Materials Chemistry Commons^™

Electrochemical H2O2 Sensor Based On The Co-Immobilization Of Phosphmolybdic Acid And Graphene On Pedot Film Electrode With Nafion, Hao-Xian Zhou, Jun-Ming Zhang, Zhi-Yu Qu, Pan-Yu Zhang, You-Jun Fan

Journal of Electrochemistry

With a glassy carbon electrode (GCE) as the substrate, the poly(3,4-ethylenedioxythiophene) (PEDOT) film electrode was prepared through the electrochemical polymerization method, then a novel non-enzymatic electrochemical H₂O₂ sensor was fabricated by co-immobilizing phosphomolybdic acid and graphene with Nafion on the PEDOT/GCE electrode. The modified electrodes were characterized by scanning electron microscopy (SEM), while the responsive properties of the sensor to H₂O₂ were investigated by cyclic voltammetry and chronoamperometry. The results demonstrated that, under the optimized conditions, the sensor exhibited good electrocatalytic performance for H₂O₂ reduction. The current response of the sensor …

Improving The Electrochemical Properties Of Polyaniline By Doping With Silver Ions, Hui Xu, Jin-Juan Pu, Yong Chen, Jian Liu

Journal of Electrochemistry

Polyaniline (PANI) is an attractive candidate among the various conductive polymers based on its unique doping/de-doping behavior, intrinsic electrical conductivity, facile synthesis, and environmental stability. However, the poor conductivity and cycle stability in an acid medium have restricted its applications. Our work aims at solving the above problems effectively by doping silver ions into PANI. The PANI and PANI doped with silver ions (PANI/Ag⁺) were synthesized by a facile interfacial polymerization process, which used aniline as a starting material in toluene in contact with an aqueous solution of silver nitrate varied from 0.04 mol•L^-1 to 0.20 mol⋅L …

Adsorption Behavior Of Rhodamine 6g On Silver Surfaces Studied By Electrochemical Surface-Enhanced Raman Spectroscopy, Chan-Juan Chen, Cheng Zong, Guo-Kun Liu, Bin Ren

Journal of Electrochemistry

Rhodamine 6G (R6G) is one of the most common probe molecules employed in single molecule surface-enhanced Raman spectroscopy (SM-SERS). The study in adsorption behavior of R6G will help understand the interactions between R6G and surface. In this paper, we used electrochemical surface-enhanced Raman spectroscopy (SERS) to study the potential-dependent adsorption behavior of R6G on silver electrodes. Our results show that when the potential moved negatively, the orientation of R6G on silver surface changed from vertical to inclined adsorption. This result indicates that the abnormal SM-SERS spectra of R6G observed in the former SM-SERS studies from other research groups are due …

Electrochemical Detection Of Hydrogen Peroxide At Aunps Modified Electrode Using P-Hydroxyphenylboronic Acid As A Precursor, Chun-Yan Wang, Xiao-Qiu Liu, Ying-Xin Qi

Journal of Electrochemistry

We developed a new method for electrochemical detection of hydrogen peroxide (H₂O₂) based on boronate oxidation of p-hydroxyphenylboronic acid. This method using p-aminophenol which is produced from the reaction of H₂O₂ and p-aminophenylboronic acid as a well electrochemical probe, combined with a gold nanoparticles (AuNPs) modified electrode for an indirect detection of H₂O₂. Because of the large surface area and enhanced electrocatalytic behavior by the AuNPs modified electrode, the detection sensitivity was improved. The method could detect H₂O₂ in the concentration range of 1 ~ 100 …

Electrochemical Determination Of Hg(Ii) At Gold Nanoparticles@Carbonaceous Microspheres Modified Electrode, Tian-Yu Qiu, Ming-Chun Wang, Xian-Feng Du, Tian-Jia Jiang, Xing-Jiu Huang

Journal of Electrochemistry

The gold nanoparticles@carbonaceous microspheres (Au@CMSs) and  Au@CMSs modified glassy carbon electrode (GCE) were prepared. The Au@CMSs modified  GCE was further examined for possible sensitive detection of mercury ions (Hg(II)) in an aqueous solution by square wave anodic stripping voltammetry (SWASV). The excellent performance was found in the stripping analysis of Hg(II) in 0.1 mol•L^-1 NaAc-HAc(pH=5.0) with a sensitivity of 25.863 A•(mol•L^-1)^-1 and a detection limit of 3.69×10^-8 mol•L^-1 based on the 3σ method.

