Chemistry Commons^™

Synthesis,Characteristics And Electrochemical Performance Of Nano-Sized Snco/Graphite Composites As Anode For Lithium Ion Batteries, Jin-Shu Cai, Ling Huang, Fu-Sheng Ke, Shi-Gang Sun

Journal of Electrochemistry

The nano-structural Sn-Co/graphite composites were prepared by chemical reduction of the alloy electroless deposition solution in graphite suspensions, and the composites were annealed at 500 ℃. The phase structure and surface morphology of the composites were measured by XRD, SEM and Raman. The results indicate that there were high dispersions and high loadings of Sn-Co nanoparticles on graphite by thermal treatment. Electrochemical lithium storage performance was studied preliminarily on the obtained samples. The graphite modified with the Sn-Co nanoparticles possessed a higher electrochemical reversible capacity than that of graphite during the charge and discharge process. The appetency between the Sn-Co …

Influence Of Magnesium Nitrate On The Corrosion Performance Of Sol-Gel Coated Aa2024-T3 Aluminium Alloy, Rajath Varma, Brendan Duffy, John Cassidy

Articles

Traditional anti-corrosion technology has relied heavily on using reducible metal species, predominantly hexavalent chromium (Cr(VI)), for protecting reactive metal alloys such as aluminium which is extensively used in the aerospace sector. However, the impending changes in the use of Cr(VI) in Europe and the United States have forced aerospace manufacturers to examine alternative materials for protecting aluminium. One of the most promising alternatives being investigated are organosilane based sol-gels containing anticorrosion additives. In this work the anti-corrosion properties of magnesium (II) nitrate (Mg(NO3)2) as a inhibitor was investigated at different concentrations (0.1% - 1.0 wt %) in a methyltriethoxysilane (MTEOS) …

Yttrium And Hydrogen Superstructure And Correlation Of Lattice Expansion And Proton Conductivity In The Bazr0.9y0.1o2.95 Proton Conductor, A. Braun, A. Ovalle, V. Pomjakushin, A. Cervellino, S. Erat, Wayne C. Stolte, T. Graule

Chemistry and Biochemistry Faculty Research

Bragg reflections in Y-resonant x-ray diffractograms of BaZr_0.9Y_0.1O_2.95 (BZY10) reveal that Y is organized in a superstructure. Comparison with neutron diffraction superstructure reflections in protonated/deuterated BZY10 suggests that both superstructures are linked, and that protons move in the landscape imposed by the Y. The thermal lattice expansion decreases abruptly for protonated BZY10 at T≥648±20 K, coinciding with the onset of lateral proton diffusion and suggesting a correlation of structural changes and proton conductivity. The chemical shift in the Y L₁-shell x-ray absorption spectra reveals a reduction from Y³⁺ toward Y²⁺ upon …

Observed Superspin-Glass Behavior In Ni0.5zn0.5fe2o4 Nanoparticles, Antony Adair

Open Access Theses & Dissertations

In this investigation we seek to identify the magnetic behavior of Ni0.5Zn0.5Fe2O4 nanoparticles though AC-susceptibility and DC-magnetization measurements. Powder x-ray diffraction was performed to determine the purity and average diameter ( ~ 9nm) of the particles. Aditionally, structure was confirmed by comparison through the International Centre for Diffraction Data's Powder Diffraction File [52] (PDF # 08-0234).

Zero-field cooled and field cooled DC magnetization measurements (bifurcation and blocking temperature), as well as M(H) hysteresis (below and above the blocking temperature) lead us to initially suggest that the material may in fact be superparamagnetic. However, further investigation of the real AC susceptibility …

Computational Modeling Studies Of The Structures And Properties Of Organotin(Iv) And Stannyl-Thioether Systems With Comparisons To X-Ray Crystallography, Michelle R. Stem Joseph

Open Access Theses & Dissertations

Controlling the toxic effects of organotin(IV) compounds involves engineering the structure of the molecules to optimize their properties. Molecular engineering, coupled with improved capabilities to generate reliable computational optimization models (COMs), will enable researchers to have greater success at harnessing the highly specific cytotoxicity of organotins. For example, as the thio_n ligand phenyl groups were replaced with Cl atoms, the S-Sn intramolecularity was strengthened, the bond distance decreased, and the stannyl tetrahedral structure was deformed from its triphenyl conformation. With each substitution, conformation deformations lowered the damaging bioactivity levels of thio_n. Bonding various ligands to organotin(IV) compounds …

