Industrial Technology Commons^™

Mathematical Modelling Of Nitrification And Denitrification Processes Based On Neuro-Fuzzy Bioreactor Models, Mirkhalil Agzamovich Ismailov, Boburbek Zokirjon Ugli Mannobjonov

Technical science and innovation

This paper presents the development and investigation of hybrid neural network and fuzzy models for the mathematical modelling of nitrification and denitrification processes in a biological wastewater treatment bioreactor. A comprehensive approach is proposed, integrating a mechanistic model of the ASM1/ASM2d type with neural networks (LSTM and Gaussian Process Regression), as well as a fuzzy control system based on an extended set of expert rules. A digital twin of the bioreactor was developed to allow for the prediction of the dynamic behavior of key parameters such as NH₄⁺, NO₃⁻, dissolved oxygen, etc. within a prediction range of 1 to 12 …

Determination Of The Content Of Water-Soluble Vitamins In The Composition Of Beet Beetroot Composition, Jasur Esirgapovich Safarov, Shakhnoza Abduvaxitovna Sultanova, Muhammad Rasul Oglu Najafli, Doston Ishmuhammat Ugli Samandarov

Chemical Technology, Control and Management

The aim of this study was to determine the content of water-soluble vitamins in various parts of beetroot (pulp, leaves and stems) that had been subjected to various drying methods in a bid to explore the effect of physical processes, i.e., the application of ultrasound, on micronutrient preservation. The experiments were performed at the Department of Service Technologies of Tashkent State Technical University, and chromatographic analysis was performed in the Institute of Bioorganic Chemistry of the Academy of Sciences of the Republic of Uzbekistan. Chromatography was performed on Agilent-1200 chromatograph with Exlipse XDB C18 column and diode array detector using …

Selfish Herd: Emergence Of Distributed Sensing, Timothy Mascal

Discovery Day - Daytona Beach

The problem of multi-agent swarm formation control seeks decision frameworks that exhibit desirable emergent behavior, including distributed sensing and communication, while remaining resilient to environmental noise. Previous work has demonstrated that the Selfish Herd Model is not only resilient to simulated sensor noise but performs better in its presence. This work further investigates the emergent behaviors of the Selfish Herd Model, particularly distributed sensing, by investigating whether the swarm achieves global stability equivalent to that observed in previous work utilizing global knowledge. A parameter variation study was performed across varying agent visual range and maximum neighbor count inputs to simulate …

Innovative Controls For Combustible Particulate Dust In Industrial Refineries, Sadie Dickman

Discovery Day - Daytona Beach

This project entails an extensive analysis of the occupational combustible dust hazard that exists in industrial refineries, including food processing, manufacturing, and metalworking facilities. Based on prior accidents like the 2008 Imperial Sugar and 2017 Didion Milling explosions, combustible dust causes fire and explosion risks that can result in damages, injuries, and fatalities. Through comparison of OSHA regulations, NFPA standards, and accident data, a lack of effective standards regarding training, audits, ventilation, fire prevention, and adequate housekeeping measures were highlighted to be an existing safety gap. The purpose of this study is to propose administrative controls to mandate companies to …

Implementation Of The Fourth Industrial Revolution Technologies In Tanzania’S Downstream Oil And Gas Industries, Vitalis John Mwinyi

Tanzania Journal of Engineering and Technology (TJET)

The advent of the fourth industrial revolution (IR4.0) has resulted in the digital transformation of multiple sectors of the economy due to the disruptive nature of the technologies driving the revolution. The technologies have already found their way into the oil and gas industries across the globe, especially in upstream, midstream, and downstream operations. However, the degree of implementation is not the same for these operations, considering the complexities involved, integrated process, the associated risk and investment cost, among others. This study aimed to establish the implementation level of IR4.0 technologies in the downstream operations. A survey method was employed …

Ai-Based Porosity Detection In Babbitt Bore Turning, Kaylee Leggett, Hannah Adams Gemmell, Kaisa Shingleton

