Industrial Engineering Commons^™

Development Of A Genetic Algorithm Based Search Strategy Suited For Design Optimisation Of Internal Combustion Engines, Nalitolela G

Tanzania Journal of Engineering and Technology (TJET)

Engine design optimisation is a multi-objective, multi-domain problem in a discontinuous design space. The state of the art of optimisation techniques shows that only methods of direct and adaptive search are appropriate for this type of problem. These include, adaptive random search, simulated annealing, evolution strategies and genetic algorithms. Of these methods, the genetic algorithms have been shown to be the most suited for the optimisation of multi-modal response functions in a discontinuous design space. This paper considers the important characteristics of genetic algorithms and their adaptation for use in parametric design optimisation of internal combustion engines. In order to …

A Project-Based Electronics Manufacturing Laboratory Course For Lower-Division Engineering Students, Jianbiao Pan, Albert Liddicoat, James G. Harris, Dominic Dal Bello

Industrial and Manufacturing Engineering

This paper presents a project-based laboratory course on electronics design and manufacturing. The goal of this course is to provide lower-division engineering students a hands-on experience involving actual printed circuit board (PCB) design, layout, fabrication, assembly, and testing. Through project-based learning, students not only learn technical skills in designing and manufacturing an electronic device, but also develop their project management and communication skills early in their course of study at the university. The course outline and examples of the student projects are presented in this paper as well as project evaluations and students’ feedback. This paper also presents the selection …

Curricular Enhancement To Support Project-Based Learning In Computer And Electrical Engineering, Albert Liddicoat, Jianbiao Pan, James G. Harris, Lynne A. Slivovsky

Industrial and Manufacturing Engineering

Undergraduate computer and electrical engineering programs often partition the curriculum into several courses based on related topics taught in isolation. Students are expected to synthesize their knowledge in a senior design project. It is the authors’ experience that students often struggle during their senior design project since they have not gained the appropriate knowledge or mastered necessary skills needed to work on a significant or team-based engineering design project. Specifically, students need to be able to define system requirements, partition the design into subcomponents, design, build, test, and verify that the system requirements have been met. The authors have enhanced …

Enhancing Student Learning Through State-Of-The-Art Systems Level Design And Implementation: The Development Of A Lower Division Learning Module, James G. Harris, Dominic Dal Bello, Jianbiao Pan, Albert Liddicoat

Industrial and Manufacturing Engineering

The Cal Poly/Allan Hancock team is developing a learning module that will allow all lower division engineering students to design, fabricate, assemble, and test an electronic system implemented on a printed circuit board (PCB). All the services necessary to perform this laboratory experiment will be provided with low-cost vendors available on the . The learning module is being developed so that it can be integrated into the existing electrical engineering lower division courses that are required by all engineering students. The laboratory learning module will use operational amplifiers (op amp), resistors, capacitors and other common electronic components to study the …

Techniques For Developing Large Scale Fuzzy Logic Systems, Jon C. Ervin, Sema E. Alptekin

Industrial and Manufacturing Engineering

In this paper, we describe various techniques used to make Intuitionistic Fuzzy Logic Systems amenable to operating on applications with large numbers of inputs. A rule reduction technique known as Combs method is combined with an automated tuning process based on Particle Swarm Optimization. A second stage of tuning on rule weights results in improved performance and further reduction in the size of the rule-base. The entire process has been developed to operate within the Matlab software environment. The technique is tested against the Wisconsin Breast Cancer Database. The use of these tools shows great promise in significantly expanding the …

Drop Test Reliability Of Lead-Free Chip Scale Packages, Andrew Farris, Jianbiao Pan, Albert Liddicoat, Brian J. Toleno, Dan Maslyk, Dongkai Shangguan, Jasbir Bath, Dennis Willie, David A. Geiger

Industrial and Manufacturing Engineering

This paper presents the drop test reliability of 0.5 mm pitch lead-free chip scale packages (CSPs). Fifteen 0.5 mm pitch CSPs were assembled on a standard JEDEC drop reliability test board with Sn3.0Ag0.5Cu lead-free solder. Eight boards were edge-bonded with a UV-cured acrylic; eight boards were edge- bonded with a thermal-cured epoxy; and twelve boards were assembled without edge bonding. Half of the edge-bonded test boards were subjected to drop tests at a peak acceleration of 1500 G with a pulse duration of 0.5 ms, and the other half subjected to drop tests at a peak acceleration of 2900 G …

