Operations Research, Systems Engineering and Industrial Engineering Commons^™

Research Of The Fuzzy Control System For Adjusting Thread Tension During The Warping Process, To'xtamurod Hayitmurodovich Avezov, Zokhid Ergashboyevich Iskandarov

Chemical Technology, Control and Management

The paper considered issues of research into a fuzzy control system for the warping process. During the warping process, the reasons that cause defects in the final finished product have been studied, firstly (remove this word) which are thread breakage, thread tangling, the formation of loops on or under the belt, hanging loose threads and similar factors. To study the warping process, its mathematical model is constructed. Kinematic parameters of stationary movement corresponding to the equilibrium mode were determined by solving the nonlinear functional matrix - equation of movement. The process of breakage the warp of the threads under oscillation …

Research Of A New Technological Flowsheet Parameters For Uranium Mining From Technogenic Uranium Ores, Nazarov Jamol, G.M. Allaberganova, H.L. Pulatov, A.M. Muzafarov

Chemical Technology, Control and Management

This paper presents the results of a study of the parameters of a new technological scheme for the extraction of uranium from technogenic uranium ores. The results of the analytical determination of the concentration of parent - ²³⁸U and daughter radionuclides - ²³⁴U , ²³⁰Th , ²²⁶Ra , ²²²Rn , ²¹⁸Pa , ²¹⁴Pb , etc. are presented . in the studied technogenic uranium ores. The principal scheme of the new uranium extraction technology from technogenic uranium ores is presented. The use of the classifier in a new scheme for separating granules of technogenic …

Assessment Of Metrological Errors Of Recognition Metrics In The Intelligent Control And Regulation System Of The Cotton Harvesting Machine, Erkin Uljaev, Utkirjon Murodillaevich Ubaydullaev, Azizjon Abdulla Ugli Abdulhamidov

Chemical Technology, Control and Management

This article presents a method for assessing the error of metrics of an intelligent system for monitoring and regulating the width of the working gap of the harvesting apparatus of a cotton picker. To assess the error, the calculation of the average value of the standard deviation of metrics, absolute systematic and random errors, as well as absolute and relative total errors are used. The results of these calculations will allow us to determine the accuracy of the recognition system and opportunities for its improvement.

Synthesis Of An Adaptive Neuro-Fuzzy Control System For Steam Generator Temperature, Isomiddin Xakimovich Siddikov, Dilnoza Maxamadjanovna Umurzakova

Chemical Technology, Control and Management

This paper is devoted to the modeling and synthesis of an adaptive neuro-fuzzy control system for steam generator temperature. Temperature control systems play an important role in industry because accurate and stable control is a prerequisite for the efficient operation of steam systems. Traditional control methods based on mathematical models and fixed parameter controllers may have limitations in providing optimal performance and adapting to changing operating conditions. The paper proposes a synthesized system combining fuzzy logic and adaptation methods to achieve more accurate and stable temperature control. A detailed structural diagram of the system, modeling, and tuning methods are presented. …

Decision-Making Algorithms For Drilling Instrument Control Systems, Fuzayl Fozil Ugli Odilov

Chemical Technology, Control and Management

The control of the movement of the drilling tool and the structure of the well are considered. An effective control algorithm for drilling systems that provides control of well trajectory parameters is analyzed. In technological processes, it is necessary to control several parameters or several systems at the same time. It is considered necessary to create decision-making algorithms for the formation of managerial effects for the control system of such technological processes. The controlled oriented type of the bottom of the drill string was analyzed. Work was carried out on the decision-making algorithm for the processing of control effects. The …

Algorithms And Models For Synthesis Of Elements Of Digital Information Systems, Odil Abdujalilovich Jumaev, M.T. Ismoilov, V.B. Pulatov, G.X. Rashidov

Chemical Technology, Control and Management

The development of algorithms for noise-tolerant and high-speed measurement systems involves an integrated approach that encompasses methods of data processing and transmission, as well as mechanisms for rapid response to changes. This paper presents the key principles and techniques used in such technologies. The information systems are thoroughly analyzed, including the use of signal processing techniques and their identification, filtering using various statistical techniques to determine signal parameters and the development of algorithms to analyze and classify signals. Critical aspects of the system such as performance, reliability, security and scalability are also evaluated. The paper discusses information system structures and …

