Chemistry Commons^™

Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng

Journal of Electrochemistry

The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …

Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang

Journal of Electrochemistry

The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm² in Fe(Ⅲ)-oxalate-calcium gluconate system.

Electrochemical Behaviors Of Hydroquinone On Polypyrrole/Stab-Nammt/Gc Electrode, Rong Li, Jian Xiong, Wei-Qiong Zhu, Yuan-Yuan Han, Jin Xu, Xiao-Ying He

Journal of Electrochemistry

The PPy/STAB-MMT/GC electrode was made using montmorillonite modified by STAB and polypyrrole (PPy). The electrochemical behaviors of hydroquinone on the PPy/STAB-MMT/GC electrode were researched by cyclic voltammetry and square wave stripping voltammetry (SWSV). The results showed that the electrode reaction occurred on the hydroquinone electrode was controlled by diffusion in PBS (pH=6.0). The number of electron transfer was equal to the number of protons (n=m=1) with the effective area of PPy/STAB-MMT/GC electrode Aeff=0.031 cm². Under the optimized conditions, the linear response of peak current in SWSV with the concentration of hydroquinone in a range of 8.0×10^-6~8.0×10 …

Fabrication Of Size-Tunable Metallic Nanoparticles Using Plasmid Dna As A Biomolecular Reactor, Jacopo Samson, Irene Piscopo, Alex Yampolski, Patrick Nahirney, Andrea Parpas, Amit Aggarwal, Raihan Saleh, Charles Michael Drain

Publications and Research

Plasmid DNA can be used as a template to yield gold, palladium, silver, and chromium nanoparticles of different sizes based on variations in incubation time at 70 °C with gold phosphine complexes, with the acetates of silver or palladium, or chromium acetylacetonate. The employment of mild synthetic conditions, minimal procedural steps, and aqueous solvents makes this method environmentally greener and ensures general feasibility. The use of plasmids exploits the capabilities of the biotechnology industry as a source of nanoreactor materials.

A Modified Surface On Titanium Deposited By A Blasting Process, Caroline O' Sullivan, Peter O'Hare, Greg Byrne, Liam O'Neill, Katie B. Ryan, Abina M. Crean

Publications

Abstract

: Hydroxyapatite (HA) coating of hard tissue implants is widely employed for its biocompatible and osteoconductive properties as well as its improved mechanical properties. Plasma technology is the principal deposition process for coating HA on bioactive metals for this application. However, thermal decomposition of HA can occur during the plasma deposition process, resulting in coating variability in terms of purity, uniformity and crystallinity, which can lead to implant failure caused by aseptic loosening. In this study, CoBlast™, a novel blasting process has been used to successfully modify a titanium (V) substrate with a HA treatment using a dopant/abrasive regime. …

Study On Residual Powders Of Lithium-Ion Batteries With Different Voltages After Explosion, He Li, Zhi-Kui Chen, Ji-Na Cao, Guang-Chuan Liang

Journal of Electrochemistry

The residual powders of lithium-ion batteries at different voltages after explosion were obtained by using the battery impact testing machine. And these powders have been investigated by weighing, water solution and X-ray diffraction (XRD). The results showed that the integrity status of copper current collector and weight of residual powders decreased gradually with increasing of battery voltage, rising of burning temperature and releasing of burning duration time. The residual powders could be separated to insoluble powders and soluble powders by the water solution. The proportion of the insoluble powders is more (about 90%) including C, Co and CoO, while the …

Surface Diffusion Of Adsorptive Species On Gold Nanoelectrodes, Bao-Fa Su, Wei Wang, Dong-Ping Zhan, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Gold nanoelectrodes were prepared successfully by a programmed laser puller. The Faraday adsorptions of oxygen and iodine, and the underpotential deposition of lead on the gold nanoelectrodes were investigated. The results showed that the active areas of nanoelectrodes were dramatically higher than their appearant geometry areas, which is caused by the surface diffusion of adsorptive species from the nanoscale gold/electrolyte interface to the adjacent gold surface.

Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries, Xiao-Jing Liu, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The tin dioxide/carbon xerogel composites were synthesized by using vacuum infiltration method. Structural characterization and morphology of the composites were investigated by using XRD, TEM and SEM techniques. BET test was performed to determine the pore size distributions of carbon xerogels and the composites. The results showed that the nano-sized SnO₂ particles (5~10 nm) were encapsulated in the pores of carbon xerogels. During the electrochemical tests the SnO₂ in the composites exhibited capacity retention of 61.9% after 100 cycles of charge-discharge tests at 100 mA/g.

Study On The Fluorescent Carbon Nanodots With Electrochemical Methods, Bao-Ping Qi, Yan-Min Long, Lei Bao, Cui Liu, Zhi-Ling Zhang, Dai-Wen Pang

Journal of Electrochemistry

Carbon nanodots are a new class of fluorescent nanoparticles with a carbon-based core, which possess wavelength-tunable luminescence, high photostability, resistance to photobleaching, water-solubility, and ease of bioconjugation. Owing to their attractive merits, carbon nanodots like other carbon nanomaterials such as fullerene, carbon nanotubes and graphene, have attracted much attention. In addition, carbon nanodots can be inexpensively produced by electrochemical methods with simple post-processing under mild conditions. Electrochemical approaches have unique advantages in the analysis of surface structures and luminescence mechanism of materials. In this review, recent advances in electrochemical methods used for the synthesis and luminescence mechanism of fluorescent carbon …

Study On The Electrochemical Behaviors Of Gc Electrode Modified With Carbon Nanotube-Polyelectrolytes And Its Application For Rutin Detection, Liang Hua, Xia-Qin Wu, Rong Wang

Journal of Electrochemistry

The electrochemical behaviors of rutin and ascorbic acid at single-wall carbon nanotube and polyelectrolytes (dimethyl-diallylammonium chloride, PDDA) film modified glassy carbon electrode was investigated. The cyclic voltammetric results showed that electron transfer of rutin at PDDA/SWCNTs/GC modified electrode is an adsorption-controlled process. The separation of oxidation peak potentials of rutin and ascorbic acid was more than 200 mV. The rutin concentration in the presence of AA were detected by differential pulse voltammetry (DPV). The experimental results indicated that the PDDA/SWCNTs/GC modified electrode can be used for the detection of rutin in the presence of high concentration of AA. The DPV …

Brief Introduction To Metal Corrosion And Protection, Hou-Yi Ma, Cong-Ying Cui, Ting Chen

Journal of Electrochemistry

This paper explains why corrosion processes are usually electrochemical in nature, describes the significance of electrochemical kinetic parameters of corrosion process, and briefly introduces the principles of corrosion protection, the most common corrosion protection methods and some special application of corrosion processes.

Effects Of Graphene On Electrochemical Behaviors Of Ni(Oh)2 As Supercapacitor Material, Zhen-Zhen Zhao, Wen-Bin Ni, Neng-Yue Gao, Hong-Bo Wang, Jian-Wei Zhao

Journal of Electrochemistry

The enhanced electrochemical properties of Ni(OH)₂ by the oxidation defected graphene were studied by both experimental method and theoretical calculation. The composite material of nano-Ni(OH)₂/graphene was prepared by potentiostatic deposition on the graphene substrate. Observed by TEM, the Ni(OH)₂ nanoparticles were well dispersed on the graphene substrate with the diameter of 5.0±0.5 nm. The capacitance of the system measured by the electrochemical test was 1928 F·g^-1. As indicated by the theoretical calculations, the composite material becomes conductive since Ni(OH)₂ is combined with surface functional groups of the graphene through the strong chemical interaction. …

Synthesis Of Limnpo4/C Used As Cathode Material For Lithium Ion Batteries, Xin Yang, Xue-Wu Liu, Gui-Chang Liu, Zhi-Cong Shi, Xin Li, Guo-Hua Chen

Journal of Electrochemistry

The LiMnPO₄/C composites were prepared using a solid-state reaction with addition of the resorcinol formaldehyde resin as the carbon source. The effects of reaction temperature and time on the crystal structure, morphology and electrochemical properties of the LiMnPO₄/C composites were investigated. The results show that the best performance was achieved with the LiMnPO₄/C composites synthesized at 600 ^oC for 12 h which had the particle sizes about 100~200 nm. The initial discharge capacities were 121.6 mAh·g^-1 at 0.02C, 110 mAh·g^-1 at 0.1C and more than 60 mAh·g^-1 at 1C. An …