The Effects Of Build Orientation, Diameter And Printhead Life On The Cylindricity Of Three-Dimensionally Printed Parts, Troy E. Ollison

All-Inclusive List of Electronic Theses and Dissertations

Rapid prototyping (RP) technologies have become more than just a fast and inexpensive way to produce prototypes. Today RP is widely used to produce functional prototypes, end-use parts and tooling as well as visual prototypes. When RP is used for end-use parts with interconnected moving assemblies or for producing metal casting molds which must have sufficient material for machining tolerances, accuracy is very critical. However, in general, accuracy of the finished RP parts is relatively low lll compared to parts produced by traditional manufacturing processes. The understanding of why some of these accuracy differences exist is either unknown or not …

Designing And Manufacturing Microelectronic Packages For High-Power Light-Emitting Diodes, Brian Wright, Jianbiao Pan, Richard Savage

Industrial and Manufacturing Engineering

A new microelectronic package was designed for a high-power light-emitting diode (LED). The objective was to build a package that enables the LED to operate with currents as high as 2 Amps. An innovative thin-film interface has been developed to electrically connect the cathode of the LED die to a 22AWG Cu wire. This thin-film interface is wirebondable and solderable, and consists of three layers: Au, Ni93/V7, and Si. Four 1 mil Au wirebonds, supporting 2A of maximum current, connect the Au thin-film to the LED die cathode. Sn96Ag4 solder is used for connecting the Ni93/V7 thin-film to the 22AWG …

In-House Development Of Scheduling Decision Support Systems: Case Study For Scheduling Semiconductor Device Test Operations, Tali Freed, K. H. Doerr, T. Chang

Industrial and Manufacturing Engineering

Most manufacturing processes can benefit from an automated scheduling system. However;: the design of a fast, computerised scheduling system that achieves high-quality results and requires minimal resources is a difficult undertaking. Efficient .. scheduling of a semiconductor device test facility requires an information system that provides good schedules quickly. Semiconductor device testing-is the last stage of the long semiconductor manufacturing process, and therefore. is subjected to customer service pressures. The cost of an off-the-shelf computerised scheduling system may he prohibitive for many companies. In addition, many companies are taken aback by other characteristics of off-the-shelf scheduling systems, such as code …

Fabrication Of Functionally Graded 3a/5a Zeolites By Electrophoretic Deposition, X. Wang, E. A. Olevsky, E. Bruce, M. B. Stern, D. T. Hayhurst

Industrial and Manufacturing Engineering

Functionally graded zeolites of molecular sieve type 3A and 5A are deposited by electrophoretic deposition (EPD) from acetone suspension with 8% volume concentration of n-butylamine as particle charging agent. The EPD characteristics of both 3A and 5A suspensions are studied. Functionally graded zeolite 3A/5A deposits are obtained at 200 V DC. Energy dispersive X-ray dispersion (EDX) analysis results confirm the graded structure. The deposited zeolites are also analysed by scanning electron microscopy (SEM). The factors influencing the deposition process are discussed.

The Benefits Of Automatic Data Collection In The Fresh Produce Supply Chain, Ryan Charles Panos, Tali Freed

Industrial and Manufacturing Engineering

The potential for RFID based systems to improve the safety and efficiency of a supply chain with rapidly decaying products and strict health standards is creating pressure to adopt RFID in several agricultural industries. A handful of fresh produce industry leaders currently participate in mandated pilot projects, while the industry as a whole is still intimidated by the perceived cost of RFID. Therefore in this study we attempt to validate the correlation between performance and automated data collection, paving the way to economic justification of investment in data collection technologies, such as barcode and RFID.

