Physical Sciences and Mathematics Commons^™

Battery Design, Construction, And Characterization For Small Motor Use Focusing On Anodic Zinc For Electron Flow, Amber Veach

Chemical Engineering Undergraduate Honors Theses

This thesis explores the construction, characterization, and application of anodic zinc batteries for powering a small electric motor for the ChemE Car competition. Two zinc galvanic cell batteries were studied: zinc-carbon and zinc-air batteries. Prototype batteries were constructed and tested for voltage, amperage, and power production. In the zinc-carbon trials, a 3:1 mixture of manganese dioxide and graphite was determined to be the best cathode for power production. The size which allowed for sufficient power while maintaining the smallest footprint on the car was a zinc can six cm tall and two cm in diameter. Analysis of paper zinc-air battery …

Enhanced Electrochemical Performances Of Hollow-Structured N-Doped Carbon Derived From A Zeolitic Imidazole Framework (Zif-8) Coated By Polydopamine As An Anode For Lithium-Ion Batteries, Da-Won Lee, Achmad Yanuar Maulana, Chaeeun Lee, Jungwook Song, Cybelle M. Futalan, Jongsik Kim

Environmental Science Faculty Publications

Doping heteroatoms such as nitrogen (N) and boron (B) into the framework of carbon materials is one of the most efficient methods to improve the electrical performance of carbon-based electrodes. In this study, N-doped carbon has been facilely synthesized using a ZIF-8/polydopamine precursor. The polyhedral structure of ZIF-8 and the effective surface-coating capability of dopamine enabled the formation of N-doped carbon with a hollow structure. The ZIF-8 polyhedron served as a sacrificial template for hollow structures, and dopamine participated as a donor of the nitrogen element. When compared to ZIF-8-derived carbon, the HSNC electrode showed an improved reversible capacity of …

Lithium Storage Performance Of High Capacity Material Si@CPzs In Lithium Ion Batteries, Qing-Nuan Zhang, Fang-Fang Zhang, Hong-Xia Li, Bing-Jun Yang, Xiao-Cheng Li, Juan Yang

Journal of Electrochemistry

Carbon layers with different thicknesses were introduced into the surfaces of silicon (Si) nanoparticles by sol-gel method using poly (cyclotriphosphazene-co-4, 4'-sulfonyldiphenol) as the carbon source. Technologies of X-ray diffraction, thermo-gravimetric analysis, Brunauer-Emmett-Teller and transmission electron microscopy were employed to analyze the structures and components of the as-prepared Si@C_PZS composites. Electrochemical performance of Si@C_PZS with different carbon thicknesses was studied. The results showed that Si@C_PZS with carbon thickness of 10 nm possessed the best performance. Its capacity remained 940 mAh·g -1 after 290 cycles under 500 mA·g -1. As the addictive, the graphite-based anode contained 30% of Si@C …

Strategies To Improve The Electrochemical Of Performance Transition Metal Compounds As Anode Materials For Li-Ion Batteries, Noemi Dominguez

Open Access Theses & Dissertations

Nowadays, our society depends on fossil fuels as the main energy source. However, depletion, price fluctuations, and other concerns, such as global warming, have led to an exhaustive research for renewable energy resources. Here is where electrochemical energy systems play a critical role since they can provide power when renewable energy is not available. Among these electrochemical energy storage systems Li-ion batteries (LIBs) have shown higher volumetric, gravimetric, and power density capacities over other battery systems.

However, commercial LIBs are still relying on graphite base materials for the anode. However, graphite possesses a low specific capacity. Recently, transition metal compounds …

Synthesis Of Cose2-Snse2 Nanocube-Coated Nitrogen-Doped Carbon (Nc) As Anode For Lithium And Sodium Ion Batteries, Jin Bai, Huimin Wu, Shiquan Wang, Guangxue Zhang, Chuanqi Feng, Hua-Kun Liu

Australian Institute for Innovative Materials - Papers

CoSe2-SnSe2/NC nanocubes (CSNC@NC) coated by nitrogen-doped carbon (NC) were synthesized successfully by an ordinary pyrazole polymerization and carbonization process. In comparison with bare CSNC, the CSNC@NC composite exhibited good structural stability and improved electrical conductivity when used as anode. The CSNC@NC electrode showed a stable Li storage capacity (730.41 mAh g−1 over 100 cycles at 0.2 A g−1) and excellent rate performance (402.10 mAh g−1 at 2 A g−1). For Na storage, the discharge capacity could be maintained 279.3 mAh g−1 over 100 cycles at 0.2 A g−1; the lower capacity than that for Li storage maybe caused by the …

