Operations Research, Systems Engineering and Industrial Engineering Commons^™

From The Desk Of The Editor

Journal of International Technology and Information Management

No abstract provided.

Table Of Contents

Journal of International Technology and Information Management

No abstract provided.

From The Desk Of The Editor

Journal of International Technology and Information Management

No abstract provided.

Current Barriers To Successful Implementation Of Fist Principles, Brandon Keller, Joseph R. Wirthlin

Faculty Publications

The Fast, Inexpensive, Simple, and Tiny (FIST) framework proposes a broad set of organizational values, but provides limited guidance on practical implementation. Implementing FIST principles requires clarifying the definitions of “fast,” “inexpensive,” and “simple,” recognizing where FIST does and does not apply. Additionally, a subset of the FIST heuristics was expanded upon to increase their usefulness for practitioners. The primary research findings are that FIST principles are less conducive for highly complex or novel systems, immature technologies, future needs, acquisitions in early development phases, or when performance is the foremost value. FIST principles were also found to be constrained by …

Innovation Measurement: A Decision Framework To Determine Innovativeness Of A Company, Kenny Phan

Dissertations and Theses

Innovation is one of the most important sources of competitive advantage. It helps a company to fuel the growth of new products and services, sustain incumbents, create new markets, transform industries, and promote the global competitiveness of nations. Because of its importance, companies need to manage innovation. It is very important for a company to be able to measure its innovativeness because one cannot effectively manage without measurement. A good measurement model will help a company to understand its current capability and identify areas that need improvement.

In this research a systematic approach was developed for a company to measure …

Sustainability In Industrial Logistics Operations, Vishnu Siddharth Somanur Paramasivam

Purdue Polytechnic Directed Projects

CO2 concentration in the atmosphere has been rising at a rapid rate. As per the numbers quoted, the concentration has surpassed the safest upper limit suggested by the scientists. CO2 is a green-house gas and is partially responsible for global warming. With the current rate of emissions, it poses a threat to the planet's future and prosperity. Transportation contributes 30% of the overall CO2 emissions. Companies that use transportation are taking sustainability initiatives to reduce the emissions. This project documented some of the sustainability practices followed by the companies currently. It was found that the practices followed three general methods …

Dynamics Capabilities, Caroline Mudavadi, Farshad Madani, Garrett Gilliland, Corey White

Engineering and Technology Management Student Projects

Slides from a presentation based on Teece, D. J. (January 01, 2007). Explicating dynamic capabilities: the nature and microfoundations of (sustainable) enterprise performance. Strategic Management Journal, 28, 13, 1319.

Discusses capabilities that enable business enterprises to create, deploy, and protect the intangible assets that support superior long-run business performance.

Design And Implementation Of Erp Software In Material Supply Chain Management For Siix Corp., Xing'er Chen

World Maritime University Dissertations

No abstract provided.

Case Study: The Optimization Of Information Flow & Organization In Software Development, Farshad Madani, Bing Wang, Xiaowen Wang, Corey White, Liying Wang

Engineering and Technology Management Student Projects

Trial and error are inevitable in the process of software development; the redesign is wasteful when unfocused communication occurs within the development process. To speed up this development process, we optimized the information flow and redesigned the development organization into chunks. First, we investigated the information flow between tasks and coupled tasks into phases utilizing the Design Structure Matrix (DSM) so that the information exchange among chunks of tasks is as few as possible. In this way, the redundant iterations of tasks are eliminated. Meanwhile, we also grouped the engineers into groups according to the tasks, in this; we eliminated …

Blunt Impact Performance Evaluation Of Helmet Lining Systems For Military And Recreational Use, Jaclyn Siniora, Ryan Taylor, Darren Suey

Industrial Technology and Packaging

With the increasing problem in collegiate athletes experiencing injuries to the brain, different helmet liners where put to the test to see which liner provided athletes the greatest protection under specific conditions.

This senior project evaluates five different liners in football helmets. Each of the helmet liners were tested at three different temperatures: hot, cold, and ambient. Each helmet had seven different impact locations which were put to the test. The project was designed to be used to test ACH military combat liners as well. Due to shipping bottle necks the ACH combat liners have been left to future Cal …

Application Of Intelligent-Objects Simulation To Manufacturing Process Efficiency Analysis: A Case Study, Justin Hamilton

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science and Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Justin Hamilton on May 12, 2012.

