Operations Research, Systems Engineering and Industrial Engineering Commons^™

Effect Of Overhead Drilling Support On Muscular Activity Of Shoulder, Bharat Kumar Bhogaraju Bhallam Venkata

LSU Master's Theses

This study examines the effect of an overhead drilling support and position of the arm on muscular activity of the shoulder. Five male participants simulated an overhead drilling task by using a drill in near, middle and far reach positions. Electromyographic measurements were taken from the dominant side anterior deltoid, bicep and trapezius muscles. Root mean square amplitude (RMS) of the EMG activity from these muscles was used to determine the load on the muscular system. The participants used a subjective rating scale to evaluate the overhead support stand and holding position. The results demonstrate that the overhead support stand …

Effect Of Repetitions On Static And Dynamic Strength, Sai Chaitanya Reddy Bogolu

LSU Master's Theses

The objective of this study was to investigate the effect of repetitions on static and dynamic strength. The study is divided into two parts, the first part investigated static and dynamic strength during one, three and six repetitions per minute, and the second part of the study analyzed dynamic strength data collected using the Multiaxial Multipurpose Isokinetic Dynamometer. The study comprised of dynamic strength test data at three speeds of one, five and ten inch per second. Five male subjects participated in the first part of the study, and the results were analyzed by plotting a time series to observe …

Balancing Mixed-Model Assembly Line To Reduce Work Overload In A Multi-Level Production System, Pravin Y. Tambe

LSU Master's Theses

Generating the optimal production schedule for an assembly line, which will balance the workload at all the production stages, is a difficult task considering a variety of practical constraints. Varying customer demand is an important factor to be considered when designing an assembly line. In order to respond to varying customer demand, many companies are attempting to make their production system more flexible/agile or adaptable to change. Due to the volatile nature of market, companies cannot afford to manufacture same type of product for long period of time and neither can maintain high inventory level; to tackle this problem we …

Employee Commitment And Turnover: Literature And Data Analysis Of Correlations, Jean-Paul M. Arnaout, Gamze Karayaz, Andres Sousa-Poza

Engineering Management & Systems Engineering Faculty Publications

Due to the current turbulent environment, companies had to evolve form their traditional rigid structures to flexible and efficient ones, in order to better adapt to the continuous changes in the environment. New practices have emerged in the workplace, particularly the large layoffs of employees due to budget cuts, leading to an increase in the organizations' turnover. Thus, in today's world, a company is subject to high turnovers at any time of its life cycle; a suggested approach for reducing this turnover is through the improvement of organizational commitment. This paper addresses the following question: "Do all forms of employee …

A Dyadic Composition To Foster Virtual Team Effectiveness: An Experimental Study, Gamze Karayaz

Engineering Management & Systems Engineering Theses & Dissertations

The importance of effectiveness for virtual teamwork continues to gain momentum as technology and globalization of work accelerate. The implementation of virtual teams provides one approach to enhance competitiveness, overcoming the disadvantages of space and time differences through collaborative technologies. The influence of structure to virtual team performance has not been clearly established in the literature. The purpose of this research study was to investigate the effectiveness of a dyad structured approach for virtual teams using a quasi-experimental research design.

This research investigated four questions related to the influence of structure on virtual team effectiveness related to task performance, communication …

Assimilating Non-Probabilistic Assessments Of The Estimation Of Uncertainty Bias In Expert Judgment Elicitation Using An Evidence Based Approach In High Consequence Conceptual Designs, Colin K. S. Barrows

Engineering Management & Systems Engineering Theses & Dissertations

One of the major challenges in conceptual designs of complex systems is the identification of uncertainty embedded in the information due to lack of historic data. This becomes of increased concern especially in high-risk industries. This document reports a developed methodology that allows for the cognitive bias, estimation of uncertainty, to be elucidated to improve the quality of elicited data. It consists of a comprehensive literature review that begins by defining a 'High Consequence Conceptual Engineering Environment' and identifies the high-risk industries in which these environments are found. It proceeds with a discussion that differentiates risk and uncertainty in decision-making …

