Risk Analysis Commons^™

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Safety Evaluation Of Hawaii Dot Modified Type A-1 Flared Buried In Backslope Guardrail End Terminal, Sina Changizian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Hawaii Department of Transportation (HDOT) desired to evaluate the crashworthiness of a guardrail end terminal design in which the upstream guardrail anchorage was connected to a block partially buried in a cut slope, known as a “Buried in Backslope” or BIB design. The HDOT BIB system used an upper W-beam with 8-in. deep blockouts attached to W6x9 steel posts and a lower W-beam rubrail located 3 in. below the upper rail. The system used two horizontal flares: 7.4:1 near the upstream anchor block and a 13:1 flare through the ditch.

Critical impact points (CIPs) were identified and recommended for …

Transitioning To A Lower Global Warming Refrigerant, A Performance Study Of R-513a And Hfc-134a In Commercial Chillers, Hossein Abedsoltan, Mark B. Shiflett

Chemical and Biochemical Engineering Faculty Research & Creative Works

The performance of R-513A and HFC-134a refrigerants is compared in two identical chillers operating at the University of Kansas. R-513A is a more environmentally friendly refrigerant due to its lower global warming potential that can be used as a retrofit replacement for HFC-134a in chillers. This study investigates the performance comparison of transitioning from HFC-134a to R-513A. The chillers have been in operation for two years, and cooling capacity, coefficient of performance, and other operating parameters are compared under similar cooling conditions. Cooling capacities ranged from 100 to 500 kW for both chillers. Overall, the energy consumption and coefficient of …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Pipeline Risk Analysis Optimization With Monte Carlo Method Using Gamma Distribution, Farhan Rama Digita, Jaka Fajar Fatriansyah, Abdul Rahim Ridzuan, Hanna Ovelia, Imam Abdillah Mas'ud, Irma Hartia Tihara, Baiq Diffa Pakarti Linuwih

Journal of Materials Exploration and Findings

The inspection process of piping components in the oil and gas industry is one of the most crucial things, given the high risk posed by pipeline system failures, which have a huge impact on losses, both from environmental and financial aspects. Risk-based inspection with the Monte Carlo method is one of the efforts that can be made to minimize failures in piping systems, by involving data distribution to calculate the probability of component failure. Although the normal distribution is commonly used for generating random variables, its use in corrosion rate calculation can lead to overestimation due to negative corrosion rate …

A Review On Ship Recycling Industry In Bangladesh From Global Perspective, Ahammad Abdullah, Zobair Ibn Awal, M Ziauddin Alamgir, Md. Jobayer Mia, Farihatul Mim, Utpal K. Dhar

Journal of Ocean and Coastal Economics

At present, the global center of the ship breaking and recycling industry is in South Asia, specifically Bangladesh, India, and Pakistan. These three countries account for 70–80 percent of the international recycling market for ocean-going vessels, with China and Turkey covering most of the remaining market. Only about 5 percent of global volume is scrapped outside these five countries. Bangladesh has environmentally beneficial coastal region and affordable labor that make the shipbreaking and recycling business as a potential sector for the country. In addition, ship recycling and its related businesses are helping to solve our nation’s unemployment issues at all …

Integrating Sensor Development, Risk Assessment, And Community Engagement To Support Environmental Justice In The Rural Community Of El Tiple, Colombia, David Bahamon Pinzon

All Dissertations

In Colombia, ethnic communities have traditionally been responsible stewards of natural resources. They recognize the importance of these resources for their livelihood, as well as their ancestral and cultural heritage. El Tiple, a rural Afro-Colombian community, has been affected by the incursion of private corporations that promoted the expansion of sugarcane monocrops in their territory. Since the introduction of the monoculture industry, local freshwater sources have been depleted due to intensive water use for irrigation of the sugarcane crops. Additionally, the intensive usage of agrochemicals has been linked with loss of native flora, damages to family farms, and pollution of …

Integrating Steel Slag Aggregates Into Asphalt Paving By Harmonizing Availability, Quality, Economics, And The Environment, Timothy R. Murphy

Theses and Dissertations

This thesis provides guidance on how to balance matters related to the environmental stewardship, market sources, origin and uses, material properties, performance, and economic impact of using slag materials in pavements. The literature on this topic provides numerous references on the use of slag materials for specific applications, and this thesis aims to make use of those references along with other data from the author to describe slag materials from a holistic perspective and provide some suggestions for balancing several factors that impact optimal use of this resource within pavement structures. Discussion is given to the increased importance of recycling …

Multi-Mode Total Focusing Method (Mtfm) To Detect High-Temperature Hydrogen Attack (Htha) – A Review, Anjar Oktikawati, Rini Riastuti, Nursidi Yuanto