Research Progresses In Improvement For Low Temperature Performance Of Lithium-Ion Batteries, Yue-Ru Gu, Wei-Min Zhao, Chang-Hu Su, Chuan-Jun Luo, Zhong-Ru Zhang, Xu-Jin Xue, Yong Yang

Journal of Electrochemistry

Lithium-ion batteries (LIBs) have become a new research hotspot due to their high energy density and long service life. However, the temperature characteristics, especially the poor performance at low temperatures, have seriously limited their wider applications. In this report, the research progresses in the low temperature performance of LIBs are reviewed. The main existing limitations of LIBs at low temperatures were systematically analyzed, and followed by discussion on the recent improvements in low temperature performances by developing novel cathode, electrolyte, and anode materials. The developments for improving the low temperature performance of LIBs are prospected. The three most important factors …

Co3(Hcoo)6@Rgo As A Promising Anode For Lithium Ion Batteries, Heng Jiang, Jing-Min Fan, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Metal–organic framework(MOF) is a kind of novel electrode materials for lithium ion batteries. Here, a composite material Co₃(HCOO)₆@rGO was synthesized for the first time by in situ loading of Co₃(HCOO)₆ on rGO (reduced oxide graphene) through a solution chemistry method. As an anode material for lithium ion batteries, it exhibited an excellent cycle stability as well as a large reversible capacity of 926 mAh·g^-1 at a current density of 500 mA·g^-1 after 100 cycles within the voltage range of 0.02 ~ 3.0 V vs. Li/Li⁺ with a good rate capability. …

In Operando Mechanism Analysis On Nanocrystalline Silicon Anode Material For Reversible And Ultrafast Sodium Storage, Lei Zhang, Xianluo Hu, Chaoji Chen, Haipeng Guo, Xiaoxiao Liu, Gengzhao Xu, Haijian Zhong, Shuang Cheng, Peng Wu, Jiashen Meng, Yunhui Huang, Shi Xue Dou, Hua-Kun Liu

Australian Institute for Innovative Materials - Papers

Presently, lithium-ion batteries (LIBs) are the most promising commercialized electrochemical energy storage systems. Unfortunately, the limited resource of Li results in increasing cost for its scalable application and a general consciousness of the need to find new type of energy storage technologies. Very recently, substantial effort has been invested to sodium-ion batteries (SIBs) due to their effectively unlimited nature of sodium resources. Furthermore, the potential of Li/Li+ is 0.3 V lower than that of Na/Na+, which makes it more effective to limit the electrolyte degradation on the outer surface of the electrode.[1] Nevertheless, one major obstacle for the commercial application …

Hierarchical Porous Nio/B-Nimoo4 Heterostructure As Superior Anode Material For Lithium Storage, Zhijian Wang, Shilin Zhang, Hai Zeng, Haimin Zhao, Wei Sun, Meng Jiang, Chuanqi Feng, Jianwen Liu, Tengfei Zhou, Yang Zheng, Zaiping Guo

Australian Institute for Innovative Materials - Papers

Ternary transition metal oxides (TTMOs) have attracted considerable attention for rechargeable batteries because of their fascinating properties. However, the unsatisfactory electrochemical performance originating from the poor intrinsic electronic conductivity and inferior structural stability impedes their practical applications. Here, the novel hierarchical porous NiO/β-NiMoO4heterostructure is fabricated, and exhibits high reversible capacity, superior rate capability, and excellent cycling stability in Li-ion batteries (LIBs), which is much better than the corresponding single-phase NiMoO4and NiO materials. The significantly enhanced electrochemical properties can be attributed to its superior structural characteristics, including the large surface area, abundant pores, fast charge transfer, and catalytic effect of the …

Surfactant Driven Assembly Of Freeze-Casted, Polymer-Derived Ceramic Nanoparticles On Grapehene Oxide Sheets For Lithium-Ion Battery Anodes, Ali Zein Khater