A Robust Reactive Scheduling System With Application To Parallel Machine Scheduling, Jean-Paul M. Arnaout

Engineering Management & Systems Engineering Theses & Dissertations

In this turbulent world, scheduling role has become crucial in most manufacturing production, and service systems. It allows the allocation of limited resources to activities with the objective of optimizing one performance measure or more. Resources may be machines in a factory, operating rooms in a hospital, or employees in a company, while activities can be jobs in a manufacturing plant, surgeries in a hospital, or paper work in a company. The goal of each schedule is to optimize some performance measures, which could be the minimization of the schedule makespan, the jobs' completion times, jobs' earliness and tardiness, among …

Requirements Gathering For Simulation, John Ryan, Cathal Heavey

Conference papers

This paper discusses the current shortfalls in support for the pre-coding phases of a discrete event simulation project. The paper then presents a process modelling technique, Simulation Activity Diagrams (SADs), developed to specifically support the initial requirements gathering phases of a simulation project. The paper concludes with an outline of proposed future developments to the modelling technique.

Engineering Education Through Service-Learning In Developing Communities: Two Case Studies, Evan A. Thomas, Andrew Azman

Mechanical and Materials Engineering Faculty Publications and Presentations

This paper provides case studies of two service learning projects that University of Colorado at Boulder (CU-Boulder) students are integrating into their academic experience. The projects focus on developing communities and are managed under the auspices of Engineers Without Borders-USA (EWB-USA), a group founded by Dr. Bernard Amadei, Professor of Civil Engineering at CU-Boulder. These projects expand students? understanding of the social value of their chosen profession, and expose them to a type of engineering significantly different than what is presented in most of their classes. Specifically, focusing on developing communities provides students with the opportunity to design solutions to …

Effects Of The Use Of Soybean Oil As Cutting Fluid On The Surface Finish For Turning Operations, Carlos Alberto TeráN Yengle

Dissertations and Theses @ UNI

Concerns about the long term supply of petroleum, the instability of its prices, and growing environmental issues have led to a variety of legislative and public support for the use of agricultural commodities in industrial applications. This study is of importance because of environmental and health hazards concerns, and the possibility of reducing operating costs with the elimination of disposal of used cutting oil that the use of biodegradable oil offers to the metal-cutting operations.

The purpose of this study was to investigate the effect of the use of an experimental soybean-based oil as a cutting fluid on surface finish …

An Investigation Into Microwave Energy To Soften Scrap Tire Rubber Aiding Existing Mechanical Separation Processes, Russell Jon Lucas

Dissertations and Theses @ UNI

This research was performed to soften scrap tires to aid in their transformation from whole tires to valuable streams of rubber and steel for reuse in industry. Actual shredded scrap rubber was used in this experiment to determine if this highly variable material could yield consistent results if subjected to volumetric heating from a magnetron emitting microwave energy.

A consumer microwave oven was used to heat this material. This oven had its control circuitry modified by using a programmable logic controller to operate the energy exposure time. The sample's surface temperature was measured utilizing a non contact infrared thermometer. All …

Imse Alumni Survey Of Abet Program Educational Objectives, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

This report showcases the results of the Department of Industrial and Management System Engieering's survey of alumni regarding our updated ABET Program Educational Objectives. The Program Educational Objectives represent the expected characteristics of industrial engineering graduates within three to five years of receiving a Bachelor of Science degree in Industrial and Management Systems Engineering from the University of Nebraska-Lincoln. A total of 76 responses were received. The alumni survey responses indicate strong agreement and approval for the new Program Educational Objectives. The associated comments will be used by the IMSE faculty to future refine the course curriculum to ensure that …

A Template-Based Data Specification Framework For Modeling Physical Security Systems, Ashu Guru, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

Simulation studies often fail to provide any useful results due to its success being highly dependent on the skills of the analyst to understand a system and then correctly identify all the required data parameters and dependent variables. This paper describes a template-based framework to help identify and specify the components and data parameters for developing models of physical security systems. The layered framework consists of fifteen templates built on top of fourteen data primitives representing 119 data parameters. The modeling framework has been programmed as an internet-based web application and is simulation language independent. The usefulness of the framework …