Journal of Materials Exploration and Findings

High temperature hydrogen attack (HTHA) is a commonly observed harm component in carbon steels exposed to high temperature and pressure in a hydrogen-rich environment. Hydrogen together with carbon responds to produce methane. The formation of methane bubbles in steel can lead to loss of fracture toughness and lead to intergranular cracking. The main challenge of this problem lies in early warning systems that can detect these bubble clusters before they reach the advanced stage. Several advanced ultrasonic inspections have been developed over the years due to the challenges of inspecting materials for defects and discontinuities. These cover time-of-flight diffraction (ToFD), …

Development Of Dynamic Risk-Based Inspection Using Forward Difference Approach For Pipe Failure Due To Uniform Corrosion, Jaka Fajar Fatriansyah, Zahra Nadia Nurullia, Andreas Federico, Dedi Priadi

Journal of Materials Exploration and Findings

The oil and gas industry is one of the world's largest and most influential energy contributors. All aspects involved in the operation of this industry are fundamental to be reviewed and managed correctly, especially by preventing or minimizing the failures that could occur. Uniform corrosion is the most common component failure mechanism that can cause failure in the oil and gas industry. The company's actions in managing and preventing the risk of this type of failure have a major role in the sustainability of the company due to the possibility of more significant impacts if the risk cannot be handled …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Structural Integrity Analysis Of The Rig Mast Following Repair Of Two Diagonal Braces In The Upper Mast Section, Rendhatya Padmodwiputra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Bambang Eka Satria, Chandra Arif, Eka Juni Suarthana

Journal of Materials Exploration and Findings

During a move to the new drilling location, two braces of the upper mast section on a 550 HP oil and gas rig was damaged. When damage is discovered, the rig operating company should conduct a risk analysis related to the damage using the standard used to determine rejection criteria and follow-up repairs. The strength of the rig mast is calculated using Finite Element Analysis (FEA) with initial conditions (before damage occurs) where all braces are installed and extreme conditions where neither brace is repaired. The calculation results are then used to assess the risk of reducing the rig mast …

Structural Risk-Based Underwater Inspection (Rbui) As A Cost Reduction Of Field’S End Of Production Life, Ivan Fitrian Putra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Yuki Haidir, Faisal Dwiyana Purnawarman, Iwan Sukirna, Widi Hernowo

Journal of Materials Exploration and Findings

Mubadala Petroleum operates offshore platforms in a southern Makassar Straits that needs to be periodically inspected. The cost for the inspection is massive due to the high cost of mobilization and demobilization of vessels including crew and equipment. In response of a new approach to reduce cost, a Risk-Based Underwater Inspection (RBUI) methodology is developed. This RBUI purpose is to reduce the inspection interval of the offshore platform, from every 2 years to a longer period^[1]. There are existing RBUI methodologies, which are already developed and implemented in other companies^[5]. Purpose of this paper is to …

Dynamic Rbi With Central Difference Method Approach In Calculation Of Uniform Corrosion Rate: A Casestudy On Gas Pipelines, M.Riefqi Dwi Alviansyah, Fernanda Hartoyo, Zahra Nadia Nurullia, Ari Kurniawan

Journal of Materials Exploration and Findings

The oil and gas industry generally uses a piping system to drain fluids. Even though the pipes used have been well designed, the use of pipes as a means of fluid transportation still provides the possibility of failure that can occur at any time, one of which is due to uniform corrosion. The use of standard Risk Based Inspection (RBI) according to the API RBI 581 document has been widely used to anticipate potential failures to pipe components. The use of standard RBI can reduce the risk of failure significantly. Because the standard RBI considers the component risk value to …

Contents, Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

Preface Of Volume 1 Issue 1 On Journal Of Materials Exploration And Findings (Jmef), Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

The Optimization Of Failure Risk Estimation On The Uniform Corrosion Rate With A Non-Linear Function, Fernanda Hartoyo, Jaka Fajar Fatriansyah, Imam Abdillah Mas'ud, Farhan Rama Digita, Hanna Ovelia, D. Rizal Asral

Journal of Materials Exploration and Findings

Failures in the oil and gas pipeline system are conditions that must be avoided and anticipated because the losses due to the failures can occur at a very high level. Internal corrosion is one of the significant causes of the failures in pipeline systems. In addition, this type of corrosion is due to the high content of carbon dioxide and other corrosive substances in crude oil and natural gas. Therefore, an optimal inspection scheduling system is required to prevent the possibility of pipeline failures due to corrosion and to avoid any overspending on the budget due to excessive inspection scheduling. …

Material Selection Of Below-Knee Leg Prosthetics, Raihan Kenji Rizqillah

Journal of Materials Exploration and Findings

The effort to select the best pylon material, part of below-knee leg prosthetic, has been performed. It begins with function analysis to generate design requirement, which concludes that the objective is to select material that gives proper mechanical properties with lowest weigth and cost. Constraint requirements eliminate unsuitable material. Material indices, a scoring function, are derived from objective with respect to a function, and used for ranking material candidates. Ranking from material indices gives top material candidates of woods. Al alloy, Mg alloy, and ferrous alloy. Further seek of documentation is undertaken by failure analysis, value analysis, fabrication, and environmental …

