Materials Chemistry Commons^™

Kinetic Study Of Photoelectrochemical Oxidation Of Lignin Model Compounds On Tio2 Nanotubes, Min Tian, Daniel Liba, Aicheng Chen

Journal of Electrochemistry

In this study, TiO₂ nanotubes were prepared via the electrochemical oxidation of titanium substrates in a non-aqueous electrolyte and their morphology and microstructures were examined by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The photoelectrochemical oxidation of two lignin model compounds, 1-(3,4-dimethoxyphenoxy)-2-(2-methoxyphenoxy)-1,3-propanediol (DMP) and 3-hydroxy-1-(3,4-dimethoxyphenoxy)-2-(2-methoxyphenoxy)-1,3-propanone (HDM), was investigated. A new band appeared at ~304 nm during the photoelectrochemical oxidation of DMP. The rate of DMP intermediate formation was amplified with the increase of initial concentrations, while it was diminished with increased temperature. Despite the similarity in structure between HDM and DMP, there are only small increases in absorbance …

Electrochemical Synthesis Of Silver-Tetracyanoquinodimethane Nanorods At Agar Supported Water/1,2-Dichloroethane Interface, Li Huang, Yixian Wang, Michael V. Mirkin, Bin Ren, Dongping Zhan

Journal of Electrochemistry

Silver-tetracyanoquinodimethane (AgTCNQ) is an important charge transfer salt due to its high conductivity and other electronic properties. In this communication, we report the synthesis of AgTCNQ at the liquid/liquid interface. Agar was used as a gelling agent to support water/1,2-dichloroethane (DCE) interface. Silver ions were transferred from the hydrogel into DCE phase, where they combined with TCNQ^- to form AgTCNQ nanorods. The developed method can provide a new route for synthesis of functional materials based on the electrochemistry at the liquid/liquid interface.

Underpotential Deposition Of Copper On Pt(S)[N(100)X(110)] Stepped Surfaces, Gisbert Rubn, Climent Vctor, Herrero Enrique, M. Feliu Juan

Journal of Electrochemistry

The underpotential deposition of Cu on platinum stepped surfaces composed of (100) terraces and (110) monoatomic steps has been studied in different acidic solutions. It has been found that the initial stage of copper deposition on the surface takes place simultaneously on terrace and step sites, irrespective of the nature of the adsorbing anion. During the voltammetric deposition of a full monolayer, several peaks can be observed. The analysis of the dependence of the peak charge with the step density allows assigning the different peaks to different deposition sites. The peak appearing at most positive potentials corresponds to the deposition …

In Situ Pm-Irras Studies Of A Floating Bilayer Lipid Membrane At Au(111) Electrode Surface, Su Zhangfei, Kycia Annia, Jay Leitch J., Lipkowski Jacek

Journal of Electrochemistry

In situ Polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS) was used to study the structure of a DMPC + cholesterol + GM1 floating bilayer lipid membrane (fBLM) at a Au(111) surface. 1-thio-beta-D-glucose (beta-Tg) was self-assembled onto the Au electrode to increase the overall hydrophilicity of the surface. The fBLM was deposited on the beta-Tg self-assembled monolayer (SAM) using a combination of Langmuir-Blodgett/Langmuir-Schaefer (LB/LS) techniques. The carbohydrate headgroups of the GM1 molecules were physically adsorbed to the beta-Tg SAM forming a water rich cushion between the fBLM and the modified gold substrate. The PM-IRRAS spectra indicate that the DMPC molecules within …

The Oxidation Of Hydrogen Peroxide On Nanostructured Rhodium Microelectrodes, N. Bartlett Philip, F. Esterle Thomas