Fabrication Of Riboflavin Electrochemical Sensor Based On Au Nanoparticles/Polydopamine/Carbon Nanotubes Modified Glassy Carbon Electrode, Hua-Ping Peng, Mei-Ling Yu, Xin Liu, Pan Liu, Wei Chen, Ai-Lin Liu, Xin-Hua Lin

Journal of Electrochemistry

A novel electrochemical platform for the high sensitivity detection of riboflavin was constructed by Au nanoparticles/polydopamine/carbon nanotubes (Au-PDA-MWCNTs) nanocomposite modified glassy carbon electrode. The Au-PDA-MWCNTs nanocomposite was synthesized by in situ reduction method. The characteristics of the as-prepared Au-PDA-MWCNTs nanocomposite modified electrodes were investigated by using UV-Vis spectroscopy, scanning electron microscopy (SEM) and electrochemical methods. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to study the electrochemical behavior of riboflavin (RF) at Au-PDA-MWCNTs nanocomposite modified electrodes. The results demonstrated that the present electrochemical sensor exhibited a wide linear range from 5×10^-9 mol•L^-1to 1×10^-5 mol•L …

Synthesis Of Fe, N-Doped Graphene/Carbon Black Composite With High Catalytic Activity For Oxygen Reduction Reaction, Chi Chen, Zhi-You Zhou, Xin-Sheng Zhang, Shi-Gang Sun

Journal of Electrochemistry

Oxygen reduction reaction (ORR) is a bottleneck for improving the efficiency of proton-exchange membrane fuel cells as a cathode reaction due to its sluggish kinetics. The exploitation of low cost and high performance non-precious metal catalysts such as Fe/N/C based materials toward ORR has attracted extensive attentions. In this work, the Fe, N-doped graphene nanosheets/carbon black composite was prepared by hydrothermal polymerization and followed by a twice-heat-treatment procedure using 2-aminoimidazole as an N precursor, FeCl₃ as an Fe precursor and KJ600 carbon black as a support. The TEM images revealed that the graphene nanosheets were separated by carbon black …

Electrochemical Syntheses Of Graphene And Its Composites, Bo Zhao, Li Jiang, Ming-Hui Yuen, Xian-Zhu Fu, Rong Sun, Ching-Ping Wong

Journal of Electrochemistry

Graphene is a kind of ideal two-dimensional flat carbon nanomaterials which have unique chemical and physical properties. The attractive potential applications must be based on the high quality mass production of graphene. However, it remains a huge challenge. An electrochemical approach is a fast, environmental friendly and easy-operating method. single- or multi-layered graphene flakes can easily be produced in short periods of time. In this review, the structure, properties and preparation methods of graphene are first introduced. Accordingly, the electrochemical approaches used for the productions of graphene flakes, graphene/inorganic nanocomposites, graphene/polymer composites and graphene analogues are highlighted. Finally, challenges and …

Effect Of Flame Retardant On Electrochemical Performances Of Lithium Ion Battery With Lini0.4Co0.2Mn0.4O2 As A Positive Electrode Material, Yan-Zhuo Lv, Yong-Xian Ge, Zhen-Bo Wang, Ke Ke

