Chemistry Commons^™

Investigation Of Portland Limestone Cement Blended With Biochar From Downdraft Gasification: Hydration Kinetics, Microstructure, Rheology, And Performance Mechanisms, Ugochukwu Ewuzie, Paul C. Ani, Abdulkareem O. Yusuf, Joseph D. Smith, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

The widespread adoption of Portland Limestone Cement (PLC) in U.S. concrete production has necessitated research into commercially available supplementary cementitious materials (SCMs) for formulating high-performance, low-carbon blended binders with PLC. This study investigated the influence of biochar (BC) in biochar-PLC composites (CBCs), focusing on hydration kinetics, microstructure, rheology, pore-solution chemistry, compressive strength, and the underlying mechanisms. Biochar was produced via downdraft gasification at 850 °C and incorporated into PLC at 5, 7, and 10% substitution by mass. Isothermal calorimetry and hydration data modeled using the Knudsen equation revealed that BC retarded early hydration but improved hydration degree and later-age heat …

Characterization Of The Thermally Driven Red Hue Effect In Coated And Uncoated Concrete Systems: Implications For Post-Fire Assessment In Wildland Urban Interface Communities, Juan C. Palominos Jr

Master's Theses

The increasing frequency and intensity of Wildland-Urban Interface (WUI) wildfires, such as the destructive 2025 Pacific Palisades Fire that destroyed over 6,000 structures, have underscored the urgent need for rapid post-fire safety assessment methodologies. This study sought to quantitatively characterize the Thermally Driven Red Hue Effect (TRHE), a unique, irreversible color shift observed in architectural coatings and concrete substrates, to determine its reliability as a permanent visual record of thermal exposure. Concrete substrates were formulated with three distinct coarse aggregates: gold granite (14.7% Fe), red cinder (22.4% Fe), and green rock (33.6% Fe) and coated with a 20 PVC waterborne …

Thermally Induced Color Changes In Iron Oxide Pigments Used In Architectural Coatings, Han Diep

Master's Theses

The 2025 Palisades Fire was one of the most destructive wildfires in the history of Los Angeles, destroying thousands of structures and severely impacting the communities after. This widespread destruction demonstrated an urgent need for more effective wildfire prevention strategies. Architectural coatings do not only provide aesthetics and protection against environmental conditions but can also function as a thermal indicator when a fire breaks out. This study examines the thermally induced color transformation of iron oxide pigments, commonly used in earthtone paint, to provide information relevant to CAL FIRE for improved analysis of wildland-urban interface (WUI) fire behavior and mitigation …

Modulating Electronic Structure With Linearly Fused Pyrazine Units For High-Voltage And Stable Zinc-Organic Batteries Cathode, Min-Jian Zhao, Li-Bin Zhang, Jin-Tao Wang, Kun Ding, Hai-Mei Liu, Yong-Gang Wang

Journal of Electrochemistry

High-voltage n-type organic cathode materials are critical for constructing zinc-organic batteries (ZOBs) with high energy density and long cycle life. However, the intrinsically unfavorable electronic structures and relatively high LUMO energy levels of most n-type materials often lead to sluggish kinetics, high solubility, and suboptimal discharge voltages (< 0.8 V). Here, we design a small molecule, quinoxalino[2’,3’:5,6]pyrazino[2,3-f][1,10]phenanthroline (DPQP), as a ZOB cathode by introducing locally electron-deficient motifs into the conjugated backbone of aromatic compounds. The linearly fused pyrazine units extending the pyrazine–benzene framework effectively optimize the electronic structure, thereby significantly enhancing the discharge voltage. Meanwhile, the expanded π-conjugated plane suppresses dissolution and accelerates charge-transfer kinetics. Benefiting from these features, the DPQP electrode exhibits an exceptional increase in average operating voltage from 0.61 V to 1.07 V (vs. Zn²⁺/Zn) at 0.1 A·g^–1, with an overpotential of only 140 mV. Notably, no discernible voltage decay occurs as the current density increases, indicating rapid and highly reversible redox kinetics. Furthermore, the DPQP cathode delivers outstanding cycling stability, maintaining over 2000 h of continuous operation at 0.1 A·g^{–1 …}

