Open Access. Powered by Scholars. Published by Universities.®

Chemistry Commons™

Open Access. Powered by Scholars. Published by Universities.®

Power and Energy

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 571 - 600 of 1298

Full-Text Articles in Chemistry

Review Of Carbon Materials Energy Storage Mechanism In Lead-Carbon Battery, Le-Ying Wang, Hao Zhang, Chen Hu, Shu-Kai Zhang, Hai-Lei Zhao, Gao-Ping Cao, Wen-Feng Zhang, Yu-Sheng Yang, Xiao-Kang Lai Oct 2014

Review Of Carbon Materials Energy Storage Mechanism In Lead-Carbon Battery, Le-Ying Wang, Hao Zhang, Chen Hu, Shu-Kai Zhang, Hai-Lei Zhao, Gao-Ping Cao, Wen-Feng Zhang, Yu-Sheng Yang, Xiao-Kang Lai

Journal of Electrochemistry

The traditional lead-acid batteries are mainly used for automobile and various internal combustion engine starting, wireless communication base stations and renewable energy storage; however, their negative plates are easily sulfated under partial-state-of-charge duty, then their charging capacity and cycle life are greatly reduced. Lead-carbon battery is a new type of lead-acid battery, in which a carbon material with high specific surface area and conductivity is added into a negative plate, and has excellent rate discharge performance and higher PSoC cycle life. Lead-carbon battery has a good application prospect in energy storage and hybrid electric vehicle, so these years the study …

Go to article

Determination Of Folic Acid By Composite Film Electrode Modified With Poly-Alizarin Red And Multi-Walled Carbon Nanotubes, Xue-Ping Du, Tong-Fang Lou, Ying Dong, Jian-Ying Qu Oct 2014

Determination Of Folic Acid By Composite Film Electrode Modified With Poly-Alizarin Red And Multi-Walled Carbon Nanotubes, Xue-Ping Du, Tong-Fang Lou, Ying Dong, Jian-Ying Qu

Journal of Electrochemistry

The novel modified electrode was fabricated by electropolymerizing alizarin red onto the surface of multi-walled carbon nanotubes on glassy carbon electrode surface, which exhibited good electrocatalytic activity for folic acid. The experimental results showed that the reduction peak current of folic acid at -0.63 V was linear to its concentration over the range of 1.25×10-6 ~ 4.00×10-5 mol·L-1 in the optimized experimental conditions (R = 0.9985). Test for recovery was carried out by standard addition method, and the recovery ratios were in the range of 92.0% ~ 102.0%. The modified electrode was prepared simply with excellent stability, …

Go to article

Electro-Catalytic Properties Of Β-Pbo2/Sb-Sno2/Ti Electrode On Phenol Oxidation, Peng Li, Yue-Min Zhao, Li-Zhang Wang, Yan-Le Zhang, Zhao-Qing Lu Oct 2014

Electro-Catalytic Properties Of Β-Pbo2/Sb-Sno2/Ti Electrode On Phenol Oxidation, Peng Li, Yue-Min Zhao, Li-Zhang Wang, Yan-Le Zhang, Zhao-Qing Lu

Journal of Electrochemistry

The combination technology of brush pyrolysis and electroplating was employed in the preparation of β-PbO2/Sb-SnO2/Ti electrode. X-ray Diffraction (XRD) and Scanning Electron Microscope (SEM) results showed that the Sb-SnO2 as an interlayer would restrain the formation of lead fluoride and the crystallization degree on the electrode surface could be as high as 100%. The grain size was calculated by Scherrer formula to be 25.2 nm and the agglomeration of lead dioxide was effectively eliminated. The potential span of diffusion control phase, oxygen evolution potential, Tafel slope for the β-PbO2/Sb-SnO2/Ti electrode during …

Go to article

Electrochemical And Spectroscopic Studies Of Ethanol Oxidation On Nano-Cubic Pt Modified By Tin Adatoms, Lu Rao, Bin-Wei Zhang, Yan-Yan Li, Yan-Xia Jiang, Shi-Gang Sun Oct 2014

