Materials Chemistry Commons^™

Electrodeposition Of Cu-Co Multilayer Thin Films, Jiangyun Xue, Jixun Wu, Dejun Yang

Journal of Electrochemistry

A method has been developed to produce Cu-Co Multilayer from a single electrolyte by electrodeposition. The effects of the concentration of copper ions, current density and the speed of rotation were investigated, and the Cu-Co electrodeposition films were analysed by TEM, AES and X-ray diffraction. The results indicated that the film was alternating pure copper and coppercobalt alloy layers. If the content of copper in cobalt layer is to be small, the concentration of its ions in solution must be small and the rotation speed must be low.

Study On The Ionic Conductivity Of Comb Polymer Electrolytes, Liming Ding

Journal of Electrochemistry

A comb polymer (CP350) with oligo-oxyethylene side chains was prepared from methyl vinyl ether/maleic anhydride copolymer.The ionic conductivity of CP350/LiAsF₆ and CP350/LiAsF₆ complexes was studied as a function of temperature and [Li]/[EO] ratios. A equivalent circuit was given to interpret complex impedance spectra. At 25 ℃, the ionic conductivity maxima of the two systems are 1.38×10^-4, 8.32×10^-5 S/cm respectively. The appearance of the conductivity maxima has been interpreted as being due to the effect of microviscosity on ion transport. lonic conduction displays non-Arrhenius behaviour. The temperature dependence of ionic conductivity was attributed mainly to the …

Electrochemical Studies On Chemical Polishing Of Copper, Keping Han, Jingli Fang

Journal of Electrochemistry

Changes in specular reflectivity,weight loss,surface topograph and potential with time and current-potential curves during chemical polishing were determined. The results showed that chemical polishing was composed of the etching, polishing and pitting stage. The passivating film theory also applied to the chemical polishing.

Study On The Growth Process Of Lead Dioxide On Lead-Antimony Electrodes By Impedance Tracing Method, Guolin Wei, Hongxin Yang, Jiarong Wang

Journal of Electrochemistry

The growth process of PbO₂ formed by the oxidation of PbSO₄ in the anodic film on lead-(1,3,5,7)wt% antimony electrodes was investigated with impedance tracing method of single frequency and the current-time transient method. The influence of antimony on this process was studied.The simulation curves obtained for capacity-time transients fit the experimental results very well. It has been shown that the mentioned growth process is a two-dimentional instantaneous nucleation and growth process. Antimony will inhibit the growth of PbO₂ nucleus but enhance its nucleation.

The Relationship Between Ionic Conductivity And The Structure Of The New Polymer Electrolytes, Hongze Liang, Yongxiang Song, Liming Ding, Yuchen Qi, Lixia Li, Xiabin Jing, Fusong Wang

Journal of Electrochemistry

Ionic conductivity of polymer-eutectic composed of lithium perchlorate and lithium nitrate has been studied. The effects of eutectic and polymers upon the conductivities have been discussed.The lonic conductivity depends on the eutectic properties as well as the treatment method of samples.

Corosion Potential Imagingat The Interface Of Coating/Metal By A New Electrochemical Technique, Changjian Lin, Xiangdong Zhuo, Jidong Chen, Hui Wang, Rong-Zong Hu, Yi Song, Jian-Guang Tan

Journal of Electrochemistry

/

Problems On The Study Of Anodic Films On Pb In Sulfuric Acid Solution (Ⅱ), Houtian Liu, Qunzhou Wang, Yongqin Wan, Weifang Zhou

Journal of Electrochemistry

The conditions for the growth of the different phases in the anodic Pb(Ⅱ) film on Pb in sulfuric acid solution were discussed.

Status Of The Research And Development For Fuel Cell Technology Abroad, Naichao Li, Baolian Yi

Journal of Electrochemistry

Status of the research and development for fuel cell technology abroad was overviewed, and at the aim of accelerating the research and development for fuel cell technology in China, the corresponding stategy for our country was recommended.