(Co,Ni,Mn,Cu,Zn)O High-Entropy Oxide Nanotubes As Efficient Bifunctional Electrocatalyst For Oxygen Evolution And Hydrazine Oxidation Reactions, Pan-Yan Chen, Wan-Wan Wu, Heng Bian, Wei-Wei Li, Xin-Sheng Zhao, Lu Wei

Journal of Electrochemistry

High-entropy oxides (HEOs) present significant scientific challenges in both design and synthesis due to their multielement and high-entropy nature, which involves complex combinations of multiple metal cations and oxygen anions, typically arranged in equimolar ratios to achieve structural stability. Herein, one-dimensional (Co,Ni,Mn,Cu,Zn)O high-entropy oxide nanotubes (HEO-NTs) are fabricated by means of a gradient electrospinning strategy with a tailored polyvinyl alcohol (PVA) molecular weight distribution and controlled pyrolysis. Benefiting from the HEO features and the synergistic effect of multicomponent sites, the as-synthesized (Co,Ni,Mn,Cu,Zn)O HEO-NTs exhibit exceptional bifunctional electrocatalytic activity for the oxygen evolution and hydrazine oxidation reactions (OER/HzOR). This study offers …

Surface Directed Microwave Assisted Fabrication Of Znmn2o4 And Its Composite As Anode Materials For Lithium Ion Battery, Anirudh Singh

Electronic Theses & Dissertations

The Lithium-ion batteries (LIBs) are widely utilized in portable electronics and electric/hybrid electric vehicles. However, the limited theoretical capacity of graphite (372 mA h g⁻¹) restricts further advancements. In our recent work, a series of ZnMn₂O₄ materials with various additives were synthesized using the microwave reaction method and evaluated as anodes for LIBs. Additives such as 2-methylimidazole (2MIM), polyvinyl alcohol (PVA), and cetyltrimethylammonium bromide (CTAB) were employed to prepare ZnMn₂O₄ with distinct morphologies. Our findings revealed that ZnMn₂O₄  with pure phases was achieved when 2MIM and CTAB were used as additives. …

Engineering Silicone Magnetic Fluids For Localized Radiation Attenuation During Ocular Melanoma Brachytherapy, Zachary L. Caprow

All Dissertations

Ocular melanoma is commonly treated using plaque brachytherapy; however, radiation-induced damage to healthy ocular tissues frequently results in partial or complete vision loss. This work investigates the development of an injectable, magnetically responsive silicone magnetic fluid designed to localize adjacent to the tumor and attenuate low-energy gamma radiation during treatment.

The material system consists of iron oxide nanoparticles surface-functionalized with a siloxane polymer, in which the nanoparticles provide magnetic responsiveness and radiation attenuation, while the polymer coating ensures colloidal stability, injectability, and biocompatibility. A one-pot synthetic approach was developed wherein a functionalized siloxane polymer containing iron-affinitive groups was reacted with …

Adsorption Of Pfas On Bridged Functionalized Organosilica Materials, Elisha Lawerh Kabutey

Electronic Theses and Dissertations

PFAS are hazardous contaminants that have a devastating impact on human health and the environment. Their hazardous nature has led to the development of various adsorption methods for removing these contaminants from water sources. In this study, functionalized organosilica materials were synthesized from bis[3-(trimethoxysilyl)propyl] amine using the sol-gel method. The surface amino groups of the organosilica were converted into amine hydrochloride groups. Their adsorption properties were evaluated using salts of perfluorooctanoic acid, perfluorooctanesulfonic acid, and perfluorobutanesulfonic acid. Results showed excellent adsorption capacity of the materials. Adsorption of PFAS leads to particle agglomeration and flotation of the spent material. A column …

