Chemistry Commons^™

Surface Enhanced Raman Spectroscopic Studies Of Pyridine Adsorbed On Ti/Au@Sio2 Film Electrode, Min-Min Xu, Ke Liu, Qing-Hua Guo, Jian-Lin Yao

Journal of Electrochemistry

This study was performed based on shell-isolated nanoparticles-enhanced Raman spectroscopy (SHINERS) technology. The Au@SiO₂ nanoparticles were prepared and characterized by TEM and cyclic voltammetry. It was shown that the shell of SiO₂ was compact. The high quality signal measured by surface enhanced Raman spectroscopy (SERS) was obtained from the adsorbed pyridine on Ti/Au@SiO₂ electrode. The origin of the SERS signals was further confirmed by testing Pt and Ni electrodes. In addition, potential dependent adsorption behavior was investigated. It was found that pyridine was adsorbed parallel on the surface from -0.1 V to -0.6 V, and converted to …

Horseradish Peroxidase-Attapulgite Clay Nanocomposites: Fabrication And Application To Sensing The Extracellular H2O2 Released From Cells, Ping Wu, Chen-Xin Cai

Journal of Electrochemistry

The nanostructured attapulgite clay was employed as a support matrix for immobilizing horseradish peroxidase (HRP). FTIR and electrochemical methods demonstrated that HRP had been effectively assembled on attapulgite surface with the formation of HRP-attapulgite nanocomposites. The HRP-attapulgite hybrid was deposited on the glassy carbon (GC) electrode forming the HRP-attapulgite/GC electrode. Cyclic voltammetric results showed a pair of well-defined redox peaks, which were ascribed to direct electron transfer (DET) of HRP, with the formal potential E₀′ = -335 mV (vs. SCE) in the phosphate buffer solution (PBS, pH 7.0). The dependence of E₀′ on solution pH indicated …

The Ionic Diffusion Model For The Solid Oxide Cathode And Its Verification By The Electrolysis Of Ta2O5 In Molten Cacl2, Hua-Lin Chen, Zhi-Yong Wang, Xian-Bo Jin, George Z. Chen

Journal of Electrochemistry

The deoxidation speed of a solid oxide cathode in molten CaCl₂ can be estimated by the PRS steady diffusion model of O^2-, which correlates the deoxidation speed with the precursor porosity, P, the metal-to-oxide molar volume ratio, R, and the cathode volume shrinkage S. The PRS model indicates that the porosity of the oxide cathode has important influence on the deoxidation speed, and provides a very simple equation for the prediction of the optimal cathode porosity. For the electrolysis of Ta₂O₅, the porosity of the cathode is better to be within 50%. …

Effects Of Conformational Transformations On Electronic Transport Properties Of Optical Molecular Switches: An Ab Initio Study, Yuan-Yuan He, Jian-Wei Zhao

Journal of Electrochemistry

A series of model molecules with 4 kinds of conformational transformations have been investigated as optical molecular switches by using density functional theory combined with nonequilibrium Green’s function method. The theoretical calculations show that molecules after conformational transformations have photoswitching characteristics. We find that the photochromic molecules with the same conformational transformation usually have a similar current on/off state when they are applied as photoshwitches. Among these transformations, the molecular switch with E(“trans”)/Z(“cis”)-isomerisation of the NN double bond has the highest current on-off ratio. The influences of the energy gap (HLG) between the highest occupied molecular orbital (HOMO) and the …

23Na Mas Nmr Spectroscopic Study Of Na2Mnpo4F As Cathode Material For Sodium-Ion Battery, Xu Hou, Gui-Ming Zhong, Xiao-Chen Lin, Zi-Geng Liu, Xiao-Biao Wu, Yong Yang

Journal of Electrochemistry

The Na₂MnPO₄F is one of the promising cathode materials for the sodium ion batteries. In the paper, we employed the ex situ X-ray diffraction and solid state NMR techniques to study the charge and discharge processes of this material, including the crystal structure and sodium sites changes. The ex situ x-ray diffraction patterns showed that two new diffraction peaks could be observed at 31^o and 36^o indicating an intermediate phase formed with the extraction of Na⁺. From the ²³Na MAS NMR spectrum of the material, three peaks were seen at -209 …