In Situ Studies Of Copper Electrodepostion On Hopg By Using Ecstm, Zhaoxiong Xie, Bingwei Mao, Xiangdong Zhuo, Jiqian Mu, Zhaowu Tian

Journal of Electrochemistry

In this paper, copper electrodepostion on HOPG had been in situ studied by using a homebuilt electrochemical scanning tunneling microscopy (ECSTM). Three dimensional nucleation and subsequent growth of copper crystals were found as the initial stage of copper deposition on HOPG. In the case of lower overpotential or lower concentration of Cu²⁺ , the bulk deposited copper layer tended to form smooth terraces, and grow at the edge of steps. The terraces were stable to some extent, which made it possible to be observed with atomic resolution. At a higher overpotential, the crystal size of copper were somehow smaller. …

A Study Of The Electroplated Fe-Cr-Ni Alloy Microstructure, Donglin Li, Jianping Liu, Fangzhou Guo, Jianrong Hua

Journal of Electrochemistry

The microstructure of the electroplated Fe-Cr-Ni alloys from the mixed carboxylic acid solution containing Cr(Ⅲ) and additives were determined with XRD and SEM. Experimental results showed that, under the experimental condition, the phase component, structure of Cu base electroplated Fe-Cr-Ni alloys had a critical thickness, which was 11 μm and a critical Ni content, which was 32%. Organic additives, formic acid or polyethylene Glycol, mainly affected the surface, cross section morphology of the electroplated Fe-Cr-Ni alloys. Adding Mo to the electroplated Fe-Cr-Ni alloys led to remarkable corrosion resistance in concentrated HCl.

The Applications Of Poap Ni2+ Films Modified Electrode As Sensor For Alcohol, Bingzeng Hua, Wenyun Hu, Yanzhen Chen

Journal of Electrochemistry

POAP Ni²⁺ films modified electrode can electrocatalyzes significantly the oxidation of alcohol. The modified electrode can be used as the electrochemical sensor for the detection of alcohol. But the oxidation of alcohol is effected by the thickness of films、the concentration of nickel ion in films, pH of electrolyte, as well as temperative. All of those conditions have been studied in order to achieve stable response current during the oxidation of alcohol, and the relation between concentration and current has been made. At last the major characteristic parameters, such as the low limitation of concentration, the response time, the ability …

Surface Raman Spectra Of Pyridine And 2 Mercaptopyrimidine Adsorbed On Rough Nickel Electrode, Qunjian Huang, Jinsong Gao, Xiongwei Cai, Bingwei Mao, Mingsen Zheng, Zhongqun Tian

Journal of Electrochemistry

The Raman spectra of pyridine and 2-mercaptopyrimidine (2-MP) adsorbed on bare nickel electrodes roughened by a HNO₃ etching procedure have been obtained for the first time by utilizing a highly sensitive confocal Raman microscope. Their adsorption behaviours are discussed briefly. This primary result illustrates a great potential for in-situ Raman spectroscopy in the study of chemical and electrochemical processes of transition metal surfaces.

Electrocatalytic Oxidation Of Some C2 Compounds (Alcohols, Aldehydes, And Carboxylic Acids) On A Pt/SbAd Electrod, Hong Li, Lincai Jiang, Xiong Jiang

Journal of Electrochemistry

The electrocatalytic oxidation behavior of some C₂ compounds(alcohols, aldehydes and carboxylic acids) on a Pt/Sb_ad electrode prepared in-situ or ex-situ UPD was investigated using pontential sweep and rotating disc electrode methods. It is confirmed that Pt/Sb_ad electrode show the most electrocatalytical active to the oxidation of aldehyde functional group and only a little activity to the oxidation of hydroxyl group, but no activity for the oxidation of carboxyl group.

The experimental results show that the activity of the Pt/Sb_ad electrode prepared by ex-situ UPD is higher than that prepared by in-situ UPD.