Journal of Electrochemistry

Mesoporous Rh films were deposited onto platinum microelectrodes from the H₁ lyotropic liquid crystalline phase of C₁₂EO₈ (octaethyleneglycol monododecyl ether). The electrodes show well defined voltammetry for the oxidation and the reduction of hydrogen peroxide at low concentrations (<10 mmol•L-1) with excellent stability for operation at neutral pH. Based on the hysteresis in the current and the potential dependence the oxidation of hydrogen peroxide occurs through a CEE mechanism involving Rh(OH)₃ on the mesoporous Rh electrode surface. At higher hydrogen peroxide concentrations the current reaches a plateau that is due to either saturation of the binding sites for hydrogen peroxide or limitation of the reaction due to acidification of the solution within the pores. For the thin films (below 200 nm) the hydrogen peroxide calibration curves we …

Electrochemical Sensing Of Guanine And Adenine Based On The Boron-Doped Carbon Nanotubes Modified Electrode, Ya-Lin Xia, Chun-Yan Deng, Juan Xiang

Journal of Electrochemistry

In this work, the boron-doped carbon nanotubes (BCNTs) modified glassy carbon (GC) electrode was simply fabricated, and the electrochemical oxidation behaviors of guanine and adenine at the BCNTs/GC electrode were investigated. Compared with the bare GC and CNTs/GC electrodes, the BCNTs-modified electrode exhibited extraordinary electrocatalytic activity towards the oxidations of guanine and adenine as indicated by the obvious increase in current responses. Moreover, the peak separation between guanine and adenine was large enough for their potential recognition in mixture without any separation or pretreatment. Therefore, the simultaneous determination of guanine and adenine was successfully achieved. The BCNTs/GC electrode showed high …

Naf-M (M = Fe, Cu) Nanocomposites As Conversion Cathode Materials For Sodium Ion Batteries, Ting Li, Zhong-Xue Chen, Yu-Liang Cao, Han-Xi Yang

Journal of Electrochemistry

The NaF-M (M = Fe, Cu) nanocomposites were prepared by high-energy ball milling using TiN grinding nanoparticles and investigated as cathode materials for sodium ion batteries. The experimental results demonstrated that NaF-Fe and NaF-Cu nanocomposites can go through electrochemical conversion reaction with Na⁺ uptake or removal, delivering a reversible capacity of ~ 150 mAh·g^-1, even through a reversed conversion from initial discharged state to a charged state. These results reveal the possibility to realize a conversion reaction as long as NaF and elemental metal particles are intimately contacted to form active nanocomposites at nanodomain, which suggests a …

Carbon Nanotubes With Ni2P Nanoparticles As A Counter Electrode In Dye-Sensitized Solar Cells, Yan-Ye Dou, Nan-Fu Yan, Guo-Ran Li, Xue-Ping Gao

Journal of Electrochemistry

Carbon nanotubes (CNTs) supported by Ni₂P nanoparticles are prepared and used as a counter electrode in dye-sensitized solar cells (DSSCs) for the first time. The CNTs-Ni₂P composite was prepared by the heat treatment of a mixed precursor including nickel chloride, sodium hypophosphite and CNTs in argon atmosphere. The X-Ray diffraction (XRD) results indicate that the as-prepared sample consists of hexagonal Ni2P and carbon nanotubes. No peaks of other nickel phosphides are observed in the XRD pattern. Microstructure of the Ni₂P-CNTs composite was investigated using transmission electron microscopy (TEM). It is shown that the Ni …

Electrochemical Performances Of Layered Polypyrrole/Chemically Reduced Graphene Oxide Nanocomposites As Supercapacitor Electrodes, Si-Zhe Xu, Xue-Jiao Zhou, Kun Wu, Yong-Qiang Yang, Hai-Xia Wu

Journal of Electrochemistry

Nanocomposites of polypyrrole (Ppy) and chemically reduced graphene oxide (CRGO), Ppy/CRGO, have been fabricated through in-situ polymerization of pyrrole on graphene oxide (GO) sheets. The as-synthesized Ppy/CRGO composites were characterized complementarily using scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Fourier transformed infrared spectroscopy (FT-IR). By controlling the initial ratio of the GO to pyrrole, the layered composites could be obtained and their thickness could be tuned properly. The Ppy/CRGO electrodes were prepared using a mechanical compressing technique and their electrical conductivity and electrochemical properties were characterized systematically. We demonstrated that as electrodes for supercapacitor, the Ppy/CRGO composites with Ppy …

