Chemistry Commons^™

Uncertainty In Determination Of Hydrogen Diffusion Coefficient In Metal Hydride Electrode Based On The Transition Region Of Diffusion-Controlled Impedance, Xian-Xia Yuan, Nai-Xin Xu

Journal of Electrochemistry

Hydrogen diffusion coefficient in MlNi_3.75Co_0.65 Mn_0.4Al_0.2 metal hydride electrode has been determined with transition region of diffusion-controlled impedance. Multiple solutions were obtained at each data point because of the periodic characteristic of some functions used in the calculation, and the maximum difference between the solutions reached several orders of magnitude. On the other hand, the solutions varied for different data points in the transition region of diffusion-controlled impedance of the same experimental plot. It could be concluded that this method is not so well defined and some modification is required.

The Determination Of The Best Modified Way And Microscopical Analysis For Enzyme/Immunoelectrodes, Sa-Ying Dong, Hong-Ren Wang, Yu-Zhu Gao, Guang-Zhang Chen, Ming-Xiang Lv, Bo-Yi Tian

Journal of Electrochemistry

In this paper, the electrochemical response characteristics of enzyme and immuno electrodes were studied by cyclic voltammetry under different conditions. Our goals were to determine the best modified way of bioelectrode, which was the base of biosensor's application. 30U GOD and 0.8 mg/mL SEC1 antibody were suitable to bioelectrode preparation and detection. The microscopical analysis was finished with scan microscopy.

Preliminary Study On Direct Ethanol Fuel Cell, Shu-Qin Song, Li-Kang Chen, Jian-Guo Liu, Zhao-Bin Wei, Qin Xin

Journal of Electrochemistry

The performance of a direct ethanol fuel cell based on Nafion115 was reported.PtRu/C and Pt/C were used as ethanol anode and oxygen cathode catalysts in a single cell of size 9 cm² .The effects of temperature, oxygen pressure, the flow rate of ethanol, and oxygen, and ethanol concentration were tentatively studied. The experimental results showed that the cell open circuit voltage 0.608 V, the cell voltage 0.329 V at 50 mA/cm², and the peak power density 19.25 mW/cm² were reached under the conditions of T_cell =85 ℃, P_O2 =0.5 MPa, C_ethanol =1.0 mol/L …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Quarterly Progress Report 11/16/01- 2/15/02, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application.

Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with very limited density. The transport of oxygen and corrosion products, their interaction and variation of corrosion/precipitation along the flow are not well understood.

The first subtask of this project involves using a …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this project is to evaluate the effect of hydrogen on cracking of candidate target materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The test materials will undergo appropriate thermal treatments prior to being hydrogen-charged by potentiostatic cathodic polarization technique in a simulated aqueous environment at different temperatures of interest. The specimens, upon completion of testing, will be metallographically examined. Further, the scanning electron microscopy (SEM) will be used to determine the extent and nature of cracking in the specimens tested. The thrust of the proposed …

Thermogravimetric Studies Of Pmma On Silica, Bing Zhang, Frank D. Blum

Chemistry Faculty Research & Creative Works

The thermal degradation of poly(methyl methacrylate) (PMMA) has been studied extensively. It is well accepted that the degradation process is a radical chain reaction involving initiation, depropagation, transfer, and termination reactions. In the degradation process, the factors having observable effects on the decomposition behavior include molecular mass, polydispersity, tacticity, and sample dimensions. The effects of tacticity on the degradation behavior of PMMA were investigated by Kashiwagi et al., Jellinek et al. And Chiamtore et al. The results indicated that both isotactic and syndiotactic PMMA have similar decomposition pathways and activation energies. Isotactic PMMA will decompose at a slightly lower temperature …

Effect Of Polymer-Surface Mobility On Adhesion In Poly(Methyl Methacrylate)-Tape System, Bhavesh C. Gandhi, Frank D. Blum, Lokeswarappa R. Dharani