The limitations of the …

Oxygen Charge Transfer Reaction At The Pt/Ysz Interface, Yi Jiang, Wenzhao Li, Jingwang Yan, Shizhong Wang

Journal of Electrochemistry

Oxygen Charge transfer reaction has been investigated by various degrees of potential polarization at the Pt/YSZ interface. Anodic and cathodic charge transfer coefficients were found to be unity over the wide range of oxygen partial pressures and temperatures. While the exchange current density of the interface was found dependent on the partial pressure of oxygen in accordance with the relation: i₀=2FKr(K_O2P_O2)^1/4(1+K_O2P_O2)^1/2. Several important parameters, such as electrochemical rate constant, equilibrium constant of oxygen adsorption on Pt surface had also been extracted.

Studies Of Surface Treatment Methods And Their Operating Mechanisms For Activation Of Hydrogen Storage Electrode, Ronghui Hu, Hanxi Yang, Shigang Lu, Shengxian Li, Jingcheng Liu, Chongzhi Yang

Journal of Electrochemistry

Surface treatment methods by use of charge discharge cycling, KBH₄ reduction and KOH etching were parallely investigated for the rapid activation of Mn(NiCoMnAl)₅ electrode. It is found that the MH electrode treated with hot and concentrated KOH solution exhibits rapid and full activation, and also gives lower discharge overvoltage, higher stable capacity and improved cycleability. It is also revealed from SEM, EDAX and ICP analysis that the KOH activation of the electrode proceeds mainly through the enrichment of mischmetal and nickel in surface to form electrocatalytically active surface for hydrogen absorption reaction, but the surface modification with KBH …

Electrocatalytic Reduction Of Nitrite In The Presence Of Complex Of Cobalt(Ⅱ) And 1,10 Phenanthroline, Jian Tong, Xiaojun Dang, Hulin Li

Journal of Electrochemistry

The electrochemistry of cobalt(Ⅱ)-1,10-phenanthroline Co(Phen)₂²⁺ complex and its ability to electrocatalyze the reduction of nitrite were studied, we found that this complex could act as a catalyst in alkaline or neutral solution for nitrite reduction. We have investigated the effect of the complex composition on electrocatalytic ability. The effects of pH value, complex concentration, regeneration and activation of electrocatalyst on the catalytic current have been studied and discussed.

Study On Electrode Constructure And Electrical Performance Of Na/S Cell, Jianhua Yang, Jiadi Cao

Journal of Electrochemistry

A sodium wick for sodium electrode and trough shaped performs for sulfur electrode in Na/S cell were designed and investigated. The experiments suggested that the sodium wick for sodium electrode not only improved the discharge performance of cell but also reduced the quantity of sodium utilization, and increased the specific energy of Na/S cell. The trough shaped preform with alumina fibres for sulfur electrode decreased the polarization, improved the charge acceptance and prolonged the life of cell.

The Reduction Of Oxygen To Hydrogen Peroxide In An Acidic Trickle Bed Cell Using Graphite Chip Cathode, Zhaoe Lu, Guanyong Zhang, Tiangeng Zhong, Guonu Fang

Journal of Electrochemistry

The authors investigated the electrochemical reduction of oxygen to hydrogen peroxide in 0.05 mol/L H₂SO₄ solution by the trickle bed electrode using graphite chip. The bed dimension was 14×5×0.6 cm. The current efficiency and the concentration of H₂O₂ in the catholyte were determined at various current strengths and various rates of adding the electrolyte. The proper current was 0.15 A. i.e. the current density was 2.1 mA/cm² vertical cross section area of the bed. The concentration of H₂O₂ reached 7×10^-3 mol/L with the current efficiency of 0.2. If the …

Electrochemical Ploymerization Of Aniline In The Alkaline Solution And Properties Of Polymer, Shaolin Mu, Jinqing Kan, Aiguang Zhang