Electrochemical And Spectroscopic Studies Of Ethanol Oxidation On Nano-Cubic Pt Modified By Tin Adatoms, Lu Rao, Bin-Wei Zhang, Yan-Yan Li, Yan-Xia Jiang, Shi-Gang Sun

Journal of Electrochemistry

The nano-cubic Pt modified by tin (Sn) was synthesized and used to investigate the role of this adatom played in the ethanol oxidation. The onset potential of ethanol oxidation was significantly shifted negatively which can be forward about 300 mV when the coverage of Sn (θSn)was 0.9. The electrtochemical in situ FTIR result demonstrated that the amount of CO2 increased first, and then decreased with θSn increased, and reached the maximun when θSn was 0.38. Furthermore, the formation of acetic acid could be observed at very low potential (-0.05 V) after modifying Sn adatom, and the amount of acetic …

Go to article

Preparation Of Pt/Dna-Mwcnts/Gc Electrode And Its Electrocatalytic Activity Toward H2O2 Reduction, Li-Li Fan, Li-Na Wu, Zhi-Yu Qu, Dan-Feng Liu, Jun-Ming Zhang, Si-Ming Fan, You-Jun Fan Oct 2014

Preparation Of Pt/Dna-Mwcnts/Gc Electrode And Its Electrocatalytic Activity Toward H2O2 Reduction, Li-Li Fan, Li-Na Wu, Zhi-Yu Qu, Dan-Feng Liu, Jun-Ming Zhang, Si-Ming Fan, You-Jun Fan

Journal of Electrochemistry

The DNA-multi-walled carbon nanotubes (MWCNTs)/glassy carbon (GC) electrode was prepared by modifying the DNA functionalized MWCNTs composite on a GC electrode. A novel non-enzymatic H2O2 sensing electrode was fabricated by electrodepositing Pt nanoparticles on the DNA-MWCNTs/GC electrode. The modified electrodes were characterized by scanning electron microscope (SEM). The response properties of the sensing electrode to H2O2 were investigated by cyclic voltammetry and chronoamperometry. The results indicated that the sensing electrode exhibited a good linear relationship between response current and H2O2 concentration in the range of 0.04 ~ 18.07 mmol·L-1 with …

Go to article

Electrochemical Catalysis: A Dft Study, Li Li, Zi-Dong Wei Aug 2014

Electrochemical Catalysis: A Dft Study, Li Li, Zi-Dong Wei

Journal of Electrochemistry

In this review, we focus on achievements in electro-catalysis based on the density function theory study. The relationships among the electrode potential, electronic structure of catalysts and electro-catalytic activity are summarized in three parts: the adsorption and desorption of species, electron transfer, and stability of catalysts. The electrode potential and the electronic structure (d-band center or Fermi (HOMO) energy) of catalysts significantly influence the formation, adsorption and desorption of surface species on electrode. The electro-catalytic activity can be improved by modulating the electrode potential and electronic structure of catalysts.

Go to article

Electrocatalytic Oxidation Of Formate On Pd-Cu/C - Effect Of Dealloying Pretreatment, Kun Jiang, Ye Wang, Tao Lin, Wen-Bin Cai Aug 2014

Electrocatalytic Oxidation Of Formate On Pd-Cu/C - Effect Of Dealloying Pretreatment, Kun Jiang, Ye Wang, Tao Lin, Wen-Bin Cai

Journal of Electrochemistry

Carbon supported highly dispersed Pd-Cu nanoalloy catalyst toward formate electrooxidation is prepared via one-pot synthesis by using ethylene glycol as the reducing agent and sodium citrate as the stabilizer. The as-prepared catalyst is structurally characterized by TEM and XRD. The Cu dealloyment is carried out through repetitive potential cycling of the Pd-Cu/C catalyst in an acidic solution. The dealloying effect on the performance of the Pd-Cu/C is investigated by using cyclic voltammetry and chronoamperometry, and the surface structural change of Pd-Cu/C is probed by in situ ATR-IR measurement. The results show that the as-prepared Pd-Cu/C processes a better long-term stability …

Go to article

Synthesis Of Silver Nanoparticles Supported On Graphene Quantum Dots For Oxygen Reduction Reaction, Jian Ju, Wei Chen Aug 2014