The majority of product in …

Case Studies On Usage Of Axiomatic Design Methodology In The U.S. Industries, Alireza Alavizadeh

All-Inclusive List of Electronic Theses and Dissertations

Axiomatic Design, originally developed by Nam Suh, is a design methodology that attempts to systematize the design practices and to provide a basis on which design can be carried out and optimized according to two main axioms, namely, Independence and Information axioms. Although various scholars in both academia and industry have studied the applicability and effectiveness of this methodology, the extent to which Axiomatic Design has been implemented in industry, particularly in the U.S., is unknown. l1l This study was conducted to identify the extent to which Axiomatic Design is known to the U.S. industries. Other purposes of this study …

Leanness And Agility In Job Shops: A Framework For A Survey Instrument Developed Using The Delphi Method, Zaki Kuruppalil

All-Inclusive List of Electronic Theses and Dissertations

Manufacturers are facing new challenges as competition has become global. Manufacturing companies arc looking for strategies which would help them gain an edge over their competitors. In the United States, lean manufacturing and agile manufacturing have been gaining importance among industries. Agile manufacturing was developed when the United States Department of Defense (DOD) requested Iacocca Institute at Lehigh University to develop a manufacturing framework that could give US companies an edge over their worldwide competitors whereas lean manufacturing has its roots tied to the Toyota Production System (TPS). This raises the questions: what is the clear difference between the two …

Fabrication Of Net-Shape Functionally Graded Composites By Electrophoretic Deposition And Sintering: Modeling And Experimentation, E.A. Olevsky, X. Wang, A. Maximenko, M.A. Meyers

Industrial and Manufacturing Engineering

It is shown that electrophoretic deposition (EPD) sintering is a technological sequence that is capable of producing net-shape bulk functionally graded materials (FGM). By controlling the shape of the deposition electrode, components of complex shapes can be obtained. To enable sintering net-shape capabilities, a novel optimization algorithm and procedure for the fabrication of net-shape functionally graded composites by EPD and sintering has been developed. The initial shape of the green specimen produced by EPD is designed in such a way that the required final shape is achieved after sintering-imposed distortions. The optimization is based on a special innovative iteration procedure …

An Experimental Evaluation Of Performance Variance For Internally Threaded Geometry Related To Extended Tap Wear In Low Carbon Steel, Todd E. Alberts

All-Inclusive List of Electronic Theses and Dissertations

The development of internal threads in a manufactured part is in many cases one of the final operations in the production workflow. Quality issues in thread form development can destroy a part that has previously undergone expensive machining. The issue of tap wear is one of the multi-faceted elements that have a direct correlation on the quality of threaded components. The purpose of this research centers on resultant mechanical pull performance for the stripping of internally threaded geometry in low carbon steel as measured over various increments of the tap cutting life cycle.

Investigation Of The Lead-Free Solder Joint Shear Performance, James Webster, Jianbiao Pan, Brian J. Toleno

Industrial and Manufacturing Engineering

Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The purpose of this study is to investigate the effects of reflow profile and thermal shock on the shear performance of eutectic SnPb (SnPb) and Sn3.0Ag0.5Cu (SAC305) solder joints. Test boards were assembled with four different sized surface mount chip resistors (1206, 0805, 0603 and 0402). Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb were developed with three levels of peak temperature (12ºC, 22ºC, and 32ºC above solder liquidus temperature, or 230ºC, 240ºC, and 250ºC for SAC …

Synthesis Of Gold Micro- And Nano-Wires By Infiltration And Thermolysis, E.A. Olevsky, X. Wang, E. Bruce, M.B. Stern, S. Wildhack, F. Aldinger

Industrial and Manufacturing Engineering

An approach for synthesizing micro- and nano-sized gold wires by infiltration and thermolysis is investigated. A porous ZrO₂ ceramic preform with aligned pores obtained by unidirectional freezing and freeze-drying is employed as an infiltration template. The sintered porous ZrO₂ preform is then infiltrated by a brushing gold solution. The thermolysis is conducted at 600 °C in air. Micro- and nano-sized gold wires are developed within the walls of the pores after thermolysis. The diameter of the gold wires ranges from several hundred nanometers to several microns.