Insertion Of Noble Metal Free Cathodic Catalyst Layer With Fe-N-C Catalyst For Boosted Performance Of Pemfc, Shi Zhou, Muhammad Tariq, Asif Nadeem Tabish, Muhammad Salman, Fan-Di Ning, Muhammad Rayyan Tayyab, Ran-Ran Peng, Meng-Geng Hao, Wen-Mu Li, Xiao-Chun Zhou

Journal of Electrochemistry

Economical Fe-N-C catalysts are considered as promising alternatives to platinum group metal catalysts for proton exchange membrane fuel cells (PEMFCs). Despite exhibiting robust activity on rotating disk electrodes, their performance within membrane electrode assemblies often experiences limitations, such as decreased O₂ diffusion, high H₂O₂ formation, low proton conduction, and a lower electron transfer number. In this study, key factors, including proton transport, electron conduction, and gas diffusion within air-breathing PEMFCs, have been investigated by adjusting cathode catalyst layer (CCL) compositions. From the experimental results, the optimal peak power density was obtained when the loading of Fe-N-C …

Molecular Catalysts For Electrochemical Nitrogen Activation Toward Sustainable Ammonia Synthesis, Jin-Xiu Han, Hao Xue, Xian-Biao Fu

Journal of Electrochemistry

Homogeneous electrocatalytic nitrogen reduction reaction (NRR) provides a powerful framework to interrogate molecular nitrogen-fixation pathways under mild conditions. By tuning the metal center, ligand architecture, and reaction medium, these systems enable capturing key intermediates and delivering mechanistic insight at the molecular-level resolution. Nevertheless, advances remain constrained by highly reduced operating potentials, intense competition from the hydrogen evolution reaction (HER), limited durability in turnover, and inadequate long-term stability.

In this review, we take electron delivery to the molecular active site as the guiding principle for organizing homogeneous electrochemical N₂ activation and transformation. We classify reported systems into direct electron transfer …

Water-Driven Solid Electrolyte Interphase Governs Continuous-Flow Ammonia Electrosynthesis, Peng-Bo Liu, Sheng-Liang Zhai, Ji Huang, Zhong-Shuo Zhang, Jie Zeng, Shao-Feng Li

Journal of Electrochemistry

Flow-cell architectures have emerged as a powerful platform for continuous and stable lithium-mediated nitrogen reduction (Li-NRR), enabling ambient-condition electrochemical ammonia synthesis and offering a promising alternative to Haber-Bosch processes. However, Li-NRR is exceptionally sensitive to trace water, and even minor variations in water content can profoundly alter interfacial chemistry. Here, we systematically investigate how initial water concentration affects Li-NRR performance in a continuous-flow cell. Excess water drives the formation of a thick solid electrolyte interphase (SEI) layer, which may impede nitrogen access to metallic lithium and hinder lithium-ion transport. As a result, the ammonia Faradaic efficiency collapses from ~61% to …

A Comparative Study Of Tin Electrorefining In Molten Licl–Kcl–Cacl₂: Experimental Two-Electrode Current Control And Theoretical Three-Electrode Potential Control, Bryant Johnson, George Ankrah, Ander Fuller, Devin Rappleye

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

Molten salt electrorefining is a mature technology for metal recovery, yet conventional current‑controlled, two‑electrode operation provides limited electrochemical selectivity and restricted insight into electrode‑specific behavior. In this work, a simplified model is developed to compare current‑controlled two‑electrode electrorefining data with a potential‑controlled three‑electrode electrorefining simulation using tin in molten LiCl–KCl–CaCl₂ as a surrogate for plutonium processing. The model examines anodic and cathodic limitations under fixed‑potential operation and evaluates implications for selectivity, efficiency, and runtime relative to experimentally demonstrated two‑electrode performance. Results indicate that independent potential control enables operation closer to thermodynamic selectivity limits, with the potential to suppress impurity oxidation …