Effects Of Oxygen Coverage And Hydrated Proton Model On The Dft Calculation Of Oxygen Reduction Pathways On The Pt(111) Surface, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

DFT calculation is used to study various possible steps in the oxygen reduction reaction (ORR), including the adsorption and dissociation process of O₂ and the serial protonation process of dissociated products to form H₂O on the Pt(111) surface. By using slabs of different sizes, and different numbers of pre-adsorbed oxygen atoms, the coverage effects on the pathways are investigated. The calculated results using different hydrated proton models are also compared. It is shown that the initial step of the ORR is the formation of a protonated end-on chemisorbed state of OOH*, which can transform to an unprotonated …

Synthesis, Characterization And Mechanistic Studies Of Biomolecules@Mesomofs, Yao Chen

USF Tampa Graduate Theses and Dissertations

Encapsulation of biomolecules is of great interest to research advances related to biology, physiology, immunology, and biochemistry, as well as industrial and biomedical applications such as drug delivery, biocatalysis, biofuel, food and cosmetics. Encapsulation provides functional characteristics that are not fulfilled by free biomolecules and stabilizes the fragile biomolecules. In terms of biocatalysis, solid support can often enhance the stability of enzymes, as well as facilitate separation and recovery for reuse while maintaining activity and selectivity. Various kinds of materials have been used for encapsulation of biomolecules, among which, porous materials are an important group. Metal-organic frameworks (MOFs) have attracted …

Study Of The Structure-Property Relationships That Determine The Effects Of Latexes And Starch Containing Latex Emulsions On The Performance Of The Barrier Coatings (Sub-Coat) For Paper, Joanna Marie Monfils

Master's Theses

The history of carbonless paper dates back to the 1940s. Before this, a carbon copy sheet was needed between sheets of paper to be able to produce one or more copies simultaneously during writing. The pressure from a pen or typewriter would help deposit the ink of the carbon paper onto the blank sheet of paper under the original written sheet to create a “carbon copy.” This method did however, have its disadvantages. Not only did it produce a limited number of copies, but it was also a messy process. So came the creative process of using microencapsulated dyes to …

Selection Of The Process Parameters For The Mass Plating Of Discrete Electronic Components, Ann Hopper

Articles

The miniaturisation of electronic components coupled with requirements for high temperature lead free soldering has forced the improvement of the termination finish of surface mount components to meet the critical demands of the electronic industry. In the present work the processing parameters necessary to plate miniature multilayer varistors (MLV’s) have been explored. The tooling selected was a “Rotary flow-thru’ plater” which achieved high volume plating with

Investigation Of Energy Alignment Models At Polymer Interfaces, Wenfeng Wang

USF Tampa Graduate Theses and Dissertations

The presented study investigated the Induced Density of Interface States (IDIS) model at different polymer interfaces by using photoemission spectroscopy in combination with electrospray deposition.

In recent years, organic electronics have attracted considerable attention due to their advantages of low-cost and easy-fabrication. The performance of such devices crucially depends on the energy barrier that controls the interface charge transfer. A significant effort has been made to explore the mechanisms that determine the direction and magnitude of charge transfer barriers in these devices. As a result of this effort, the IDIS model was developed to predict the energy alignment at metal/organic …

Homochiral Metal-Organic Materials: Design, Synthetic And Enantioseletive Separation, Shi-Yuan Zhang

USF Tampa Graduate Theses and Dissertations

Owing to the growing demand for enantiopurity in biological and chemical processes, tremendous efforts have been devoted to the synthesis of homochiral metal-organic materials (MOMs) because of their potential applications in chiral separation and asymmetric catalysis. In this dissertation, the synthetic strategies for homochiral MOMs are discussed keeping the focus on their applications. Two distinct approaches have been taken to synthesize chiral structures with different topologies and accessible cavities. The chiral MOMs have been utilized in enantioselective separation of racemates.

