Risk Analysis Commons^™

Investigation Of Heavy Metal Composition And Associated Health Risks From Selected Groundwater Wells In Temeke, Dar-Es-Salaam, Justin M. Jeremiah

Tanzania Journal of Engineering and Technology (TJET)

Water quality continues to be the challenge to residents in Dar es Salaam due to various anthropogenic activities in the city. This study was conducted to assess groundwater quality by determining concentrations of heavy metals. Both probability and Nonprobability sampling techniques were used to collect samples from 40 groundwater wells in 24 wards of Temeke municipal and analysed using Microwave Plasma Atomic Emission Spectrometer (Agilent 4210 MP-AES) at the Geochemistry Laboratory of the University of Dar es Salaam. Results indicated varying heavy metal concentrations ranging from 0.71 ± 0.08 to 6.64 ± 0.21 mg/l for As, 0.02 ± 0.01 to …

Development And Testing Of Small-Scale Flash Dryer For Maize Bran, Eden Ngowi

Tanzania Journal of Engineering and Technology (TJET)

Sun drying is the most common technique used to dry various food products due to its economic convenience. However, it is not effective owing to its unreliable nature leading to microbial deterioration and aflatoxin contamination of food. In Tanzania, about 1.3 million tonnes of maize bran are at risk of deterioration annually due to improper drying. The aim of this study was to design, fabricate and test an efficient small-scale flash dryer for maize bran. Using principles of material and energy balance, a small-scale flash dryer with a throughput of 500 kg of dry product per hour was designed resulting …

Analysis Of The Factors Affecting The Oil Recovery From Oilseeds In A Multistage Crosscurrent Leaching Process, Samuel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

The analysis of the total oil recovery from oilseeds in a multi-stage crosscurrent leaching process is presented. The model created using mass balance equations for three stages was used to analyze the factors affecting total oil recovery, To. The key performance factors (raw meal feed flow rate, solvent feed flow rate in each stage, solvent distribution factor for each stage, percent oil in the raw meal (Poil), solids to solution ratio in the underflow (N), solvent to solids ratio (SSR), solvent to oil ratio (SOR) and wash ratio (WR) were varied while assessing To. While SSRi and SORi ranged from …

Inspection Planning Of Subsea Pipeline Using Risk-Based Inspection, Ni Luh Triska Adelia, Badrul Munir, Johny Wahyuadi Soedarsono

Journal of Materials Exploration and Findings

Pipelines are an important tool in oil and gas exploration. Pipeline is a transmission and liquid collection lines, including their accessories, which transport fluids from one plant to another. In transmission and collection process, there is a possibility of failure which can have minor to major impact on personnel injury, the environment and interrupt the business process. To maintain safety and to prevent accidents, the source and cause of failure needs to be calculated. Risk-based inspection (RBI) is a method that can be used to calculate the risk and determine the inspection planning both schedule and method, by combining the …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Study Of The Effects Of Thermal Aging Coupled With Shot-Peening Treatment Of Carbonitrided Din 1.6587 Low Alloy Steel On Retained Austenite And Residual Stresses, Richard J. Katemi

Tanzania Journal of Engineering and Technology (TJET)

This work investigated the effects of thermal aging and shot-peening of carbonitrided 1.6587 steel grade on retained austenite and residual stresses. After carbonitriding samples contained maximum of 0.87% carbon, 0.34% nitrogen and 50 mass. -% retained austenite. Thermal aging conditions investigated were -30°C, 90°C and 150°C while the aging period were 14, 96 and 720 hours. After thermal aging, some of the samples were subjected to shot-peening treatment using standard cut wire shots StD – G3 - 0.6 mm VDFI 8001 with intensity in the range of 0.25 to 0.30 mmA and coverage of 1.00 to 1.24 x 98%. It …

Evaluation Of Environmental Management System For Small And Medium Enterprises In Dar Es Salaam, Tanzania, Juma M. Matindana

Tanzania Journal of Engineering and Technology (TJET)