Modernization Of Water Flow Measurement In Open Irrigation Systems Using The Slope-Area Method, R.M. Aliev, Djalilov Anvar

Chemical Technology, Control and Management

This article describes two methods for determining water flow in open irrigation systems: “speed - area” and “slope - area”. The authors considered the problem of its modernization using the existing method for determining water flow “slope - area” in open irrigation systems. The essence of the issue is the remote transfer of parameters necessary for calculating water flow in open irrigation systems and improving the means of their processing. In scientific studies conducted by the authors, the required hydraulic parameters were studied using the “slope - area” and “speed - area” water flow methods. Based on experimentally obtained data, …

Dynamic Characteristics Of Magnetoelectric Linear Actuators Of Control Systems, Мakhmudjon Muxamedovich Аbdullayev, Rasul Ernazar Ogli Abdiev

Chemical Technology, Control and Management

This paper presents the results of studies carried out on magnetoelectric drives that carry out linear movement, models of drives are built and, on their basis, studies of the main indicators associated with the movement of a linear armature are carried out, such as: speed of movement, acceleration, current values, voltage and traction force of the armature. Also presented are the results of a study of magnetoelectric linear motion drives based on an analysis of graphs of their dynamic characteristics.

Improving Technology For Producing Complex Fertilizer From Low-Grade Phosphorites Of The Central Kyzylkum, A.Zh. Allamuratova, A.U. Erkaev, A.M. Reimov, Saparbay Kazakhbaev, Dilshodbek Kurbiyazov

Chemical Technology, Control and Management

The methods of nitric acid processing of phosphate raw materials are analyzed. A technology has been developed for the nitric acid processing of phosphate raw materials into nitrogen-phosphorus fertilizer with the implementation of the process in a condensed pulp by adding sulfuric acid. A technology for producing complex fertilizers with a wide range of N:P₂O₅:K₂O ratios with improved physico-chemical parameters due to the introduction of various potassium salts into the process is proposed.

Synthesis Of Local Control Systems For Underwater Units Cleaning Bottom Sediments In Reservoirs, Yuriy Gennadiyevich Shipulin, Zebiniso Akmalovna Zayniddinova

Chemical Technology, Control and Management

The article discusses the issues of synthesizing local control systems for underwater units for cleaning bottom sediments in reservoirs. It is shown that the protection and rational use of natural reservoirs and the fight against their premature siltation is becoming an urgent task.

It is proposed to use small-sized underwater units, consisting of information and measuring devices, to carry out search work for cleaning bottom sediments under water; control systems; actuators and means of communication with humans.

It is shown that the task of controlling the loading of an underwater unit (UU) requires maintaining optimal performance while simultaneously taking into …

Algorithms For Structural Synthesis Of Control Systems For Dynamic Objects Under Conditions Of Unmeasurable Disturbances, Husan Zakirovich Igamberdiev, Uktam Farkhodovich Mamirov, Bunyod Mamurjon Ugli Buronov

Chemical Technology, Control and Management

The paper talks about ways to use inverse dynamic models to structure a control system for moving objects when disturbances are not measured. To solve the main problems that arise when implementing the inverse dynamic model method, methods for synthesizing inverse systems with given dynamic characteristics are used. The solution to this problem is obtained based on the theory that dynamic observers are invariant to unmeasured input influences. We broke down the matrix operator on the right into elementary orthogonal rotation matrices and on the left into permutation matrices to get a stable answer to the equation of the current …

Artificial Neural Network Based Grain Moisture Measuring Device, Erkin Eljaev, Shohrux Nurali O‘G‘Li Narzullayev, Elyor Faxriddinovich Khudoyberdiev

Chemical Technology, Control and Management

To date, the intellectualization of solving technical issues in managing, controlling, and measuring technological processes in all branches of industrial production is considered an urgent task. In this regard, a class of intelligent devices and sensors has emerged. Intelligent devices and sensors differ from their analog counterparts in that they have functions such as automatic adjustment of the measurement range, self-calibration, data processing, and decision-making. The article discusses the development of intelligent measuring instruments based on a capacitive transducer for measuring the moisture content of grain and grain products.

