Exercise Science Commons^™

Validation Of Machine Vision And Action Sport Cameras For 3d Motion Analysis Model Reconstruction, John David Johnson, Michael Hales, Randy Emert

Faculty and Research Publications

The study investigated the feasibility of using action sport cameras for motion analysis research. Data acquired from two different marker-based motion capture systems and six different camera combinations were analyzed for motion reconstruction accuracy. Two different calibration procedures were used to determine the influence on marker position reconstruction. Static and dynamic calibration mean merit score differences between the reference and experimental camera systems were 0.4 mm and 1.3 mm, respectively. Angular displacement difference between the reference and experimental camera systems range between 0.1 and 2.0 degrees. A systematic bias (− 0.54 to 0.19 degrees) was determined between the reference and …

A Comparison Of Ground Reaction Forces And Muscle Activity Of The Tsunami Bar® Against A Rigid Barbell During Back Squat Phases, John Carver Middleton

Theses and Dissertations

An Institutional Review Board (IRB)-approved study was conducted to investigate the effects of the Tsunami Bar® (TB), a flexible barbell, on ground reaction force (GRF) production and muscle activity in the quadricep, hamstring, and gluteal muscle groups during phases of the squat exercise and compare the effects to the effects to using a rigid barbell (RB). A two-by-two repeated measures Analysis of Variance (ANOVA) test was used to compare the results. Descriptive statistics showed significantly higher GRFs for the TB during the unweighting phase, significant differences in GRFs between speeds for each phase, significantly higher forces on average with the …

A Biomechanical Approach To Prevent Falls In Ergonomic Settings, Sachini Kodithuwakku Arachchige

Theses and Dissertations

Introduction: Fall-related injuries are exceptionally prevalent in occupational settings. While endangering the workers’ health, falls cause poor productivity and increased economic burden in the workplace. Hence, identifying these threats and training workers to achieve proper postural control is crucial. Purpose: Study 1: To investigate the ankle joint kinematics in unexpected and expected trip responses during single-tasking (ST), dual-tasking (DT), and triple-tasking (TT), before and after a physically fatiguing exercise. Study 2: To investigate the impact of virtual heights, DT, and training on static postural stability and cognitive processing. Methods: Study 1: Twenty collegiate volunteers (10 males and females, one left …

Low-Cost Prosthetic Feet For Underserved Populations: A Comparison Of Gait Analysis And Mechanical Stiffness, Kaleigh Renninger, Brevin Banks, Dustin A. Bruening

Library/Life Sciences Undergraduate Poster Competition 2022

• Lower limb loss is an ongoing cause of disability throughout the world.
• Despite advancements in prosthetic technologies, there are numerous underserved populations in need of effective low-cost prosthetic foot options.

Biomechanics Of Trail Running Performance: Quantification Of Spatio-Temporal Parameters By Using Low Cost Sensors In Ecological Conditions, Noé Perrotin, Nicolas Gardan, Arnaud Lesprillier, Clément Le Goff, Jean-Marc Seigneur, Ellie Abdi, Borja Sanudo, Redha Taiar

Publications

The recent popularity of trail running and the use of portable sensors capable of measuring many performance results have led to the growth of new fields in sports science experimentation. Trail running is a challenging sport; it usually involves running uphill, which is physically demanding and therefore requires adaptation to the running style. The main objectives of this study were initially to use three “low-cost” sensors. These low-cost sensors can be acquired by most sports practitioners or trainers. In the second step, measurements were taken in ecological conditions orderly to expose the runners to a real trail course. Furthermore, to …

Stationary Exercise Classification Using Imus And Deep Learning, Andrew M. Heroy, Zackary Gill, Samantha Sprague, David Stroud, John Santerre

SMU Data Science Review

In the current market, successful fitness tracking devices utilize heart rate and GPS to determine performance. These devices are useful, but don't extensively classify stationary exercise. This paper proposes a modern approach for tuning and investigating optimal neural network types on stationary exercises using Inertial Measurement Units (IMUs). Using three IMUs located on the ankle, waist, and wrist, data is collected to map the body as it moves during the stationary physical activity. A novel five-stage deep learning tuning system was written and deployed to classify user movement as one of three classes: air squats, jumping jacks, and kettlebell swings. …

Adaptive Paddle Board, Alexander Holthaus, Alexander Holthaus, Garrett Holmes, Garett Jones