A system that manages environmental issues of Small and Medium Enterprises (SMEs) from the time of acquisition of raw materials up to disposal of the product is not well clear, especially in Tanzania. Most of the studies have been conducted in the field of environment management but few of them address the evaluation of the management of SMEs activities with respect to the environment. Although the nature of activities of SMEs has little noticeable environmental implications at the individual level but the impact is large due to diversification and labour intensity of these SMEs. SMEs employ about 20% of the …

An Overview Of Maternity Healthcare Monitoring In Developing Nations, Godphrey Kyambille

Tanzania Journal of Engineering and Technology (TJET)

A healthcare monitoring arrangement is essential for frequently monitoring a patient's health status. Specifically, maternal healthcare systems for tracking are utilized to evaluate the clinical status and monitor any abnormal condition changes during all three trimesters. This paper's objective is to conduct an extensive literature review and acknowledge earlier initiatives and studies conducted previously in maternal health care monitoring. This review focuses on accumulating information from earlier work and presents a general overview of previous studies concerning maternal health care monitoring (MHCM). The paper focuses on the maternal healthcare systems in developing countries accessed by pregnant women during the antenatal …

Developing Machine Learning And Time-Series Analysis Methods With Applications In Diverse Fields, Muhammed Aljifri

Theses and Dissertations

This dissertation introduces methodologies that combine machine learning models with time-series analysis to tackle data analysis challenges in varied fields. The first study enhances the traditional cumulative sum control charts with machine learning models to leverage their predictive power for better detection of process shifts, applying this advanced control chart to monitor hospital readmission rates. The second project develops multi-layer models for predicting chemical concentrations from ultraviolet-visible spectroscopy data, specifically addressing the challenge of analyzing chemicals with a wide range of concentrations. The third study presents a new method for detecting multiple changepoints in autocorrelated ordinal time series, using the …

Transitioning To A Lower Global Warming Refrigerant, A Performance Study Of R-513a And Hfc-134a In Commercial Chillers, Hossein Abedsoltan, Mark B. Shiflett

Chemical and Biochemical Engineering Faculty Research & Creative Works

The performance of R-513A and HFC-134a refrigerants is compared in two identical chillers operating at the University of Kansas. R-513A is a more environmentally friendly refrigerant due to its lower global warming potential that can be used as a retrofit replacement for HFC-134a in chillers. This study investigates the performance comparison of transitioning from HFC-134a to R-513A. The chillers have been in operation for two years, and cooling capacity, coefficient of performance, and other operating parameters are compared under similar cooling conditions. Cooling capacities ranged from 100 to 500 kW for both chillers. Overall, the energy consumption and coefficient of …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Ambient Air Emission Profiles Of Polycyclic Aromatic Hydrocarbons Around A Typical University Power House In Nigeria, Oyetunji Okedere

Tanzania Journal of Engineering and Technology (TJET)

The level of electricity generation in Nigeria is presently grossly inadequate. Consequently, the productive sectors of the economy do not presently enjoy an uninterrupted supply of electrical energy from the country’s national grid and the downtime is in most cases too much. Using diesel-fueled electric power generators has become an attractive alternative to meet the shortfall in the energy supply gap. In this study, the levels of polycyclic aromatic hydrocarbons in the vicinity of the diesel-fueled electric power generators operated by Osun State University, Osogbo, Nigeria were investigated with a view to ascertain the priority levels and carcinogenic PAHs. Since …

Isolation And Performance Test Of Green Low Dosage Hydrate Inhibitors From Local Materials For Improving Flow Assurance In Oil And Gas Industry, Makungu Madirisha

Tanzania Journal of Engineering and Technology (TJET)

The formation of gas hydrates in oil and gas industry can be minimized or prevented by the use of inhibitors. This paper reports on hemicellulose and modified lignin as low dosage gas hydrate inhibitors (LDGHIs). LDGHIs were isolated from sugarcane bagasse (SCB), plant gum exudates (PGE) of Acacia trees, and coconut coir, and further characterized by Attenuated Total Reflectance - Fourier Transform Infrared (ATR-FTIR) spectrometer, porosimeter and thermogravimetric analyzer (TGA). The PGE and SCB yielded 77.75% and 12.38% of hemicellulose, respectively, while coconut coir yielded 35.59% of lignin which was modified to sodium lignosulfonate (SLS) to improve its solubility in …