Adaptive And Probabilistic Power Control Algorithms For Dense Rfid Reader Network, Kainan Cha, Anil Ramachandran, Jagannathan Sarangapani

Electrical and Computer Engineering Faculty Research & Creative Works

In radio frequency identification (RFID) systems, the detection range and read rates may suffer from interferences between high power devices such as readers. In dense networks, this problem grows severely and degrades system performance. In this paper, we investigate feasible power control schemes to ensure overall coverage area of the system while maintaining a desired data rate. The power control should dynamically adjust the output power of a RFID reader by adapting to the noise level seen during tag reading and acceptable signal-to-noise ratio (SNR). We present a novel distributed adaptive power control (DAPC) and probabilistic power control (PPC) as …

Adaptive Distributed Fair Scheduling And Its Implementation In Wireless Sensor Networks, Maciej Jan Zawodniok, Jagannathan Sarangapani, Steve Eugene Watkins, James W. Fonda

Electrical and Computer Engineering Faculty Research & Creative Works

A novel adaptive and distributed fair scheduling (ADFS) scheme for wireless sensor networks is shown through hardware implementation. In contrast to simulation, hardware evaluation provides valuable feedback to protocol and hardware development process. The proposed protocol focuses on quality-of-service (QoS) issues to address flow prioritization. Thus, when nodes access a shared channel, the proposed ADFS allocates the channel bandwidth proportionally to the weight, or priority, of the packet flows. Moreover, ADFS allows for dynamic allocation of network resources with little added overhead. Weights are initially assigned using user specified QoS criteria. These weights are subsequently updated as a function of …

Decentralized Power Control With Implementation For Rfid Networks, Kainan Cha, Anil Ramachandran, David Pommerenke, Jagannathan Sarangapani

Electrical and Computer Engineering Faculty Research & Creative Works

In radio frequency identification (RFID) systems, the detection range and read rates will suffer from interference among high power reading devices. This problem grows severely and degrades system performance in dense RFID networks. In this paper, we investigate a suite of feasible power control schemes to ensure overall coverage area of the system while maintaining a desired read rate. The power control scheme and MAC protocol dynamically adjusts the RFID reader power output in response to the interference level seen locally during tag reading for an acceptable signal-to-noise ratio (SNR). We present novel distributed adaptive power control (DAPC) and probabilistic …

Development And Implementation Of Optimized Energy-Delay Sub-Network Routing Protocol For Wireless Sensor Networks, Maciej Jan Zawodniok, Jagannathan Sarangapani, Steve Eugene Watkins, James W. Fonda

Electrical and Computer Engineering Faculty Research & Creative Works

The development and implementation of the optimized energy-delay sub-network routing (OEDSR) protocol for wireless sensor networks (WSN) is presented. This ondemand routing protocol minimizes a novel link cost factor which is defined using available energy, end-to-end (E2E) delay and distance from a node to the base station (BS), along with clustering, to effectively route information to the BS. Initially, the nodes are either in idle or sleep mode, but once an event is detected, the nodes near the event become active and start forming sub-networks. Formation of the inactive network into a sub-network saves energy because only a portion of …

Distributed Power Control For Cellular Networks In The Presence Of Channel Uncertainties, Maciej Jan Zawodniok, Q. Shang, Jagannathan Sarangapani

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, a novel distributed power control (DPC) scheme for cellular network in the presence of radio channel uncertainties such as path loss, shadowing, and Rayleigh fading is presented. Since these uncertainties can attenuate the received signal strength and can cause variations in the received Signal-to-Interference ratio (SIR), a new DPC scheme, which can estimate the slowly varying channel uncertainty, is proposed so that a target SIR at the receiver can be maintained. Further, the standard assumption of a constant interference during a link's power update used in other works in the literature is relaxed. A CDMA-based cellular network …

Neural Network-Based Output Feedback Controller For Lean Operation Of Spark Ignition Engines, Brian C. Kaul, Jagannathan Sarangapani, J. A. Drallmeier, Jonathan B. Vance, Pingan He