Study Of Corrosion Of Materials In The Sulfur-Iodine Hydrogen Production Cycle, Thao Trung Ho

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hydrogen is of great interest since the availability of traditional fossil fuels is in decline. Strictly speaking, hydrogen is not a primary source of energy but is an energy carrier, since energy typically must be used from another source (electricity, natural gas, coal, etc.) to produce it. Of hydrogen production techniques, the Sulfur-Iodine thermochemical water splitting process (S-I cycle), which was proposed by General Atomics (GA), is promising with its simplicity and high efficiency. Most of the chemicals are recycled except water. However, the S-I cycle operates in a harsh, corrosive environment in the presence of a mixture of iodine …

Spectroscopic Investigation Of Palladium-Copper Bimetallic Systems For Pem Fuel Cell Catalysts, Timo Hofmann

UNLV Theses, Dissertations, Professional Papers, and Capstones

One of the main barriers to commercialization of polymer electrolyte membrane fuel cells systems is cost, which is largely due to the need of platinum (Pt)-containing catalysts. In this thesis we investigate bimetallic systems consisting of a base metal (copper) and a noble metal (palladium) that, as an alloy on the nanoscale, mimic the electronic properties that make Pt desirable as a catalyst.

We present a detailed investigation of the electronic structure of carbon-supported Pd/Cu nanoparticle catalysts, model bilayer thin film systems, alloys, and various metal reference samples. We have investigated the valence band structure of the catalysts using a …

Nondestructive Evaluation Of Aircraft Composites Using Terahertz Time Domain Spectroscopy, Christopher D. Stoik

Theses and Dissertations

Terahertz (THz) time domain spectroscopy (TDS) was assessed as a nondestructive evaluation technique for aircraft composites. Material properties of glass fiber composite were measured using both transmission and reflection configuration. The interaction of THz with a glass fiber composite was then analyzed, including the effects of scattering, absorption, and the index of refraction, as well as effective medium approximations. THz TDS, in both transmission and reflection configuration, was used to study composite damage, including voids, delaminations, mechanical damage, and heat damage. Measurement of the material properties on samples with localized heat damage showed that burning did not change the refractive …

Studies Of Surface Diffusion In Pemfc Electrodes, Jiang-Shui Luo, Jian Chen, Bao-Lian Yi, Chuan-Sin Cha, Hua-Min Zhang

Journal of Electrochemistry

A PEMFC electrode consisting of dual-layer catalyst layer(CL) was fabricated in this work. The outer CL was Nafion-free,while the inner CL was Nafion-bonded. The effects of Pt/C catalyst in the outer CL that did not contact with Nafion on the current generation in PEMFC electrodes were investigated. Cyclic voltammetric studies indicated that the Pt/C catalyst in the outer CL without direct contact with Nafion was still electrochemically active in taking part in the adsorption/desorption of hydrogen and the electrochemical oxidation/reduction of the oxygen-containing species occurring at the interface of "Pt/Nafion" in the inner CL. The polarization curves showed that the …

Ec-Pt/Cnts Glucose Oxidative Electrode, Jia-Hua Liang, Chun-Mei Zhou, Hong-Juan Wang

Journal of Electrochemistry

A glucose oxidative electrode(GOD),EC-Pt/CNTs glucose oxidative electrode,was constructed by ethyl cellulose(EC) and Pt/CNTs.The sensitivity of the EC-Pt/CNTs GOD is 0.85 μA/mM in the concentration range of 0～4 mmol/L of glucose.After dipped in PBS(4℃) for 18 days,the activity of the EC-Pt/CNTs GOD can reach 80%.It is promising for the EC-Pt/CNTs GOD to be used to construct glucose biosensor.