Assessment Of A Multi-Stage Wet Scrubber Performance Based On Characteristics Of Scrubbing Solution, Mahir Mohammed Said

Tanzania Journal of Engineering and Technology (TJET)

This paper presents the wet scrubber performance on acid gas absorption based on pH and conductivity measurements. The waste combustion system comprised of a CFB combustor in which mainly plastics waste was loaded into the riser (15 cm ID x 1.5 m long). The scrubbing experiments were conducted using a two-stage wet scrubber used as air pollution control device. The performance of the wet scrubber system was assessed by studying the changes in the pH and conductivity. The scrubbing solution was prepared using lime. The optimum lime concentration was obtained from bench experiments, giving an initial pH of up to …

Estimating Toxic Load From Finite-Duration Contaminant Releases In Wind Tunnel Experiments, Patrick B. Jones

Chemical Engineering Undergraduate Honors Theses

When gaseous contaminants are released into the atmosphere said contaminants form clouds that travel in the prevailing wind direction. An individual caught in the downwind path of one such cloud will accumulate a dosage, or toxic load, of said contaminant that is dependent on a multitude of environmental factors. This thesis quantifies unpredictability – or variation – in toxic load measurements using downwind concentration data captured from finite-duration gaseous contaminant releases conducted at set conditions in the Chemical Hazards Research Center ultra-low speed wind tunnel.

Finite-duration releases can be divided into two categories – time-limited steady releases and puffs – …

Extraction And Characterization Of Collagen From Cattle Horns For Potential Wound Healing, Yeriko Halson

Tanzania Journal of Engineering and Technology (TJET)

The need for bandages and gauze for wound dressing and healing is inevitable due to the high increase in accidents. Most of the material used for the production of bandages and gauzes for wound healing are from non-renewable synthetic material. The sustainability of non renewable resources is at jeopardy due to the health and associated environmental impact. Consequently, the use of naturally occurring and biodegradable material is a promising solution to the sustainability challenges of synthetic material. In this paper, the extraction of collagen films from cattle horns for potential wound healing is reported. Collagen was extracted from cattle horns …

Scale Modeling Of An Appearance Of Downwash Pattern Of Hot Smoke Ejected From Chimney In The Turbulent Cross Flow, Xangpheuak Inthavideth, Nobumasa Sekishita, Sounthisack Phommachanh, Yuji Nakamura

Progress in Scale Modeling, an International Journal

This study aims to elucidate the scaling law to provide the critical condition on appearance of the downwash pattern of the hot smoke ejected from a chimney in a turbulent cross flow. A specially designed wind tunnel with an active turbulence generator developed by Makita was adopted to offer a quasi-isotropic turbulence field in a lab-scale test facility. A heated jet with smoke is issued into the cross flow from the vertically oriented chimney placed in the test section of the wind tunnel. In this study, the experimental parameters considered are temperature of the heated jet (smoke), jet ejected velocity, …

Contents, Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

Preface Of Volume 1 Issue 1 On Journal Of Materials Exploration And Findings (Jmef), Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

The Optimization Of Failure Risk Estimation On The Uniform Corrosion Rate With A Non-Linear Function, Fernanda Hartoyo, Jaka Fajar Fatriansyah, Imam Abdillah Mas'ud, Farhan Rama Digita, Hanna Ovelia, D. Rizal Asral

Journal of Materials Exploration and Findings

Failures in the oil and gas pipeline system are conditions that must be avoided and anticipated because the losses due to the failures can occur at a very high level. Internal corrosion is one of the significant causes of the failures in pipeline systems. In addition, this type of corrosion is due to the high content of carbon dioxide and other corrosive substances in crude oil and natural gas. Therefore, an optimal inspection scheduling system is required to prevent the possibility of pipeline failures due to corrosion and to avoid any overspending on the budget due to excessive inspection scheduling. …

Open-Field Scale-Model Experiments Of Fire Whirls Over L-Shaped Line Fires, Yuto Iga, Kazunori Kuwana, Kozo Sekimoto, Yuji Nakamura