Patent Analysis For Smart Grid Development In The U.S, Abrahim Abdulsater, Bahareh Saatchi, Farshad Madani

Engineering and Technology Management Student Projects

By increasing demand for energy among nations the rate of fossil fuel consumption is boosting. The raise of fossil fuel consumption has motivated nations to gain some capabilities for the purpose of dealing with some consequences; the more fossil fuel consumption, the higher price for energy, and the higher rate of GHG as well. Recently smart grid technology has been introduced as a healing approach in terms of using energy more efficiently. This study made an effort to have some discussions around smart grid technology development in the United States by patent analysis and forecasting. The outcomes in both technology …

Application Of Reference Models In Technology Management, Farshad Madani

Engineering and Technology Management Student Projects

Reference models, sometimes called with other different words, prepare a general model from a specific view of the related environment. Reference models are considered as a basic foundation to create: 1) a common language among specialists 2) a reference for the entities such as processes 3) relationships among entities 4) tools and decision making procedures for the real world.

In this report, it's tried the definitions of reference model in the selected papers have been reviewed. It's noticeable that in many papers the term of framework is used instead of reference model. Also, applications of reference models are reviewed and …

Factors Impacting Technology Transfer: The Maquiladora Industry In Yucatan, Mexico, Ana Maria Canto, Carlos Blanco, Pilar Pazos

Engineering Management & Systems Engineering Faculty Publications

Technology transfer and knowledge transfer are the building blocks for innovation, efficiency and increased competitiveness. The topic of technology transfer in the context of multinational companies has been the focus of technology management researchers for well over two decades. Developing countries housing twin plans have been exposed to technology transfer from very diverse countries with different approaches to the technology transfer process and different levels of success. This cultural and national diversity adds an additional level of complexity to the technology transfer domain that has been largely unexplored. This paper will explore critical factors that had an impact in successful …

Creating A State-Wide Transfer Program For Engineering Technology And Technology Management Studies, Gregory Arbuckle, Mark Doggett

SEAS Faculty Publications

The primary purpose of the Western Kentucky Pipeline for 2+2+2 Engineering Technology and Technology Management (ET/TM) students program is to significantly increase degree production and workforce preparation in central and western Kentucky through the construction of a long-term sustainable, reproducible model bridging program of cooperation between Western Kentucky University (WKU), Murray State University (MSU) and the Kentucky Community and Technical College System (KCTCS). The program will significantly increase industrial and technology education opportunities, technology enrollment and two and four-year degree completion. Additionally, this project supports the Kentucky Council on Postsecondary Education’s (CPE) goal to double the overall number of undergraduate …

An Unstable Balance: Exploration, Exploitation, And Innovation Decline During Development, Craig Randall

2012

he ability to innovate is considered central to firm performance and the consensus is that firms should balance exploration and exploitation innovation to succeed. Studies using an exploration/exploitation perspective have gained increasing interest, and have generally concluded that exploration innovation rates are too low. Researchers have concentrated on the early aspects of the innovation planning process: the Search, Portfolio Selection, and Design Phase, and have also studied the benefits of pursuing a serial or parallel pursuit of exploration and exploitation. Largely missing from exploration/exploitation innovation literature, however, is the development phase—which is among the longest and resource intensive phases of …

Partial Budgeting Analysis Of Conventional Pump Over Versus Pulsair Cap Management System For A Large–Scale California Winery, Zachary Thomas Hicks

Agribusiness

The purpose of this project was to evaluate the financial feasibility of implementing an automated gas injection system from Pulsair as an alternative to the traditional pump over cap mixing technique that is used during the alcoholic fermentation stage of winemaking.