Corrosion Inhibition Of Magnesium Alloy In 3.5% Nacl Medium By Tungstate, Ling-Jie Li, Zhi-Ming Yao, Jing-Lei Lei, Dong-Hai He, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS),Tafel polarization curves and scanning electron microscopy(SEM) were used to study the corrosion inhibition of AZ61 magnesium alloy in 3.5% NaCl medium with tungstate.Results showed that tungstate demonstrates strong inhibition to the corrosion of AZ61 magnesium alloy.At the concentration of 0.01 mol/L,tungstate has a high inhibition efficiency 75.5%.Tungstate is an anodic inhibitor that mainly inhibited the anodic reactions of magnesium alloy through forming a compact protective layer that covered the magnesium alloy surface active sites.

Behavior Of Copper Electrodeposition In Copper Electroplating Solution With Different Peg Molecular Weight, Lie Yin, Zeng-Lin Wang

Journal of Electrochemistry

The effect of the polyethylene glycol(PEG) molecular weight(MW) upon via-hole filling with diameter of 50 μm and aspect ratio of 1 in the acid copper plating solution was studied.The cathodic polarization in copper electroplating bath with PEG of different molecule weights was investigated by linear sweep voltammetry.The surface roughness,crystallography,and the resistivity of copper films were characterized by X-ray diffraction(XRD),atomic force microscopy(AFM) and the four-point probe measurements.The results showed that the polarization on the cathode and the hole-filling capability of electroplating copper bath were increased evidently with an increase of PEG molecular weight from 600 to 8000.When the PEG MW was …

Voltammetric Determination Of Iodate Ion In Table Salt By Carboxylic Carbon Nanotubes Modified Carbon Paste Electrode, Jun-Hua Li, Fu-Xing Zhang, Jian-Qiu Wang, Zhi-Feng Xu, Rong-Ying Zeng, Yan Yu

Journal of Electrochemistry

A highly-sensitive and mercury-free method of determining iodate ion in table salt was established based on carboxylic carbon nanotubes modified carbon paste electrode.In 0.1 mol/L NaOH solution,there was a sensitive cathodic stripping peak on voltammograms.The stripping peak potential was-0.52 V when accumulation time of IO-3 at the modified electrode was 60 s and the potential scan rate was 300 mV/s.There was a good liner relationship between the peak current and IO-3 concentration in the range of 8.0×10^-10 ～ 5.0×10^-8 mol/L and 1.0×10^-7 ～ 3.0×10^-6 mol/L with the correlation coefficient of 0.999 and 0.998,respectively.The detection limit was …

The Hydrothemal Synthesis Of Nanoscale Lifepo4 And Its Electrochemical Performance, Si-Min Wang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The cathode materials of LiFePO₄ were prepared via a hydrothermal reduction method using FeCl₃ as Fe source and iron as a reducing agent.The results showed that ferric salt could be reduced to ferrous salt completely under the hydrothermal condition and pure-phase LiFePO₄ was obtained based on the test results of XRD and FTIR. Carbon-coated LiFePO₄ was synthesized by pyrolysisng glucose at high temperature. The morphologies of pure LiFePO₄ displayed cluster-like while the LiFePO₄/C displayed sphere-like particles. The electrochemical test showed that the LiFePO₄/C had good rate performance,while LiFePO₄ delivered much …

Synthesis Of The Lifepo4 By Co Reduction: Reaction Mechanism And Kinetics, Yun-Hua Chen, Yong Yang

Journal of Electrochemistry

LiFePO₄ cathode material was synthesized by CO reducing FePO₄ and LiOH precursors.The structure,morphology and electrochemical performances of such LiFePO₄ material were characterized by XRD,SEM and charge-discharge tests.It was shown that the particle size of the LiFePO₄ synthesized with 5% excess of LiOH in the precursor was about 200 nm.By carbon coating,the LiFePO₄ electrode was able to deliver a reversible capacity of 158 mAh·g^-1 at 0.1C discharge rate.Temperature-programmed X-ray diffraction was employed to monitor the reaction during the formation of LiFePO₄,and Li₃Fe₂(PO₄)₃ was found to be …

Primary Study Of Tiron As Active Materials For The Redox Flow Battery, Yan Xu, Yue-Hua Wen, Jie Cheng, Yu-Sheng Yang, Zi-Li Xie

Journal of Electrochemistry

Effects of solution pH on the electrochemical behavior of tiron(sodium 4,5-dihydroxy-1,3-benzendisulfonic) couple(on a graphite electrode) were studied by cyclic voltammetry in aqueous solutions.It is shown that at pH<4,tiron exhibited a redox process at a relatively high potential with a good reversibility.A redox flow battery was formed employing tiron as the positive active species and V(III)/V(II) as the negative redox couple.In sulfuric acid medium,the coulombic efficiency of the tiron-V redox flow cell was more than 90% with a good cycle life.The decay in the cycle performance was minimal.Therefore,the feasibility of tiron as active materials for redox flow battery application is demonstrated.