Progress in Scale Modeling, an International Journal

This paper presents the results of open-field scale-model experiments of fire-whirl formation over line fires. L-shaped line fires were burned in crosswinds, and the processes of fire-whirl formation were observed. The flame height was measured using an image-processing technique, while two-dimensional velocity components were measured at two different locations using ultrasonic anemometers. Two tests were selected for comparison: test A, in which intense fire whirls repeatedly formed, and test B, in which no whirls were observed. In test A, the wind flow was bent by the fire plume, creating swirling flows near the burning area, thereby forming fire whirls. On …

A Study On Fire Hazards Of Oil Tanks In Urban Areas With Scale Model Experiments, Ho Yin Ng, Yu Wan, Wan Ki Chow

Progress in Scale Modeling, an International Journal

Large fuel tanks are located in an urban area of Tsing Yi in Hong Kong, giving potentially high risks to people living nearby if a fire was to occur. Scale modeling experiments were carried out to investigate the potential of fire hazards. Propanol pool fires with five different scales of oil tanks were studied first. Appropriate tank sizes were then put in a 1/2500 architectural scale model on the Tsing Yi Island to study a fuel tank fire. Results show that the heat and smoke from a fire would affect occupants staying in areas near to the fuel tanks. Fire …

Effects Of Calcination Temperature Of Naturally Occurring Absorbents On Drinking Water Defluoridation, Brenda Mndolwa

Tanzania Journal of Engineering and Technology (TJET)

Currently, in Tanzania, fluoride removal from drinking water is treated mostly using the bone char method. The method has poor acceptability in some religious communities and also causes water quality deterioration in taste and odour if the bones are not properly prepared. The use of local natural adsorbents as an alternative is feasible with limitations of high levels of other impurities in treated water. Locally available gypsum, magnesite and bauxite were converted to adsorbents through calcination. The study was conducted to determine the removal efficiency, best calcination temperature and composite ratio of the three adsorbents for the removal of fluoride …

Quantitative Risk Assessment And Dispersion Modelling Using Aloha For Chlorine Gas Handling Facility, Kusala Uvaraja

Student Works (2020-2029)

Malay-Sino Chemical Industries Sdn Bhd (Lahat) is a chlor-alkali industry consist of Emergency Chlorine Gas Handling Facility (ECGHF) which have the tendency to affect the plant workers and nearby residential area in the event of accidental chlorine gas release. HAZOP tool with risk assessment was used to identify the hazard and quantifying the hazards in order to prioritize the recommendations at the ECGHF. Possible incident scenario was selected from the HAZOP outcome which was the chlorine gas release from the stack due to scrubbing flow failure. The consequences of the released chlorine gas to the atmosphere was simulated by using …

Time-Dependent Reliability Framework For Durability Design Of Frp Composites, Rajneesh Kumar Bharil

Graduate Theses, Dissertations, and Problem Reports (ETD)

The life-cycle performance, durability, and aging characteristics of Fiber Reinforced Polymer (FRP or Structural Composites) have been of keen interest to the engineers engaged in the FRP design, construction, and manufacturing. Unlike conventional construction materials such as steel and concrete, the design guidelines to account for the aging of FRP are somewhat scattered or not available in an approved or consistent format. Loss of strength over time or aging of any structural material should be of concern to engineers as the in-service lifespan of many engineering structures is expected to exceed 100 years. Use of durability strength-reduction factors or factors …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Measuring Risks Of Interdependencies In Enterprise Systems: An Application To Ghana’S Salt Enterprise, Yaw Mensah

Engineering Management & Systems Engineering Theses & Dissertations

This dissertation describes the use of Functional Dependency Network Analysis (FDNA) for modeling risks resulting from dependencies among elements of enterprise systems with application to salt processing enterprise in Ghana. FDNA was developed to model dependencies among members of enterprise systems by highlighting two dimensions of dependency: strength and criticality. Nonetheless, the concepts and analytics for these two dimensions of dependencies needed further development and generalization in the context of project management and systems development in developing countries.

Managing risks within the interdependency in enterprise systems through integration will help improve global economic growth. Coherent theory for enterprise integration must …