Synthesis Of Silver Nanoparticles Supported On Graphene Quantum Dots For Oxygen Reduction Reaction, Jian Ju, Wei Chen

Journal of Electrochemistry

Silver-based catalysts have been extensively investigated as the platinum substituted catalysts due to their high catalytic efficiency, low cost and long-term durability. In this study, the surfactant-free silver nanoparticles supported on graphene quantum dots were synthesized through a facile approach without addition of any other protecting ligands and reducing agents. The “surface-clean” silver nanoparticles had remarkable electrocatalytic performance towards oxygen reduction reaction (ORR) with the most efficient four-electron transfer process. Compared with commercial Pt/C catalyst, the hybrid nanoparticles showed comparable catalytic performance for ORR but much higher tolerance to methanol. Such silver nanoparticles supported on graphene quantum dots may have …

Go to article

Preparation And Lithium Storage Performance Of Sn-Snsb Nanoparticles, Yao Xiao, Jiao-Hong Wu, Qi Wang, Ling Huang, Jun-Tao Li, Shi-Gang Sun Aug 2014

Preparation And Lithium Storage Performance Of Sn-Snsb Nanoparticles, Yao Xiao, Jiao-Hong Wu, Qi Wang, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

Tin was widely studied as alternative anode material to carbon for lithium-ion batteries thanks to its much higher theoretical capacity. However, a pure tin electrode suffers severely from its poor cycleability due to mechanical fatigue caused by volume change during lithium insertion and extraction processes. Tin-based alloy may improve the cycleability property of tin electrode. In this article, we report facile synthesis of spherical Sn-SnSb nanopartciles using a simple solvent-thermal approach. It is amazing to find that the spherical Sn-SnSb nanoparticles can circumvent volume changes effectively during charge-discharge process. Electrochemical discharge/charge results show that the spherical Sn-SnSb nanoparticles electrode exhibits …

Go to article

Electrochemical Fabrication Of Two-Dimensional Flower-Like Pt Nanostructures For Methanol Electrocatalytic Oxidation, Xia Wang, Jun Hu, Yong-Jun Li Aug 2014

Electrochemical Fabrication Of Two-Dimensional Flower-Like Pt Nanostructures For Methanol Electrocatalytic Oxidation, Xia Wang, Jun Hu, Yong-Jun Li

Journal of Electrochemistry

Two-dimensional flower-like Pt nanostructures (2D FPNs) were fabricated on glassy carbon substrates by galvanostatical electrochemical technique. The electrolyte was the HAuCl4 + HClO4 aqueous solution without addition of any structure-directing organic reagent, which made as-prepared Pt nanostructures cleaner, exhibiting much higher reactivity. Scanning electron microscopic images revealed that 2D FPNs were spherical Pt nano-flowers constructed by the smallest building blocks, nano-leaves. The number density of spherical Pt nano-flowers can be tuned by controlling the electrodeposition time. High resolution transmission electron microscopic images indicated that each nano-leaf was formed by growing along Pt(111) direction. Electrocatalytic activities of as-prepared 2D …

Go to article

A Sensitive And Label-Free Electrochemical Aptasensor Based On Signal Amplification Of Carbon Nanotubes, Chun-Yan Deng, Hui-Min Fan, Juan Xiang, Yuan-Jian Li Aug 2014

A Sensitive And Label-Free Electrochemical Aptasensor Based On Signal Amplification Of Carbon Nanotubes, Chun-Yan Deng, Hui-Min Fan, Juan Xiang, Yuan-Jian Li

Journal of Electrochemistry

A label-free electrochemical sensing electrode for highly sensitive detection of adenosine was constructed based on the signal amplification of carbon nanotubes (CNTs). The change in the interfacial feature of the modified electrode was characterized by electrochemical impedance spectroscopy. Using [Ru(NH3)6]3+ as the signaling moiety, adenosine with concentrations as low as 0.027 nmol·L-1 can be selectively detected. Additionally, the fabrication of this present aptasensor was simple, time-saving and cost-effective. Compared with other reported aptasensors, the proposed aptasensor had advantages of excellent sensitivity, selectivity and simplicity, which plays a potential role in development of aptasensor.