Study On The Texturization Of C-Si Wafers By Different Kinds Of Alkaline For Heterojunction Solar Cells, Yu-Hua Dou, Yu-Qin Zhou, Mei-Fang Zhu, Shuang Song, Feng-Zhen Liu, Jin-Long Liu, Zhan-Jun Zhang

Journal of Electrochemistry

The texturization of(100) crystalline silicon(c-Si) wafer was studied by field-emission scanning electron microscope using different kinds of etchant: sodium hydroxide,sodium carbonate and tribasic sodium phosphate.By optimizing the etching parameters,the lowest values of averaged reflectance(Rav) were obtained to be 9.70% for NaOH,9.76% for Na₂CO₃ and 8.63% for Na₃PO₄·12H₂O,which is comparable to that of the wafer with textured surface covered with an anti-reflection coating of either silicon nitride or thermally grown silicon dioxide.The relation of Rav and surface morphology of textured wafer was analyzed.Moreover,special emphasis was put on the role of isopropyl alcohol(IPA) …

Combustion Product Characterization Of The Iron-Heated Powders In Thermal Batteries, Jin Chong, Xue-Ping Gao, Ji-Qiang Wang

Journal of Electrochemistry

The combustion products of thermal battery used iron-heated powders have been studied.It is identified by X-ray diffraction (XRD) analysis that the main compositions of the combustion products are Fe, FeO and KCl. The transmission electron microscopy(TEM) shows a typical core-shell structure with un-reacted Fe particle core coated by FeO shell with a shell thickness of around 200 nm. The combusted iron-heated powders exhibit no metal property, which is contrast to previous assumption. Further measurement indicates that at the ambient temperature the combustion products show semiconductor property of the p-type with conductivity in the order of 103 S·cm^-1, which …

Preparation And Electrocatalystic Performance Of Ir/C Catalyst For Ammonia Oxidation, Qing-Mei Kong, Yi-Ping Han, Ling-Juan Deng, Tian-Hong Lu, Ya-Wen Tang

Journal of Electrochemistry

The Ir/C catalyst with 30%(by mass) Ir was prepared in the CH₃CH₂OH and H₂O binary system.The X-ray diffraction(XRD) data showed that the average sizes of the Ir particles in the Ir/C catalyst was about 2.2 nm.The results of the electrochemical measurements indicated that the electrocatalytic activity of the Ir/C catalyst for the ammonia oxidation in the neutral NaClO₄ solution was similar to the Ir catalyst,while electrocatalytic stability was much better than that of the Ir catalyst.Furthermore,the peak current density of the ammonia oxidation at the Ir/C catalyst electrode showed a good linear relationship …

Direct Electrochemistry Of Chloroperoxidase At Gc Electrode Modified With Swnts, Hong-Xia Zhang, Xia-Qin Wu, Wen-Jing Hou, Wen Xie, Zhong-Qing Lu, Rong Wang, He-Xing Li

Journal of Electrochemistry

The chloroperoxidase(CPO) was immobilized onto the surface of SWNTs modified electrodes.The electrochemical behaviors of modified electrode have been investigated by cyclic voltammetry.The appearance of a pair of well-defined redox peaks in the CV curve indicated that SWNTs can promote the electron transfer reaction of CPO.The results of cyclic voltammetry in PBS of different pH,from 3~9,showed that the reaction of CPO on the modified electrode was with equal numbers of electron and protein.This readily prepared SWNTs modified electrode showed excellent stability and good catalysis to O₂.