Journal of Electrochemistry

The effect of flame retardant on the electrochemical performances of lithium ion battery by using LiNi_0.4Co_0.2Mn_0.4O₂ as a positive material was studied by measuring the first charge-discharge, cycling, circulation, and AC impedance curves. The experimental data indicated that the discharge capacity of the battery decreased, while the charge transfer resistance and the lithium ion diffusion resistance increased with the increases in the concentrations of the flame retardant in the electrolyte solutions. Furthermore, the stability of the battery at small discharge ratios and the cyclic performance were also improved by the addition of flame …

Electricity Generation Of Microbial Fuel Cell Using Stainless Steel Mesh As Cathode, Hong-Yan Dai, Hui-Min Yang, Xian Liu, Xuan Jian, Xiu-Li Song, Zhen-Hai Liang

Journal of Electrochemistry

In the present work, a dual-chamber microbial fuel cell (MFC) was constructed with aeration tank sludge as an inoculum, carbon felt as an anode and stainless steel mesh without any modification as a cathode. The influence of the cathode size was investigated in terms of voltage output, power generation and electrochemical impedance. The long-term durability of the stainless steel mesh cathode was also evaluated. Results showed that the stainless steel mesh exhibited satisfactory long-term durability as MFC cathode. When the stainless steel mesh size was 2 × 2 cm², the maximum output voltage, power density, the internal resistance …

The Study On Comparison Of Electrochemical Performance In Microbial Fuel Cell With Glucose And Sodium Acetate Acting As Substrates, Lei Fan, Yu Zhao, Ting Li, Qin-Bo Yuan, En-Zhi Wang, Xiao-Bin Wang, Jun-Wen Wang

Journal of Electrochemistry

By inoculating aerobic sludge and anaerobic sludge from the sewage treatment plant, two sets of dual-chamber microbial fuel cells (MFCs) were built with either glucose or sodium acetate acting as a substrate. Accordingly, the electrochemical performances of MFCs were explored with the concentration of the substrates being 0.0335 mol⋅L^-1. The results of the comparative study in glucose system and sodium acetate system showed that the impedance values of anodic half cell were 222 Ω for glucose and 213.67 Ω for sodium acetate, implying no significant effect on the internal resistance in battery with the different substrates. The exchange …

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

The Dawn Of New Quantum Dots: Synthesis And Characterization Of Ge1-Xsnx Nanocrystals For Tunable Bandgaps., Richard J. Esteves

Theses and Dissertations

Ge_1-xSn_x alloys are among a small class of benign semiconductors with composition tunable bandgaps in the near-infrared spectrum. As the amount of Sn is increased the band energy decreases and a transition from indirect to direct band structure occurs. Hence, they are prime candidates for fabrication of Si-compatible electronic and photonic devices, field effect transistors, and novel charge storage device applications. Success has been achieved with the growth of Ge_1-xSn_x thin film alloys with Sn compositions up to 34%. However, the synthesis of nanocrystalline alloys has proven difficult due to larger discrepancies (~14%) in …

Enabling Method To Design Versatile Biomaterial Systems From Colloidal Building Blocks, Shalini Saxena, L. Andrew Lyon

Biology, Chemistry, and Environmental Sciences Faculty Articles and Research

Development of materials with fine spatial control over topographical, mechanical, or chemical features has been investigated for a variety of applications. Here we present a method to fabricate an array of polyelectrolyte constructs including two-dimensionally and three-dimensionally patterned assemblies using both compressible and incompressible colloidal building blocks. This method eliminates prior constraints associated with specific chemistries, and can be used to develop modular, multi-component, patterned assemblies. In particular, development of constructs were investigated using microgels, which are colloidally stable hydrogel microparticles, polystyrene (PS) beads, and PS-microgel core-shell building blocks in conjunction with the polycation poly(ethyleneimine) (PEI). The topography, mechanical properties, …

Characterization Of Biochars Produced From Peanut Hulls And Pine Wood With Different Pyrolysis Conditions, James W. Lee, Bob Hawkins, Michelle K. Kidder, Barbara R. Evans, A. C. Buchanan, Danny Day

Chemistry & Biochemistry Faculty Publications

Background

Application of modern biomass pyrolysis methods for production of biofuels and biochar is potentially a significant approach to enable global carbon capture and sequestration. To realize this potential, it is essential to develop methods that produce biochar with the characteristics needed for effective soil amendment.