Go to article

Investigation Of The Dynamics Of Photocarriers During Photoelectrochemical Water Splitting By Combination Of Photoelectrochemistry And Transient Absorption Spectroscopy, Wen-Hua Leng Aug 2014

Investigation Of The Dynamics Of Photocarriers During Photoelectrochemical Water Splitting By Combination Of Photoelectrochemistry And Transient Absorption Spectroscopy, Wen-Hua Leng

Journal of Electrochemistry

Semiconductor photoelectrochemical hydrogen production is an important and promising technology for utilizing solar energy. The efficiency of hydrogen production depends on the efficiencies of separation and transport of photo-generated carriers. A deep understanding of the behavior of these processes has guiding significance for designing efficient solar hydrogen device. photoelectrochemical and transient absorption spectroscopy methods are powerful tool for studying the microscopic dynamics and mechanism of photocatalytic reaction. This review describes the part of the latest results of the author regarding the semiconductor photoelectrochemical hydrogen production obtained by these methods,and the problems and future research priorities in this field are proposed.

Go to article

Effecting Of Dissolved Oxygen On Microbial Fuel Cells Based On Pseudomonas Aeruginosa, Chang-Li Cao, Li-Xiang Chen, Ran-Ran Wu, Ken-Lin Chang, Feng Zhao Aug 2014

Effecting Of Dissolved Oxygen On Microbial Fuel Cells Based On Pseudomonas Aeruginosa, Chang-Li Cao, Li-Xiang Chen, Ran-Ran Wu, Ken-Lin Chang, Feng Zhao

Journal of Electrochemistry

In this work, the reaction between the electron shuttle secreted by Pseudomonas aeruginosa and anode was studied by measuring cyclic voltammogram and open circuit potential. The effect of dissolved oxygen on the oxidation reaction of anode was explored. It was demonstrated that the reaction was a diffusion-controlled and reversible process. The anode was a little affected when the dissolved oxygen of inocula was low (0 ~ 1.6 mg·L-1). The polarization curves showed that the current output of microbial fuel cells decreased 7% with the impact of dissolved oxygen.

Go to article

Recent Progress In The Mechanistic Understanding Of Formic Acid Oxidation On Pt Electrode, Jie Xu, Dao-Chuan Jiang, Dong Mei, Zheng-Da He, Yan-Xia Chen Aug 2014

Recent Progress In The Mechanistic Understanding Of Formic Acid Oxidation On Pt Electrode, Jie Xu, Dao-Chuan Jiang, Dong Mei, Zheng-Da He, Yan-Xia Chen

Journal of Electrochemistry

This article reviews the recent progress in understanding of the mechanisms for formic acid oxidation on Pt electrode. There are two pathways for formic acid oxidation on Pt electrode: (1) Indirect Pathway through which HCOOH is oxidized to CO2 through COad intermediate. This pathway contributes only 1% of the total current; (2) Direct Pathway where HCOOH is oxidized directly to CO2. The results from IR Spectroscopy, single-crystal electrochemistry and DFT calculation all support that the bridge-bonded formate is neither the intermediate of direct pathway nor the precursor for COad formation in indirect pathway. Possible mechanism …

Go to article

Preparation Of Pt-Tio2/Graphene Composites With High Catalytic Activity Towards Methanol Oxidation And Oxygen Reduction Reaction, Li Qi, Ying Yin, Wen-Guang Tu, Bing-Bing Wu, Zhao-Sheng Wang, Jian-Guo Liu, Jun Gu, Zhi-Gang Zou Aug 2014

Preparation Of Pt-Tio2/Graphene Composites With High Catalytic Activity Towards Methanol Oxidation And Oxygen Reduction Reaction, Li Qi, Ying Yin, Wen-Guang Tu, Bing-Bing Wu, Zhao-Sheng Wang, Jian-Guo Liu, Jun Gu, Zhi-Gang Zou

Journal of Electrochemistry

A series of graphene-supported TiO2 nanoparticles (TiO2/G) with different TiO2 contents were prepared by a facile hydrothermal method, and then the Pt-TiO2/G catalysts were successfully prepared by reducing Pt-precursor with microwave technique. Compared with Pt-G catalysts, the catalytic performance toward oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR) of Pt-TiO2/G catalysts was improved due to the addition of TiO2. However, the excessive TiO2 would lead to a poor catalytic performance of Pt-TiO2/G catalysts because of the low electrical conductivity of TiO2.