Preparation And Optical Transmission Of The Zno Nanorod Array Films, Feng Ye, Jing-Jing Li, Tong-Tao Wang, Yong-Liang Wang, Yun Liu, Xin-Dong Wang

Journal of Electrochemistry

By using a galvaostatic electrodeposition method in the ZnCl₂ solution,the highly oriented ZnO nanorod array films have been successfully prepared on ITO substrate after the pretreatment with ZnO nanoparticles.And they were characterized by scanning electron microscope,X-ray diffraction and transmittance spectra.The results indicated that the ZnO nanorod arrays grew along(001) direction with an orientation perpendicular to the substrate.When the wavelength of incident was over 380 nm,the ZnO nanorod arrays showed high optical transmission of above 95%.Furthermore,the band gap became narrower.

Preparations Of Composite Electrodes Of Pt With HXWo3 And Catalytic Activity Toward Oxygen Reduction Reaction, Pan-Pan Guo, You-Ju Huang, Hong-Yan Yang, Wei Li, Qing-Long Zhang, Wei-Shan Li

Journal of Electrochemistry

Three composite electrodes of platinum with hydrogen tungsten bronze(H_xWO₃)were prepared by voltammetry: hydrogen tungsten bronze deposited on platinum(H_xWO₃/Pt);platinum deposited on hydrogen tungsten bronze(Pt/H_xWO₃) and codeposited platinum and hydrogen tungsten bronze(Pt-H_xWO₃).The eletro-catalytic activities of three electrodes toward oxygen reduction reaction were studied.It is found that the catalytic activity of platinum can be improved by introducing with hydrogen tungsten bronze.Among these composite electrodes Pt/H_xWO₃,and the electrode shows the best eletro-catalytic activity toward oxygen reduction reaction,hence,provides a new way for reducing loading of …

High Performance Fuel Cell Catalyst And 5kw Pemfc Stack Without Humidification At Room Temperature And Atmosphere, Xin-Fa Hu, Min Chen, Shi-Jun Liao

Journal of Electrochemistry

The Pt/C catalyst with high dispersion and high performance was prepared successfully by an organic colloidal method and small batch production(10g) of Pt/C catalyst has been realized.The particle sizes of the active components in the catalyst could be as small as 2.8 nm and the active surface area was up to 450 m²/g.A high performance membrane-electrode assembly(MEA) with surface area of 275 cm² has been prepared by using the home-made catalyst with a catalyst coated membrane method invented in the lab,and a 5 kW stack has been assembled.The stack showed working 10 h at room temperature,atmosphere and …

Ceo2/Pt Composite Electrodes And Their Catalytic Performance, Ying Fu, Zi-Dong Wei, Yong-Chao Feng, Xin-Li Ma, Ming-Jia Liao, Chao Liao, Jie Zhang, Huan Zhang

Journal of Electrochemistry

In this paper,the cerium oxide(CeO₂) nanoparticles were electrochemically deposited on a Pt electrode by potentiostatic deposition(psd) and potential pulse deposition(ppd) to form CeO₂/Pt composite electrodes,CeO₂/Pt(psd) and CeO₂/Pt(ppd).The properties of the CeO₂ were characterized by field emission scanning electron microscope(FESEM) and X-ray diffraction(XRD).The results showed that the CeO₂ nanoparticles prepared by psd and ppd were homogeneous and dense.The methanol oxidation reaction(MOR) and oxygen reduction reaction(ORR) on the Pt electrode were enhanced with the introduction of CeO₂ into Pt.In addition,the catalytic capability of the CeO₂/Pt electrode can be further …

Electrochemical Behavior And Determination Of Paracetamol On Activated Glassy Carbon Electrode, Bao-Yu Tan, Fang Liao, Xiao-Ying He, Qing-Tao Zhu, Jun Hua, Xiao-Li Jiang

Journal of Electrochemistry

The electrochemical behavior of paracetamol(PCT) was studied at glassy carbon electrode activated by cyclic voltammetry.In HAc-NaAc buffer solution(pH=4.00),a couple of sensitive redox peaks were recorded about 0.54 V in the cyclic voltammograms.The result indicated that the process was controlled by adsorption and nearly reversible.The reaction electron and proton numbers were estimated,respectively,to be two.Excllent linearity was observed in the correlation between the oxidation peak current and the concentration of PCT in the range of 8.00×10^-6～2.00×10^-4 mol·L-1.The correlative coefficient was-0.999 18.The detection limit was 6.34×10^-6 mol·L^-1.This method can be used for the determination of PCT real …