Chemistry Faculty Research & Creative Works

The interaction between two polymer layers, especially adhesion between them, plays an important role in polymer processing and other applications. Detailed knowledge of the molecular structure and dynamics of polymer interfaces, and how they relate to macroscopic mechanical properties, should help designers construct more functional systems. Unfortunately, there have been few studies where both molecular and macroscopic studies have been performed on similar systems. In previous studies from our group, we have probed the dynamics of poly(methyl acrylate) (PMA) and thermal behavior of poly(methyl methacrylate) (PMMA) on silica. These studies helped us paint a picture for strongly bound molecules on …

Effect Of Oxygen Vacancies On The Magnetic Structure Of The La₀.₆Sr₀.₄Feo3-Δ Perovskite: A Neutron Diffraction Study, Zili Chu, William B. Yelon, Jinbo Yang, William Joseph James, Harlan U. Anderson, Yixiang Xie, Satish K. Malik

Physics Faculty Research & Creative Works

Magnetic interactions in perovskite compounds of the type La_1-xSr_xMO_3-δ (M=3d transition such as Mn and Fe) are presumed to arise through a super exchange between 3d electrons of the magnetic ions via oxygen orbitals. The magnetic structure of La_0.6Sr_0.4FeO_3-δ has been studied with neutron diffraction. Oxygen vacancies were created by annealing samples under various gases including N₂, air and mixtures of CO/CO₂. All La_0.6Sr_0.4FeO_3-δ compounds maintain the rhombohedral structure (space group R3̄c). The air- or oxygen-annealed samples have almost no oxygen …

Experimental Investigation Of Steel Corrosion In Lead Bismuth Eutectic (Lbe): Characterization, Species Identification, And Chemical Reactions, John Farley, Dale L. Perry, Allen L. Johnson

Transmutation Sciences Materials (TRP)

The goal of the present research is to achieve a basic understanding of corrosion of steels by Lead Bismuth Eutectic (LBE). Liquid LBE is under consideration in the transmuter as both a spallation target and as a blanket coolant. There have been previous studies of LBE, especially by the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. However, a fundamental understanding and verification of its role in the corrosion of steels is still very incomplete. We have begun a program of post-experiment testing and analysis on steel samples that have been in intimate …

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Dale L. Perry, Allen L. Johnson

Transmutation Sciences Materials (TRP)

This research program will analyze various steel samples that have been exposed to LBE as part of the national program to develop LBE and transmutation technologies. This information will be paramount in developing engineering efforts to control, avoid, and/or minimize the effect of corrosion of steels by LBE in transmuter and LBE systems. Additionally, this program provides UNLV researchers with hands-on experience that will be crucial in developing the UNLV LBE program, supporting the University’s mission with the ISTC target complex, and the future development of additional facilities to examine LBE systems.

The research group plans to test the hypothesis …

Corrosion Of Steel By Lead Bismuth Eutectic: Year 1 Annual Report, John Farley

Transmutation Sciences Materials (TRP)

The goal is to investigate the corrosion of stainless steel by lead-bismuth eutectic (LBE), which has been proposed for use as a blanket coolant and a spallation target in the transmuter.

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems, Ajit K. Roy, Brendan O'Toole, Zhiyong Wang, David W. Hatchett

Transmutation Sciences Materials (TRP)

Spallation-neutron-sources, such as those under investigation for use in accelerator-driven transmutation systems, generate neutrons through the collision of high-energy protons, or charged hydrogen atoms, with heavy metal targets such as lead. As a result, these systems also tend to deposit a significant amount of hydrogen in the materials of the transmuter target and superstructure. This can result in accelerated corrosion and changes in the properties of the exposed materials. Of particular importance is a phenomenon called hydrogen embrittlement, in which materials lose their ductility (ability to deform under stress) and become brittle (more susceptible to fracture) after reacting with hydrogen. …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Task V 4th Quarterly Report, Samir Moujaes

Transmutation Sciences Materials (TRP)

The project is moving on target with the newly realigned objective set for the Phase I. Through close communications with Dr. Li and Dr. Jinsuo Zhang from LANL a realignment of the simulation work has been recommended. The reason for that is the vendor of STAR-CD/CHEMKIN had not perfected yet the final coupling of the post processing of output for any potential surface chemistry reaction taking place on the inside pipe surface of the LBE loop. This is because the coupling of CHEMKIN and STAR-CD has been done fairly recently.