Backward And Forward Compatibility, Jianbiao Pan, Jasbir Bath, Xiang Zhou, Dennis Willie

Industrial and Manufacturing Engineering

In response to the European Union (EU) Restriction of Hazardous Substances (RoHS) and other countries’ impending lead-free directives, the electronics industry is moving toward lead-free soldering. Total lead-free soldering requires not only lead-free solder paste but also lead-free printed circuit board (PCB) finish and lead-free component/packages. Transitioning tin-lead (SnPb) soldering to totally lead-free soldering is a complex issue and involves movement of the whole electronics industry supply chain. In reality, there is a transition period.

Correlation Of Numerical Ability And Quality Technician Best Performers In Manufacturing Quality Control Applications, Charles Wesley Shelton

All-Inclusive List of Electronic Theses and Dissertations

The occupation of Quality Technician has many duties requiring numerical operations. Business and industry place considerable emphasis on numerical ability when evaluating the performance of a Quality Technician. In this study, the numerical ability and performance classification of Quality Technicians were analyzed using a correlation analysis. lll A single case study was used to investigate this relationship. A modified Delphi Method was used to determine characteristics of a Quality Technician. Quality Technicians were evaluated by their direct supervisor and completed a standardized numerical ability test. The evaluations by the supervisor were used to classify each technician based on their performance. …

Effect Of Chromium–Gold And Titanium–Titanium Nitride–Platinum–Gold Metallization On Wire/Ribbon Bondability, Jianbiao Pan, Robert M. Pafchek, Frank F. Judd, Jason B. Baxter

Industrial and Manufacturing Engineering

Gold metallization on wafer substrates for wire/ribbon bond applications requires good bond strength to the substrate without weakening the wire/ribbon. This paper compares the ribbon bondability of Cr-Au and Ti-TiN-Pt-Au metallization systems for an optoelectronic application. Both Chromium and Titanium are used to promote adhesion between semiconductor substrates and sputtered gold films. However, both will be oxidized if they diffuse to the gold surface and result in the degradation of the wire/ribbon bondability. Restoring bondability by ceric ammonium nitrate (CAN) etch was investigated. Experiments were conducted to investigate the effect of Cr-Au and Ti-TiN-Pt-Au, annealing, and CAN etch processes, on …

Investigation Of The Lead-Free Solder Joint Shear Performance, James Webster, Jianbiao Pan, Brian J. Toleno

Industrial and Manufacturing Engineering

Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The purpose of this study is to investigate the effects of reflow profile and thermal shock on the shear performance of eutectic SnPb (SnPb) and Sn3.0Ag0.5Cu (SAC305) solder joints. Test boards were assembled with four different sized surface mount chip resistors (1206, 0805, 0603 and 0402). Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb were developed with three levels of peak temperature (12ºC, 22ºC, and 32ºC above solder liquidus temperature, or 230ºC, 240ºC, and 250ºC for SAC …

Estimation Of Liquidus Temperature When Snagcu Bga/Csp Components Are Soldered With Snpb Paste, Jianbiao Pan

Industrial and Manufacturing Engineering

Recently, the soldering of lead-free components with SnPb paste, or lead-free backward compatibility, is becoming a hot topic. One of the major challenges in backward compatibility assembly is the development of a right reflow profile for the soldering of SnAgCu Ball Grid Array (BGA)/Chip Scale Package (CSP) components with SnPb paste. If the SnAgCu reflow profile is used, the reflow temperature may be too high for other SnPb components in the same board during assembly according to the component rating per IPC/JEDEC J-STD-020C. In addition, the flux in SnPb solder paste may not function properly in such a high reflow …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

A Comparative Study Of Various Loss Functions In The Economic Tolerance Design, Jehnan Pan, Jianbiao Pan

Industrial and Manufacturing Engineering

Engineering tolerance design plays an important role in modern manufacturing. In this paper, the Kapur's model was modified so that the economic specification limits for both symmetric and asymmetric losses can be established. Three different loss functions: (1) Taguchi's quadratic loss function; (2) Inverted Normal Loss Function; (3) Revised Inverted Normal Loss Function are compared in the economic tolerance design. The relationships between the three loss functions and process capability indices for symmetric tolerance are established. The results suggest that the revised inverted normal loss function be used in determination of economic specification limits.