Photogenerated Cathodic Protection Of Stainless Steel, Cheng-Gang Lin, Ze-Quan Lin, Jing Li, Chang-Jian Lin

Journal of Electrochemistry

A highly ordered Co-doped TiO₂ nanotube layers were fabricated by potentiostatic anodization of pure titanium in fluorinated electrolyte solutions followed by ion-exchange method. The structure and composition of the as-prepared Co-doped TiO₂ nanotube layers were characterized by SEM, XRD, UV-Vis, and XPS. The effects of dopant content on the morphologies, structural and photochemical properties of the TiO₂ nanotube arrays were investigated. The performances of photogenerated cathodic protection and the photoelectrochemical response for the Co-doped TiO₂ nanotube arrays under illumination and dark conditions were evaluated through the electrochemical measurements. The Co-doped TiO₂ nanotubes showed a stronger …

Synthesis And Electrochemical Behaviors Of Li2Coxmn1-XSio4 As A Cathode Material For Lithium-Ion Batteries, Lin Wang, Dong-Ping Lv, Yong Yang

Journal of Electrochemistry

We have successfully synthesized Li₂Co_xMn_1-xSiO₄/C (x=0, 0.1, 0.3, 0.5, 1)/C composites using hydrothermal assisted sol-gel process and ball-milling method. The results of X-ray diffraction show that the solid solutions of Li₂Co_xMn_1-xSiO₄ can be achieved when x≤0.3. The initial capacities increase from 70 mAh·g^-1 of Li₂MnSiO₄/C to 105 mAh·g^-1 of Li₂Co_0.3Mn_0.7SiO₄/C. Cyclic Voltammetry (CV) curves show that the replacement of Mn with Co can reduce the electrochemical polarization, making the insertion-extraction reaction …

Corrosion Characteristics Of Galvanized Flat Steel For Power Grounding In Nacl Solution Medium, Yong Li, Gao-Lin Wu, Bang-Fei Deng, Ping Yang, Xue-Ming Li, Qing-Bin Zong

Journal of Electrochemistry

The corrosion behavior of power grounding galvanized flat steel was studied by polarization measurement, electrochemical impedance spectroscopy and neutral salt spray test in 5% NaCl solutions. The surface morphologies of galvanized coating and structural properties of corrosion products were observed with scanning electron microscope and X-ray diffraction spectrometer, respectively. Results showed that under the temperatures of 20~60℃, the corrosion currents of galvanized flat steel increased with the temperature rising. The corrosion rate at 60℃ was 0.8408 mA·cm^-2, which is 2.9 times larger than that at 20℃. The corrosion rate dropped after reaching the maximal value of 1.95 mg·cm …

Simultaneous Determination Of Dopamine(Da)And Epinephrine (Ep) At Ca/Gc Electrode, Wang Ren, Ying Zhang, Min-Jiao Li

Journal of Electrochemistry

The citric acid modified glassy carbon electrode (CA/GC) was prepared by potentiostatic technique and was used for detections of dopamine (DA), epinephrine (EP), and their mixtures by differential pulse voltammetry (DPV). The modified electrode shows the enhanced sensitivity and excellent electrochemical discrimination to DA and EP. The cathodic potential difference between DA and EP was about 380 mV, while no cathodic reduction of ascorbic acid (AA) was observed because the oxidation of AA is an irreversible reaction at the sensor. As a result, DA and EP could be determined simultaneously with the interferences of high concentrations of AA being eliminated. …

Effect Of Au Content On Microstructural Evolution Of Snagcu Solder Joints That Undergo Isothermal Aging And Reliability Testing, Patrick J. Hyland

Master's Theses

Electronics, especially, printed circuit boards (PCBs) are a widespread technology. Metal coatings or “surface finishes” are often added to PCB board pads and component leads during manufacturing to improve their performance. Electroplated nickel/gold over copper is a popular surface finish for printed circuit boards and component leads. The presence of gold in solder joints, however, is known to have detrimental effects referred to as gold embrittlement. It is generally understood that tin-lead solder joints with less than 3 weight percent (wt%) of gold will not experience reliability issues. The acceptable level of gold in lead-free solder joints, however, is less …

53rd Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 53rd annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-endorsed by the Colorado Section of the American Chemical Society and the Society for Applied Spectroscopy. Held in Snowmass, Colorado, July 24-28, 2011.