Synthesis Algorithm Of Control System Based On Neural Network For The Gas And Oil Process, Jasur Sevinov, Abdishukurov Maqsudovich Shavkat, A.Z. Shodiyorov

Chemical Technology, Control and Management

Automatic control systems in the oil and gas processing are considered. After extraction of natural gas condensate, management of technological parameters plays an important role in its processing. Among the parameter of regulating algorithms, control based on neural network technology was considered. These control systems are created on the basis of algorithms of neural network technology. There are several structures of neural networks according to their structure. Differences in the process of information processing of these branching structures are considered.

Sediment Characteristics And Hydrocarbon Composition Of Makukwa Seep In Southern Tanzania: Potential Implications For Subterranean Hydrocarbon Accumulation, Makungu M. Madirisha

Tanzania Journal of Engineering and Technology (TJET)

Exploring the interplay between natural seeps and nearby sediment and hydrocarbon properties is key to unlocking subsurface hydrocarbon potential. This study presents findings on the hydrocarbon composition and sediment characteristics of the Makukwa seep in southern Tanzania, providing insight into subterranean hydrocarbon accumulation. Sediment analysis across areas A and B, located approximately 20 m apart, showed a decrease in porosity with depth, indicative of typical sandstone formations. Area A, near the seeps, exhibited porosity ranging from 23% to 36%, whereas Area B, further away, showed porosity ranging from 22% to 38%. This suggests that a lower cretaceous sandstone layer may …

Design And Optimization Of An Azeotropic Distillation Pilot Plant For The Production Of Pure Ethanol, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

This study aimed to design an azeotropic distillation plant using Aspen Plus® V10 software and determine optimal process conditions for producing pure ethanol greater than 95% from pre-concentrated near-azeotropic ethanol-water solution. The non-random two-liquid Redlich-Kwong thermodynamic model was the base method for property analysis and performance prediction. Modelling and simulation of the converged process were conducted for fixed column variables (R = 5, N = 12 and p = 1 atm). Plant operating parameters were varied in the range of 0 to 1 for the pre-heater vapour fraction, 2 to 10 for the column feed plates (NFP), 2 to 6 …

Effect Of Zr And W Doping On Microstructures, Transition Temperature And Solar Transmittance Modulation Of Thermochromic W/Zr Co-Doped Vo2 Thin Films, Haji F. Haji

Tanzania Journal of Engineering and Technology (TJET)

Thermochromic W/Zr co-doped VO2-based thin films with different concentrations of Zr were successfully deposited on soda lime glass substrates by direct current (DC) magnetron sputtering of V(99)W(01) alloy and Zr targets at a substrate temperature of 425 °C. The films were characterized by x–ray diffraction (XRD), atomic force microscopy (AFM), Rutherford backscattering spectroscopy (RBS), two-point probe and UV/VIS/NIR spectroscopy. The film’s structural properties evolution was significantly influenced by Zr concentration in the films. The transition temperature and hysteresis loop widths of the films were found to decrease with increasing Zr concentration. For the Zr concentrations of 0.21 at.%, 0.23 at.% …

Study Of The Effects Of Thermal Aging Coupled With Shot-Peening Treatment Of Carbonitrided Din 1.6587 Low Alloy Steel On Retained Austenite And Residual Stresses, Richard J. Katemi

Tanzania Journal of Engineering and Technology (TJET)

This work investigated the effects of thermal aging and shot-peening of carbonitrided 1.6587 steel grade on retained austenite and residual stresses. After carbonitriding samples contained maximum of 0.87% carbon, 0.34% nitrogen and 50 mass. -% retained austenite. Thermal aging conditions investigated were -30°C, 90°C and 150°C while the aging period were 14, 96 and 720 hours. After thermal aging, some of the samples were subjected to shot-peening treatment using standard cut wire shots StD – G3 - 0.6 mm VDFI 8001 with intensity in the range of 0.25 to 0.30 mmA and coverage of 1.00 to 1.24 x 98%. It …

Identification Of Faults In Highways Using Approximation Methods And Algorithms, Khudayberdiyev Khakkulmirzayevich Mirzaakbar, Anvar Asatilloyevich Ravshanov

Chemical Technology, Control and Management

Many fast Fourier transforms are used to identify defective parts of uneven surfaces on roads and send information to relevant organizations on the road, using the " RAVON YO‘LLAR" application installed on a mobile device during car movement. We determine the uneven parts of the road. Smooth and well-maintained roads reduce the risk of vehicle collisions, skidding and other road-related incidents. Timely measures contribute to overall safety, comfort and economic efficiency.