Vêtements De Protection Chimique Contre Les Aérosols Solides : Performances Des Matériaux Sous Différentes Conditions D'Exposition Et Caractérisation Des Déterminants, Ludovic Tuduri, Loïc Wingert, Yves Cloutier, Stéphane Hallé, Jean Luc Giraudel, Ali Bahloul, Dominic Tessier, Patricia Dolez

Rapports de recherche scientifique

Historiquement, les mesures jugées prioritaires en hygiène industrielle ont été orientées vers la prévention de l’exposition par les voies respiratoires. Des centaines de valeurs limites d’exposition ont ainsi pu être établies à partir de méthodes d’évaluation quantitative du risque.

La part de l'exposition cutanée dans l’exposition professionnelle aux substances toxiques est pourtant significative. Le National Institute for Occupational Safety and Health (NIOSH) estime à 13 millions le nombre de travailleurs exposés à des produits chimiques par la peau avec des coûts annuels induits par le traitement des troubles cutanés évalués à un milliard de dollars. Il n’existe pas de données …

Time-Dependent Reliability Framework For Durability Design Of Frp Composites, Rajneesh Kumar Bharil

Graduate Theses, Dissertations, and Problem Reports (ETD)

The life-cycle performance, durability, and aging characteristics of Fiber Reinforced Polymer (FRP or Structural Composites) have been of keen interest to the engineers engaged in the FRP design, construction, and manufacturing. Unlike conventional construction materials such as steel and concrete, the design guidelines to account for the aging of FRP are somewhat scattered or not available in an approved or consistent format. Loss of strength over time or aging of any structural material should be of concern to engineers as the in-service lifespan of many engineering structures is expected to exceed 100 years. Use of durability strength-reduction factors or factors …

Latex Modified Concrete - Very Early Strength, Bobby Steele

Purdue Road School

INDOT came out with specifications for a very early strength concrete to use on bridge deck overlays. This concrete is fast setting, which allows overlays to be performed over a weekend and benefits the traveling public with a short duration of traffic interference. Cure time to reach the strength requirement is 3 hours. E&B Paving performed the first application with the new spec on August 26, 2018. Many changes were also made to the INDOT Specification Section 722.

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Next Generation Protocol: Innovating A Resilient Future, Andrew Steven Rudnick, Jamie Cannady, Joe Decesaro, Juan A. Ortiz Salazar

Materials Engineering

Conventional practices do not account for product life beyond end-of-sale – these practices are not sustainable. We have developed an end-of-life protocol that includes a metric that we call the Recovery Rating. The objectives of this Next Generation Protocol, beyond supporting the United Nations’ Sustainable Development Goals, are to encourage the production of goods designed for recovery and to promote the collaboration between consumers, the public, and the private sector to recover goods at their end-of-life. The Recovery Rating that we propose evaluates and quantifies recovery potential of products. The Recovery Rating, which is normed against embodied energy from the …

Comparison Of Intrusive And Non-Intrusive Methods For Corrosion Monitoring Of Fuel Processing Systems, Armando Jacob Espinoza, Thomas Conner Field

Materials Engineering

This presentation contains an assessment of the best overall corrosion monitoring device, intrusive or non-intrusive, for use in the petrochemical industry. Corrosion in the petrochemical industry is a large issue because it causes a deterioration of pipe integrity in fuel processing systems. A reduction of pipe wall integrity due to corrosion could result in a leak or an explosion of fuel processing lines since those systems function at high pressures. The use of corrosion monitoring systems in the petrochemical industry helps to detect early signs of corrosion prior to failure so that proper maintenance can be performed to prevent catastrophe. …

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …

Numerical Modeling And Seismic Assessment Of Smart Isolation System For High-Speed Railway Rc Bridge Subjected To Near-Field Ground Motions, Lingkun Chen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Late Morning Concurrent Sessions: Innovations In Aviation Technologies: Presentation: Relative Material Loss: A Methodology For Assessing Island Airport Steel Marine Bulkheads, Robert Ernsting, Constantine M. Koursaris

Aviation / Aeronautics / Aerospace International Research Conference

A July 2015 report from the Airports Council International – North America (ACI-NA) states “U.S. airports are long overdue for [a] major structural improvement projects. Most U.S. airports are aging, … and because of budgetary restrictions, they’re not aging well.”(Garcia and Clampet, 2015). The average US age is 40 years old with the youngest (Denver International) recently turning 20 years old. As airports continue to age, airport commissioners will struggle to find creative ways to either fund airport replacements or extend the service life of existing airport facilities (commonly referred to as service life extension projects or SLEP). Due to …