Go to article

Horseradish Peroxidase-Attapulgite Clay Nanocomposites: Fabrication And Application To Sensing The Extracellular H2O2 Released From Cells, Ping Wu, Chen-Xin Cai Jun 2014

Horseradish Peroxidase-Attapulgite Clay Nanocomposites: Fabrication And Application To Sensing The Extracellular H2O2 Released From Cells, Ping Wu, Chen-Xin Cai

Journal of Electrochemistry

The nanostructured attapulgite clay was employed as a support matrix for immobilizing horseradish peroxidase (HRP). FTIR and electrochemical methods demonstrated that HRP had been effectively assembled on attapulgite surface with the formation of HRP-attapulgite nanocomposites. The HRP-attapulgite hybrid was deposited on the glassy carbon (GC) electrode forming the HRP-attapulgite/GC electrode. Cyclic voltammetric results showed a pair of well-defined redox peaks, which were ascribed to direct electron transfer (DET) of HRP, with the formal potential E0′ = -335 mV (vs. SCE) in the phosphate buffer solution (PBS, pH 7.0). The dependence of E0′ on solution pH indicated …

Go to article

The Ionic Diffusion Model For The Solid Oxide Cathode And Its Verification By The Electrolysis Of Ta2O5 In Molten Cacl2, Hua-Lin Chen, Zhi-Yong Wang, Xian-Bo Jin, George Z. Chen Jun 2014

The Ionic Diffusion Model For The Solid Oxide Cathode And Its Verification By The Electrolysis Of Ta2O5 In Molten Cacl2, Hua-Lin Chen, Zhi-Yong Wang, Xian-Bo Jin, George Z. Chen

Journal of Electrochemistry

The deoxidation speed of a solid oxide cathode in molten CaCl2 can be estimated by the PRS steady diffusion model of O2-, which correlates the deoxidation speed with the precursor porosity, P, the metal-to-oxide molar volume ratio, R, and the cathode volume shrinkage S. The PRS model indicates that the porosity of the oxide cathode has important influence on the deoxidation speed, and provides a very simple equation for the prediction of the optimal cathode porosity. For the electrolysis of Ta2O5, the porosity of the cathode is better to be within 50%. …

Go to article

23Na Mas Nmr Spectroscopic Study Of Na2Mnpo4F As Cathode Material For Sodium-Ion Battery, Xu Hou, Gui-Ming Zhong, Xiao-Chen Lin, Zi-Geng Liu, Xiao-Biao Wu, Yong Yang Jun 2014

23Na Mas Nmr Spectroscopic Study Of Na2Mnpo4F As Cathode Material For Sodium-Ion Battery, Xu Hou, Gui-Ming Zhong, Xiao-Chen Lin, Zi-Geng Liu, Xiao-Biao Wu, Yong Yang

Journal of Electrochemistry

The Na2MnPO4F is one of the promising cathode materials for the sodium ion batteries. In the paper, we employed the ex situ X-ray diffraction and solid state NMR techniques to study the charge and discharge processes of this material, including the crystal structure and sodium sites changes. The ex situ x-ray diffraction patterns showed that two new diffraction peaks could be observed at 31o and 36o indicating an intermediate phase formed with the extraction of Na+. From the 23Na MAS NMR spectrum of the material, three peaks were seen at -209 …

Go to article

Effects Of Oxygen Coverage And Hydrated Proton Model On The Dft Calculation Of Oxygen Reduction Pathways On The Pt(111) Surface, Li-Hui Ou, Sheng-Li Chen Jun 2014

Effects Of Oxygen Coverage And Hydrated Proton Model On The Dft Calculation Of Oxygen Reduction Pathways On The Pt(111) Surface, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

DFT calculation is used to study various possible steps in the oxygen reduction reaction (ORR), including the adsorption and dissociation process of O2 and the serial protonation process of dissociated products to form H2O on the Pt(111) surface. By using slabs of different sizes, and different numbers of pre-adsorbed oxygen atoms, the coverage effects on the pathways are investigated. The calculated results using different hydrated proton models are also compared. It is shown that the initial step of the ORR is the formation of a protonated end-on chemisorbed state of OOH*, which can transform to an unprotonated …