Development Of Cao-Based Heterogeneous Catalysts For The Production Of Palm Oil-Based N-Methyl Diethanolamine Esterquats, Haliza Abdul Aziz

Student Works (2020-2029)

Esterquats are cationic surfactants that are readily biodegradable and exhibit low aquatic toxicity. To produce esterquats via heterogeneous-catalyzed transesterification of methyl ester has become a preferred route to the conventional homogeneous catalysis as the approach can reduce the production cost through catalyst reuse and minimized water footprint through wastewater treatment. Many transesterification reactions catalyzed by pure calcium oxide (CaO) are attributed to its high basicity and it can be derived from a cheap, non-toxic, and environmentally friendly precursor. To enhance the performance and stability of CaO, a series of CaO-based catalysts were synthesized via a wet impregnation method. The catalytic …

Techno-Enviro-Economic Analysis Of Precipitated Calcium Carbonate Production From Carbon Dioxide In Cement Industry Flue Gas And Calcium Hydroxide, Natalia Debora Panggabean, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

CCUS is a technological solution to reduce emissions from the cement industry, which is the second largest CO2-intensive industry. This study aims to analyze technical, economic, and environmental performance of Precipitated Calcium Carbonate (PCC) synthesis in cement industry flue gas. The process simulation includes the CO2 capture system from cement plant, CO2 captured used as feedstock for PCC synthesis process through its reaction with calcium hydroxide. The simulation was carried out using ASPEN Plus software. Technical analysis was performed to determine the CO2 capture efficiency and PCC synthesis efficiency. Economic analysis was conducted to calculate CO2 capture cost and production …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Assessing Passenger Electric Vehicle Growth Strategies And Their Impacts On Electricity Demand Load And Co2 Emissions In Aceh Province To Achieve Net Zero Emission Target By 2060, Taufik Hidayat, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

The electrification of the transport sector is a crucial pathway for achieving Indonesia’s Net Zero Emissions (NZE) target by 2060. This study assesses the potential impact of passenger electric vehicle (EV) penetration on electricity demand and CO2 emissions in Aceh Province through a scenario-based modelling approach. Two policy-aligned scenarios are assessed: a low-penetration (LP) scenario and a high-penetration (HP) scenario. Using the Gompertz model and the ASIF framework, total CO2 emissions were projected from 2020 to 2060. Results show that although higher EV penetration reduces direct emissions from internal combustion engine (ICE) vehicles, total CO2 emissions increase more significantly under …

Synthesis And Performance Evaluation Of Zeolite-Based Ni–Cao For Integrated Co2 Capture And Conversion, Zhang Xinggang

Student Works (2020-2029)

Carbon capture and utilization (CCU) is increasingly being adopted as a strategy to minimize carbon dioxide (CO₂) emissions. Integrated CO₂ capture and utilization (ICCU) is more attractive as it reduces overall cost and energy consumption by eliminating the need for gas compression and transportation. Advances in ICCU and the development of dual functional materials (DFMs) capable of adsorbing and in situ converting CO₂ have attracted increasing attention in both academia and industry, driven by the need for efficient CO₂ utilization pathways. After a detailed analysis of the literature, zeolites have emerged as prominent materials for use as adsorbents and catalyst …

Synthesis And Hydrothermal Evaluation Of Poly(Styrene Phosphonate) For Conformance Control In Geothermal Reservoirs, Sara Mccauley

Miners Solving for Tomorrow Research Conference

As atmospheric carbon dioxide levels continue to rise, geothermal energy has emerged as a promising energy alternative to fossil fuels. A barrier to widespread implementation and energy production efficiency is macro-heterogeneity of the rock matrix. Cracks, void spaces, and flow conduits divert fluid flow away from unswept portions of the geothermal reservoir and can cause cooling of the reservoir. Flow heterogeneity has been treated in oil reservoirs by injecting hydrogel particles that travel preferentially to ultra-high permeability zones and selectively block fluid flow in these regions. We are applying polymer hydrogels that withstand hydrothermal conditions of 225 up to 275°C …