The Effects Of Cure Schedule On Properties Of Glass-Fiber Reinforced Epoxy Matrix Composites, Trevor J. Lee

Materials Engineering

Two different two-component resin systems were cured, via Differential Scanning Calorimetry, for the times recommended by their respective manufacturers. The resin cure schedules were designed to simulate typical and attainable processing conditions; they were cured at 120°F, 140°F, and 160°F, and in-mold post-cured at 200°F, 230°F, and 260°F. The resulting scans were then compared to a baseline cure for each resin system, consisting of two heating-cooling cycles at a constant rate of temperature change. These baseline cures were then used to determine the percent cure of each sample and the shift in glass transition temperature between the baseline cure and …

Artificial Muscle Project: Process Development Of Polydimethyl Siloxane Thin Films For Use In Dielectric Electroactive Polymer Artificial Muscle Actuators, Vincent J. Gayotin, Richard W. Morrison, Paul A. Preisser

Materials Engineering

An artificial muscle design was created founded on the principles of a dielectric electroactive polymer (DEAP), which is fundamentally similar to a capacitor. A polydimethyl siloxane (PDMS)-based elastomer, Sylgard 184 from Dow Corning, was chosen for the design and spun coat onto polystyrene (PS) Petri dishes at varying speeds to create a thin film, using speeds of 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm, and 6000 rpm. The film thicknesses were measured optically through use of a microscope with coupled computer imaging software to generate a characteristic curve of film thickness to spin speed, achieving a minimum film thickness …

Effect Of Pore Size On Pseudo-Capacitive Performance Of Nio In The Mixed Electrolyte Of Koh And Hexacyanoferrate, Wen Wu, Meng-Yan Hou, Dan-Dan Zhou, Yong-Yao Xia

Journal of Electrochemistry

In this paper, five kinds of NiO samples with different pore size distributions were synthesized .The electrochemical capacitance of the samples were characterized in 3 mol/L KOH solution with and without hexacyanoferrate addition. Electrochemical test results indicated the NiO sample with an optimum pore size of about 15 nm shows high Coulombic efficiency of the N₄(NiO) electrode as the redox reaction of hexacyanoferrate ions would be limited in the pore, thus prevent ion diffusion into the bulk electrolyte solution .

Investigation Of Supercapacitors Based On Polyvinyl Alcohol Hydrogel-Polymer Electrolyte, Kai-Qing Xu, Le-Qing Fan, Ji-Huai Wu, Qing Leng, Xin Zhong, Jian-Ming Lin, Miao-Liang Huang, Zhang Lan

Journal of Electrochemistry

For the first time, the supercapacitor based on the hydrogel-polymer electrolyte which consisted of the cross-linking of polyvinyl alcohol-glutaraldehyde (PVA-GA) using 2-acrylamido-2-methyl propane sulfonic acid (AMPS) as solicitation reagent was assembled. The gel polymer electrolyte was characterized by FTIR and AC impedance. The maximum ionic conductivity is 1.23 mS/cm at room temperature. The electrochemical properties of the supercapacitor were investigated by cyclic voltammetry, AC impedance spectra and constant current charge-discharge curve. The results show that the specific capacitance reachs 139 F/g with AMPS of 1.0 g and 0.05 mL of 5 %(by mass) GA. And the specific capacitance still retained …

Electric Vehicles And Power Batteries, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

In retrospect of the historical development of Electric Vehicles (EV), the impact of battery technologies on the progress of EV was discussed. In consequence, it is concluded that the lack of advanced batteries was the main cause for the fluctuations of EV development and the sluggish commercialization of electric cars in the past century. After a brief introduction to the classification and the requirements of electric vehicles, the main issues of the batteries including safety, temperature range for operation and the cost as well as the effects of these factors on the applications of advanced batteries for electric vehicles were …

Preparation And Performance Of Carbon-Coated Si/C Composites, Li-Li Du, Quan-Chao Zhuang, Tao Wei, Yong-Li Cui, Zhi Sun, Shi-Gang Sun