Williams Honors College, Honors Research Projects

For this project, an external company reached out to the University of Akron requesting assistance with defect detection during their vertical turning operations. As babbitt is removed in a vertical turning process, it occasionally reveals defects, mainly porosity, which can lead to costly downstream failures of the part. Current inspection techniques involve use of dye penetrant, which is time consuming, labor intensive, unergonomic, and a source of human error. The goal of the project is to create an alternative inspection method using an AI-based machine-learning model. After the turning operation, a camera is deployed to perform an in-place inspection, taking …

The Design And Effect Of Continuum Robot Compliance On Locomotion, Parsa Molaei

LSU Doctoral Dissertations

Continuum robots, due to their compliant structures and ability to navigate through constrained environments, offer significant advantages in applications requiring safe physical interaction and dexterous motion. However, challenges related to limited structural stiffness, payload capacity, and precise control remain open problems in the field. This dissertation presents novel contributions aimed at addressing these limitations through two main actuation units of continuum robots: tendon-driven continuum robots (TDCRs) and concentric tube robots (CTRs). In the first part, we focus on methods to improve the stability and modify the stiffness of the TDCR. A tendon decoupling strategy is introduced for planar TDCRs. The …

Comparative Evaluation Of Linear Regression, Cross Validation And Regularization Approaches In Multivariate Data Analysis, Ransford Owusu, Felix Yeboah, Francis Effah Boateng

Data Science and Data Mining

This study evaluates linear regression and its enhanced variants incorporating cross-validation and regularization techniques for high-dimensional, multivariate datasets. We address challenges such as multicollinearity and overfitting. Methods including Ridge, LASSO, and Elastic Net are compared against ordinary least squares regression. Empirical analysis using an automobile dataset for fuel efficiency prediction shows that while OLS regression captures basic relationships, its limitations are mitigated through regularization and cross-validation, resulting in improved model interpretability. The findings provide a comprehensive framework for predictive modeling in complex data environments and offer insights into statistical methodology and practical applications in the automobile industry.

Ease Of Product Disassembly Through A Systematic Structured Time-Based Design For Disassembly Methodology, Emeka S. Igwe

College of Graduate Studies: Theses & Dissertations

This research introduces a systematic time-based design for disassembly (DfD) framework aimed at optimizing product disassembly by addressing important features like liaisons between components in product, component accessibility and the overall modularity of the product. This study specifically covers electromechanical and mechatronic systems in both household and industrial setup, identifying their disassembly challenges and high value pointers for improvement. The methodology involves using a design for disassembly framework called LeanDfD in carrying out a holistic disassembly process and evaluating quantitative metrics like disassembly time and complexity and suggesting further redesign strategies to minimize disassembly time and cost. Adopting this systematic …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Dynamic Model Of An Overhead Crane, Leonard Ruesga

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this thesis a novel spatial model of an overhead crane was developed. The model includes: bridge, trolley, driving and follower wheels for the bridge and trolley, drum, cable, and the payload. The model accounts for the winding/unwinding of the cable around the drum as the payload is raised/lowered. The cable and the payload were considered as rigid bodies with uniformly distributed mass. First, the kinematic equations of the model were developed by using constraint equations. Second, the dynamic equations were derived through use of Newton’s Laws. Developing the rotational dynamic equations required the determination of the angular momentum vectors …

A Screening Life Cycle Analysis Of One-Way And Reusable Crate Designs – Estimating Environmental Impacts Via Lca Software, Nicolas R. Corona

Master's Theses

A comparison analysis conducted via COMPASS life cycle analysis software has indicated that a one-way crate design, rather than a reusable crate design, is in fact the more environmentally friendly packaging system. These results can be interpreted differently, however, as the manufacturer of said crate designs must confirm what impact indicators they would like to reference as environmental goalposts. The conducted analysis provides insight into what the environmental impacts of each packaging system look like as packaging at all three system levels has been identified as a means of reducing environmental impacts globally. As such, the manufacturer of said crate …

Containerization Of Seafarers In The International Shipping Industry: Contemporary Seamanship, Maritime Social Infrastructures, And Mobility Politics Of Global Logistics, Liang Wu