Go to article

Preparation And Electrochemical Performances Of Cofe2O4/Gns Nanocomposites As Anode Material For Lithium Ion Battery, Mo-Chao Cai, Sen-Rong Cai, Ming-Sen Zheng, Quan-Feng Dong Apr 2014

Preparation And Electrochemical Performances Of Cofe2O4/Gns Nanocomposites As Anode Material For Lithium Ion Battery, Mo-Chao Cai, Sen-Rong Cai, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The CoFe2O4/GNS was synthesized by a simple one-pot solvothermal method. The results obtained by X-ray diffraction (XRD) and transmission electron microscopy (TEM) showed that the CoFe2O4 particles with sizes of 15 nm dispersed on the surface of graphene uniformly. Electrochemical tests indicated that the CoFe2O4/GNS nanocomposite exhibited excellent cyclic stability with almost 95.8% capacity retention after 100 cycles at the current density of 500 mA·g-1 and delivered a high reversible capacity of 482 mAh·g-1 at the current density of 2 A·g-1.

Go to article

Effects Of Carbon Interlayer On Electrochemical Performance Of Lithium-Sulfur Cell, Jin-Peng Yu, Ming Zhang, Fei Ding, Zhi-Yuan Tang, Xing-Jiang Liu Apr 2014

Effects Of Carbon Interlayer On Electrochemical Performance Of Lithium-Sulfur Cell, Jin-Peng Yu, Ming Zhang, Fei Ding, Zhi-Yuan Tang, Xing-Jiang Liu

Journal of Electrochemistry

Three kinds of conductive carbon films were prepared with Super-P (SP), KB and MWCNTs, and then the as-prepared carbon films were applied as an interlayer between a sulfur electrode and a separator for constructing a coin-type lithium-sulfur (Li-S) cell, respectively. The assessment results show that all the cells delivered the reversible capacities higher than 800 mAh·g-1 after 40 cycles when the sulfur loading was up to 80% (by mass) in the sulfur electrode. Due to significant differences of physical properties among the carbon materials, the cell with a KB interlayer exhibited higher electrochemical polarization; the cycling performance of the …

Go to article

Electrocatalytic Oxidation Of Glycerol At The Platinum Electrode Modified With An Nd-Fe-Moo42- Cyano-Bridged Mixed Coordination Polymer, Yong-Jun Ma, Yu-Xiu Tian, Jing Liu, Min Zhou, Jing Ding, Zhi-Mei Jin, Xiang-Mei Wang Apr 2014

Electrocatalytic Oxidation Of Glycerol At The Platinum Electrode Modified With An Nd-Fe-Moo42- Cyano-Bridged Mixed Coordination Polymer, Yong-Jun Ma, Yu-Xiu Tian, Jing Liu, Min Zhou, Jing Ding, Zhi-Mei Jin, Xiang-Mei Wang

Journal of Electrochemistry

A platinum electrode decorated with the ordered Nd-Fe-MoO42- cyano-bridged mixed coordination polymer was successfully prepared by electrodeposition in virtue of the lyotropic liquid crystal soft template methods, and electrocatalytic oxidation behavior of glycerol was investigated on the chemically modified electrode by cyclic voltammetry. The influences of experimental factors such as the concentrations of H+ and SO42- in electrolytes, glycerol concentration and scan rate on the electrocatalytic activity of glycerol at the modified electrode were also studied. It indicated that the proper amount of SO42- in weakly acidic electrolyte could help to improve the …

Go to article

Synthesis Of Platinum Nanocrystallites And Possible Electrocatalytic Properties For Methanol, Lei-Lei Lu, Bao-Zhong Du, Sha Sun, Jin-Fen Niu, Jie Zhao Apr 2014

Synthesis Of Platinum Nanocrystallites And Possible Electrocatalytic Properties For Methanol, Lei-Lei Lu, Bao-Zhong Du, Sha Sun, Jin-Fen Niu, Jie Zhao