There were various costs involved in this project that were determined and explained through the use of the partial budgeting method. The costs that were thoroughly analyzed included equipment, labor, utility, and initial investment costs for the Pulsair system as well as the related pump over operation costs. After the two methods associated numbers were evaluated, they were then …

The Impact Of 3pl’S Green Initiatives On The Purchasing Of Transport And Logistics Services: An Exploratory Study, Pietro Evangelista, Maria Huge-Brodin, Karin Isaksson, Edward Sweeney

Conference papers

There is a lack of research investigating the interaction and reciprocal influences between the buyer perspective and the supplier of transport and logistics services. Studies on the buyer perspective analyse the selection criteria to buy 3PL services, while research focused on green 3PL services examine initiatives undertaken by these companies to provide more environmentally sustainable services. The objective of this paper is to fill this void through an explorative case study analysis on the environmental attitude of 3PL companies in order to derive relevant implications for buyer’s behaviour. The results provide useful guidelines to buyers for understanding awareness, initiatives as …

Toward A Technology Management Core: Defining What The Technology Manager Needs To Know, Mark Doggett, Pam Mcgee, Sophia Scott

SEAS Faculty Publications

With the increasing demands on organizations to do “more with less,” and produce acceptable market results, productivity and performance standards continually raise the expectations on competitive success. To meet these expectations, organizations should create learning opportunities that combine the application of technical management skills along with the softer skills involved in people management. Technical managers with little training or past experience with nontechnical skills often perform poorly in technical management positions (Kroecker, 2007). Because this generation lives in a highly technical environment, managers need to be proficient in dealing with knowledge workers and systems; therefore, there is a growing emphasis …

Gerber Project For Lockheed Martin, Andrew Callahan, Sean Lawyer

Industrial Technology and Packaging

Lockheed Martin, the world’s premier aerial combat vehicle manufacturer was pressed to find an eco-friendly way to package their impregnated epoxy. In the current system, the epoxy would be cut on the Gerber table to a pre-determined length and then sandwiched inside of two corrugated fiberboard sheets for storage inside of a freezer. The current process was not only labor intensive, but the corrugated fiberboard had to be disregarded after one use. In conjunction with the Cal Poly San Luis Obispo Packaging program and Melmat Incorporated, we were able to find a corrugated plastic substrate to replace the currently non-reusable …

Towards A Center For Modeling And Simulation: The Case For Jordan, Ghaith Rabadi, Hazem Kaylani, Joseph Barjis (Ed.), Murali Mohan Narasipuram (Ed.), Ghaith Rabadi (Ed.), Jolita Ralyt (Ed.), Pierluigi Plebani (Ed.)

Engineering Management & Systems Engineering Faculty Publications

Modeling and Simulation (M&S) has recently become an important area that is pursued by many researchers and practitioners due to the role it plays in understanding complex systems and problems. We have therefore witnessed the establishment of many M&S organizations in the last two decades especially in the more developed world. Less developed countries are starting to recognize the need for such capability especially that the problems they face are not less complex. In this paper, we present a preliminary study towards a business plan for establishing a scientific center for Modeling, Analysis, Simulation and Animation in Jordan (JoSAMA) and …

The Impact Of Task Conflict On Virtual Team Performance And Cohesiveness, Wilawan Onkman, Anil Ustun, Pilar Pazos, Ana Maria Canto

Engineering Management & Systems Engineering Faculty Publications

This paper examined the impact of task conflict on team performance and cohesiveness. Twelve virtual teams participated in two sessions with two difficulty levels. Each task consisted of a survival simulation. Teams communicated using a text-based communication media (chat). A mixed methods approach combining both quantitative and qualitative data was used. Performance was measured using expert ratings, and cohesiveness was measured using a modified version of Seashore's Cohesiveness Index. Content analysis was utilized to evaluate the level of task conflict on the team. This study provides some initial evidence on the effects task conflict on virtual team performance.

Simpler Packaging, Tomiko Oden

Graphic Communication

This project explains how product packaging is become more "green", and thus more simple. Packaging needs to go beyond just simplifying materials and graphics - it needs to create a simpler process in order to reduce wasted time, energy, and resources.

