Forest Sciences Commons^™

Barriers To Use Of Cross-Laminated Timber In Maine, Shane R. O'Neill

Forest Resources Faculty Scholarship

To increase understanding of both the adoption rate and in-state manufacturing of mass timber In Maine, the 131^st Legislature and Governor Mills passed LD 881, a resolve directing a study of the barriers facing cross-laminated timber In Maine and provide recommendations to promote their use in construction. This study was developed in response to the resolve. The study engaged 108 unique participants to define available training, education, and experiences across the stakeholders throughout the building lifecycle process in the state.

From this information, the following five recommendations are proposed:

1. Understand the policies and initiatives of other states to develop …

Development Of Preservative-Treated Cross-Laminated Timber And Lignin-Reinforced Polyurethane-Adhesive For Glued Laminated Timber, Samuel Oluwafemi Ayanleye

Theses and Dissertations

Interest in the use of mass timber in building and construction is growing worldwide, this is due to the structural integrity and reduced environmental footprint of timber-based structures. Concerns associated with the biological and environmental degradation of mass timber necessitate the development of adequate protection strategies to ensure the durability of these products. Preservative treatment is a proven technique that increases the durability and performance of wood in-service and can also be applied to large-sized timber panels such as cross-laminated timber (CLT). Therefore, this study focused on investigating the feasibility of treating prefabricated 3- and 5-layer CLT panels with Copper-azole …

Out Of The Wood: Sojurn Cyclery, Jay H. Kinsinger

Engineering and Computer Science Faculty Contributions to the Popular Press

No abstract provided.

Contact Dewatering Of Cellulose Nanofibers For Biopolymer Composite Applications, Alexander Collins

Electronic Theses and Dissertations

Cellulose Nanofibrils (CNFs) are promising materials for reinforcement of polymer matrices attributable to their impressive physical and mechanical properties, as well as their biodegradability. However, the utilization of these materials in composites is made challenging by the water content of CNF slurries, the tendency of CNFs to agglomerate as they dry, and incompatibility between hydrophilic CNFs and hydrophobic polymer matrices. The most commercially viable drying methods to produce small-scale dry CNFs, such as spray drying, are very energy intensive, can only dry the materials down to micron-scale agglomerates, and do not preserve fibrillar aspect ratios. “Contact dewatering,” or the removal …

Comparative Life Cycle Assessment Of Embodied Carbon And Operational Energy Of Different Building Systems, Marilia Hellmeister

Electronic Theses and Dissertations

Due to human activity, the levels of carbon emissions found in the atmosphere have reached its highest concentration and therefore it is necessary to find solutions to reduce, mitigate and adapt to a more sustainable pattern of development. The substitution of fossil fuel-dependent materials with renewable materials which exhibit lower embodied carbon is an option to be considered in the design phase of a building. Engineered wood product innovations over the past twenty years, coupled with design innovation and building code modifications have demonstrated their viability in multi-story construction (18 stories). The goals of this project are to 1) estimate …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

Yield And Mechanical Properties Of Veneer From Maine-Grown Eastern Spruce And Balsam Fir, Marshal Bertrand

Electronic Theses and Dissertations

This research focused on the utilization of Maine Eastern spruce and balsam fir for veneer production. Maine currently has no manufacturers of or products using structural veneer. The diversification of markets for Maine’s softwoods has been identified as a route to increase the resilience of the forest-based economy. Veneer production technology has improved significantly since the last look at Maine spruce veneer (1969), justifying the reinvestigation of Maine spruce-fir veneer. The objective of this research was to provide information on the yield of processing veneer and the quality of said veneer. A sample size of 37 Eastern spruce and 38 …

The Effect Of Green Biobased Binder On Structural, Mechanical, Liquid Absorption And Wetting Properties Of Coated Papers, Bilge N. Altay, Charles Klass, Ting Chen, Alexandar Fleck, Cem Aydemir, Arif Karademir, Paul D. Fleming