Journal of Electrochemistry

Si/C composite for lithium ion batteries was obtained by pyrolyzing and ball-milling. The microstructure and component of the composite was characterized by SEM and XRD, the electrochemical performance was investigated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvano static charge-discharge tests. The results illustrate that the particle of Si/C composite prepared by pyrolysis exhibits inerratic morphology, uniform carbon-coating layer, good electrical conductivity, low resistance. The first intercalated-lithium capacity of the composite material is 4495 mAh/g; the first coulomb efficiency is 65.3%. From the second week the coulomb efficiency maintains 97%, and the capacity at the 100th cycle can …

The Flip-Flop Behavior Of Acetonitrile At Au Electrode Surface Investigated By Sum Frequency Generation Vibrational Spectroscopy, Zhi Huang, Xin Tang, Gang-Hua Deng, En-Cai Zhou, Hong-Fei Wang, Yuan Guo

Journal of Electrochemistry

The electrochemical interface between liquid acetonitrile and polycrystal gold electrode is investigated by in situ infrared visible sum frequency generation spectroscopy (SFG-VS). The structure of acetonitrile adsorbed at polycrystal gold electrode surface is studied as a function of electrode potential. The SFG spectra of CH₃ group indicate acetonitrile orients in response to the electrode potential. The SFG signal of CH₃ group turns lower as the electrode potential changes from -700mV to 300mV, and vanishes around the 300mV(pzc), then becomes a negative signal above 500mV, which indicates that the orientation is predominately with the CH₃ group toward the …

Research Progress In Orthosilicates As Cathode Materials For Li-Ion Batteries, Dong-Ping Lv, Lin Wang, Yong Yang

Journal of Electrochemistry

Rechargeable Li-ion batteries fulfilling high-energy density, high safety, environmental friendliness, and low cost are demanded urgently for energy storage systems. Besides the structure stability arising from the strong Si-O covalent bond, environmental benignancy and low cost from the characteristics of Fe, Mn, Si elementals, orthosilicates (Li₂MSiO₄) show promising prospect to meet the demand of high-energy density for its two available Li+ per formula unit. Motivated by these significant advantages, Li₂MSiO₄ have been intensively investigated in the past few years. In the present work, we gave a review on the progress of orthosilicate research …

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Detection Of Acute Promyelocytic Leukemia Pml/Rarî± Fusion Gene Using Graphene Modified Glassy Carbon Electrode, Zhi-Xian Lian, Guang-Xian Zhong, Kun Wang, Ai-Lin Liu, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A graphene modified glassy carbon electrode (GCE) was prepared by electrochemical reduction of graphite oxide fixed on the surface of GCE. Then, the amino-group modified probe of acute promyelocytic leukemia (APL) PML/RARα fusion gene fragment was immobilized onto surface of the graphene modified GCE by coupling activating agent. With methylene blue (MB) as a novel electrochemical indicator, artificial APL PML/RARα fusion gene fragment was measured by differential pulse voltammetry (DPV). The result indicated graphene nanomaterial showed good sensitization on the signal of MB. The relationship between the reduction peak current of MB and the concentration of complementary strand was linear …

Influence Of Tert-Butylpyridine On The Band Energetics Of Nanostructured Tio2 Electrodes And The Photoelectrochemical Properties Of Dye-Seneitized Electrodes, Shu-Ming Yang, Ji-Chao Wang, Hui-Zhi Kou, Hong-Bin Xue, Hong-Jun Wang, Yu-Ling Guo

Journal of Electrochemistry

The flat band edges (Efb) of nanostructured TiO₂ electrodes in electrolyte solutions with tert-butylpyridine (TBP) of different concentrations have been determined with spectroelectrochemical technique. TBP played a role in band energetics of nanostructured TiO₂ electrodes. The Efb values of -2.25, -2.46 and -2.62 V were determined in three 0.2 mol•L^-1 tetrabutylammonium perchlorate (TBAP) acetonitrile electrolytes which contain 0, 0.2 and 0.4 mol•L^-1 TBP respectively. The addition of Li+ ions shifted Efb positively. The Efb values of -1.12, -1.22 and -1.30 V were determined in three 0.2 mol•L^-1 LiClO₄ acetonitrile electrolytes which contain 0, 0.2 …