Our final effort has been to generate using an innovative …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

Many of the international efforts to develop transmutation technology, including the U.S., Russian, and European scientific communities, have determined that lead bismuth eutectic (LBE) is a potential material for use as a both a spallation target and a coolant. To exploit this potential, a more thorough understanding of the effect and rates of corrosion on steels, particularly non-Russian alloys, inside the LBE systems is required. Properly controlling the oxygen content in LBE systems has been observed to drastically reduce the corrosion of structural steels in LBE. However, the transport of oxygen and formation of corrosion products is not well understood; …

Analysis Of Plastics In The Tyre Industry Using Fourier Transform Infrared Techniques, Differential Scanning Calorimetry And Softening Point Apparatus, Ching Ching Loh

Student Works (2000-2009)

The plastics in a tyre factory were investigated. The plastics were analysed by FTlR-transmission, FTI.R-ATR, softening point apparatus as well as a Differential Scanning Calorimeter. All the plastics were detected to be polyethene based with melting point range of 107 to 125°C. It was also observed that The FTIR transmission spectrum can be different from the FTIR-ATR spectrum. The FTIR-ATR spectrum gives a higher band intensity at longer wavelengths compared to the FTIR-Transmission spectrum. Interference fringes can be present in the FTlR transmission spectrum. In addition to the above, it was also found that the melting point of plastics obtained …

Formation Of Copper Dots In Copper Decoration Technique, Swee Yong Pung

Student Works (2000-2009)

Copper ions are dissolved from highly pure copper plate into the methanol during copper decoration process. As a result, copper concentration in methanol is increased with time. The copper concentration in methanol measured by ICP-OES is correlated well with the calculated value based on the magnitude of current and time during the process. Consequently, higher magnitude of current can be applied to build up copper concentration in methanol in shorter period. When copper ions are ejected in methanol, they are positively charged. They experience force from electric field and migrate towards oxide surface. Eventually, these copper ions will be discharged …

Corrosion Of Steel In Sea-Bottom Mud Of Nothern China Sea Area, Gong-Yu Guo, Jing-Lei Zhang, Bao-Rong Hou, Fang-Ying Yang

Journal of Electrochemistry

Corrosion experiments of A₃, 16Mn, 20^# as well as ZCE36-225 steel were carriedout in southern Bohai sea and Qingdao sea areas. The sea-bottom mud in southern Bohai sea areais the sandy mud and that in Qingdao sea area is pure beach sand. In this experiment, the compareing test of two modes with electric connected and non-electric connected modes was carriedout. The experiment results showed that: 1) The corrosion rate of steel in sea-bottom mud has astrong relation with mud types. The corrosion rates of steels in pure beach sand are much higherthan those in sandy mud. 2) …

Electrosynthesis Of A New Electroactive Poly(2,2'-Diaminophenyloxydisulfide), Yu-Zhi Su, Yan-Wen Rao, Ye Yang, Mei-Bing Chen, Yin-Ling Qiu, Yong-Hua Zhang, Ke-Cheng Gong

Journal of Electrochemistry

A new electroactive poly (2,2' diaminophenyloxydisulfide) (PDAPD) was successfully synthesized from acetonitrile(AN)/tetrahydrofuran (THF) solutions containing the supporting electrolyte (LiClO₄) and the various kinds of acids (HCl, CF₃COOH, CCl₃COOH) on Pt electrode by consecutive cyclic voltammiry. The effects of the concentrations of supporting electrolyte (LiClO₄) and acid (HCl, CF₃COOH, CCl₃COOH) on electrodepositon of PDAPD film were investigated. The best experimental conditions for electrosynthesis of a highly electroactive conducting polymer film are that the concentrations are 0.1 mol/L and between 0.05 mol/L～0.5 mol/L,respectively for LiClO₄ and HCl.