Axial Sulfur-Coordination Engineering Boosting Fe–N–C Catalysts For High-Performance Proton Exchange Membrane Fuel Cells, Lin Lin, Xiu-Xuan Hou, Zhe-Chen Fan, Yi-Xuan Yin, Wei-Yi Zhao, Kai Wei, Yu-Die Zhou, Li-Na Hou, Ying Wang, Hao Wan, Jun-Jie Ge

Journal of Electrochemistry

Fe-N-C catalysts have long suffered from kinetically sluggish oxygen reduction reaction (ORR) due to excessive adsorption strength toward oxygen intermediates and low site utilization. Heteroatom doping effectively accelerates ORR reaction kinetics through electronic structure modulation of metal sites for optimal intermediate adsorption, while chemical vapor deposition (CVD) enhances the turnover frequency (TOF) of active sites. Herein, we developed an FeSNC catalyst featuring abundant FeS₁N₄ sites via a dual-precursor CVD strategy. Experimental and theoretical analyses revealed that S incorporation disrupts the symmetric coordination of active sites, which optimizes OH* adsorption energies from 0.212 eV to 1.194 eV. Moreover, …

Deciphering The Role Of Binder Reaction Exothermicity In Thermal Runaway Of Lithium-Ion Cells, Wen Wen, Jing-Hong Zhou, Hao-Tian Lu, Xing-Gui Zhou

Journal of Electrochemistry

Thermal safety associated with lithium-ion cells as power sources remains a critical industry concern. A comprehensive understanding of how internal exothermic side reactions contribute to temperature rise is fundamental for accurately analyzing thermal runaway processes and predicting the thermal safety of lithium-ion cells. While various side-reactions, such as decomposition of solid electrolyte interphase layer, reaction between anode materials and electrolyte, reaction between cathode materials and electrolyte, and electrolyte decomposition, have been identified as heat generation sources in previous studies, the quantification of these reactions remains insufficiently standardized. Particularly, the impact of heat generation from binder decomposition (most commonly polyvinylidene difluoride) …

Entropy Of Metal/Solution Interfaces: Thermodynamic Framework, Theoretical Models, And Roles Of Interfacial Water, Zeng-Ming Zhang, Zi-Xi Liang, Jun Huang

Journal of Electrochemistry

Entropy is a basic thermodynamic property of the electrical double layer (EDL) at metal/solution interfaces, yet, its definition, measurement, and theoretical treatment are dispersed in the literature, and, in some cases, ambiguous. In this paper, we revisit the thermodynamic theory of EDL, from which two variants of entropy, excess entropy and formation entropy, are obtained and compared. In terms of the formation entropy, two calculation routes are validated in the context of a primitive EDL model, namely, the Gouy-Chapman (GC) model. After clarifying the concepts and calculation routes, we investigate interfacial water effects on the EDL entropy, using a refined …

Chemical Design Strategies For Hybrid Metal Halide Semiconductors With Enhanced Stability And Optoelectronic Properties, Ali Azmy

USF Tampa Graduate Theses and Dissertations

Metal halide semiconductors have rejuvenated the attention of the scientific community for the last two decades owing to their photophysical and electronic properties. However, these materials have some limitations that hinder their commercialization and widespread application. One major limitation of these materials is their instability under ambient and operating conditions of moisture, head, light and radiation exposure. Here, we report multiple chemical design strategies to address the stability issues of these materials while simultaneously maintaining their exceptional optoelectronic properties. Such design strategies allowed the acquisition of the first members of the family of porous metal halide semiconductors which exhibit record …