Electrochemical Corrosion And Protection Of Copper Foil Treated By Surface Siloxane Filming, Wei-Jun Miao, Yu-Bao Zhang, Ning-Yu Gu, Feng Liu

Journal of Electrochemistry

Copper foil specimens were immersed in hydro-alcoholic solution of 3-amino-propyl-trimethoxy-silane (γ-APS) to prepare a protective self-assembled siloxane membrane on the surface. Potentiodynamic polarization and electrochemical impedance spectroscopic tests were performed in 0.1 mol.L^-1 NaCl to evaluate the effects of the self-assembled siloxane membranes prepared at different pH of γ-APS on corrosion of copper foil. The surface morphology of siloxane membrane was studied by SEM. Experimental results revealed that the γ-APS self-assembled siloxane membranes effectively inhibited the corrosion of copper foil and the optimum anti-corrosion effect was found when the pH value of the silane solution was 7.

Preparation And Electrochemical Performance Of Tio2/Gns Nanocomposite As Anode Materials For Lithium-Ion Batteries, Lin-Lin Qin, Huan Zhang, Xiao-Jing Liu, Jian-Hui Xu, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The honeycomb-like porous TiO₂/graphenes (TiO₂/GNs) nanocomposite was prepared by a reflux method. SEM and TEM results showed that nanosized anatase TiO₂ (about 5~10 nm) were dispersed uniformly on the surface of the GNs. The TiO₂/GNs composite showed excellent rate and cycling performance: A stable charge capacity of 169.5 mAh·g^-1 was obtained at 30C, and can restore to 241.7 mAh·g^-1 while current went back to 1C. The stable charge capacity of TiO₂/GNs nanocomposite electrode up to 201.9 mAh·g^-1 was achieved at 10C in the first cycle, and could be …

Preparation And Characterization Of Prussian Blue Modified Nanoelectrode, Wei Wang, Bao-Fa Su, Dong-Ping Zhan

Journal of Electrochemistry

The Pt nanoelectrodes were fabricated by using a laser-based pipet puller and the recessed nanoelectrodes were prepared by etching of disk Pt nanoelectrodes wtih high frequency ac voltage. Prussian blue microcrystal was synthesized electrochemically on the both disk and recessed Pt nanoelectrodes. The strength of mechanical adhesion for the Prussian blue microcrystal on the nanoelectrode was enhanced. A novel method for the controllable synthesis of single particle is proposed, which has potential applications in modified electrodes and single particle electrocatalysis.

Detection Of Pml/Rarî± Fusion Gene Using Gold Nanopaticles Modified Electrode By Chronocoulometry, Li-Man Wang, Li-Qing Lin, Shao-Huang Weng, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A gold nanoparticles modified electrode was prepared by electrodeposition at constant potential. The sulfydryl modified probe was immobilized onto surface of gold nanoparticles via Au-S covalent bond and hybridized with complementary target DNA sequences, then the DNA sensor was fabricated for the detection of PML/RARα fusion gene by chronocoulometry in acute promyelocytic leukemia (APL). Scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) were used to characterize the surface morphology of gold nanoparticles and the constructing process of sensor. With hexaammineruthenium(Ⅲ) chloride (RuHex) as a novel electrochemical indicator, the chronocoulometric DNA biosensor was employed to monitor artificial APL PML/RARα fusion …

Active Response Of Polymer Materials From External Stimuli – Solvents And Light; Grafting Reactions On Perovskite Layers, Jianxia Zhang

LSU New Orleans Theses and Dissertations

The active response of a series of polymeric materials was investigated. Both solvent activated and light activated thin films and wire systems show dynamic behaviors when exposed to different stimuli.