Chiral variants of the prototypal metal-organic framework MOF-5, δ-CMOF-5 and [lambda]-CMOF-5, have been synthesized by preparing MOF-5 in the presence …

Preparation And Electrochemical Performances Of Cofe2O4/Gns Nanocomposites As Anode Material For Lithium Ion Battery, Mo-Chao Cai, Sen-Rong Cai, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The CoFe₂O₄/GNS was synthesized by a simple one-pot solvothermal method. The results obtained by X-ray diffraction (XRD) and transmission electron microscopy (TEM) showed that the CoFe₂O₄ particles with sizes of 15 nm dispersed on the surface of graphene uniformly. Electrochemical tests indicated that the CoFe₂O₄/GNS nanocomposite exhibited excellent cyclic stability with almost 95.8% capacity retention after 100 cycles at the current density of 500 mA·g^-1 and delivered a high reversible capacity of 482 mAh·g^-1 at the current density of 2 A·g^-1.

Effect Of Temperature On The Self-Humidifying Open-Cathode Proton Exchange Membrane Fuel Cell, Si-Chen Zhao, Ben Wang, Qiu-Hong Jia, Ming Han, Yu-Hong Xie

Journal of Electrochemistry

Based on the experiments about the output characteristics of a home-made temperature-controlled PEMFC system with atmospheric pressure and no external humidifying condition in different loading voltages and operating temperatures, the optimum operating temperature at different loading voltages can be obtained by tracking the output characteristics of PEMFC operating over a range of temperatures. By analyzing the fitted data the kinetic parameters are evaluated and the effect of different operating temperatures on the PEMFC performance is discussed from a view of electrode kinetics.

Preparation Of Pt/H-Tio2 Catalyst With Improved Catalytic Performance For Methanol Electrooxidation, Jin Han, Zhi-You Zhou, Qiang Wang, Miao-Qiang Lv, Chi Chen, Shi-Gang Sun

Journal of Electrochemistry

White TiO₂ nanorods were synthesized by hydrothermal method with TiCl₄ as a precursor. As-synthesized TiO₂ nanorods were further subjected to high-temperature (550 ^oC) heat treatment for 2 h under H₂ atmosphere to prepare gray black hydrogen-treated TiO₂ (H-TiO₂) nanorods with oxygen vacancies and Ti³⁺ interstitial atoms. The Pt nanoparticles of 1.9 nm were supported on these two types of TiO₂ nanorods to form Pt/TiO₂ and Pt/H-TiO₂ catalysts. XRD data indicates that the crystal structure of TiO₂ was still reserved as rutile after hydrogen treatment, but the surface …

An Equivalent Circuit Model For Redox Flow Battery Stack, Dong-Jiang You, Hua-Min Zhang

Journal of Electrochemistry

This paper introduces an equivalent circuit model for a redox flow battery stack. The model combines the electrochemical reaction of the battery cell and the shunt current of the battery stack. An all-vanadium redox flow battery stack of 1kW rated output power is tested through transient response and self-discharge experiments. All the parameters used for the modeling are obtained. Calculated shunt current and distribution of calculated battery voltage are shown in the results. It is concluded that the impedance of the battery stack can be obtained by the experimental results of the transient response and self-discharge measurements. The capacity lose …

Effects Of Carbon Interlayer On Electrochemical Performance Of Lithium-Sulfur Cell, Jin-Peng Yu, Ming Zhang, Fei Ding, Zhi-Yuan Tang, Xing-Jiang Liu

Journal of Electrochemistry

Three kinds of conductive carbon films were prepared with Super-P (SP), KB and MWCNTs, and then the as-prepared carbon films were applied as an interlayer between a sulfur electrode and a separator for constructing a coin-type lithium-sulfur (Li-S) cell, respectively. The assessment results show that all the cells delivered the reversible capacities higher than 800 mAh·g^-1 after 40 cycles when the sulfur loading was up to 80% (by mass) in the sulfur electrode. Due to significant differences of physical properties among the carbon materials, the cell with a KB interlayer exhibited higher electrochemical polarization; the cycling performance of the …