Mechanical Engineering

This Final Design Review (FDR) document outlines the Adaptive Paddle Board senior project, done by four Mechanical Engineering Students at California Polytechnic State University and provides detail on the project and what the team has accomplished. The goal was to create a universally adaptive paddle board that can be used by the Central California Adaptive Sports Center for a wide range of persons with disabilities. This document highlights current research from patents and existing products, details regarding customer specifications, results from concept generation, the manufacturing and testing that went into the final design, and the process taken to get there. …

Volumetric Muscle Loss: The Role Of Physical Activity And Autologous Repair On Force Recovery And Signaling Pathways, Richard Perry

Graduate Theses and Dissertations

Volumetric muscle loss affects both military and civilian persons. The hallmark of this injury is incomplete muscle regeneration, excessive fibrosis, and chronic inflammatory signaling resulting in permanent functional loss. Since permanent functional loss drastically reduces quality of life, many studies have been conducted to improve force recovery. Current scientific literature considers a repair strategy of either devitalized scaffolds infused with growth factors or viable tissue plus activating factors to be the more promising interventions for optimal force recovery. PURPOSE The purpose of this study is to incorporate autologous repair and physical activity and observe the effects of muscle force recovery …

A Real-Time Wireless Sweat Rate Measurement System For Physical Activity Monitoring, Andrew Brueck, Tashfin Iftekhar, Alicja B. Stannard, Kumar Yelamarthi, Tolga Kaya

Exercise Science Faculty Publications

There has been significant research on the physiology of sweat in the past decade, with one of the main interests being the development of a real-time hydration monitor that utilizes sweat. The contents of sweat have been known for decades; sweat provides significant information on the physiological condition of the human body. However, it is important to know the sweat rate as well, as sweat rate alters the concentration of the sweat constituents, and ultimately affects the accuracy of hydration detection. Towards this goal, a calorimetric based flow-rate detection system was built and tested to determine sweat rate in real …

Microscale Investigation Of Thermo-Fluid Transport In The Transition Fil, Region Of An Evaporating Capillary Meniscus Using A Microgravity Environment, Kenneth D. Kihm, Jeffrey S. Allen, Kevin P. Hallinan, David M. Pratt

Kevin Hallinan

In order to enhance the fundamental understanding of thin film evaporation and thereby improve the critical design concept for two-phase heat transfer devices, microscale heat and mass transport is to be investigated for the transition film region using state-of-the-art optical diagnostic techniques. By utilizing a microgravity environment, the length scales of the transition film region can be extended sufficiently, from submicron to micron, to probe and measure the microscale transport fields which are affected by intermolecular forces. Extension of the thin film dimensions under microgravity will be achieved by using a conical evaporator made of a thin silicon substrate under …

Toward Translating Near-Infrared Spectroscopy Oxygen Saturation Data For The Non-Invasive Prediction Of Spatial And Temporal Hemodynamics During Exercise, Laura M. Ellwein, Margaret M. Samyn, Michael E. Danduran, Sheila M. Schindler-Ivens, Stacy Liebham, John F. Ladisa Jr.

Exercise Science Faculty Research and Publications

Image-based computational fluid dynamics (CFD) studies conducted at rest have shown that atherosclerotic plaque in the thoracic aorta (TA) correlates with adverse wall shear stress (WSS), but there is a paucity of such data under elevated flow conditions. We developed a pedaling exercise protocol to obtain phase contrast magnetic resonance imaging (PC-MRI) blood flow measurements in the TA and brachiocephalic arteries during three-tiered supine pedaling at 130, 150, and 170 % of resting heart rate (HR), and relate these measurements to non-invasive tissue oxygen saturation (StO₂) acquired by near-infrared spectroscopy (NIRS) while conducting the same protocol. Local quantification …

Effectiveness Of Group Kickboxing As A Means To Improve Gait And Balance In Individuals With Ms, Kurt Jackson, Kimberly Edginton Bigelow, Christina Cooper, Harold L. Merriman

Harold L. Merriman

In recent years, there has been a particular emphasis on identifying and delivering appropriate therapeutic interventions that address the significant balance and gait impairments that affect individuals with multiple sclerosis (MS). Group interventions implemented in community settings have been especially of interest, including tai chi classes. Recently, the authors conducted a preliminary study to examine whether group kick-boxing, which requires more vigorous movements, might be a feasible intervention. Initial findings showed promise and led the authors to pursue a more rigorous follow-up study, with the objective of determining whether a 5-week group kickboxing class improved clinical measures of balance and …

Biomechanical Investigation Of Elite Place-Kicking, Chase M. Pfeifer

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Many studies aim to understand the fundamentals of kicking commonly displayed by soccer players [4,6,10,16,17,18,24,25,28,29,30,34,36,38,40]. Of those studies, most are limited to a two-dimensional (2D) analysis using high-speed cameras for position tracking or utilizing electromyography to observe the activity of select muscles [4,6,18,25,29,36]. The few studies that investigate kicking using a three-dimensional (3D) model are limited in their position tracking capabilities and focus mainly on joint flexion potentials and foot speed.