Plotting A Bright Future For Manufacturing Education: Results Of A Brainstorming Session, Daniel Waldorf, Sema E. Alptekin, Robert Bjurman

Industrial and Manufacturing Engineering

Manufacturing industries worldwide have undergone dramatic changes in recent years and now demand more from graduating manufacturing engineers. The effects of globalization have forever changed the parameters for success in manufacturing. Our educational institutions must respond to these changes with innovation. That agenda formed the basis for a special SME/CIRP international conference on manufacturing engineering education called “Looking Forward: Innovations in Manufacturing Engineering Education,” held in San Luis Obispo, California, June 22-25, 2005. At the meeting, manufacturing education professionals from around the world came together to share their own innovative ideas and to brainstorm ways to shape the future of …

Measuring Plant-Wide Energy Savings, J. Kelly Kissock, Carl Eger

Mechanical and Aerospace Engineering Faculty Publications

This paper presents a general method for measuring plant-wide industrial energy savings and demonstrates the method using a case study from an actual industrial energy assessment. The method uses regression models to characterize baseline energy use. It takes into account changes in weather and production, and can use sub-metered data or whole plant utility billing data. In addition to calculating overall savings, the method is also able to disaggregate savings into components, which provides additional insight into the effectiveness of the individual savings measures.

Although the method incorporates search techniques and multi-variable least-squares regression, it is easily implemented using data …

Processing Model For Tungsten Powders And Extention To Nanoscale Size Range, Randall M. German, J. Ma, X. Wang, E. Olevsky

Industrial and Manufacturing Engineering

Nanoscale tungsten powders promise access to very hard, strong and wear resistant materials via the press–sinter route. A small particle size changes the response during sintering, requiring lower temperatures and shorter times to attain dense but small grain size structures. On the other hand, oxide reduction and impurity evaporation favour high sintering temperatures and long hold times. Accordingly, press–sinter processing encounters conflicting constraints when applied to small particles. Presented here is an analysis of press–sinter tungsten particle processing to isolate conditions that balance the temperature and size dependent effects. The calculations are pinned by existing data. Opportunities are identified for …

The Effect Of Reflow Profile On Snpb And Snagcu Solder Joint Shear Strength, Jianbiao Pan, Brian J. Toleno, Tzu-Chien Chou, Wesley J. Dee

Industrial and Manufacturing Engineering

Purpose –The purpose of this work is to study the effect of the reflow peak temperature and time above liquidus on both SnPb and SnAgCu solder joint shear strength.

Design/methodology/approach –Nine reflow profiles for Sn3.0Ag0.5Cu and nine reflow profiles for Sn37Pb have been developed with three levels of peak temperature (230°C, 240°C, and 250°C for Sn3.0Ag0.5Cu; and 195°C, 205°C, and 215°C for Sn37Pb) and three levels of time above solder liquidus temperature (30, 60, and 90 s). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different …

A Simplified Model For Ploughing Forces In Turning, Daniel Waldorf

Industrial and Manufacturing Engineering

This paper aims to provide experimental data in support of a modified theoretical model for quantifying the effect of cutting tool edge geometry on machining forces. A previously published slip-line model is simplified and extended to the case of turning. Several sets of machining experiments were run with custom-fabricated cutting inserts of varying edge hone radius and chamfer geometry. Cutting forces were measured using a dynamometer during cutting. Results show that varying edge geometry can have a major effect on cutting forces. The developed model effectively captures the edge phenomenon and its effect on cutting forces and also offers a …

Support For A Delivery Train Based Material Handling Mechanism, Sai P. Boyedapu

Electrical & Computer Engineering Theses & Dissertations

Modeling a delivery train system is more challenging than traditional forklift systems as the delivery train model consists of a tugger, cart and a controller that combine to deliver materials within a manufacturing plant. Also, the decision logic for selection of carts and tuggers, joining of loads to particular delivery trains is more complicated than forklift systems. Simulation software such as Arena, Automod and Flexsim do not provide direct support for modeling delivery train systems.

In this thesis, an object-oriented, platform and language independent model of a delivery train was designed. The model was then implemented as an extension to …