Articles

Synthetic styrene-butadiene (SB) and styrene-acrylic (SA) latex binders used in paper coating formulations are common and based on unsustainable petroleum sources. Today's papermaking industry turns towards sustainable substitutes that do not compromise quality, and reduce carbon emission, toxic substance release and waste disposal concerns related to fossil fuel sources. In this study, colloidal starch-based latex nanoparticles that do not require cooking were used for pigment coating and coated on the paper surfaces. The effects of these new biobased binders on the structural and mechanical strength properties, liquid absorption, wetting and surface topography of the paper were investigated and compared with …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …

Cellulose Based Separator For High-Performance Lithium-Ion Batteries, Akshit Vaidya

Masters Theses

During the past two decades, lithium-ion batteries (LIBs) have gained great success in the field of portable devices, and currently, are penetrating to the market of vehicles. Compared to the fast development of LIBs, little efforts have been dedicated to the separator, which is one of the most important components of LIBs. Primarily, the lithium-ion battery separator has two functions, one is to prevent direct contact between the positive and negative electrodes, and the other is to provide a path for effective ionic transportation. Currently, the separator market of LIBs is dominated by polyolefin materials such as polypropylene, polyethylene, and …

Impact Of Substrate And Process On The Electrical Performance Of Screen-Printed Nickel Electrodes: Fundamental Mechanism Of Ink Film Roughness, Bilge N. Altay, Jerome Jourdan, Vikram S. Turkani, Hervé Dietsch, Dinesh Maddipatla, Alexandra Pekarovicova, Paul D. Fleming, Massood Atashbar

Bilge Nazli Altay

Fate Of Conductive Ink Pigments During Recycling And Landfill Deposition Of Paper-Based Printed Electronics, James Edward Atkinson

Dissertations

Printed electronics (PE) are being developed as an alternative to traditional electronics, due to the more efficient use of materials and lower cost of production. The overall goal of this study was to understand how metallic pigments in conductive inks in PE are partitioned during landfill disposal and paper recycling conditions. The purpose is to assess the potential environmental impacts of PE landfilling in terms of metal leaching and to help develop new strategies for sequestering metallic ink components while paper-based PE are subjected to conventional paper recycling methods. The objective of this research is to study the fate of …

Lignin Maximization: Analyzing The Impact Of Different Feedstocks And Feedstock Ratios Using Organosolv Fractionation, Marc Banholzer

Masters Theses

Over-exploitation of fossil fuels coupled with increasing pressure to reduce carbon emissions are prompting a transition from conventional petrochemical feedstocks to sustainable and renewable sourced carbon. The use of lignocellulosic biomass as a feedstock for integrated biorefining is of current high interest, as separation into its component parts affords process streams of cellulose, hemicellulose and lignin, each of which can serve as a starting point for the production of biobased chemicals and fuels. Given the large number of potential sources of lignocellulosic feedstocks, the biorefinery will need to adapt to the supplies available over a normal growing season. Of particular …

Development Of Eco-Friendly Composite Foam Boards For Thermal Insulation And Packaging Purposes Using Cellulose Nanofibrils (Cnf), Nadir Yildirim

Electronic Theses and Dissertations

Reducing energy consumption is a high priority in the United States and throughout the world. Energy used to heat and cool occupied constructed facilities is of particular concern, and one of the most effective strategies is insulating the building envelope. Historically, builders used whatever material was available to fill the void between interior and exterior walls, including wool fibers, paper, and even corn cobs. Today, homes are built using foam insulation that harden when applied, blown-in loose insulation, fiberglass mats or rigid foam boards usually composed of polystyrene. Rigid foam boards are used in a variety of applications despite the …

Nanoscaled Cellulose And Its Carbonaceous Material: Application And Local Structure Investigation, Yujie Meng

Doctoral Dissertations

In this dissertation, cellulose nanocrystals three-dimensional morphology, size distribution, and the crystal structure were statistically and quantitatively investigated. Lognormal distribution was identified as the most likely for cellulose nanocrystals’ size distribution. Height and width dimensions were shown to decrease toward the ends from the midpoint of individual CNCs, implying a spindle-like shape. XRD analysis of crystallite size accompanied with TEM and AFM measurements revealed that the cross-sectional dimensions of individual switchgrass CNC were either rectangular or elliptical shape, with an approximately 3~5 nm [nanometer] lateral element length range. A sponge-like carbon aerogel from microfibril cellulose with high porosity, ultra-low density, …

