Industrial Technology Commons^™

Size Effects In Human Visual Inspection For Micro/Meso Scale Parts, Sri Harsha Kavuri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Visual inspection has been a major method of quality control in conventional manufacturing processes for the last fifty years. Utilizing trained human inspectors to perform this visual inspection has been the most effective means of maintaining quality control. Extensive research has been performed to understand the factors that influence the human inspection process.

In the recent years, there has been a significant emphasis on manufacturing at the smaller end of the size-spectrum such as Micro and Meso scale manufacturing. Quality control at becomes a challenging task due to the extremely small sizes. Several automated visual inspection techniques have been proposed …

Color Removal From Pulp Mill Effluent Using Coal Ash Produced From Georgia Power Coal Combustion Plants, Christopher B. Willett

College of Graduate Studies: Theses & Dissertations

Two environmental concerns currently face Georgia: coal fly ash (CFA) waste from coal power plants, and the effluent generated by pulp mills. Pulp mill effluent discolors surface waters into which it is discharged, and has been proven to negatively impact the dissolved oxygen and carbon necessary for aquatic life. The proposed solution is a cost-effective adsorption treatment using an inexpensive but abundantly available waste material: CFA. CFA possesses beneficial properties that allow it to effectively remove contaminants, and is available at significantly reduced cost. The primary research objective was to define treatment parameters that would result in the maximum removal …

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …

A Comparative Analysis Of Spatial Visualization Ability And Drafting Models For Industrial And Technology Education Students, Petros Katsioloudis, Vukica Jovanović, Mildred Jones

Engineering Technology Faculty Publications

The article presents the comparative study on the drafting models and spatial visualization ability of industrial and technology education students in the U.S. It discusses how the study was conducted which examined the issue based on technical drawings and with regards to the impacts of model types. The results reportedly revealed three-dimensional models are effective for promoting learning, however more studies have to be conducted.

Assessment Of Solar Photovoltaic Technologies Using Multiple Perspectives And Hierarchical Decision Modeling, Nasir Jamil Sheikh

Dissertations and Theses

The objective of this research is to build a decision model for a comprehensive assessment of solar photovoltaic technologies using multiple perspectives. These perspectives include: social, technological, economic, environmental, and political (STEEP) with each perspective consisting of multiple criteria. Hierarchical decision modeling and expert judgment quantification are used to provide the relative ranking of the perspectives and criteria. Such modeling is effective in addressing technology evaluations with competing and contrasting perspectives and criteria where both quantitative and qualitative measurements are represented. The model is then operationalized by constructing desirability functions for each criterion. The combined results provide an overall numerical …

A Digital Hydraulic Valve, Actuated Using A Piezoelectric Linear Motor, Brian C. Bevill

Purdue Polytechnic Directed Projects

Proportional control in hydraulics is widely utilized. The most widely used current types of proportional valves utilize solenoid technology. While this technology has been around for decades and has been proven an effective means of control, there is always a demand for improved performance of advancing technologies. Integrating piezoelectric devices as a means to control hydraulic systems helps advance control for hydraulic systems.

Piezoelectric stack devices have been used to control hydraulic systems with success. Advantages of these stacks include being relatively small with a high power to weight ratio, using less energy than solenoid operations, and being fast acting. …

Optimum Failure Truncated Testing Strategies, Erik Kostandyan

Dissertations

Accumulated fatigue damage on mechanical components due to random stress loads eventually causes failure. Therefore products with lower failure rates are more desirable. Testing mechanical components for their intended purpose under predetermined working conditions is a common practice used by industries to prevent failures. Fatigue tests are categorized as Time Truncated or Failure Truncated, known in the literature as Type I and Type II tests, respectively. In failure truncated tests, the mechanical components are tested until the desired number of results is obtained. The parameters of a typical failure truncated test include the capacity of the test facility, the actual …

Analysis Of Possible Use Of Identification Technologies In Disassembly, Vukica Jovanović, Sreten Filipović, Gordana Ostojić, Stevan Stankovski, Milovan Lazarević

Engineering Technology Faculty Publications

The barcodes and Radio Frequency Identification tags that are being used during manufacturing, assembly, warehousing, and distribution could also be reused at the end of the product lifecycle for an identification of the correct disassembly process that would result in recycling of its components. The barcodes or RFID tags can be helpful in identifying objects in terms of sustainable development, regarding disassembly, recycling and reuse. In this paper, the analysis of the current applications of RFID Technology in the final phase of the product lifecycle will be presented. The simulation of the disassembly process supported by both barcode and RFID-enabled …

Analysis Of Factors Causing Failure Mode For Automotive Hitch Control System Calibration In Agriculture Equipment, Setordji Yao Abotsi

Dissertations and Theses @ UNI

Traditionally, agricultural tractors have used hydro-mechanical draft control systems to mechanically sense implement draft. Technological development of low cost, reliable microprocessors has contributed to allowing greater flexibility in designing agricultural tractor control systems (Rutkowski & Welchens, 1986). To successfully control the depth of which an implement penetrates the ground, it has become imperative to incorporate a draft control system on agricultural tractors. The control system operates by responding to the draft load or force acting on the tractor. Increasing the draft load or force allows the implement to be raised and decreasing the draft load or force allows the implement …

Disassembly Planning And Costing Through Petri Net Approach, Chunhsi Lei

Mechanical & Aerospace Engineering Theses & Dissertations

In the current consumer oriented environment, many new products appear in the market almost on a daily basis. Lured by advertisements and tempted by new product features, customers are constantly purchasing newer products. Acquiring newer products for often leads to throwing out older ones, but it is a totally different story for manufacturers. They need to consider the best way to reuse a product both for economic purposes and for environmental protection. Considerations for them often include: how to minimize total disassembly cost, how to achieve the lowest total disassembly time at each processing step, and how to sort valuable …

Windmill Documentary, Timothy David Stoltenburg

Honors Capstones

Capstone submitted as a graduation requirement for the BSU Honors Program.

Life Cycle Impact Assessment Method For Early Design Phase Of Industrial Products, Harpreet Singh Multani

Mechanical & Aerospace Engineering Theses & Dissertations

The objective of this thesis is to develop a simplified life cycle impact assessment method that can reliably and quickly provide the values of Eco-indicator 99 single score, the Eco-indicator damage categories score (human health, ecosystem quality, resource depletion), environmental impacts like global warming, ozone depletion, acidification, eutrophication, photochemical oxidants potential of the product/process, which could be used in the initial design stages for alternative design comparisons and product improvements, thus leading towards green manufacturing.

To achieve this, a variety of products have been chosen and the life cycle inventory data is gathered from the environmental product declarations that are …

Reaction Based Grasp Force Assignment, Mark W. Hunter

Theses and Dissertations

An iterative method is developed by which the contact forces required to apply an arbitrary wrench (six elements of force and moment) to a stably grasped object may be calculated quickly. The assignment of contact forces, given a required object wrench, is accomplished with the use of fuzzy logic. This concept is referred to as the fuzzy logic reactive system (FLRS). The solution is versatile with respect to goals inherent in the rulebase and the input parameters, and is also applicable for an arbitrary number of contacts. The goal presented in this research, to illustrate the concept of the FLRS, …