Effect Of Al-Doping In Li-Rich Material Li1.2Mn0.543Co0.078Ni0.155Al0.030O2 For Lithium-Ion Batteries, Xiao-Xi Jin, Yi-Xiao Li, Yong Yang, Zhou-Cheng Wang

Journal of Electrochemistry

The Al-doped 0.5Li₂MnO₃·0.5Li(Mn_0.4Co_0.2Ni_0.4)O₂ compounds were successfully synthesized as cathode materials for lithium-ion batteries. The pristine and Al-doped materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), inductively coupled plasma-atomic emission spectrometry (ICP-AES) and laser Raman spectroscopy. The results indicated that all the prepared materials were indexed as a hexagonal structure with R-3m space group, and Al element had been introduced into lattice. When cycled at 180 mA·g^-1 (1 C-rate), the capacity retention of 4% (by mole) Al-doped 0.5Li₂MnO₃·0.5Li(Mn_0.4Co_0.2Ni …

Electrodeposition Of Copper From A Choline Chloride Based Ionic Liquid, Rostom Ali M., Ziaur Rahman Md., Sankarsaha S.

Journal of Electrochemistry

The electrodeposition of copper from a solution containing copper chloride in either an ethylene glycol (EG)-choline chloride based or a urea-choline chloride based ionic liquid has been carried out onto a steel cathode by constant current and constant potential methods at room temperature. The influences of various experimental conditions on electrodeposition and the morphology of the deposited layers have been investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). It is shown that very smooth, shiny and dense with good adherence and bright metallic coloured copper coatings can be obtained from both EG and urea based ionic liquids at …

Electrocatalytic Oxidation Of Glycerol At The Platinum Electrode Modified With An Nd-Fe-Moo42- Cyano-Bridged Mixed Coordination Polymer, Yong-Jun Ma, Yu-Xiu Tian, Jing Liu, Min Zhou, Jing Ding, Zhi-Mei Jin, Xiang-Mei Wang

Journal of Electrochemistry

A platinum electrode decorated with the ordered Nd-Fe-MoO₄^2- cyano-bridged mixed coordination polymer was successfully prepared by electrodeposition in virtue of the lyotropic liquid crystal soft template methods, and electrocatalytic oxidation behavior of glycerol was investigated on the chemically modified electrode by cyclic voltammetry. The influences of experimental factors such as the concentrations of H⁺ and SO₄^2- in electrolytes, glycerol concentration and scan rate on the electrocatalytic activity of glycerol at the modified electrode were also studied. It indicated that the proper amount of SO₄^2- in weakly acidic electrolyte could help to improve the …

Application Of Ionic Liquid Pp14Tfsi In Electrolyte Systems For Rechargeable Mg Batteries, Jin-Jie Zhu, Fei-Fei Wang, Yong-Sheng Guo, Jun Yang, Yan-Na Nuli, Jiu-Lin Wang

Journal of Electrochemistry

A phenolated-based Mg salt was prepared. The mixture of THF and N-methyl-N-butyl-piperidinium bis(trifluoromethanesulfonyl)imide (PP14TFSI) serves as the mixed solvent instead of pure THF for rechargeable Mg batteries systems. This new type of electrolyte system not only has optimal reversibility of Mg, but also owns a wide electrochemical window (2.7 V vs. Mg) and high ionic conductivity (7.77 mS·cm^-1). More importantly, the addition of Ionic Liquid suppresses the volatility of THF and improves the safety of rechargeable Mg batteries. The result shows that the mixture of THF and piperidyl-based Ionic Liquid could be regarded as a good solvent candidate …

Electro-Catalytic Oxidation Of Hydrogen Peroxide On Au/ L-Methionine /Gc Electrode, Jian-Feng Fan, Xue-Mei Luo, Jing Li, Lou-Zhen Fan

Journal of Electrochemistry

The modified electrodes have been fabricated by generation of Au nanoparticle chains, which was produced by reaction between HAuCl4 and sodium citrate without any additional capping agents or surfactants. The self-assembled Au nanoparticles were attached to the surface of glassy carbon electrode (GCE) layer by layer, using L-methionine (L-Met), thiourea (TU), allyl thiourea (ATU) and polyvinylpyrrolidone (PVP) as a crosslinking agent, respectively. The experimental results showed that the electrochemical performance of the different modified electrodes varied in [Fe(CN)₆]^3-/4- solution. The Au/L-Met/GCE exhibited an excellent electrochemical property, which is superior to other modified electrodes. In addition, the catalysis …