Measurement And Analysis Of Shocks To Products Packaged In Pails In Single Parcel Ground Shipments, Sher Paul Singh, Jay Singh, Pakapol Kittipinyovath

Industrial Technology and Packaging

The objective of this study was to measure and analyse the shocks and impacts experienced by pails in the single parcel distribution environment, with and without a secondary corrugated shipper. The study was conducted in the FedEx Ground shipping environment in the USA. Instrumented 5 gal pails were shipped with and without an outer corrugated box, and with and without handling (precautionary warning) labels, from East Lansing, Michigan to destinations in California and New York. Data recorders were used to collect and analyse shock distribution data (drop heights, drop orientations and number of drops). The results showed that the precautionary …

Automated Fixture Design For A Rapid Machining Process, Wutthigrai Boonsuk, Matthew C. Frank

Faculty Research & Creative Activity

Rapid prototyping techniques for CNC machining have been developed in an effort to produce functional prototypes in appropriate materials. One of the major challenges for rapid machining is to develop an automatic fixturing system for securing the part during the machining process. The method proposed in this paper is the use of sacrificial fixturing, similar to the support structures in existing rapid processes like Stereolithography. During the machining process, sacrificial supports emerge incrementally and, at the end of the process, are the only entities connecting the part to the stock material. This paper presents methodologies for the design of sacrificial …

Automated Fixture Design For A Rapid Machining Process, Wutthigrai Boonsuk, Matthew Frank

Faculty Research & Creative Activity

Rapid prototyping techniques for CNC machining have been developed in an effort to produce functional prototypes in appropriate materials. One of the major challenges for rapid machining is to develop an automatic fixturing system for securing the part during the machining process. The method proposed in this paper is the use of sacrificial fixturing, similar to the support structures in existing rapid processes like Stereolithography. During the machining process, sacrificial supports emerge incrementally and, at the end of the process, are the only entities connecting the part to the stock material. This paper presents methodologies for the design of sacrificial …

Egypt's Information Society Strategy: A Critical Lexicography, Neil Mcbride, Bernd Carsten Stahl

Journal of International Technology and Information Management

The development of ICT policies within developing countries in the past ten years has opened up a new area for study. These documents chart the ambitions of the countries for the use of ICT to promote rapid development. As such they are intercultural documents, developing at the interface between the culture of the country and western economic culture. This paper develops a critical approach to understanding these documents and studying their message. The approach involves the preparation of a critical dictionary which identifies relevant terms within the ICT policy document and reflects on their multiple meanings. The approach was applied …

Usability Investigation Of E-Business Web-Based Forms, Gerald V. Post, Albert Kagan, Betsy Page Sigman

Journal of International Technology and Information Management

Usability on Web sites is critical because almost no training is provided for users on commercial sites. Instead, Web design relies on standards and consistency across sites. Traditional usability results indicated that computer forms should follow paper-based forms. Yet, Web paradigms have evolved that are quite different from paper-based forms. Specifically, this study reveals that users commit fewer errors and prefer simple forms limited to a single concept per screen. This conclusion significantly alters the recommendations for designing business forms.

Formal Verification Of Urban Traffic System Using The Concept Of Fuzzy Workflow Simulation, Manuj Darbari, Abhay Kumar Srivastava, Sanjay Medhavi

Journal of International Technology and Information Management

Modeling complex urban traffic system requires extensive use of workflow methodologies which can simulate almost real time traffic situations. Number of studies were done in the field of Urban Traffic Simulation like PLOTS, NETSIM and PALAMICS but none of them could provide a real formal solution. Our paper proposes a methodology using Fuzzy Petri nets for modeling real time traffic system. Fuzzy Petrinets are also visualised and tested by using Flow- Charter and HPSIM software packages. These packages help in providing successive iterations of process model for further refinement.

Supporting The Virtual Community: Social Bookmarking As A User- Based Classification Scheme In A Knowledge Library, Nicole Lytle, Tony Coulsom

Journal of International Technology and Information Management

Knowledge libraries hold the promise of widespread access to information available anywhere, anytime, freeing patrons from the geographical and temporal boundaries that currently exist. The classification of materials and subsequent searching of knowledge library content is an overall problem with many complex parts. Relevant classification is important for optimal information retrieval. This is especially important for the virtual communities that exist with extended organizations. Rooted in the virtual community and digital library literature, this paper develops a theory for improving the information classification and retrieval process of knowledge libraries that support virtual communities by applying social bookmarking techniques.