Synthesize A Neural Network Parameter Optimizer For An Adaptive Pid Controller, Nashvandova Gulruxsor Murot Qizi

Chemical Technology, Control and Management

Wide application of proportional-integral-differential (PID)-regulator in industry requires constant improvement of methods of its parameters superstructuring. In the paper, the questions of optimization of PID-regulator parameters with application of methods of neural network technology are considered. A methodology for selecting the architecture of neural network optimizer designed to determine the tuned parameters of PID regulator is proposed. The algorithm of training of the neural network, with the set on the basis of the method of inverse gradient propagation is offered. The proposed improved PID-neural regulator allowed to provide stabilization of neural network operation and its trainability in the control loop …

Analytical-Critical Review Of Widely Used Industrial Devices For Drying Mineral Fertilizers, Djalolitdin Paxritdinovich Mukhitdinov, Aleksey Viktorovich Schulz

Chemical Technology, Control and Management

The article is devoted to the review of the modern state of research in the mineral fertilizers drying field, critical analysis and comparison of widely used drying apparatuses. There are procedures of preliminary equipment selection for soluble fertilizers industrial drying on the basis of such criteria as productivity, efficiency, energy saving, environmental impact degree, indicating the possible advantages and disadvantages of different application variants.

Calculation Of Hydraulic Resistance Of A Tubular-Gridse Nozzle With Spiral Turbulizers, Nurmukhamedov Habibulla Sagdullaevich, Mavlonov Elbek Tulkinovich, S.Kh. Nishonova, Kh.S. Nurmukhamedov

Chemical Technology, Control and Management

The article presents the results of an experimental study on the hydraulic resistance of a tubular-grid nozzle made of smooth pipes and pipes with spiral turbulators. Experiments were carried out with nozzles made of smooth pipes and pipes with turbulators. Spiral turbulators are placed discretely with a step t/d=0,3125-0,9375 and installed on a tube sheet in a checkerboard pattern with a step s/d=1,15-10. Experimental studies were carried out with air flow in the transition region.

It has been established that with increasing numerical values of the dimensionless parameter s/d, the resistance of the pipe package decreases from 1,3 to 1,8 …

Development Of A Criterion Assessing The Level Of Relationship Of Multiple Identified Characteristics For Classification, Mirzoyan Mirzaaxmedovich Kamilov, Oybek Zokirovich Koraboshev, Bobomurod Mamitjonovich Tojiboev

Chemical Technology, Control and Management

This article discusses an optimized version of the standard design developed by Yu.I.Zhuravlev, an optimization procedure through an algebraic approach based on precedent algorithms that solves the problem of pattern identification. The formation of the convex hull of the recognition operator and corrective procedures of information models by mutual compensation of each other was also studied. In addition, the functional connection of recognition operators and the definition of idempotent connection of operators are analyzed.

Chromatographic Analysis Of The Chemical Composition Of Pyrolysis Distillate, Sh.T. Juraev, B.F. Muxiddinov, U.T. Tailakov

Chemical Technology, Control and Management

The paper presents the results of a study of the physico-chemical characteristics of the liquid fraction of products of thermal oxidative pyrolysis of worn tires. The mass fraction of the volatile gas compounds, the optimal boiling points of the obtained condensates and the flashpoint of pyrolysis liquids, together with the mass composition of cracking products of rubber products at high-temperature pyrolysis at a temperature of 800-900 °C, were determined. Chromatographic analysis allowed us to determine the composition, mainly the mass composition of pyrolysis products, which consisted of carbon (42.8%), higher aliphatic and aromatic hydrocarbons (17.0%), methane (10.2%), benzene (4.2%) and …

Strategy For Predictive Control Of The Rectification Process Based On A Model Controller With A Given Forecast, Ildar Rafkatovich Sultanov

Chemical Technology, Control and Management

A method is being developed to optimize the generated controls for the multicomponent distillation process with prediction, based on predictive data with a moving horizon. The difference between this method and the classical modeling approach, in which the percentage of the degree of opening of valves installed on the output streams of the column is used as control actions, is that control occurs on the feedback principle. The proposed method is based on the use of a dynamic process model to optimize control actions in real time in order to achieve certain production targets. The essence of the MPC approach …