Solvent mediated fluxional behavior of polymer thin films involved extensive, rapid curling both on infusion and evaporation of good solvents. These films can be either lab-fabricated ones or commercial ones, and the curling behavior can be as fast as seconds. Conditions including polymer materials, chosen solvents, and film geometry can affect the behavior.

Methods that allowed for the creation and retention of distorted wire structures were also developed; the asymmetric …

Electrochemical Preparation Of Nanostructural Pt-Ni And Pd-Ni Films For Ethanol Electro-Oxidation, Chen-Zhong Yao, Hui-Xuan Ma, Bo-Hui Wei

Journal of Electrochemistry

The Pt-Ni and Pd-Ni films were successfully prepared on Ti substrates by electrodeposition method. The porous Pt-Ni nanoflakes appeared to be uniform with the thickness of the slices about 10 ~ 20 nm. The porous Pd-Ni nanoparticles with a flower shape appeared to be uniform with the diameters of 50 ~ 60 nm. The XRD patterns also indicated that the Pd-Ni and Pt-Ni nanostructures have the poor crystallinity. The onset potentials of ethanol oxidation were negatively shifted to –0.74 V on Pt-Ni electrodes and –0.71 V on Pd-Ni electrodes, respectively. Addition of Ni could enhance catalytic activities and antitoxic properties …

Electrochemical Performances Of Carbon-Coated Na2Ti6O13 Nanotubes, Guo-Ran Li, Shuai Sun, Xue-Ping Gao

Journal of Electrochemistry

With rutile TiO₂ and NaOH as starting materials, the Na₂Ti₆O₁₃ nanotubes were prepared by a hydrothermal reaction. The carbon-coated Na₂Ti₆O₁₃ nanotubes were obtained by treating the Na₂Ti₆O₁₃ nanotubes for 4 h in glucose aqueous solutions containing 0.1 mol·L^-1 NaOH. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microcopy (TEM). The results showed that the dimensions of carbon-coated Na₂Ti₆O₁₃ nanotubes were 14 ~ 19 nm of outer diameter, 2 ~ 5 …

Ag Nanoparticles Self-Assembled Films On Iron Surface And Their Inhibition Properties, Zhe Zhang, Ming-Zi Jia, Le Ruan

Journal of Electrochemistry

The Ag nanoparticles were prepared in aqueous solutions through a chemical reduction method and transferred from water phase to toluene phase with the protection of 1-dodecanethiol (DDT). The polished iron electrode was immersed in the DDT-protected metal nanoparticles toluene solutions to form DDT/Ag nanoparticles self-assembled mixed films. Electrochemical methods such as electrochemical impedance spectroscopy and polarization curve measurement were used to study the inhibition properties of the self-assembled films in the 0.5 mol·L^-1 H₂SO₄ solution. The appearance of elements such as S and Ag from the XPS data identified the presences of DDT and Ag nanoparticles.

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …

Superhydrophilic/Superhydrophobic Surface Constructions On Titanium And Their Effects On Anti-Bacterial Properties, Guo-Wei Wang, Qiao-Ling Huang, Ren Hu, Chang-Jian Lin, Hao Wang, Li-Hai Zhang, Pei-Fu Tang

Journal of Electrochemistry

The microbial infection of biomaterials often causes clinic problems and sometimes even leads to the prosthesis failure. It is, therefore, important to prevent the biomaterials from bacterial contamination. This can be done by using anti-bacteria drugs. However, this method causes physiological burdens to the patients and does not always work. To stop the contamination from the just beginning is believed to be a better choice. The first step for infection is the attachment of bacteria on the material. In this work, the thin TiO₂ nanotubes array films were constructed with totally different wettabilities showing either superhydrophobic or superhydrophilic. The …

Electrocatalytic Determination Of 15 Kinds Of Phenolic Compounds By Novel Gold Nanoparticles-Modified Glassy Carbon Electrode, Yan-Ping Cui, Wei-Xing Wang, Chang-Zhu Yang, Wen-Hong Pu