Synthesis Of Platinum Nanocrystallites And Possible Electrocatalytic Properties For Methanol, Lei-Lei Lu, Bao-Zhong Du, Sha Sun, Jin-Fen Niu, Jie Zhao

Journal of Electrochemistry

Platinum nanocrystallites were synthesized by the colloidal method using oxamide as the stabilizer. The morphologies and electrocatalytic performances for methanol of platinum nanocrystallites prepared at different pH values and with different reactant ratios of precursor and stabilizer were investigated. It was found that the platinum nanocrystallites synthesized at pH=5 and with the reactant ratio of 1:20 showed the best electrocatalytic activity for methanol. The peak current density reached up to 1709 μA·cm^-2. Furthermore, the electrocatalytic activity of platinum nanocrystallites for methanol reduced significantly although the cyclic voltammograms in the blank solution were not obviously changed after exposing in …

Effect Of Multivalent Ions On The Swelling And Mechanical Behavior Of Superabsorbent Polymers (Saps) For Mitigation Of Mortar Autogenous Shrinkage, Qian Zhu

Open Access Theses

The chemical and physical structure-property relationships of model superabsorbent polymer (SAP) hydrogels were characterized with respect to swelling behavior and mechanical properties in different ionic solutions (Na+ , Ca2+ , and Al3+ ). The model hydrogels were composed of poly(sodium acrylate-acrylamide) (PANa-PAM) copolymer with varying concentrations of PANa (0, 17, 33, 67, and 83 wt.%) and covalent crosslinking densities of 1, 1.5, and 2 wt.%. By synthesizing the hydrogels in-house, systems with independently tunable amounts of covalent crosslinking and anionic functional groups were created, allowing for the relative effects of covalent and ionic crosslinking on the properties of the hydrogels …

[M3(Μ3-O)(O2cr)6] And Related Trigonal Prisms: Versatile Molecular Building Blocks For 2-Step Crystal Engineering Of Functional Metal-Organic Materials, Alexander Schoedel

USF Tampa Graduate Theses and Dissertations

Metal-organic materials (MOMs) assembled from metal-based building blocks and organic linkers have attracted much interest due to their large pore dimensions and their enormous structural diversity. In comparison to their inorganic counterparts (zeolites), these crystalline materials can be easily modified to tailor pore dimensions and functionality for specifically targeted properties.

The work presented herein encompasses the development of a synthetic 2-step process for the construction of novel families of MOMs or 'platforms' and allow us exquisite design and control over the resulting network topologies. Examples of cationic mesoporous structures were initially exploited, containing carboxylate based centers connected by metal-pyridine bonds. …

Electrochemical Performance Of Si-C Composites Prepared By Discharge-Plasma Assisted Milling, Yu-Long Chen, Ren-Zong Hu, Hui Liu, Wei Sun, Min Zhu

Journal of Electrochemistry

Silicon-carbon (Si-C) composites, with microstructure of multi-scaled Si particles being homogenously dispersed in micro-sized carbon matrix, had been prepared by dielectric barrier discharge plasma assisted two-step milling for the first time. The Si-C composite anode had a discharge capacity of 1259 mAh·g^-1 at the first cycle, while the capacity retained 474 and 396 mAh·g^-1 after 20 and 100 cycles, respectively. Charge-discharge curves and AC impedance response indicated that both silicon and carbon phases in the composite anode were involved during the lithiation/delithiation reactions and the electron transport resistance in the Si-C composite anode was much lower than that …

Study On Carbon Supported Pd Catalysts Modified By Phosphomolybdic Acid For H2O2 Electrocatalytic Reduction, Li-Mei Sun, Cheng Zhang, Ying-Rong Bao, Hong-Xia Li