This dissertation is a comprehensive biomechanical analysis (kinematic and EMG) of the field-goal place-kicking techniques of four elite kickers in American football. Data were compared and contrasted with ball …

Development Of A Muscle Model Parameter Calibration Method Via Passive Muscle Force Minimization, Allison Kinney, Benjamin J. Fregly

Mechanical and Aerospace Engineering Faculty Publications

Computational predictions of subject-specific muscle and knee joint contact forces during walking may improve individual rehabilitation treatment design. Such predictions depend directly on specified model parameter values. However, model parameters are difficult to measure non-invasively. Methods for muscle model parameter calibration have been developed previously. However, it is currently unknown how the musculoskeletal system chooses muscle model parameter values. Previous studies have hypothesized that muscles avoid injury during walking by generating little passive force and operating in the ascending region of the force-length curve. This hypothesis suggests that muscle model parameter values may be selected by the body to minimize …

Synergy-Based Two-Level Optimization For Predicting Knee Contact Forces During Walking, Gil Serrancolí, Allison Kinney, Josep M. Font-Llagunes, Benjamin J. Fregly

Mechanical and Aerospace Engineering Faculty Publications

Musculoskeletal models and optimization methods are combined to calculate muscle forces. Some model parameters cannot be experimentally measured due to the invasiveness, such as the muscle moment arms or the muscle and tendon lengths. Moreover, other parameters used in the optimization, such as the muscle synergy components, can be also unknown. The estimation of all these parameters needs to be validated to obtain physiologically consistent results. In this study, a two-step optimization problem was formulated to predict both muscle and knee contact forces of a subject wearing an instrumented knee prosthesis. In the outer level, muscle parameters were calibrated, whereas …

The Influence Of Neuromusculoskeletal Model Calibration Method On Predicted Knee Contact Forces During Walking, Gil Serrancolí, Allison Kinney, Benjamin J. Fregly, Josep M. Font-Llagunes

Mechanical and Aerospace Engineering Faculty Publications

This study explored the influence of three model calibration methods on predicted knee contact and leg muscle forces during walking. Static optimization was used to calculate muscle activations for all three methods. Approach A used muscle-tendon model parameter values (i.e., optimal muscle fiber lengths and tendon slack lengths) taken directly from literature. Approach B used a simple algorithm to calibrate muscle-tendon model parameter values such that each muscle operated within the ascending region of its normalized force-length curve. Approach C used a novel two-level optimization procedure to calibrate muscle-tendon, moment arm, and neural control model parameter values while simultaneously predicting …

A Multi-Directional Treadmill Training Program For Improving Gait, Balance, And Mobility In Individuals With Parkinson’S Disease: A Case Series, Kimberly Smith, Kurt Jackson, Kimberly Edginton Bigelow, Lloyd L. Laubach

Mechanical and Aerospace Engineering Faculty Publications

Treadmill training is a commonly used intervention for improving gait in people with Parkinson’s disease (PD). However, little is known about how treadmill training may also influence balance and other aspects of mobility.

The purpose of this case series was to explore the feasibility and possible benefits of multi-directional treadmill training for individuals with PD. Four participants (62.3 ± 6.5 yrs, Hoehn & Yahr 2-4) performed 8 weeks of treadmill training 3 times per week. Weeks 1-4 included forward walking only, while weeks 5-8 included forward and multi-directional walking. Participants were tested every 4 weeks on 4 separate occasions. Outcome …

Deltoid Moment Arms During Abduction: A Subject-Specific Musculoskeletal Modeling Study In Healthy Shoulders And Shoulders With Rtsa, David Walker, Allison Kinney, Aimee Struk, Benjamin J. Fregly, Thomas Wright, Scott Banks

Mechanical and Aerospace Engineering Faculty Publications

Reverse total shoulder arthroplasty (RTSA) is increasingly used in the United States since approval by the FDA in 2003. RTSA relieves pain and restores mobility in arthritic rotator cuff deficient shoulders. Though many advantages of RTSA have been demonstrated, there still are a variety of complications (implant loosening, shoulder impingement, infection, frozen shoulder) making apparent much still is to be learned how RTSA modifies normal shoulder function. The goal of this study was to assess how RTSA affects deltoid muscle moment generating capacity post-surgery using a subjectspecific computational model driven by in vivo kinematic data.

