic stainless steels including Alloys HT-9, EP-823 and Type 422 stainless steel (SS).

More recently, this experimental program has been expanded to evaluate the effect of molten lead-bismuth eutectic (LBE) on the corrosion behavior of target structural materials in the presence of oxygen. Since the Materials Performance Laboratory (MPL) at UNLV currently cannot …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The corrosion of structural materials is a major concern for the use of lead-bismuth eutectic (LBE) systems for nuclear applications such as in transmuter targets or fast reactors. Corrosion in liquid metal systems can occur through various processes, including, for example, dissolution, formation of inter-metallic compounds at the interface, and penetration of liquid metal along grain boundaries. Predicting the rate of these processes depends on numerous system operational factors: temperature, system geometry, thermal gradients, solid and liquid compositions, and velocity of the liquid metal, to name a few. Corrosion, along with mechanical and/or hydraulic factors, often contributes to component failure. …