Journal of Electrochemistry

The Pd/C catalyst was prepared with the chemical reduction method, and phosphomolybdic acid (PMA) was modified on the Pd/C catalyst using the dipping method. The compositions and structures of the Pd/C and Pd/C modified by phosphomolybdic acid (PMA-Pd/C) catalysts were characterized with X-ray diffraction and Fourier Transform infrared spectroscopy analyses. The electrocatalytic activity and stability of the catalysts for the reduction of hydrogen peroxide (H₂O₂) were studied using cyclic voltammetry and chronoamperometry. The results showed that the phosphomolybdic acid was tightly fixed on the surface of Pd/C catalyst through the chemical interaction. The eletrocatalytic activity of …

Preliminary Study On Morphology Controllability Of Electrochemically Prepared Polyaniline By Using Aniline Aimer, Yang Zuo, Kang Shi

Journal of Electrochemistry

Employing of aniline dimer (N-phenyl-p-phenylenediamine, NPD) as the starting monomer, polyaniline was electrochemically synthesized on the surface of glassy carbon electrode in acetonitrile-aqueous mixing solutions（20% by volume）containing 1 mol·L^-1 HClO₄. Experimental results demonstrated that the polymerization of NPD occurs at the potentials about 0.2 V lower than those of aniline monomer. Furthermore, the resulting polyaniline has higher morphology controllability than those synthesized by using aniline as the stating monomer. The uniform polyaniline nanoparticles (30 nm in diameter), ultralong nanowires (length > 5 μm, 50 nm in diameter) or large area nanosheets (4 μm in length, 2 μm in …

Electrochemical Oxidation Of Ammonium Nitrite In Absorption Solution Of Flue Gas, Yong-Hong Lu, Xiao-Bo Dong, Li-Sha Wang, Yan Liu, Chen-Jian Zhu, Hai-Bo Xu

Journal of Electrochemistry

In order to make full uses of ammonium nitrite in absorption solution from flue gas simultaneous desulfurization, denitrification and demercurization processes, here the electrochemical oxidation method was used to transform ammonium nitrite into ammonium nitrate. By using polarization curve, cyclic voltammogram and galvanostatic methods, suitable electrode materials were evaluated and chosen. The influence of electrolyte composition was discussed and the appropriate process parameters were obtained. Finally, the effect of electrochemical oxidation was confirmed by chemical analysis method. In 0.05 mol·L^-1 NaNO₂ + 0.05 mol·L^-1 (NH₄)₂SO₄ simulated absorption solution (5 L, pH = …

Preparation Of High Performance Porous Silicon Powders By Etching Al-Si Alloy In Acid Solution For Lithium Ion Battery, Shi-Ji Hao, Chun-Li Li, Kai Zhu, Ping Zhang, Zhi-Yu Jiang

Journal of Electrochemistry

Porous silicon powders prepared by etching Al-Si alloy using an acid solution was reported in the first time. The morphology and structure of as-obtained material were investigated using scanning electron microscopy (SEM) and X-ray diffraction (XRD) method. It was found that the spongy porous silicon powders presented well crystalline structure and consisted of nano-Si particles. The particle size of porous Si powders was about 20 μm, and the specific surface area was 102.7 m²·g^-1. The electrochemical properties of porous silicon powders were evaluated as an anode material for lithium ion batteries. The material proportion in the …

Pulse Electrodeposition Of Pd-Ni Alloy Nanoparticles For Electrocatalytic Oxidation Of Formic Acid, Fang-Zu Yang, Jun-Pei Yue, Zhong-Qun Tian, Shao-Min Zhou

Journal of Electrochemistry

The Pd-Ni alloy nanoparticles with nickel atomic contents of 12.0%, 16.4% and 22.6% were successfully electrodeposited from a Pd-Ni alloy electrolyte by square wave pulse plating. The alloy nanoparticles were in the spherical shape with a diameter of 50 ~ 80 nm. As the growth potential of the alloy was negatively shifted, the nickel content of the alloy was increased, and the size of the nanoparticles was almost the same, whereas the number, the degree of crosslinking and the real active area of the nanoparticles were increased. As the nickel content of the alloy nanoparticles increased, the peak current for …