Methods

Biochar materials were produced from peanut hulls and pine wood with different pyrolysis conditions, then characterized by cation exchange (CEC) capacity assays, nitrogen adsorption–desorption isotherm measurements, micro/nanostructural imaging, infrared spectra and elemental analyses.

Results

Under a standard assay condition of pH 8.5, the CEC values of the peanut hull-derived biochar materials, ranging from …

Fabricating Superhydrophobic And Superoleophobic Surfaces With Multiscale Roughness Using Airbrush And Electrospray, Karam N. Almilaji

Theses and Dissertations

Examples of superhydrophobic surfaces found in nature such as self-cleaning property of lotus leaf and walking on water ability of water strider have led to an extensive investigation in this area over the past few decades. When a water droplet rests on a textured surface, it may either form a liquid-solid-vapor composite interface by which the liquid droplet partially sits on air pockets or it may wet the surface in which the water replaces the trapped air depending on the surface roughness and the surface chemistry. Super water repellent surfaces have numerous applications in our daily life such as drag …

Understanding Electrical Conduction In Lithium Ion Batteries Through Multi-Scale Modeling, Jie Pan

Theses and Dissertations--Chemical and Materials Engineering

Silicon (Si) has been considered as a promising negative electrode material for lithium ion batteries (LIBs) because of its high theoretical capacity, low discharge voltage, and low cost. However, the utilization of Si electrode has been hampered by problems such as slow ionic transport, large stress/strain generation, and unstable solid electrolyte interphase (SEI). These problems severely influence the performance and cycle life of Si electrodes. In general, ionic conduction determines the rate performance of the electrode, while electron leakage through the SEI causes electrolyte decomposition and, thus, causes capacity loss. The goal of this thesis research is to design Si …

Dynamic Atomistic Study Of Tunnel Functions In Nanostructured Transitional Metal Oxides, Yifei Yuan

Dissertations, Master's Theses and Master's Reports

Alpha (α-) MnO₂ is a well know transitional metal oxide possessing one dimensional 2×2 (4.6 × 4.6 Ų) tunnels for accommodation of various ions. Such a characteristic tunneled structure has enabled the wide applications of α-MnO₂ in the fields of ion exchange, molecular sieves, biosensor, catalysis and energy storage. This PhD dissertation focuses on the dynamic study of ion transport functionality of α-MnO₂ at atomic level using an aberration corrected scanning transmission electron microscopy equipped with a special holder with a scanning tunneling microscopy probe.

The wide application of in situ TEM studying the dynamic …

Applications Of Carbon Materials In Electrochemical Energy Storage, Ji Liang, Lei Wen, Hui-Ming Cheng, Feng Li

Journal of Electrochemistry

An electrode material for electrochemical energy storage is one of the key components for high performance devices. In a variety of electrochemical energy storage systems, carbon materials, especially the lately emerged carbon nanomaterials including the carbon nanotube and graphene, have been playing a very important role and brought new vitality to the development and demonstration of the broad application prospects. In this review, we summarize the applications of various carbon materials in the typical electrochemical energy storage devices, namely lithium/sodium ion batteries, supercapacitors, and lithium-sulfur batteries, as well as flexible electrochemical energy storage and electrochemical catalysis. A perspective of novel …

Electrodeposition Of Lanthanum In Deep Eutectic Solvents, Li Wang, You-Jun Fan, Lu Wei, Hai-Xia Liu, Shi-Gang Sun