How Sensitive Is The Deltoid Moment Arm To Joint Center Changes With Rtsa?, David Walker, Allison Kinney, Aimee Struk, Benjamin J. Fregly, Thomas Wright, Scott Banks

Mechanical and Aerospace Engineering Faculty Publications

The goal of this study was to assess the sensitivity of the deltoid muscle moment arms as a function of joint configuration for an existing RTSA subject. High variations were found for all three deltoid components. Variation over the entire abduction arc was greatest in the anterior and lateral deltoid, while the posterior deltoid moment arm was mostly sensitive to joint center changes early in the abduction arc. Moment arm changes of 10-16mm represent a significant amount of the total deltoid moment arm. This means there is an opportunity to dramatically change the deltoid moments arms through surgical placement of …

A Novel Approach To Estimation Of Patient-Specific Muscle Strength, David Walker, Allison Kinney, Benjamin J. Fregly, Thomas Wright, Scott Banks

Mechanical and Aerospace Engineering Faculty Publications

Current modeling techniques have been used to model the Reverse Total Shoulder Arthroplasty (RTSA) to account for the geometric changes implemented after RTSA. Though these models have provided insight into the effects of geometric changes from RTSA these is still a limitation of understanding muscle function after RTSA on a patient-specific basis. The goal of this study sought to overcome this limitation by developing an approach to calibrate patient-specific muscle strength for an RTSA subject.

Formulation To Predict Lower Limb Muscle Forces During Gait, Gil Serrancolí, Jonathan P. Walter, Allison Kinney, A. Barjau, Benjamin J. Fregly, Josep M. Font-Llagunes

Mechanical and Aerospace Engineering Faculty Publications

The human body has more muscles than Degrees of Freedom (DoF), and that leads to indeterminacy in the muscle force calculation. This study proposes the formulation of an optimization problem to estimate the lower-limb muscle forces during a gait cycle of a patient wearing an instrumented knee prosthesis. The originality of that formulation consists of simulating muscle excitations in a physiological way while muscle parameters are calibrated. Two approaches have been considered. In Approach A, measured contact forces are applied to the model and all inverse dynamics loads are matched in order to get a physiological calibration of muscle parameters. …

Optimization Problem Formulation For Predicting Knee Muscle And Contact Forces During Gait, Gil Serrancolí, Jonathan P. Walter, Allison Kinney, Benjamin J. Fregly, Josep M. Font-Llagunes

Mechanical and Aerospace Engineering Faculty Publications

The human body has more muscles than degrees of freedom (DOF), which leads to indeterminacy in the muscle force calculation. In this study, an optimization problem to estimate the lower-limb muscle forces during a gait cycle of a patient wearing an instrumented knee prosthesis is formulated. It consists of simulating muscle excitations in a physiological way while muscle parameters are calibrated.

Changes In In Vivo Knee Contact Forces Through Gait Modification, Allison Kinney, Thor F. Besier, Amy Slider, Scott L. Delp, Darryl D. D'Lima, Benjamin J. Fregly

Mechanical and Aerospace Engineering Faculty Publications

Gait modification represents a non-invasive method for reducing knee joint loading in patients with knee osteoarthritis. Previous studies have shown that a variety of gait modifications are effective in reducing the external knee adduction moment. The external knee adduction moment is often used as a surrogate measure of medial compartment force. However, a recent study showed that reductions in the external knee adduction moment do not guarantee reductions in medial compartment loads. Therefore, direct measurement of changes in knee contact force is important for determining the effectiveness of gait modifications. A previous study found that medial thrust gait and walking …

Throwing Frame For Athletes With Dissabilities, Andrew Higgins, Stefan Owechko, Gabriel (Gabe) Terrasas, Kevin Crisfield