Electrical and Computer Engineering Faculty Research & Creative Works

Spark ignition (SI) engines running at very lean conditions demonstrate significant nonlinear behavior by exhibiting cycle-to-cycle dispersion of heat release even though such operation can significantly reduce NOx emissions and improve fuel efficiency by as much as 5-10%. A suite of neural network (NN) controller without and with reinforcement learning employing output feedback has shown ability to reduce the nonlinear cyclic dispersion observed under lean operating conditions. The neural network controllers consists of three NN: a) A NN observer to estimate the states of the engine such as total fuel and air; b) a second NN for generating virtual input; …

Neuro Control Of Nonlinear Discrete Time Systems With Deadzone And Input Constraints, Pingan He, Wenzhi Gao, Jagannathan Sarangapani

Electrical and Computer Engineering Faculty Research & Creative Works

A neural network (NN) controller in discrete time is designed to deliver a desired tracking performance for a class of uncertain nonlinear systems with unknown deadzones and magnitude constraints on the input. The NN controller consists of two NNs: the first NN for compensating the unknown deadzones; and the second NN for compensating the uncertain nonlinear system dynamics. The magnitude constraints on the input are modeled as saturation nonlinearities and they are dealt with in the Lyapunov-based controller design. The uniformly ultimate boundedness (UUB) of the closed-loop tracking errors and the neural network weights estimation errors is demonstrated via Lyapunov …

Forecasting Using The Mahalanobis-Taguchi System In The Presence Of Collinearity, Elizabeth A. Cudney, Kenneth M. Ragsdell

Engineering Management and Systems Engineering Faculty Research & Creative Works

The Mahalanobis Taguchi System is a diagnosis and forecasting method for multivariate data. Mahalanobis distance is a measure based on correlations between the variables and different patterns that can be identified and analyzed with respect to a base or reference group. the issue of multicollinearity is not adequately addressed in the MTS method. in cases where strong relationships exist between variables, the correlation matrix becomes almost singular, and the inverse matrix is not accurate. Multicollinearity can be handled by utilizing the adjoint matrix of the correlation matrix and Gram-Schmidt orthogonalization. This paper presents a case study of the MTS methodology …

Heuristics And Genetic Algorithms, Michael D. Mobley, Cihan H. Dagli, David Enke

Engineering Management and Systems Engineering Faculty Research & Creative Works

Genetic algorithms are design tools used in generating optimal solutions. While they can often be shown to outperform various heuristic methods and hybrid approaches, using a combination of evolutionary algorithms and heuristic approaches can generate an optimal solution more quickly than either of the two methods independently. Our purpose is to provide an overview of genetic algorithms, to discuss the types of problems that lend themselves to being solved by genetic algorithms, and to identify heuristics that have been shown to aid genetic algorithms in their quest for optimal solutions. While the sample problems discussed in this paper are generally …

Unifying Value Methodology And Robust Design To Achieve Design For Six Sigma, Vivek K. Jikar, Elizabeth A. Cudney, Kenneth M. Ragsdell, Chuck T. Hui

Engineering Management and Systems Engineering Faculty Research & Creative Works

The concept of product or system function is considered as described in the Taguchi System of Quality Engineering. the importance of transfer functions is also discussed, and a review of conventional value analysis techniques is given. This paper proposes a combination of the principles of robust design and value methodology to enable on-target functionality and direct cost allocation early in the product development process. the discussion on integration of value analysis principles in robust design methodology is provided considering the six-sigma environment. Copyright © 2006 SAE International.