Honors Undergraduate Theses

Traditional Lithium-Ion Batteries (LIBs) are a reliable and cost-efficient choice for energy storage. LIBs offer high energy density and low self-discharge. Recent developments in electric-based technologies push for replacing historically used Lead-Acid batteries with LIBs. However, LIBs do not yet meet the demands of modern technology. Silicon and graphene oxide (GO) have been identified as promising replacements to improve anode materials. Graphene oxide has a unique sheet-like structure that provides a mechanically stable, light weight material for LIB anodes. Due to its structure, reduced graphene oxide (rGO) is efficiently conductive and resistive to environmental changes. On the other hand, silicon-based …

Nuclear Magnetic Resonance Studies Of Electrode And Electrolyte Materials For Li-Ion Batteries, Lisa Cirrincione

Dissertations, Theses, and Capstone Projects

In this thesis, Nuclear Magnetic Resonance (NMR) spectroscopic techniques are used to study lithium electrode and electrolyte materials for advanced rechargeable lithium ion batteries. Three projects are described in this thesis. The first involves ²³Na and ³⁷Al static and magic angle spinning NMR studies of NaAlH₄/C anode materials for advanced rechargeable batteries. The second project is a study of paramagnetic lithium transition-metal phosphate cathode materials for Li-ion batteries, where ⁷Li, and ³¹P single crystal NMR was used in order to obtain detailed information on the local electronic and magnetic environments. The third project investigates …

Phosphorus-Based Materials As The Anode For Sodium-Ion Batteries, Fuhua Yang, Hong Gao, Jun Chen, Zaiping Guo

Australian Institute for Innovative Materials - Papers

No abstract provided.

Ultra-Light And Flexible Pencil-Trace Anode For High Performance Potassium-Ion And Lithium-Ion Batteries, Zhixin Tai, Yajie Liu, Qing Zhang, Tengfei Zhou, Zaiping Guo, Hua-Kun Liu, Shi Xue Dou

Australian Institute for Innovative Materials - Papers

Engineering design of battery configurations and new battery system development are alternative approaches to achieve high performance batteries. A novel flexible and ultra-light graphite anode is fabricated by simple friction drawing on filter paper with a commercial 8B pencil. Compared with the traditional anode using copper foil as current collector, this innovative current-collector-free design presents capacity improvement of over 200% by reducing the inert weight of the electrode. The as-prepared pencil-trace electrode exhibits excellent rate performance in potassium-ion batteries (KIBs), significantly better than in lithium-ion batteries (LIBs), with capacity retention of 66% for the KIB vs. 28% for the LIB …

Lignin-Based Li-Ion Anode Materials Synthesized From Low-Cost Renewable Resources, Nicholas William Mcnutt

Doctoral Dissertations

In today’s world, the demand for novel methods of energy storage is increasing rapidly, particularly with the rise of portable electronic devices, electric vehicles, and the personal consumption and storage of solar energy. While other technologies have arguably improved at a rate that is exponential in accordance with Moore’s law, battery technology has lagged behind largely due to the difficulty in devising new electric storage systems that are simultaneously high performing, inexpensive, and safe.

In order to tackle these challenges, novel Li-ion battery anodes have been developed at Oak Ridge National Laboratory that are made from lignin, a low-cost, renewable …

A Green And Facile Way To Prepare Granadilla-Like Silicon-Based Anode Materials For Li-Ion Batteries, Lei Zhang, Ranjusha Rajagopalan, Haipeng Guo, Xianluo Hu, S X. Dou, Hua-Kun Liu

Australian Institute for Innovative Materials - Papers

A yolk-shell-structured carbon@void@silicon (CVS) anode material in which a void space is created between the inside silicon nanoparticle and the outer carbon shell is considered as a promising candidate for Li-ion cells. Untill now, all the previous yolk-shell composites were fabricated through a templating method, wherein the SiO2 layer acts as a sacrificial layer and creates a void by a selective etching method using toxic hydrofluoric acid. However, this method is complex and toxic. Here, a green and facile synthesis of granadilla-like outer carbon coating encapsulated silicon/carbon microspheres which are composed of interconnected carbon framework supported CVS nanobeads is reported. …