Journal of Electrochemistry

Platinum nanocrystallites were synthesized by the colloidal method using oxamide as the stabilizer. The morphologies and electrocatalytic performances for methanol of platinum nanocrystallites prepared at different pH values and with different reactant ratios of precursor and stabilizer were investigated. It was found that the platinum nanocrystallites synthesized at pH=5 and with the reactant ratio of 1:20 showed the best electrocatalytic activity for methanol. The peak current density reached up to 1709 μA·cm-2. Furthermore, the electrocatalytic activity of platinum nanocrystallites for methanol reduced significantly although the cyclic voltammograms in the blank solution were not obviously changed after exposing in …

Go to article

Effect Of Temperature On The Self-Humidifying Open-Cathode Proton Exchange Membrane Fuel Cell, Si-Chen Zhao, Ben Wang, Qiu-Hong Jia, Ming Han, Yu-Hong Xie Apr 2014

Effect Of Temperature On The Self-Humidifying Open-Cathode Proton Exchange Membrane Fuel Cell, Si-Chen Zhao, Ben Wang, Qiu-Hong Jia, Ming Han, Yu-Hong Xie

Journal of Electrochemistry

Based on the experiments about the output characteristics of a home-made temperature-controlled PEMFC system with atmospheric pressure and no external humidifying condition in different loading voltages and operating temperatures, the optimum operating temperature at different loading voltages can be obtained by tracking the output characteristics of PEMFC operating over a range of temperatures. By analyzing the fitted data the kinetic parameters are evaluated and the effect of different operating temperatures on the PEMFC performance is discussed from a view of electrode kinetics.

Go to article

Preparation Of Pt/H-Tio2 Catalyst With Improved Catalytic Performance For Methanol Electrooxidation, Jin Han, Zhi-You Zhou, Qiang Wang, Miao-Qiang Lv, Chi Chen, Shi-Gang Sun Apr 2014

Preparation Of Pt/H-Tio2 Catalyst With Improved Catalytic Performance For Methanol Electrooxidation, Jin Han, Zhi-You Zhou, Qiang Wang, Miao-Qiang Lv, Chi Chen, Shi-Gang Sun

Journal of Electrochemistry

White TiO2 nanorods were synthesized by hydrothermal method with TiCl4 as a precursor. As-synthesized TiO2 nanorods were further subjected to high-temperature (550 oC) heat treatment for 2 h under H2 atmosphere to prepare gray black hydrogen-treated TiO2 (H-TiO2) nanorods with oxygen vacancies and Ti3+ interstitial atoms. The Pt nanoparticles of 1.9 nm were supported on these two types of TiO2 nanorods to form Pt/TiO2 and Pt/H-TiO2 catalysts. XRD data indicates that the crystal structure of TiO2 was still reserved as rutile after hydrogen treatment, but the surface …

Go to article

Electro-Catalytic Oxidation Of Hydrogen Peroxide On Au/ L-Methionine /Gc Electrode, Jian-Feng Fan, Xue-Mei Luo, Jing Li, Lou-Zhen Fan Apr 2014

Electro-Catalytic Oxidation Of Hydrogen Peroxide On Au/ L-Methionine /Gc Electrode, Jian-Feng Fan, Xue-Mei Luo, Jing Li, Lou-Zhen Fan

Journal of Electrochemistry

The modified electrodes have been fabricated by generation of Au nanoparticle chains, which was produced by reaction between HAuCl4 and sodium citrate without any additional capping agents or surfactants. The self-assembled Au nanoparticles were attached to the surface of glassy carbon electrode (GCE) layer by layer, using L-methionine (L-Met), thiourea (TU), allyl thiourea (ATU) and polyvinylpyrrolidone (PVP) as a crosslinking agent, respectively. The experimental results showed that the electrochemical performance of the different modified electrodes varied in [Fe(CN)6]3-/4- solution. The Au/L-Met/GCE exhibited an excellent electrochemical property, which is superior to other modified electrodes. In addition, the catalysis …

Go to article

An Equivalent Circuit Model For Redox Flow Battery Stack, Dong-Jiang You, Hua-Min Zhang Apr 2014

An Equivalent Circuit Model For Redox Flow Battery Stack, Dong-Jiang You, Hua-Min Zhang