Journal of Electrochemistry

With the choline chloride/urea deep eutectic solvents (DESs) as the medium, the olive-like lanthanum particles with uniform shape and size were successfully prepared through a potentiostatic deposition method. The prepared samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray (EDX) spectroscopy and X-ray photoelectron spectroscopy (XPS). At the same time, the effect of deposition potential, temperature and time on the size and morphology of samples was investigated. The results demonstrated that the optimum conditions for the preparation of olive-like lanthanum particles were as follows: deposition potential of -1.7 V, temperature of 80 °C and …

Progress Of Self-Supported Supercapacitor Electrode Materials Based On Carbon Substrates, Shui-Jian He, Wei Chen

Journal of Electrochemistry

Self-supported electrode materials have been widely used in supercapacitors. Carbon materials are promising substrates in building self-supported electrode materials attributed to their diverse structures, rich resource, relatively low cost and high stability. Combined with our own research in this field, we summarize here the recent progress on the synthesis of self-supported electrode materials and their supercapacitance properties. The overall synthetic strategy could be divided into two categories: “top-down” and “bottom-up”. We hope this review is helpful for the development and application of renewable sources in self-supported electrode materials.

Synthesis Of Porous Carbon Nanosheets And Its Application In Sodium-Ion Battery, Jing-Fei Zhang, Jing Lu, Xiao-Yu Yang, Yun-Di Huang, Lin Xu, Dong-Mei Sun, Ya-Wen Tang

Journal of Electrochemistry

Owning to sodium’s high abundance, relatively low cost, similar chemical properties to Li and very suitable redox potential of E₀(Na⁺/Na) = -2.71 V versus SHE which is only 0.3 V above that of lithium, rechargeable sodium ion battery hold much promise as potential alternatives to current lithium ion batteries for energy storage applications. Carbon material is regarded as the most promising anode candidate for sodium ion battery. Particularly, carbon nanosheet with porous structure and high conductivity is expected to have improved sodium ion storage properties. In this paper, we present a two-step pyrolysis-based method for facile …

Intercalation Of Clo4- Into Hopg Investigated By Ec-Stm, Xiao-Yan Hu, Alice Aliwowe, Jia-Wei Yan, Bing-Wei Mao

Journal of Electrochemistry

The electrochemical intercalation and surface morphology of highly oriented pyrolytic graphite (HOPG) electrode in 2 mol⋅L^-1 HClO₄ were studied by in situ scanning tunneling microscopy (STM) and cyclic voltammetry (CV). Based on the step-height changes observed before and after the intercalation, the effects of different step sites on intercalation are compared. The feasibility, reversibility and speed of intercalation are discussed. The intercalation ofClO₄^- into HOPG can be divided into three types depending on the number of graphite layers at the step site: When the layers of graphite are more than three, the intercalation becomes feasible; when …

Effect Of Mno2 Content On Electrochemical Capacitance Behavior Of Active Carbon Electrode, Kun Shen, Xian-Liang Zhou, Qi-Shun Duan

Journal of Electrochemistry

In this work, the manganese dioxide (MnO₂) materials were prepared by solution approach at low temperature, thermal decomposition and electrochemical deposition. The actived carbon (AC) and MnO₂composite electrodes were used for aqueous supercapacitors. The morphologies and structures of the prepared materials were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the electrochemical behaviors were tested by cyclic voltammetry (CV) and galanostatic charge-discharge tests. Electrochemical test data show that the maximum specific capacitances of 151, 172 and 141 F•g^-1were obtained with the contents of MnO₂being 70, 60 and 70% in …

Fast And Accurate Evaluation Of Lifepo4 Cathode Materials By Single Particle Microelectrode, Fu-Qing Wang, Yi-Min Wei, Yu-Zhuan Su, Bing-Wei Mao, Kai Wu, Feng-Gang Zhao, Chun-Lei Chen, Xing-Lu Li, Jin Chong