Microstructural Evolution Of Zirconium Diboride Irradiated With 5–10 Mev Au Ions At Room Temperature And 570 °C, Narrie Loftus, José Olivares, Miguel Crespillo, Esther Enríquez Pérez, Jeremy Watts, Eric W. Bohannan, Gregory Hilmas, William Fahrenholtz, Joseph Graham

Materials Science and Engineering Faculty Research & Creative Works

Zirconium diboride was irradiated with 5 MeV Au^2 + , 7 MeV Au⁴⁺ and 10 MeV Au³⁺ ions at room temperature and 570 °C to doses from 1 to 8 displacements per atom (dpa). Grazing incidence X-ray diffraction (GIXRD) analysis revealed no secondary phase formation. Rietveld analysis of the GIXRD data indicated an accumulation of microstrain at low dpa and room temperature. Dislocations observed in transmission electron microscopy (TEM) cross-sections are likely the main contributor to the microstrain. High dpa and high-temperature samples exhibit lower lattice distortion than lower dpa samples, suggesting the presence of enhanced defect …

Current Research Progress On Electrode Materials For All-Vanadium Redox Flow Batteries, Wen-Qi Wang, Jie Jin, Li-Min Wang, Xin-Yue Liu, Tao Cheng, Yong Hou, Han Xue, Zhi-Yu Wang, Bo Liu, Jia-Bao Liu, Xu-Bin Lu

Journal of Electrochemistry

The redox active species in all-vanadium redox flow batteries (VRFBs) reside in the electrolyte, while the heterogeneous reactions occur on the electrode surface; the electrode is therefore the decisive platform for dynamic adsorption, electron transfer, and ion conversion, especially for the VO²⁺/VO₂⁺ and V²⁺/V³⁺ couples. One of the major challenges for VRFBs is the slow charge transfer in VO²⁺/VO₂⁺ and V²⁺/V³⁺ reactions, mainly caused by poor catalytic performance of electrodes and weak adhesion of catalysts to electrodes. This review focuses on the key challenges and recent …

Triphenylmethane-Derived Levelers For High-Speed Redistribution Layer Copper Electroplating Of Tailored Surface Morphologies, Zi-Hao Song, Wei-Bin Wang, Xiao-Hui Liu, Xiao-Min Han, Yi Zhou, Rui Huang, Yan-Xia Jiang, Zhe Li, Xiao-Wei Liu, Mei-Ling Xiao, Hong-Gang Liao, Wei-Lin Xu, Rong Sun

Journal of Electrochemistry

Redistribution Layer (RDL), composed of layered dielectrics and electroplated copper materials, is a basic structure to rearrange numerous I/O pads on the chip surface in wafer-level advanced packaging. As the key chemicals in electrolyte baths, electroplating additives have undergone continuous development to meet the industrial needs for high-speed and fine-line/fine-pitch applications. Meanwhile, the intricate relationships between additive chemical structures and electroplated copper properties are yet to be well understood. In this work, a pair of triphenylmethane-based dye molecules, i.e., gentian violet (GV) and methyl green (MG), was comparatively investigated as levelers for high-speed RDL copper electroplating. Compared to GV, significantly …

Control Of Pore Nucleation And Rearrangement Kinetics During Aluminium Anodizing In Phosphoric Acid Electrolyte, Ilya V. Roslyakov, Nikita A. Shirin, Dmitry M. Tsymbarenko, Sergei N. Pavlov, Sergey E. Kushnir, Nikolay V. Lyskov, Kirill S. Napolskii

Journal of Electrochemistry

Anodic aluminium oxide (AAO) porous films with an interpore distance of several hundred nanometers are of great interest due to their unique interaction with visible and near-infrared light, and high thermal stability up to 1500 °C. These porous films are prepared by aluminium anodizing at high voltages in weak acids, leading to a slow kinetics of initial stages of porous structure formation. Here, we propose an approach to accelerate AAO formation in electrolytes based on weak acids such as phosphoric acid. Aluminium foils, pre-patterned using first anodizing under different conditions and subsequent selective dissolution of a sacrificial AAO layer, were …