Dissertations, Theses, and Capstone Projects

This dissertation discusses the mobility politics of container shipping and argues that technological development, political-economic order, and social infrastructure co-produce one another. Containerization, the use of standardized containers to carry cargo across modes of transportation that is said to have revolutionized and globalized international trade since the late 1950s, has served to expand and extend the power of international coalitions of states and corporations to control the movements of commodities (shipments) and labor (seafarers). The advent and development of containerization was driven by a sociotechnical imaginary and international social contract of seamless shipping and cargo flows. In practice, this liberal, …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Dependence Of The Granulometric Composition Of Chalk During Granulation In A Turbulized Layer, N.A. Annaev, S.Kh. Nurmukhamedov, Zh.V. Sultonov, N.Sh. Khudoiberdieva

Chemical Technology, Control and Management

The article presents the results of an experimental study on chalk granulation in the turbulized layer of a turboblade granulator. The design of the apparatus combines the following sequential processes: grinding, granulating and compacting newly formed granules. In addition, this device has the ability to carry out both rotational and reciprocating motion. It has been established that preliminary grinding of the feedstock increases the efficiency of the granulation process and improves the quality of the finished product. In the experiments, four substances were used to create 2 astringent suspensions and the optimal combination and their ratios were determined. The experiments …

Wire Deflection Investigation During Wedm Of Aisi 304 Stainless Steel: An Experimental And Numerical Study, Sara A. El-Bahloul, Mohamed G. Elkhateeb

Mansoura Engineering Journal

Wire electrical discharge machining (WEDM) is a specific form of electrical discharge machining that employs a small diameter wire electrode to cut a narrow kerf in the workpiece. Since the wire deflection has a negative effect on the performed cutting, this research seeks to study the resultant wire deflection during WEDM of AISI 304 stainless steel. This study is performed with the help of three types of modeling; namely, mathematical modeling, experimental modeling, and thermo-mechanical finite element modeling. The mathematical modeling is performed to analyze the stresses and the wire lag, while the experimental modeling is achieved to observe the …

A Hybrid Metaheuristic And Computer Vision Approach To Closed-Loop Calibration Of Fused Deposition Modeling 3d Printers, Graig S. Ganitano, Shay V. Wallace, Benji Maruyama, Gilbert L. Peterson

Faculty Publications

Fused deposition modeling (FDM) is one of the most popular additive manufacturing (AM) technologies for reasons including its low cost and versatility. However, like many AM technologies, the FDM process is sensitive to changes in the feedstock material. Utilizing a new feedstock requires a time-consuming trial-and-error process to identify optimal settings for a large number of process parameters. The experience required to efficiently calibrate a printer to a new feedstock acts as a barrier to entry. To enable greater accessibility to non-expert users, this paper presents the first system for autonomous calibration of low-cost FDM 3D printers that demonstrates optimizing …

Fungi In Flux | Designing Regenerative Materials And Products With Mycelium, Arvind Bhallamudi

Masters Theses

As the world grapples with the escalating crisis of climate threats and environmental degradation, this research delves into the synergistic potential of design and biology, developing safe and sustainable materials for applications in prototyping, furniture and interior design. Harnessing the power of a unique organism - fungi, the study proposes an accessible, efficient, and resilient material resource system. It utilizes local waste streams and mycelium (the vegetative part of fungi) to grow functional structures. An experimental and small-scale protocol is modeled by testing bio-fabrication and bio-printing methods. The composites' performance qualities and characteristics are evaluated through mechanical testing and a …

Generalizable And Adaptable Data-Driven Methods For Overcoming Barriers To Practical Industrial Condition Monitoring, Matthew B. Russell

Theses and Dissertations--Electrical and Computer Engineering

The future of smart manufacturing relies on predictive maintenance systems that intelligently minimize expensive downtime through timely assessment of machine condition. Deep Learning (DL) has achieved excellent performance in industrial condition monitoring experiments, but the constraints of the manufacturing environment prevent many algorithms from being practically deployed on the factory floor. Ubiquitous sensing from online machines generates high velocity data streams that require new techniques for efficient transmission and storage. Despite these ever-increasing data lakes, many applications still lack the data needed for training DL fault diagnosis and wear tracking models since most data is unlabeled and only from nominal …