Journal of Electrochemistry

A deep yellow polyaniline was formed at the anodic electrode during electrochemical oxidation of aniline in the alkaline solution. The peak of oxidation potential for aniline in the alkaline solution was 0.7 V (vs.Ag/AgCl with a saturated KCl solution), which is about 0.3V less than that in the acidic solution. The results from rotating ring-disk electrode experiment show that two soluble intermediates were generated during electrochemical oxidation of aniline. The colour of the polymer in the alkaline solution is independent of applied potential and pH values. An adsorption peak was observed in the UV region at 500 nm for the …

Determination Of Transport Number Of The Modified Liclo4-(Peo)20 Polymer Electrolyte, Ruqi Zhou, Qngguo Liu, Weihua Qiu, Yun Zhang, Yuee Zhao, Leiling Yang

Journal of Electrochemistry

In this work a combination method of A.C. Impedance and chronoamperometry was used to determine the lithium ion transport number of LiClO₄·(PEO)₂₀·(PC)₁₂·(EC)₁₂ polymer electrolyte. It is known that lithium is thermodynamically unstable in non-aqueous or polymer electrolytes, leading to the formtion of a film on lithium surface, called as solid electrolyte interphase (SEI). The presence of SEI layer will greatly influence the experimental result of lithium ion transport number. The new method avoid the effect of SEI layer, and can give correct transport number of lithium ion in the electrolyte of DCIO_{4 …}

Study Of Electrochemical Behaviour Of Myoglobin Using Cyclic Voltammetry And Synchronous Fluorescence Spectroscopy, Ju Chou, Haihong Zhou, Tianhong Lu, Yue Wu

Journal of Electrochemistry

/

The Inhibition Of Amphipathic S- And N-Containing Compounds On Carbon Steel Corrosion, Wei Xing, Yibin Shan, Du Guo, Tianhog Lu, Shiquan Xi

Journal of Electrochemistry

Ordered monolayers of S- and N-containing amphipathic corrosion inhibitors were depoitod onto the surfaces of carbon steel electrode with super-molecular assembly technique. The effect of molecular aggregation of monolayers on carbon steel corrosion in 0.05 mol·cm^-3 H₂SO₄ and the mechanisms of these inhibitors were discussed in details. It was found that the transport of hydrated hydrogen ion to the surface of steel depends strongly on the inhibitor molecular aggregation in the monolayers.

Development Of The High Capacity Sintered Type Nickel Positive Electrode, Guohua Yu, Shijie Zhang, Xiaolin Wang, Jingqi Wei

Journal of Electrochemistry

By improving the design and technologies of the sintered type nickel oxide positive electrode for the NiMH batteries, We do our best to increase the sinter volume and porosity,the amount of the active materals and their utilization, so we have fabricated the high capacity sintered typo nickel electrodes fitting for the NiMH battreies. The sfecitic capacity of the lot produced electrodes is up to 550 mA/cm^-3.

The Influence Of Cathode Ingredients In Zinc Chloride Type Battery On The Discharge Ability, Qi Shen, Biao Zhuang

Journal of Electrochemistry

The influence of cathodic powder ingredients in ZnCl₂ type heavy duty battery on the discharge ability has been studied, a suitable battery ingredients is founds.

Hydrogen Evolution Reaction On Nanocrystalline Co-Mo/Ni Composite-Coated Electrodes, Weizeng Yu, Jie Ma, Yiming Chu, Huizhe Zhu, Hongjie Wang, Shuncheng Liu

Journal of Electrochemistry

The electrochemical behaviours of the hydrogen evolution reaction (HER) at electrodes prepared by composite coating of nanocrytstalline Co-Mo alloy particles formed by ball milling on nickel base has been sludied by using sleady-state polarization and ac impedance techiu ques. The microstructure and the size of the nanocrystals of Co-Mo alloy and the morphology of the composite-coating surface of the electrodes are measured by XRD, TEM and SEM. Results show that the nanocrystalline Co-Mo alloys prepared by high energy ball milling has high electrocatalytic activity for HER. The electrocatalytic activity for the HER is enhanced and the energy of activation for …