Hybrid Data-Driven Cement-Stabilized Soil Design: An Integration Of Machine Learning, Multi-Objective Optimization, And Life Cycle Assessment, Chikezie Chimere Onyekwena, Yunli Li, Ikenna J. Okeke, Ubani Obinna Uzodimma, Monday Uchenna Okoronkwo, Wenping Wu

Chemical and Biochemical Engineering Faculty Research & Creative Works

Soil stabilization is crucial in geotechnical engineering, yet conventional methods are often time-consuming, resource-intensive, and environmentally unsustainable. Despite growing interest in Machine Learning (ML) and optimization tools for mix design, few studies integrate these methods with decision-making techniques and environmental assessment to support practical implementation. This study proposes a hybrid data-driven framework for predicting strength, optimizing mix compositions, and evaluating environmental impacts via life cycle assessment of cement-stabilized soft soils. Six ML models were evaluated, and the top-performing eXtreme Gradient Boosting (XGB) model was further improved using the Grey Wolf Optimizer (GWO). The optimized XGB-GWO model, integrated with a polynomial …

Performance And Mechanistic Insights Into Cement Systems Modified With Wastewater-Recovered Struvite, Ugochukwu Ewuzie, Rupack R. Halder, Abdulkareem O. Yusuf, Abiodun A. Saka, Godwin I. Ogbuehi, Titus C. Egbosiuba, Damilola A. Daramola, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Struvite, the stable hydration product and primary strength phase in magnesium ammonium phosphate cement (MAPC), derived from wastewater treatment, has recently been utilized as a sustainable additive to Portland cement (PC). However, its impacts on cement hydration kinetics, pore refinement, rheology, and the mechanisms underlying these processes have not been comprehensively studied. This study developed Portland cement-struvite (PCS) systems by replacing PC with 3–20 % struvite (ST wt.%: PCS3–PCS20) and evaluated these processes using isothermal calorimetry, 3D micro-computed tomography (μXCT), time-dependent rheometry, X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR), and the Krstulović-Dabić (K-D) model. The FTIR/XRD confirmed the coexistence …

A Computational Study Of The Chemomechanics Of Paracetamol Polymorphs: Towards Improving Drug Tabletability, Karim Nader Samra

Theses and Dissertations

The mechanical properties of pharmaceutical crystals are of great importance in tablet manufacturing. Also, knowing the mechanical properties of different polymorphs of the same crystal can reduce the overall production cost. In this study, computational work was done via performing density functional theory calculations on 3 paracetamol crystal polymorphs Form I, II, and III. Understanding the chemical bonding helps in predicting the key elastic properties for different crystallographic directions. In Form II, lattice vector C is dominated with the intermolecular hydrogen bond OH…O giving it the stiffest Young Modulus and the least Poisson’s ratio. Then comes the A-Axis which contains …

Development Status And Existing Problems Of Ion-Solvation Membranes For Electrolysis Of Water, Zheng-Yuan Zhou, Yu-Tao Sun, Zheng-Bang Liu, Chuan-Zheng Wang, Yong-Nan Zhou, Xi Luo, Tian-Chi Zhou, Jin-Li Qiao

Journal of Electrochemistry

Ion-solvaing membranes (ISMs) have received extensive attention in recent years as a key component in electrochemical energy conversion and storage devices. This article provides an overview of structural composition, performance advantages, research progress, ion conduction mechanism and existing issues of ISMs, primarily classifying them according to the matrix structure. A detailed analysis of performance enhancement methods, key performance indicators of ISMs and performance influencing factors is also presented. The article contributes to further optimizing the design and application of ion-solvation membranes, providing theoretical support for the development of fields such as hydrogen production through electrolysis of water and electrochemical energy …