Evaluating Electrification Of Fossil Fuel-Fired Boilers For Decarbonization Using Discrete Event Simulation, Nahian Ismail Chowdhury

Graduate Theses, Dissertations, and Problem Reports (ETD)

Decarbonizing fossil fuel usage is crucial in mitigating the impacts of climate change. CO2, which comprises the major portion of greenhouse gas, is emitted from burning fossil fuels. One of the significant sources of fossil fuel user is industrial process heating, and most of the heating in industrial processes is achieved through boilers. Electrification is a promising solution for decarbonizing these boilers, as it enables renewable energy sources to generate electricity, which can then be used to power the electric boilers. The electrification of boilers can reduce greenhouse gas emissions, improve air quality, and increase energy efficiency. However, it requires …

Smart Manufacturing—Theories, Methods, And Applications, Zhuming Bi, Lida Xu, Puren Ouyang

Information Technology & Decision Sciences Faculty Publications

(First paragraph) Smart manufacturing (SM) distinguishes itself from other system paradigms by introducing ‘smartness’ as a measure to a manufacturing system; however, researchers in different domains have different expectations of system smartness from their own perspectives. In this Special Issue (SI), SM refers to a system paradigm where digital technologies are deployed to enhance system smartness by (1) empowering physical resources in production, (2) utilizing virtual and dynamic assets over the internet to expand system capabilities, (3) supporting data-driven decision making at all domains and levels of businesses, or (4) reconfiguring systems to adapt changes and uncertainties in dynamic environments. …

Chemical Clean Automated Loader, Jordyn Bryner

Williams Honors College, Honors Research Projects

TTM Technologies (TTM) is a global printed circuit board (PCB) manufacturer. The work described in this report was completed in the TTM North Jackson, Ohio location. This plant focuses primarily on the manufacturing of rigid and rigid-flex PCBs for the aerospace and defense industry. TTM North Jackson has an ongoing labor dependency issue due to the shortage of workers the nation is facing. To solve this problem, TTM has focused the efforts of their new engineers and interns on automating processes that are labor dependent. The goal is to provide design guidance to be used later by TTM to automate …

Compact In-Rack Dielectric Immersion Cooling System, Salvador Landeros Jr, Joshua M. Hannaman, Marshall D. Reid

Mechanical Engineering

The Compact Dielectric Cooling team consisting of Josh Hannaman, Marshall Reid, and Salvador Landeros worked with Aria Technologies to create a thermal management system for data centers that can easily implement liquid cooling into current infrastructure for high density computing servers. The project was to design, build, and test a compact immersion cooling system for a senior project at California Polytechnic State University – San Luis Obispo. Immersion cooling is a liquid-cooling process that involves the immersion of electrical IT equipment and the removal of heat from the hot IT components using dielectric liquid. The goal was to build a …

Integration Of Blockchain Technology Into Automobiles To Prevent And Study The Causes Of Accidents, John Kim

Electronic Theses, Projects, and Dissertations

Automobile collisions occur daily. We now live in an information-driven world, one where technology is quickly evolving. Blockchain technology can change the automotive industry, the safety of the motoring public and its surrounding environment by incorporating this vast array of information. It can place safety and efficiency at the forefront to pedestrians, public establishments, and provide public agencies with pertinent information securely and efficiently. Other industries where Blockchain technology has been effective in are as follows: supply chain management, logistics, and banking. This paper reviews some statistical information regarding automobile collisions, Blockchain technology, Smart Contracts, Smart Cities; assesses the feasibility …

An Improved Earned Value Management Method Integrating Quality And Safety, Brian Briggs

LSU Doctoral Dissertations

The construction industry invests significant time and money to improve quality and safety while reducing cost and schedule impacts. The industry has a sincere desire to improve construction project management methods to improve efficiency. Historically, quality and safety underperformances result from undermanaged quality control and safety activities. The cost and schedule impacts associated with poor quality work have always had an impact on construction operations. The unprecedented challenges and uncertainties of COVID-19 highlighted the need to improve the Earned Value Management (EVM) method within construction to reflect these quality and safety activities. The central goal of this dissertation is to …

Problem Solving Methods For Synthesis Of Physical Principles Of Mechatronic Module Operations In Intelligent Robotic Systems, Nazarov Khayriddin Nuritdinovich

Chemical Technology, Control and Management

The scientific paper investigates the methods for solving problems of synthesis of physical principles of operation of mechatronic modules of intelligent robotic systems are considered.