Studies On The Anti-Corrosion Behavior Of Corrosion Inhibitor To The Ship Building Steel In Moist Air, Yong-Tao Zhao, Jian-Hua Wu, Jia Wang

Journal of Electrochemistry

The anti corrosion behavior of 907A steel, which were covered with thin inibitor layers in moist air, were simulated, The electrochemical measurements, including EIS method and the coulostatic method, were used to atmospheric corrosion monitor (ACM) under thin inhibitor layers to study the mechanism of rust preventiion. the results shown that the mechanism of inhibiting corrosion was different from the steel immersed in inhibitor solutin, the anodic reaction process under thin inhibitor layers had the advantage over that of cathodic for blocking the speed of corrosion. At the later stage of soaking, the blend feature due to the electrochemical process …

The Investigation Of Prepare Condition For Micropores Membranes From Poly(Vinylidene Fluoride), Xu-Mei Ren, Feng Wu, Ying Bai, Hang-Jun Li, Xue-Jie Huang

Journal of Electrochemistry

The micropores membranes from Poly (vinylidene fluoride) were prepared by the phase inversion process. The effects of the casting solution composition, exposure time prior to coagulation and temperature of the coagulation bath on properties of prepared membranes were investigated. For all prepared membranes an asymmetric structure, sometimes without a dense skin layer, was observed.

An Investigation Of Structural Properties Of Li-Al-Mixed Doped Spinels Materials Li 1+XAlYMn Z-YO4, Zi-Shan Zheng, Zi-Long Tang, Zhong-Tai Zhang, Wan-Ci Sheng

Journal of Electrochemistry

Al and Li elements were co-doped into host spinel lithium manganese oxide by a simple and economical preparation technology. There was an investigation of the influence of doped Al contents on the initial capacity and cycling performance of the materials. The investigation of the XRD patterns, the analysis of the SEM micrographs and the determination of IR spectroscopy showed that the particles of dopant materials are fine, narrowly distributed and well crystallized, and the bonds Mn-O are stronger than these of undoped materials. The resulted materials have a high initial capacity of 119 mAh/g and good cycling characterization. The capacity …

Studies On The Properties Of The Anodic Films Formed On Lead- Lanthanum And Lead-Samarium Alloys In Sulfuric Acid Solution, Hou-Tian Liu, Chun-Xuao Yang, Hai-Heng Liang, Jiong Yang, Wei-Fang Zhou

Journal of Electrochemistry

AC voltammetry, linear sweep voltammetry, and cyclic voltammetry were applied to study the anodic corrosion of Pb, Pb-1.0 at% La and Pb-1.0 at% Sm electrodes in 4.5 mol·dm^-3 H₂SO₄ solution (25 ℃). The experiment results show that samarium can inhibit the anodic corrosion of lead and decrease the impedance of anodic Pb(Ⅱ) film. Lanthanum can also decrease the impedance of the anodic Pb(Ⅱ)film, but the effect is smaller.

The Research Of Organic Electrolyte Solutions For Li-Ion Batteries, Quang-Chao Zhuang, Shan Wu, Wen-Yuan Liu, Zhao-Da Lu

Journal of Electrochemistry

The characteristics of organic electrolyte solutions and its influences on the ion conductivity are summarized. The chemistry and electrochemistry of organic electrolyte solutions and characteristics of ordinary organic solvents are introduced. Progresses in studies of organic electrolyte solutions such as electrolyte salts, organic solvents, additives in recent years are reviewed, current situation of the studies of organic electrolyte solutions were also discussed.

New Progress Of Intrinsic Conducting Polymers' Application, Wan Chen, Cheng-Hao Liang, Yang Xie

Journal of Electrochemistry

As a kind of functional polymer, the intrinsic conducting polymer has the special chemical, electrochemical and optical properties. So it has wide application such as batteries, electromagnetic wave shielding, electroluminescent etc. Recent development and the problems of the intrinsic conducting polymers' application were briefly reviewed in this paper.