Applying The Mahalanobis-Taguchi System To Vehicle Handling, Kioumars Paryani, Elizabeth A. Cudney, K. M. Ragsdell

Engineering Management and Systems Engineering Faculty Research & Creative Works

The Mahalanobis-Taguchi system (MTS) is a diagnosis and forecasting method using multivariate data. Mahalanobis distance (MD) is a measure based on correlations between the variables and patterns that can be identified and analyzed with respect to a base or reference group. The MTS is of interest because of its reported accuracy in forecasting using small, correlated data sets. This is the type of data that is encountered with consumer vehicle ratings. MTS enables a reduction in dimensionality and the ability to develop a scale based on MD values. MTS identifies a set of useful variables from the complete data set …

A Methodology For Deriving System Requirements Using Agent Based System Modeling, Karthik Gopalakrishnan, Sreeram Ramakrishnan, Cihan H. Dagli

Engineering Management and Systems Engineering Faculty Research & Creative Works

In this paper, we duscuss a method to derive the requirements for developing an Industrial Automation and Constrol System (IACS). An IACS has software components and associated hardware, which together implement the required monitoring, supervision and control of operations an a production plant. The requirements of such a system are multi-dimensional and may require multiple layers of abstraction. For this domain, we propose an agent-based modeling adopting an agent-based modeling approach is the implicit flexibility afforded by agents and the negotiation techniques that can be implemented to streamline the change management process associated with requirements modeling and analysis. This paper …

A Simulation Framework For Real-Time Management And Control Of Inventory Routing Decisions, Shrikant Jarugumilli, Sreeram Ramakrishnan, Scott Erwin Grasman

Engineering Management and Systems Engineering Faculty Research & Creative Works

We consider a logistics network where a single warehouse distributes a single item to multiple retailers. Retailers in the network participate in a Vendor Managed Inventory (VMI) program with the warehouse, where the warehouse is responsible for tracking and replenishing the inventory at various retailer locations. The information update occurs every time a vehicle reaches a location and the decision on the delivery quantity and the next location to visit is made. For a small increase of locations in the network, the state space for the solution increases exponentially, making this problem NP-hard. Thus, we propose a solution methodology where …

Modeling Net-Centric System Of Systems Using The Dystems Modeling Language Sysml, Rao Madwaraj, Sreeram Ramakrishnan, Cihan H. Dagli

Engineering Management and Systems Engineering Faculty Research & Creative Works

Understanding the operations of a large 'net-centric system-of-systems requires in-depth knowledge of the interfaces among the various systems, sub-systems and components. Architectural modeling can help in reducing the complexity involved in designing such large networked systems. An example of such a complex system is the Global Earth Observation System of Systems (GEOSS) - a system for monitoring and collecting information related to Earth's resources. This paper demonstrates the use of Systems Modeling Language (SysML), which supports specification, analysis, design, verification and validation of a broad range of complex systems, to model some aspects of the GEOSS. The paper discusses issues …

Multiagent Teamwork: Hybrid Approaches, Praveen Paruchuri, Emma Bowring, Ranjit Nair, Jonathan Pearce, Nathan Schurr, Milind Tambe, Pradeep Varakantham

Research Collection School Of Computing and Information Systems

Today within the multiagent community, we see at least four competing methods to building multiagent systems: beliefdesireintention (BDI), distributed constraint optimization (DCOP), distributed POMDPs, and auctions or game-theoretic methods. While there is exciting progress within each approach, there is a lack of cross-cutting research. This article highlights the various hybrid techniques for multiagent teamwork developed by the teamcore group. In particular, for the past decade, the TEAMCORE research group has focused on building agent teams in complex, dynamic domains. While our early work was inspired by BDI, we will present an overview of recent research that uses DCOPs and distributed …

Visualization For Analyzing Trajectory-Based Metaheuristic Search Algorithms, Steven Halim, Roland H. C. Yap, Hoong Chuin Lau

Research Collection School Of Computing and Information Systems

No abstract provided.

Evaluation Of The Effect Of Vehicle Performance On Consumer Satisfaction, Elizabeth A. Cudney

Doctoral Dissertations

"Value is the relationship of functionality or benefit to the cost of a product or service. Consumers appear to seek value, but not all consumers are alike in their needs and wants. Common characteristics that consumers desire in automobiles include a high level of value relative to the product's cost. Consumers measure vehicle performance in terms of twenty-three attributes such as roominess, ride, reliability, handling, brake pedal feel, visibility, interior noise, acceleration, etc. Problems arise when automakers try to translate these characteristics into vehicle performance specifications and capabilities.

Quality is an essential element for both the consumer and producer since …