In addition, it deals with the specifics of the process of synthesis of the physical principles of the operation of mechatronic modules using predicate models, list models and information matrices of physical and technical effects.

It shows the interpretation of the components of the model of the system for the synthesis of the physical principles of operation of mechatronic modules of intelligent robotic systems and automatic control and the features of the synthesis algorithm for …

Development Of A Marine Biodegradable Target Balloon, Blake Samuel Robinson, Arash Sam Akhavi, David Leonardo Albarran-Martinez

Materials Engineering

The US Navy utilizes PVC target balloons, known as Killer Tomatoes, that are inflated onboard a naval vessel then deployed into the ocean to calibrate a variety of weaponry. The Navy has requested the investigation of biodegradable polymers to replace the PVC in attempts to reduce ocean waste that is generated from the leftover PVC material. After communicating with American Pacific Plastic Fabricators (APPF), the current manufacturer of the Killer Tomatoes, we gained an understanding of the manufacturing process and the material requirements that would allow a new material to be integrated into their current process. Two proprietary, trial polymers …

Inventory Locating With Quuppa: The Design And Development Of A Real-Time Process Monitoring Web Application Solution, Dylan C. Moreland, Trevor J. Howell, John W. Takiff, Patrick S. Dillon, Theo E. Fritz, William K. Mcintyre

Industrial and Manufacturing Engineering

Viasat, Inc. requires precise inventory tracking at their production facility in San Diego, CA. Viasat has installed the Quuppa indoor real-time locating system (RTLS), which it uses to track the real-time position of high-value work-in-process items. In its current state, the system only displays in-the-moment location information, with no available functionality for storing historical data for review, analysis, or visualization. In addition, the data displayed is noisy and prone to significant random error. This paper provides an overview of RTLS methods and technologies, assesses alternative solutions to Viasat’s issue, demonstrates our RTLS integrated web app solution, analyzes its impact, and …

Generic Design Methodology For Smart Manufacturing Systems From A Practical Perspective, Part I—Digital Triad Concept And Its Application As A System Reference Model, Zhuming Bi, Wen-Jun Zhang, Chong Wu, Chaomin Luo, Lida Xu

Information Technology & Decision Sciences Faculty Publications

Rapidly developed information technologies (IT) have continuously empowered manufacturing systems and accelerated the evolution of manufacturing system paradigms, and smart manufacturing (SM) has become one of the most promising paradigms. The study of SM has attracted a great deal of attention for researchers in academia and practitioners in industry. However, an obvious fact is that people with different backgrounds have different expectations for SM, and this has led to high diversity, ambiguity, and inconsistency in terms of definitions, reference models, performance matrices, and system design methodologies. It has been found that the state of the art SM research is limited …

Generic Design Methodology For Smart Manufacturing Systems From A Practical Perspective. Part Ii—Systematic Designs Of Smart Manufacturing Systems, Zhuming Bi, Wen-Jun Zhang, Chong Wu, Chaomin Luo, Lida Xu

Information Technology & Decision Sciences Faculty Publications

In a traditional system paradigm, an enterprise reference model provides the guide for practitioners to select manufacturing elements, configure elements into a manufacturing system, and model system options for evaluation and comparison of system solutions against given performance metrics. However, a smart manufacturing system aims to reconfigure different systems in achieving high-level smartness in its system lifecycle; moreover, each smart system is customized in terms of the constraints of manufacturing resources and the prioritized performance metrics to achieve system smartness. Few works were found on the development of systematic methodologies for the design of smart manufacturing systems. The novel contributions …