Journal of Electrochemistry

A gold nanoparticles modified glassy carbon electrode (Au/GCE) was used to detect 15 kinds of phenolic compounds. In the cyclic voltammetry measurements, the peak currents of phenolic compounds at Au/GCE were all increased as compared with GCE and planar gold electrodes, and the oxidation potentials were determined by the activity of analytes. Besides, electrocatalysis of salicylic acid was studied at Au/GCE. The results showed that, there was a good linear relationship between the oxidation current and the concentration of salicylic acid, and the current sensitivity was 1.8 fold higher than that obtained on GCE. Trace phenolic compounds determination could be …

Electrochemical Studies On Surface Inclusion Of Β-Cyclodextrin With Adriamycin, Jian Shi, Qi-Ping Zhang, Nan-Ping Wang

Journal of Electrochemistry

The β-cyclodextrin (β-CD) modified gold electrode (β-CD/Au) was fabricated to study the electrochemical behavior of adriamycin (ADM). The results indicated that the complexing reaction of ADM with β-CD took place at the β-CD/Au surface. At 25 °C, the complexing constant (K) was 9.54×10⁴ L·mol^-1 in pH=7.0. The K values changed regularly with temperature, and the most suitable temperature of the surface inclusion reaction was 30 ℃. The complexing reaction of ADM with β-CD at the β-CD/Au surface could undergo the quasi-reversible electrochemical reaction with the rate constant being 0.0995 s^-1. The cathodic peak current (Ip) of …

Development Of Dehydrogenase-Based Bioanode Using Poly(Phenosafranin)-Functionalized Swcnt Nanocomposites And Its Application To Ethanol Biosensor, S. Saleh Farhana, Okajima Takeyoshi, Lanqun Mao, Takeo Ohsaka

Journal of Electrochemistry

A New type of dehydrogenase-based amperometric ethanol biosensor was constructed using alcohol dehydrogenase (ADH) which was immobilized on the edge-plane pyrolytic graphite (EPPG) electrode modified with poly(phenosafranin)-functionalized single-walled carbon nanotube (PPS-SWCNT). The PPS-SWCNT modified EPPG electrode was prepared by electropolymerization of phenosafranin on the EPPG electrode which was previously coated with SWCNT. The performance of the ADH/PPS-SWCNT/EPPG electrode was evaluated using cyclic voltammetry and amperometry in the presence of ethanol. The fabricated ethanol biosensor provided a reasonable sensitivity of 2.0 μA cm–2 mM–1 and a low detection limit (36 μM) for the electrocatalytic oxidation of ethanol with a linear concentration …

Surface Diffusion Of Adsorptive Species On Gold Nanoelectrodes, Bao-Fa Su, Wei Wang, Dong-Ping Zhan, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Gold nanoelectrodes were prepared successfully by a programmed laser puller. The Faraday adsorptions of oxygen and iodine, and the underpotential deposition of lead on the gold nanoelectrodes were investigated. The results showed that the active areas of nanoelectrodes were dramatically higher than their appearant geometry areas, which is caused by the surface diffusion of adsorptive species from the nanoscale gold/electrolyte interface to the adjacent gold surface.

Study On The Fluorescent Carbon Nanodots With Electrochemical Methods, Bao-Ping Qi, Yan-Min Long, Lei Bao, Cui Liu, Zhi-Ling Zhang, Dai-Wen Pang

Journal of Electrochemistry

Carbon nanodots are a new class of fluorescent nanoparticles with a carbon-based core, which possess wavelength-tunable luminescence, high photostability, resistance to photobleaching, water-solubility, and ease of bioconjugation. Owing to their attractive merits, carbon nanodots like other carbon nanomaterials such as fullerene, carbon nanotubes and graphene, have attracted much attention. In addition, carbon nanodots can be inexpensively produced by electrochemical methods with simple post-processing under mild conditions. Electrochemical approaches have unique advantages in the analysis of surface structures and luminescence mechanism of materials. In this review, recent advances in electrochemical methods used for the synthesis and luminescence mechanism of fluorescent carbon …