Electrochemical Studies On Corroding Metallic Electrodes In Frequency Domain, Chunan Cao

Journal of Electrochemistry

The electrochemical studies on corroding metallic electrodes carried out in the State Key Laberatory for Corrosion and Protection are reviewed briefly: (1) General equations of faradaic admittance under potential-control condition were derived based on the stabillity conditions of steady processes. The faradaic admittance at mixed potential then was deduced based on these equations and the electrochemical impedance spectroscopy (EIS) at corrosion potentials in the solutions containing interface inhibitors was diseussed by application of the thecetical results obtained. (2) The spectral power density (SPD) curves for electrochemical noise (EN) during the initial stagu of pitting corrosion were observed for iron and …

Kinetic Behavior Of The Pt/Ysz Solid Electrolyte Interface Exposed To O2+He Mixture, Yi Jiang, Wenzhao Li, Lixin Cao, Jingwang Yan

Journal of Electrochemistry

Electrochemical behavior of the Pt/YSZ solid electrolyre interface has been investigated by cyclic voltammetry and linear potential sweep technique. It was found that the electrochemical adsorption of oxygen on the Pt surface follows the Temkin adsorption model. The amount of oxygen species increases logarithmically with time. Two oxygen species are electrochemically formed on the Pt surface. One is atomically adsorbed, the other probably subsurface oxygen or Pt oxide. The electrochemical reduction of adsorbed oxygen is kinetically irreverable. The cathodic peak potential is affected both by the potential sean rate and the amount of oxygen ahorbed on the surface. Kinetic parameters, …

An Indirect Electrochemical Oxidation Of Toluene─Catalytic Effects Of Ag(Ⅰ) On Mn(Ⅱ)/Mn(Ⅲ) Couple Transition At Pt Electrode, Zhonghua Wang, Yunan Qu, Xingguo Yan, Qngmin Hua, Guacai Chen, Zhongquan Wang

Journal of Electrochemistry

The Catalytic effects of Ag(Ⅰ) on toluene oxidation by Mn(Ⅲ) as well as the anodic generation of Mn(Ⅲ) were investigated. The rates of toluene oxidation were first order with respect to both Ag(Ⅰ) and Mn(Ⅲ). Ag(Ⅱ) formed on the surface of the platinum anode when Ag(Ⅰ) was present in the anolyte, which catalyic the Mn(Ⅱ) to Mn(Ⅲ) in solution.

Ftis Observation Of Twin Adsorbates Of Co On Rh Electrode In Acid Solution, Wenfeng Lin, Shigang Sun

Journal of Electrochemistry

Because of its great importance both in electrocatalysis and C1 chemistry applications, the adsorption of CO on metallic electrodes such as Pt, Pd, Au, Ag, RhF, etc. has been extensively studied by in situ infrared spectroscopy Since 1981. In all these studies only three types of CO adsorbates, i. e., linear (2090～2000 cm^-1), bridgrd (2000～1900 cm^-1) or multi-bonded (1900～1800 cm^-1) species, were identified. A different absorbate, twin CO on rhodium (Rh(CO)₂), does exist on the solid/gas interface of highly dispersed Rh or Rhn clusters on supports, this species originating a doublet at …

Preparation Techique Of Foamed Nickel By Electrodeposition, Xihua He, Ronghui Hu, Hanxi Yang, Zhengzhong Zuo

Journal of Electrochemistry

This paper describes the preparation technique and operation conditions for manufacturing foamed nickel by chemilcal pretreament, electrodeposition and heat treatment. The foamed nickel made in this method showed high porosity, uniformity and considerable strength and tenacity,applicable for various secondary battery electrodes.