Thermal Effects On The Measurement Of Photocurrent At Anodic Films On Silver Electrode, Yuan Gu, Zhi-Yu Jiang

Journal of Electrochemistry

The influence of heat on the photocurrent of Ag electrde in alkaline solution was investigated by measuring photocurrent, photothermal signal and thermal current under the irraiation of laser beams with the wavelengths of 488 nm and 532 nm. It was found the photocurrent atthe Ag₂O film was influenced by the temperature change at the electrode surface under the irradiation of light. During the electrochemical transfer between Ag, Ag₂O and AgO in the anodic filmthe surface temperature changed obviously due to the different absprptance of the surface subrstances.It was suggested by comparing the voltammograms, photocurrent curves and …

Study Of Hydrogen Diffusion Behavior In Hydrogen Storage Alloy Mlni3.75Co0.65Mn0.4Al0.2 With Potential Step Method, Xian-Xia Yuan, Nai-Xin Xu

Journal of Electrochemistry

Potential step method was employed to study the hydrogen diffusion behavior in hydrogen storage alloy MlNi_3.75 Co_0.65Mn_0.4Al_0.2 with various depth of discharge (DOD) at ambient temperature and with 50% DOD at various temperatures. It was found that hydrogen diffusion cofficient in the hydrogen storage alloy increaes with the increase in DOD at ambient temperature. and for the alloy with 50% DOD, the hydrogen diffusion coefficient increases with the increase in temperature and the activation energy for hydrogen diffusion in the alloy is 19.87 kJ/mol.

Research Progress On Proton Exchange Membranes Of Fuel Cells, Jing-Rong Yu, Dan-Min Xing, Fu-Qiang Liu, Jian-Guo Liu, Bao-Lian Yi

Journal of Electrochemistry

The proton exchange membrane fuel cells (PEMFC) use proton exchange membranes(PEM) as their electrolytes. The performance of the PEMFC is strongly dependent on the characteristics of the PEM. In this paper, the requirements of the PEM utilized in the PEMFC were analyzed. The per-fluorinated, partially fluorinated and non-fluorinated PEM were introduced respectively. The structures, preparation, properties of the various types of PEM and their applications in the PEMFC were also discussed in detail.

The Influence Of Synthesis Conditions On The Electrochemical Properties Of Spinel Limn2O4, Jun-Feng Xu, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical properties of spine LiMn₂O₄ synthesized via a solid state reaction were investigated. Electrolysis MnO₂(EMD), Li₂CO₃ ,LiOH and LiNO₃ were used as the initial materials. It was found that the electrochemical properties of LiMn₂O₄ were strongly influenced by the synthesis conditions. The LiMn₂O₄ sample sprepared via the reactionof EMD and LiNO₃ showed the best properties for a lithiumion intercalation reaction. The procedure includes two steps:pretreatment at 280 ℃ for 6 hours to initiate the permeation of melting LiNO₃ into the microporesof EMD …

Adsorption And Oxidation Of Methanol On Pt And Sb, S Modified Pt Electrodes Using Cyclic Voltammetry And Eqcm, Guo-Liang Chen, Sheng-Pei Chen, Heng Lin, Xing-Hong Zheng, Shi-Gang Sun

Journal of Electrochemistry

The processes of adsorption and oxidation of methanol on Pt, Pt/Sb ad and Pt/S ad electrodes were studied by using cyclic voltammetry and electrochemical quartz crystal microbalance (EQCM). The results demonstrated that the oxidation of methanol depends strongly on oxidation states of electrode surface. Sb adatoms on Pt surface can adsorb oxygen at relatively low potentials, and exhibit catalytic effects for methanol oxidation. In contrast to Pt electrodes, the oxidation peak potential of methanol in this case negatively shifted to about 130 mV. In a contrary, the oxidation of S_ad atoms consumes oxygen species of Pt electrode surface. As …

Study On Electrochemical Behavior Of Copper In Nh3 ·H2O Solution Medium Including K3[Fe(Cn)6] During Cmp, Yue-Hua Hu, Han-Wei He, Ke-Long Huang

Journal of Electrochemistry

Influence of medium pH value and passivator concentrations on the copper passivation and CMP process were studied by electrochemical measurement technologies, relations of the film thickness and tightness with polishing process and polishing rates were investigated. Electrochemical variables influencing polishing process and rates were found out. Electochemical mechanism of polishing processes were explained by corrosion potential and corrosion current density. A recipe of K₃[Fe(CN)₆] as passivator and nano sized γ-Al₂O₃ as abrasives in medium of NH₃·H₂O solution was confirmed reasonable. It is shown that the conditions of polishing process …