Journal of Electrochemistry

This paper introduces an equivalent circuit model for a redox flow battery stack. The model combines the electrochemical reaction of the battery cell and the shunt current of the battery stack. An all-vanadium redox flow battery stack of 1kW rated output power is tested through transient response and self-discharge experiments. All the parameters used for the modeling are obtained. Calculated shunt current and distribution of calculated battery voltage are shown in the results. It is concluded that the impedance of the battery stack can be obtained by the experimental results of the transient response and self-discharge measurements. The capacity lose …

Go to article

Application Of Ionic Liquid Pp14Tfsi In Electrolyte Systems For Rechargeable Mg Batteries, Jin-Jie Zhu, Fei-Fei Wang, Yong-Sheng Guo, Jun Yang, Yan-Na Nuli, Jiu-Lin Wang Apr 2014

Application Of Ionic Liquid Pp14Tfsi In Electrolyte Systems For Rechargeable Mg Batteries, Jin-Jie Zhu, Fei-Fei Wang, Yong-Sheng Guo, Jun Yang, Yan-Na Nuli, Jiu-Lin Wang

Journal of Electrochemistry

A phenolated-based Mg salt was prepared. The mixture of THF and N-methyl-N-butyl-piperidinium bis(trifluoromethanesulfonyl)imide (PP14TFSI) serves as the mixed solvent instead of pure THF for rechargeable Mg batteries systems. This new type of electrolyte system not only has optimal reversibility of Mg, but also owns a wide electrochemical window (2.7 V vs. Mg) and high ionic conductivity (7.77 mS·cm-1). More importantly, the addition of Ionic Liquid suppresses the volatility of THF and improves the safety of rechargeable Mg batteries. The result shows that the mixture of THF and piperidyl-based Ionic Liquid could be regarded as a good solvent candidate …

Go to article

Effect Of Al-Doping In Li-Rich Material Li1.2Mn0.543Co0.078Ni0.155Al0.030O2 For Lithium-Ion Batteries, Xiao-Xi Jin, Yi-Xiao Li, Yong Yang, Zhou-Cheng Wang Apr 2014

Effect Of Al-Doping In Li-Rich Material Li1.2Mn0.543Co0.078Ni0.155Al0.030O2 For Lithium-Ion Batteries, Xiao-Xi Jin, Yi-Xiao Li, Yong Yang, Zhou-Cheng Wang

Journal of Electrochemistry

The Al-doped 0.5Li2MnO3·0.5Li(Mn0.4Co0.2Ni0.4)O2 compounds were successfully synthesized as cathode materials for lithium-ion batteries. The pristine and Al-doped materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), inductively coupled plasma-atomic emission spectrometry (ICP-AES) and laser Raman spectroscopy. The results indicated that all the prepared materials were indexed as a hexagonal structure with R-3m space group, and Al element had been introduced into lattice. When cycled at 180 mA·g-1 (1 C-rate), the capacity retention of 4% (by mole) Al-doped 0.5Li2MnO3·0.5Li(Mn0.4Co0.2Ni …

Go to article

Preparation Of High Performance Porous Silicon Powders By Etching Al-Si Alloy In Acid Solution For Lithium Ion Battery, Shi-Ji Hao, Chun-Li Li, Kai Zhu, Ping Zhang, Zhi-Yu Jiang Feb 2014

Preparation Of High Performance Porous Silicon Powders By Etching Al-Si Alloy In Acid Solution For Lithium Ion Battery, Shi-Ji Hao, Chun-Li Li, Kai Zhu, Ping Zhang, Zhi-Yu Jiang

Journal of Electrochemistry

Porous silicon powders prepared by etching Al-Si alloy using an acid solution was reported in the first time. The morphology and structure of as-obtained material were investigated using scanning electron microscopy (SEM) and X-ray diffraction (XRD) method. It was found that the spongy porous silicon powders presented well crystalline structure and consisted of nano-Si particles. The particle size of porous Si powders was about 20 μm, and the specific surface area was 102.7 m2·g-1. The electrochemical properties of porous silicon powders were evaluated as an anode material for lithium ion batteries. The material proportion in the …

Go to article

First Prev Next Last