Study On The Electrochemical Behaviors Of Gc Electrode Modified With Carbon Nanotube-Polyelectrolytes And Its Application For Rutin Detection, Liang Hua, Xia-Qin Wu, Rong Wang

Journal of Electrochemistry

The electrochemical behaviors of rutin and ascorbic acid at single-wall carbon nanotube and polyelectrolytes (dimethyl-diallylammonium chloride, PDDA) film modified glassy carbon electrode was investigated. The cyclic voltammetric results showed that electron transfer of rutin at PDDA/SWCNTs/GC modified electrode is an adsorption-controlled process. The separation of oxidation peak potentials of rutin and ascorbic acid was more than 200 mV. The rutin concentration in the presence of AA were detected by differential pulse voltammetry (DPV). The experimental results indicated that the PDDA/SWCNTs/GC modified electrode can be used for the detection of rutin in the presence of high concentration of AA. The DPV …

The Flip-Flop Behavior Of Acetonitrile At Au Electrode Surface Investigated By Sum Frequency Generation Vibrational Spectroscopy, Zhi Huang, Xin Tang, Gang-Hua Deng, En-Cai Zhou, Hong-Fei Wang, Yuan Guo

Journal of Electrochemistry

The electrochemical interface between liquid acetonitrile and polycrystal gold electrode is investigated by in situ infrared visible sum frequency generation spectroscopy (SFG-VS). The structure of acetonitrile adsorbed at polycrystal gold electrode surface is studied as a function of electrode potential. The SFG spectra of CH₃ group indicate acetonitrile orients in response to the electrode potential. The SFG signal of CH₃ group turns lower as the electrode potential changes from -700mV to 300mV, and vanishes around the 300mV(pzc), then becomes a negative signal above 500mV, which indicates that the orientation is predominately with the CH₃ group toward the …

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Influence Of Tert-Butylpyridine On The Band Energetics Of Nanostructured Tio2 Electrodes And The Photoelectrochemical Properties Of Dye-Seneitized Electrodes, Shu-Ming Yang, Ji-Chao Wang, Hui-Zhi Kou, Hong-Bin Xue, Hong-Jun Wang, Yu-Ling Guo

Journal of Electrochemistry

The flat band edges (Efb) of nanostructured TiO₂ electrodes in electrolyte solutions with tert-butylpyridine (TBP) of different concentrations have been determined with spectroelectrochemical technique. TBP played a role in band energetics of nanostructured TiO₂ electrodes. The Efb values of -2.25, -2.46 and -2.62 V were determined in three 0.2 mol•L^-1 tetrabutylammonium perchlorate (TBAP) acetonitrile electrolytes which contain 0, 0.2 and 0.4 mol•L^-1 TBP respectively. The addition of Li+ ions shifted Efb positively. The Efb values of -1.12, -1.22 and -1.30 V were determined in three 0.2 mol•L^-1 LiClO₄ acetonitrile electrolytes which contain 0, 0.2 …

Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

CO₂ reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO₂ reduction on Cu(111) surface are CO₂(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH₂O* → (CH_2⁺O)*, CH₂* + 2H* → CH₄ or 2CH₂* → C₂H₄. On Cu(111) surface, the reaction rate is controlled by steps of CH₂O* → (CH_{2 …}

A Titanium-Supported Nanoporous Pd Electrocatalyst For Methanol Oxidation, Feng-Juan Niu, Qing-Feng Yi

Journal of Electrochemistry

Titanium-supported nanoporous palladium electrode(nanoPd /Ti) was prepared by a hydrothermal process in the presence of the ligand EDTA and using formaldehyde as reducing agent.SEM images showed that the size of Pd particles was about 60 nm and the Pd particles were connected with each other to form a three-dimensional network structure.Cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS) were applied to evaluate the electrocatalytic activity of the nanoPd/Ti electrode towards methanol oxidation in alkaline solution.CV results showed that the nanoPd /Ti electrode presented high anodic peak densities and a low onset potential for methanol oxidation.Also nanoPd /Ti electrode showed excellent CO tolerance …