Si-Containing Precursors For Si-Based Anode Materials Of Li-Ion Batteries: A Review, Lei Zhang, Xiaoxiao Liu, Qianjin Zhao, Shi Xue Dou, Hua-Kun Liu, Yunhui Huang, Xianluo Hu

Australian Institute for Innovative Materials - Papers

Lithium-ion batteries with high energy density are in demand for consumer electronics, electric vehicles, and grid-scale stationary energy storage. Si is one of the most promising anode materials due to its extremely high specific capacity. However, the full application of Si-based anode materials is limited by poor cycle life and rate capability resulted from low ionic/electronic conductivity and large volume change over cycling. In recent years, great progress has been made in improving the performance of Si anodes by employing nanotechnology. The preparation methods are essentially important, in which the precursors used are crucial to design and control the microstructure …

Mos2 With An Intercalation Reaction As A Long-Life Anode Material For Lithium Ion Batteries, Zhe Hu, Qiannan Liu, Weiyi Sun, Weijie Li, Zhanliang Tao, Shulei Chou, Jun Chen, S X. Dou

Australian Institute for Innovative Materials - Papers

MoS2 with expanded layers was synthesized and characterized as an anode material for lithium ion batteries in an ether-based electrolyte by cutting off the terminal discharge voltage at 1.0 V to prevent a MoS2 conversion reaction. The as-prepared MoS2 achieved 96% capacity retention even after 1400 cycles and showed good performance in a full cell with LiCoO2 as the counter electrode.

Synthesis Of Different Cuo Nanostructures By A New Catalytic Template Method As Anode Materials For Lithium-Ion Batteries, Xiaohang Ma, Shuang Zeng, Bangkun Zou, Xin Liang, Jia-Ying Liao, Chunhua Chen

Australian Institute for Innovative Materials - Papers

CuO powders composed of different rod-like clusters or dandelion-like nanospheres are prepared by a low-temperature thermal decomposition process of Cu(OH)2 precursors, which are obtained via a catalytic template method. A tentative mechanism is proposed to explain the formation and transformation of different Cu(OH)2 nanostructures. X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, field-emission scanning electron microscopy, transmission electron microscopy, infrared spectra analysis, Brunauer-Emmett-Teller measurements, and galvanostatic cell cycling are employed to characterize the structures and electrochemical performance of these CuO samples. The results show that these CuO samples obtained after 500 °C calcination have a stable cycling performance with a reversible …

3d Fe2(Moo4)3 Microspheres With Nanosheet Constituents As High-Capacity Anode Materials For Lithium-Ion Batteries, Hao Zheng, Shiqiang Wang, Jiazhao Wang, Jun Wang, Lin Li, Yun Yang, Chuanqi Feng, Ziqi Sun

Australian Institute for Innovative Materials - Papers

Three-dimensional (3D) Fe2(MoO4)3 microspheres with ultrathin nanosheet constituents are first synthesized as anode materials for the lithium-ion battery. It is interesting that the single-crystalline nanosheets allow rapid electron/ion transport on the inside, and the high porosity ensures fast diffusion of liquid electrolyte in energy storage applications. The electrochemical properties of Fe2(MoO4)3 as anode demonstrates that 3D Fe2(MoO4)3 microspheres deliver an initial capacity of 1855 mAh/g at a current density of 100 mA/g. Particularly, when the current density is increased to 800 mA/g, the reversible capacity of Fe2(MoO4)3 anode still arrived at 456 mAh/g over 50 cycles. The large and reversible …

Crystalline Tio2@C Nanosheet Anode With Enhanced Rate Capability For Lithium-Ion Batteries, Fan Yang, Yuxuan Zhu, Xiu Li, Chao Lai, Wei Guo, Jianmin Ma

Australian Institute for Innovative Materials - Papers

TiO2@C nanosheets have been obtained by a facile solvothermal method using titanate butoxide and hydrofluoric acid as precursors, followed by our novel carbon coating technique using oleic acid as the carbon source. The TiO2@C nanosheet anode shows a high discharge capacity of 145.8 mA h g-1 after 50 cycles and excellent rate capability.