Fabrication Of Superhydrophilic Aluminum Oxide Through Single-Step Anodic Oxidation, Qin Zhang, Qi-Ming Yin, Jia-Ming Ye, Yuan-Rong Zhu

Journal of Electrochemistry

Hydrophilic aluminum oxide is popularly used for heat exchanger of air-condition.Herein,we developed a simple method to prepare superhydrophilic aluminum oxide on the surface of aluminum through single-step electrochemical oxidization.The morphologies and water contact angles on surfaces of alumina fabricated under different electrochemical conditions were investgated.Superhydrophilic surfaces fabricated by this method have good stability and high mechanical strength with water contact angle almost 0°.Coated with low surface energy materials,superhydrophilc alumina will be converted to superhydrophobic.

Voltammetric Determination Of L-Cysteine At Bipyrine Bridged Copper(Ⅱ) Complex Modified Glassy Carbon Electrode, Ming-Yan Wang, Fan Yang, Sheng-Yu Zhang, Xing-You Xu, Xu-Jie Yang

Journal of Electrochemistry

A modified electrode has been constructed by depositing a novel copper(Ⅱ) complex 2biPy(ClO₄)₄ on the glassy carbon electrode through the method of cyclic voltammetry(CV).It was found that the modified electrode exhibited high electrocatalytic activity toward L-Cysteine oxidation with good reproducibility and high sensitivity.The peak current of semi-derivative linear scan was proportional to the concentration of L-cys in the range of 1×10^-6～3×10^-4 mol·L^-1.The detection limit was 5×10^-7 mol·L^-1.

Environmental Effects On Corrosion Properties Of Alloy 22, Mano Misra

Publications (YM)

This document presents detailed technical report for four Subtasks that were conducted independently. All four Subtasks investigated environmental effects on corrosion properties of Alloy 22. The four Subtasks that were investigated are as follows: Subtask 1: Experimental Determination of Parameters for the General Corrosion Model. Subtask 2: Corrosion under Dust Deposits Containing Hygroscopic Salts. Subtask 3: Heated Electrode Approach for the Study of Corrosion Under Aggressive Conditions. Subtask 4: Effect of Hydrogen Permeation on the Stability of the Passive Film of Alloy 22.

Electrochemical Reductive Behaviors Of 3,4,5,6-Tetrachloro-2-Trichloromethylpyridine At Ag Electrode, Chun-An Ma, Yi-Jiao Hu, Ying-Hua Xu

Journal of Electrochemistry

The electrochemical reductive behavior of 3,4,5,6-tetrachloro-2-trichloropyridine(heptachloropyridine) on silver electrode in the mixture of acetonitrile and water solutions containing TBAP was investigated by cyclic voltammetry.The influences of scan rate,concentration and temperature on the electrochemical behavior were discussed.It was shown that the reduction of heptachloropyridine on the silver electrode was a diffusion-controlled irreversible process.The diffusion coefficient of heptachloropyridine in the acetonitrile solution was 3.0×10^-5 cm²/s.The mechanism of the dechloration of 3,4,5,6-tetrachloro-2-trichloropyridine was also discussed.

Electrochemical Synthesis, Characterization And Fluorescence Property Of Nano Na2Sif6, Guo-Xu Qin, Xin-Jun Wan, Xi-Mei Yuan, Dao-Bao Chu

Journal of Electrochemistry

The nano TiO₂ film was prepared by sol-gel process and characterized with X-ray diffraction(XRD) and scanning electron microscope(SEM).It was found that the average size of pore diameter was about 80 nm for the nano TiO₂ film.The Nano Na₂SiF₆ was synthesized by electrochemical deposition on the nanoporous film electrode and characterized with XRD and transmission electron microscope(TEM).The result showed that the average size of nanoparticle was 20 nm for the nano Na₂SiF₆.The fluorescence property of nano Na₂SiF₆ was also studied briefly.The result indicated that the nano Na₂SiF …