Journal of Electrochemistry

Single particle microelectrode enables to evaluate the electrochemical responses for single particle of active material without binder and conductive agent. Thus, the influences of additive and electrode structure on the electrochemical performance of active materials can be ignored. Furthermore, this technology can be used to evaluate active materials fast. Therefore, single particle microelectrode allows fast and accurate determination of the intrinsic performance of active material. Cyclic voltammogram (CV), cycle performance, and kinetic behavior of LiFePO₄ cathode materials were evaluated by the single particle microelectrode. CV curve of LiFePO₄ particle with a pair of oxidation and reduction peaks was …

Special Issue: Electrochemistry Of Carbon Materials, Wei Chen

Journal of Electrochemistry

Carbon materials are traditional electrode materials due to their excellent electrical conductivities, high electrochemical stabilities and wide potential windows. Glassy carbon, graphite, various activated charcoals, carbon fibers etc. have been widely used in electrochemistry serving as electrode substrates or supports. In addition to their applications in basic electrochemistry, carbon materials have also played important roles in electrochemical energy storage and conversion. In recent years, various types of carbon structures, from zero-dimensional carbon nanodots, one-dimensional nanotubes, two-dimensional graphene to three-dimensional porous carbons, have attracted increasing attention in electrochemical field. It has been found that carbon materials have outstanding properties as advanced …

Colloidal Ionic Supercapacitors, Kun-Feng Chen, Dong-Feng Xue

Journal of Electrochemistry

Supercapacitors have high power density and long cycle life compared with battery systems, but they still suffer from low energy density at the same time. In order to increase the energy density of supercapacitors, we have developed a new type of pseudocapacitor, called colloidal ion supercapacitor, which can directly use commercial metal salts as electrode materials and form electroactive matter by in-situ electrochemical reactions without the need of additional materials synthesis processes. Colloidal ion supercapacitor can fully utilize the redox reaction of metal cations with multiple oxidation states, which can completely release the stored electrical energy of multiple-valence cations, leading …

Carbon Aerogel/Nickel Foam As Electrode For High-Performance Supercapacitor, Zhong Wu, Xin-Bo Zhang

Journal of Electrochemistry

Herein, a facile synthesis has been explored to prepare carbon aerogel/Ni foam. Graphene oxide, resorcinol and formaldehyde serve as precursors and polymerize in-situ on the Ni foam after hydrothermal synthesis at 85 ℃. After lyophilization treatment, the carbon aerogel/Ni foam with porous structure can be obtained. Electrochemical investigations reveal that the carbon aerogel/Ni foam exhibits superior performances in both aqueous and organic electrolytes involving high specific capacitance and long-term cycling stability. The excellent properties can be ascribed to the unique formation and porous structure, which allows more effective transportations of electron and electrolyte ion.

Applying Bayesian Machine Learning Methods To Theoretical Surface Science, Shane Carr

McKelvey School of Engineering Graduate Student Theses & Dissertations

Machine learning is a rapidly evolving field in computer science with increasingly many applications to other domains. In this thesis, I present a Bayesian machine learning approach to solving a problem in theoretical surface science: calculating the preferred active site on a catalyst surface for a given adsorbate molecule. I formulate the problem as a low-dimensional objective function. I show how the objective function can be approximated into a certain confidence interval using just one iteration of the self-consistent field (SCF) loop in density functional theory (DFT). I then use Bayesian optimization to perform a global search for the solution. …

Short Review On Electrochemical Energy Storage, Hong Li, Ying-Chun Lyu

Journal of Electrochemistry

Energy storage is a critical supporting technology in many fields such as energy, information, transportation, and healthcare, aerospace, advanced manufacture, advanced equipment, national security. Electrochemical energy storage technique has been widely applied and is developing continuously. In this article, the energy storage mechanism, technical indicators and technology ready level in electrochemical energy storage are summarized. Mainly based on lithium ion batteries, untraditional electrochemical issues in electrochemical energy storage devices are described from the perspective of fundamental science. These issues deal mainly with thermodynamics, kinetics, size effect, asymmetric system, asymmetric reaction path, surface phenomenon, hybrid ion transportation, and solid state battery. …