A Neural Network Model For Monitoring And Forecasting The Process Of Storing Oilseeds, N.A. Kabulov

Chemical Technology, Control and Management

The paper presents the results of research on the control, forecasting and management of the storage process of oilseeds. Vegetable oil production and energy consumption are two important factors of oilseed storage systems. The first ones should meet the needs of the population quantitatively and qualitatively. As a result, in order to properly control these two important aspects, it is necessary to maintain an appropriate microclimatic environment using a computational decision support system (DSS) that is able to adapt to changes in environmental characteristics. The multilayer perceptron neural network (MLP-NN) was developed to simulate the temperature and relative humidity profiles …

Evaluation Of Environmental Management System For Small And Medium Enterprises In Dar Es Salaam, Tanzania, Juma M. Matindana

Tanzania Journal of Engineering and Technology (TJET)

A system that manages environmental issues of Small and Medium Enterprises (SMEs) from the time of acquisition of raw materials up to disposal of the product is not well clear, especially in Tanzania. Most of the studies have been conducted in the field of environment management but few of them address the evaluation of the management of SMEs activities with respect to the environment. Although the nature of activities of SMEs has little noticeable environmental implications at the individual level but the impact is large due to diversification and labour intensity of these SMEs. SMEs employ about 20% of the …

A Two-Stage Based Life Cycle And Principal Component Analysis For Decision Support Of Potential Municipal Solid Wastes Management Scenarios, Case Study Dar Es Salaam, Tanzania, Edwin Richard Ndibalema Dr

Tanzania Journal of Engineering and Technology (TJET)

In most of the urban areas of Tanzania, poor and inadequate solid waste management is a growing environmental and public health concern. Despite an array of solid waste management options, choosing an appropriate one remains a challenge. This study applied a novel two-stage-based approach to assess the environmental impacts and sustainability performance of the 27 scenarios for municipal solid wastes (MSW) management of Dar es Salaam City, Tanzania. In the first stage, the study utilized a life cycle analysis (LCA) to quantify the environmental impacts of MSW scenarios. In the second stage, the study used the principal component analysis (PCA) …

Augmented Finite Control Set Mpc Design Technique For Wide Speed Range Control Of Permanent Magnet Synchronous Motor Drives, Francis Mwasilu

Tanzania Journal of Engineering and Technology (TJET)

The effective motion control task is highly influencing the final drive performance in wide-range motor drives applications such as electric vehicles (EVs), washing machines, compressors, elevators and lathe machines. Recently, permanent magnet synchronous motor (PMSM) drive has been widely employed in these applications to achieve desired performances such as high efficiency, high torque requirements with minimum size “occupancy”. The PMSM drive features combining with these modern drive applications are highly nonlinear and the desired operation requirements demand high-performance control schemes with fast system response and robustness features. Linear control schemes are usually implemented to drive the PMSM that entail trade …

Cost Estimation Proxy Models For Economic Evaluations In Petroleum Projects: A Case Study From The Onshore Gas Field In The Southern Coastal Tanzania Basin, Fulmence Kaborogo

Tanzania Journal of Engineering and Technology (TJET)

Petroleum economic evaluation involves estimating revenues from forecasted production profiles and field costs including capital expenditures (CAPEX), drilling expenses (DRILLEX), and operating expenses (OPEX). The existing cost-estimating tool requires several inputs making it time-intensive and difficult to use with few data during the early stages of projects. Majority of the previously developed time saving cost estimations proxy models rely on unrealistic assumptions that include uniform operational costs for different fields with a different number of wells, casings, and drilled depths. This work focused at developing proxy models that consider the variability of the development costs with different parameters. The developed …

Development Of Dynamic Mass-Energy-Thermodynamics Constrained Hybrid Neural Network Models For Process Systems Applications, Angan Mukherjee

Graduate Theses, Dissertations, and Problem Reports (ETD)

First-principles models can provide very good predictions even for cases when there are no data at all, or data are limited in certain range of operating conditions, or for cases where data collection is infeasible. However, the development of accurate first-principles models for complex nonlinear dynamic systems can be time consuming, computationally expensive, and may be infeasible for certain systems due to lack of sufficient knowledge (information). It is also challenging to adapt first-principles models for time-varying systems. Furthermore, it can be difficult, if not impossible, to develop accurate models for some complex phenomena that are poorly understood. On the …