Production And Applications Of Formaldehyde-Free Phenolic Resins Using 5-Hydroxymethylfurfural Derived From Glucose In-Situ, Yongsheng Zhang

Electronic Thesis and Dissertation Repository

The phenol-formaldehyde (PF) resin manufacturing industry is facing a growing challenge with respect to concerns over human health, due to the use of carcinogenic formaldehyde and sustainability due to the use of petroleum-based phenol in PF resin manufacture. Glucose and its derivative, 5-hydroxymethylfurfural (5-HMF), have proven to be potential substitutes for formaldehyde in the synthesis of phenolic novolac resins.

This thesis investigated a number of glucose and 5-HMF resin systems including the curing of phenol-glucose novolac resin (PG) with a bis-phenol-A type epoxy. The curing process was modeled according to the Sestak-Berggren equation (S, B) using Málek methods. This was …

Investigating Wood Welding Parameters Using A Prototype Welding Machine, Timothy R. Melin

Master's Theses

Understanding how different processing variables influence wood welded bonds is vital if the technique will ever be used to create engineered lumber without using adhesives. A variation of vibration welding, wood welding uses pressure and friction to bond materials together. During welding, heat causes a softening in the wood, a naturally occurring composite material. This softening leads to fiber entanglement and a bond forms upon cooling.

The goal of this research was to investigate several processing aspects of the wood welding procedure. A prototype wood welding machine, designed and fabricated from the ground up, was used to investigate the effects …

Investing In Maine Research Infrastructure: Sustainable Forest Bioproducts, Michael Eckardt, Stephen Shaler, Hemant P. Pendse, Adriaan R. P. Van Heiningen, Robert G. Wagner

University of Maine Office of Research Administration: Grant Reports

The University of Maine, the University of Southern Maine, several baccalaureate institutions in the state, along with other federal, state and local public, private, and non-profit institutions will collaborate to create the Forest Bioproducts Research Institute (FBRI) at the University of Maine. The vision of the FBRI is to advance understanding about the scientific underpinnings, system behavior, and policy implications for the production of forest-based bioproducts that meet societal needs for materials, chemicals, and fuels in an economically and ecologically sustainable manner.

The research plans Integrate three themes. They are (1) forest sustainability modeling of life cycle assessment, (2) integrated …

Development And Commercialization Of Advanced Wood-Based Composites In Maine, Habib J. Dagher

University of Maine Office of Research Administration: Grant Reports

This award is to the University of Maine to support the activity described below for 36 months. The proposal was submitted in response to the Partnerships for Innovation Program Solicitation (NSF 0179).

Partners
The partners for the award include the University of Maine (Lead Institution), Maine Technology Institute, Eastern Maine Development Corporation, State Department of Economic and Community Development, The Manufacturing Extension Partnership, Maine Department of Transportation, Louisiana Pacific, Dow Chemical, State Farm Insurance, Henderson and Bodwell, The Kenway Corporation, Market Development Alliance of the FRP Composites Industry, APA the Engineered Wood Association, National Institutes of Standards and Technology, USDA …

Research On Advanced Technologies For Housing: Optimized Frp-Reinforced Osb Panels For Disaster-Resistant Construction, William S. Davids

University of Maine Office of Research Administration: Grant Reports

The satisfactory performance of wood-framed housing in a seismic or wind event requires a sufficiently strong, ductile, and energy-absorbing lateral force-resisting system. This project will focus on the development of optimized synthetic fiber-reinforced OSB panels to improve the disaster resistance of conventional wood-frame construction. The project research will employ response simulation, small-scale connection and durability testing, and full-scale shear wall testing. Various fiber-reinforced polymer (FRP) systems will be investigated for reinforcing the OSB panels. Shear tests of individual nailed connections between FRP-reinforced and plain OSB panels and lumber framing will be conducted to determine monotonic and cyclic fastener load-slip relationships. …

Development Of Water-Based Ink System For Braille Printing, Saurabh Varma

Masters Theses

The most commonly used system of writing by and for blind persons is called Braille, named after its French inventor, Louis Braille (1809-1952). Braille is comprised of a rectangular six-dot cell on its end, with up to 63 possible combinations using one or more of the six dots. Braille is the only reliable method of literacy for blind persons, because it enables them to read and write by touch¹.