Yolk-Shell Silicon-Mesoporous Carbon Anode With Compact Solid Electrolyte Interphase Film For Superior Lithium-Ion Batteries, Jianping Yang, Yunxiao Wang, Shulei Chou, Renyuan Zhang, Yanfei Xu, Jianwei Fan, Weixian Zhang, Hua-Kun Liu, Dongyuan Zhao, S X. Dou

Australian Institute for Innovative Materials - Papers

Silicon as an electrode suffers from short cycling life, as well as unsatisfactory rate-capability caused by the large volume expansion (~400%) and the consequent structural degradation during lithiation/delithiation processes. Here, we have engineered unique void-containing mesoporous carbon-encapsulated commercial silicon nanoparticles (NPs) in yolk-shell structures. In this design, the silicon NPs yolk are wrapped into open and accessible mesoporous carbon shells, the void space between yolk and shell provides enough room for Si expansion, meanwhile, the porosity of carbon shell enables fast transport of Li+ ions between electrolyte and silicon. Our ex-situ characterization clearly reveals for the first time that a …

A New Strategy For Achieving A High Performance Anode For Lithium Ion Batteries-Encapsulating Germanium Nanoparticles In Carbon Nanoboxes, Dan Li, Hongqiang Wang, Hua-Kun Liu, Zaiping Guo

Australian Institute for Innovative Materials - Papers

A novel strategy to improve the electrochemical performance of a germanium anode is proposed via encapsulating germanium nanoparticles in carbon nanoboxes by carbon coating the precursor, germanium dioxide cubes, and then subjecting them to a reduction treatment. The complete and robust carbon boxes are shown to not only provide extra void space for the expansion of germanium nanoparticles after lithium insertion but also offer a large reactive area and reduced distance for the lithium diffusion. Furthermore, the thus-obtained composite, composed of densely stacked carbon nanoboxes encapsulating germanium nanoparticles (germanium at carbon cubes (Ge at CC)), exhibits a high tap density …

Hollow Carbon Spheres With Encapsulated Germanium As An Anode Material For Lithium Ion Batteries, Dan Li, Chuanqi Feng, Hua-Kun Liu, Zaiping Guo

Australian Institute for Innovative Materials - Papers

A novel composite consisting of hollow carbon spheres with encapsulated germanium (Ge@HCS) was synthesized by introducing a germanium precursor into the porous-structured hollow carbon spheres. The carbon spheres not only function as a scaffold to hold the germanium and thus maintain the structural integrity of the composite, but also increase the electrical conductivity. The voids and vacancies that are formed after the reduction of germanium dioxide to germanium provide free space for accommodating the volume changes during discharging-charging processes, thus preventing pulverization. The obtained Ge@HCS composite exhibits excellent lithium storage performance, as revealed by electrochemical evaluation.

Manganese Dioxide-Anchored Three-Dimensional Nitrogen-Doped Graphene Hybrid Aerogels As Excellent Anode Materials For Lithium Ion Batteries, Zhu Yin Sui, Caiyun Wang, Kewei Shu, Quan-Sheng Yang, Yu Ge, Gordon G. Wallace, Bao Hang Han

Australian Institute for Innovative Materials - Papers

The capacity of manganese dioxide (MnO₂) deteriorates with cycling due to the irreversible changes induced by the repeated lithiation and delithiation processes. To overcome this drawback, MnO₂/nitrogen-doped graphene hybrid aerogels (MNGAs) were prepared via a facile redox process between KMnO₄ and carbon within nitrogen-doped graphene hydrogels. The three-dimensional nitrogen-doped graphene hydrogels were prepared and utilized as matrices for MnO₂ deposition. The MNGAs-120 obtained after a deposition time of 120 min delivered a very high discharge capacity of 909 mA h g^-1 after 200 cycles at a current density of 400 mA g^{-1 …}

Unique Urchin-Like Ca2ge7o16 Hierarchical Hollow Microspheres As Anode Material For The Lithium Ion Battery, Dan Li, Chuanqi Feng, Hua-Kun Liu, Zaiping Guo

Australian Institute for Innovative Materials - Papers

Germanium is an outstanding anode material in terms of electrochemical performance, especially rate capability, but its developments are hindered by its high price because it is rare in the crust of earth, and its huge volume variation during the lithium insertion and extraction. Introducing other cheaper elements into the germanium-based material is an efficient way to dilute the high price, but normally sacrifice its electrochemical performance. By the combination of nanostructure design and cheap element (calcium) introduction, urchin-like Ca₂Ge₇O₁₆ hierarchical hollow microspheres have been successfully developed in order to reduce the price and maintain the …