Mechanical Engineering

Team Zeus’ senior project was to design, build and test a working throwing frame system for Bridge II Sports, a nonprofit organization in North Carolina. The throwing frame is used to allow athletes and individuals with disabilities to throw shot-put, discus, and javelin using a frame to sit against. Team Zeus was specifically tasked to build a frame that is lighter weight and more transportable than products that are currently on the market. This frame also is adjustable to accommodate a wide range of athlete weights, sizes, and abilities. The final result is a 35lb aluminum frame with two different …

Effectiveness Of Group Kickboxing As A Means To Improve Gait And Balance In Individuals With Ms, Kurt Jackson, Kimberly Edginton Bigelow, Christina Cooper, Harold L. Merriman

Mechanical and Aerospace Engineering Faculty Publications

In recent years, there has been a particular emphasis on identifying and delivering appropriate therapeutic interventions that address the significant balance and gait impairments that affect individuals with multiple sclerosis (MS). Group interventions implemented in community settings have been especially of interest, including tai chi classes. Recently, the authors conducted a preliminary study to examine whether group kick-boxing, which requires more vigorous movements, might be a feasible intervention. Initial findings showed promise and led the authors to pursue a more rigorous follow-up study, with the objective of determining whether a 5-week group kickboxing class improved clinical measures of balance and …

Interview With Adam Boesel, Green Micro Gym, 2011 (Audio), Adam Boesel

All Sustainability History Project Oral Histories

Interview of Adam Boesel by Teresa Celestine at Green Micro Gym Portland, Oregon on July 29th, 2011.

The interview index is available for download.

Muscle Contributions To Frontal And Transverse Plane Whole-Body Angular Momentum, Richard R. Neptune, Craig P. Mcgowan, Allison Kinney

Mechanical and Aerospace Engineering Faculty Publications

The purpose of this study was to build upon previous work by analyzing how gravity and individual muscles contribute to frontal and traverse plane whole-body angular momentum. Identifying which muscles are responsible for generating angular momentum has important implications for the diagnosis and treatment of movement disorders.

Pre-Swing Deficits In Forward Propulsion, Swing Initiation And Power Generation By Individual Muscles In Hemiparetic Walking, Carrie L. Peterson, Allison Kinney, Steven A. Kautz, Richard R. Neptune

Mechanical and Aerospace Engineering Faculty Publications

Clinical studies of hemiparetic walking have shown pre-swing abnormalities in the paretic leg suggesting that paretic muscle contributions to important biomechanical walking subtasks are different than those of non-disabled individuals. Three-dimensional forward dynamics simulations of two representative hemiparetic subjects with different levels of walking function classified by self-selected walking speed (i.e., limited community=0.4–0.8 m/s and community walkers=>0.8 m/s) and a speed-matched control were generated to quantify individual muscle contributions to forward propulsion, swing initiation and power generation during the pre-swing phase (i.e., double support phase proceeding toe-off). Simulation analyses identified decreased paretic soleus and gastrocnemius contributions to forward propulsion …

Relationships Between Muscle Contributions To Walking Subtasks And Functional Walking Status In Persons With Post-Stroke Hemiparesis, Allison Kinney, Carrie L. Peterson, Steven A. Kautz, Richard R. Neptune

Mechanical and Aerospace Engineering Faculty Publications

Walking speed is commonly used to predict stroke severity and assess functional walking status (i.e., household, limited community and community walking status) post-stroke. The underlying mechanisms that limit walking speed (and functional walking status by extension) need to be understood to improve post-stroke rehabilitation. Previous experimental studies have shown correlations between paretic plantarflexor output during the pre-swing phase and walking speed and suggest that the paretic hip flexors can compensate in some hemiparetic subjects. Modeling and simulation studies of healthy walking have shown that the ankle plantarflexors, soleus (SOL) and gastrocnemius (GAS), and uniarticular hip flexors (IL) are essential contributors …

Development And Analysis Of A Software Package To Quantify In Vivo Polyethylene Wear After Total Hip Arthroplasty, Allison Kinney, Catherine G. Ambrose

Mechanical and Aerospace Engineering Faculty Publications

Since the first total hip arthroplasty (THA) in 1938, THA evolved and developed into one of the major concentrations of orthopaedic research. The typical hip implant device used today incorporates a femoral and an acetabular component that serve to replicate the anatomical and mechanical functions of the natural hip joint. However, several problems exist that can effect the function of the implant device. Wear in the polyethylene liner of the acetabular component of the total hip replacement device is known as one of the major factors that affects the longevity of total hip replacement devices. Both manual and computer-aided techniques …