Currently, Braille is printed by special embossers that serve as a printing press. These embossers create Braille output when it is attached appropriately to computers. The speed of these …

Lateral Migration Of A Solid Particle In Shear Flow, Wutthapong Jiraporncharoen

Masters Theses

Lateral migration of solid particles in shear flow is observed in various industrial applications. Suspensions in a blade coater, a device used to apply coating pigment to a base paper to improve paper properties, is an example. Particle hydrodynamics will affect the quality of coated paper and runnability of the coater especially when the speed of the coating machine is very high or the pigment concentration is increased.

Many factors will affect the particle migration. The wall repulsion or lubrication effect forces the particle away from a wall to the channel center. The inertial effects are increased by increasing the …

Effect Of Poly Acrylate Addition On Coating Color Rheology, Water Retention And Coating Performance, Shambhu Nath

Masters Theses

Five polyacrylate samples were used to study their effects on coating color rheology, water holding and runnability. The Cylindrical Laboratory Coater was used to apply the coatings and study the runnability of the coating colors. The healing tendencies of the coatings were studied by inducing a scratch under the blade. The higher acid level and degree of crosslinking of the polyacrylate gave higher viscosity and the higher acid level also gave higher water retention. Coating colors containing polyacrylates were less prone to dilatancy at high shear. The addition of polyacrylate reduced the healing of coating colors, but for the same …

Microencapsulation As An Alternative To Emulsification For Preparing As A For Use In Papermaking, William J. Corriveau

Masters Theses

The sizing chemical ASA is emulsified to make i t compatible with the papermaking process. Unfortunately, emulsified ASA is chemically reactive with water at the elevated temperatures found in papermaking systems. As an alternative, encapsulated ASA was made and investigated for its stability towards water at elevated temperatures.

A handsheet procedure was developed to analyze emulsified and encapsulated ASA. It was concluded that the procedure gave statistically reproducible results. Investigations with the procedure revealed important variables concerning the laboratory and m ill application of ASA. Evidence indicated that retention of ASA was critical to sizing development.

Encapsulated ASA made for …

Dickey-Lincoln School Lakes Project Environmental Impact Statement: Appendix G: Recreation Resources (Revised June 1978), U.S. Army, Corps Of Engineers, New England Division, Northern Maine Regional Planning Commission, Land Use Consultants, Inc.

Dickey-Lincoln School Lakes Project

The purpose of this report is to evaluate and describe the existing recreational use and resources of the project area and the encompassing study area and to project the future use of those resources both with and without the Dickey-Lincoln School Lakes Project. The primary impact area of the proposed project (project area) includes the St. John River watershed upstream of the proposed damsites to the confluence of Nine-mile Brook. The area is bounded by the watershed divide with the Allagash River on the east and the Canadian Border on the west. Major tributaries of the St. John affected by …

Terrestrial Ecology Of The Dickey-Lincoln School Lakes Project, Corps Of Engineers, New England Division, Environmental Research & Technology, Inc

Dickey-Lincoln School Lakes Project

This introduction of the St. John River watershed is situated in a transitional zone between the Boreal Forest Formation and the Eastern Deciduous Forest Formation. Second-growth forests representative of these two ecosystems cover extensive areas of the project site. The boreal forest forms a broad transcontinental belt in northern North America and Eurasia, with southern montane extensions. This northern forest is characterized by evergreen, coniferous trees, predominately spruce-fir The eastern deciduous forest, composed of broad-leaved hardwoods, extends throughout the eastern United States except Florida (Dasmann, 1968; Oosting, 1956).