Growth Of Mos2@C Nanobowls As A Lithium-Ion Battery Anode Material, Chunyu Cui, Xiu Li, Zhe Hu, Jiantie Xu, Hua-Kun Liu, Jianmin Ma

Australian Institute for Innovative Materials - Papers

Layered MoS2 has attracted much attention as a promising anode material for lithium ion batteries. The intrinsically poor electrical/ionic conductivity, volume expansion and pulverization, stress accumulation and unstable solid-electrolyte interface formation within MoS2 electrodes during the lithiation-delithiation process significantly result in their fast capacity fading, poor rate capability and cycle life. To address these critical issues, a novel nanobowl structure for MoS2 with a carbon coating (MoS2@C-400, 500, 600) is successfully fabricated by a facile solvothermal method, followed by a post-annealing process. The fabricated MoS2@C-600 and MoS2@C-500 exhibited high reversible capacities of 1164.4 and 1076.4 mA h g-1 at 0.2C, …

Enhanced Electrocatalytic Efficiency Of C/Mwnts For Methanol Oxidation Using Ni Deposited On Mwnts, Murat Farsak, Gülfeza Kardaş

Turkish Journal of Chemistry

The power density of direct methanol fuel cells (DMFCs) can be changed by using different anode materials. Especially porous materials are preferred for the anode. In the present study, multiwall carbon nanotubes were first injected into graphite. Then, by depositing nickel, a catalyst was prepared for use as the anode material of the DMFC. This catalyst was named Ni@MWNTs. The oxidation of methanol and some kinetic parameters were investigated in KOH solution. Cyclic voltammetry was used for the electrochemical measurements. Kinetic parameters of the methanol oxidation were determined at different temperatures, scan rates, and concentrations of methanol. The surface morphologies …

Silicon Nanostructures For High Capacity Anodes In Lithium Ion Batteries, Tyler M. Selden

Theses and Dissertations

In this study we looked at several different silicon nanostructures grown for the purpose of optimizing anodes for lithium ion batteries. We primarily focused on two distinct types of structures, nanospirals, and Rugate structures. The samples were designed to have the mechanical robustness to endure the massive expansion caused by lithiation of silicon. All of the samples were grown using an electron beam evaporator. Scanning electron microscope images show that we have achieved the desired structural growth. The spirals were shown to have an average diameter of 343 nm on polished copper, and 366 nm on unpolished copper. The Rugate …

Effecting Of Dissolved Oxygen On Microbial Fuel Cells Based On Pseudomonas Aeruginosa, Chang-Li Cao, Li-Xiang Chen, Ran-Ran Wu, Ken-Lin Chang, Feng Zhao

Journal of Electrochemistry

In this work, the reaction between the electron shuttle secreted by Pseudomonas aeruginosa and anode was studied by measuring cyclic voltammogram and open circuit potential. The effect of dissolved oxygen on the oxidation reaction of anode was explored. It was demonstrated that the reaction was a diffusion-controlled and reversible process. The anode was a little affected when the dissolved oxygen of inocula was low (0 ~ 1.6 mg·L^-1). The polarization curves showed that the current output of microbial fuel cells decreased 7% with the impact of dissolved oxygen.

Nanocomposites Of Silicon And Carbon Derived From Coal Tar Pitch: Cheap Anode Materials For Lithium-Ion Batteries With Long Cycle Life And Enhanced Capacity, Yun-Xiao Wang, Shulei Chou, Hua-Kun Liu, S X. Dou

Shi Xue Dou

From energy and environmental consideration, an industrial waste product, coal tar pitch (CTP), is used as the carbon source for Si/AC composite. We exploited a facile sintering method to largely scale up Si/amorphous carbon nanocomposite. The composites with 20 wt.% silicon with PVdF binder exhibited stable lithium storage ability for prolonged cycling. The composite anode delivered a capacity of 400.3 mAh g−1 with a high capacity retention of 71.3% after 1000 cycles. Various methods are used to investigate the reason for the outstanding cyclability. The results indicate that the silicon nanoparticles are wrapped by amorphous SiOx and AC in Si/AC …