Operations Research, Systems Engineering and Industrial Engineering Commons^™

Evaluating Electrification Of Fossil Fuel-Fired Boilers For Decarbonization Using Discrete Event Simulation, Nahian Ismail Chowdhury

Graduate Theses, Dissertations, and Problem Reports (ETD)

Decarbonizing fossil fuel usage is crucial in mitigating the impacts of climate change. CO2, which comprises the major portion of greenhouse gas, is emitted from burning fossil fuels. One of the significant sources of fossil fuel user is industrial process heating, and most of the heating in industrial processes is achieved through boilers. Electrification is a promising solution for decarbonizing these boilers, as it enables renewable energy sources to generate electricity, which can then be used to power the electric boilers. The electrification of boilers can reduce greenhouse gas emissions, improve air quality, and increase energy efficiency. However, it requires …

Coaxial Beam Eaxle Modeling And Analysis For Gawr Limits, Alexander Cebriak, Jackson Foster, Chris James

Williams Honors College, Honors Research Projects

The goal of this project was to design three different models of a coaxial beam eAxle for a range of electric vehicles. The requirement was to satisfy three different loading conditions, each characterized by a GAWR. These three loading conditions were 3000lb, 7500lb, and 10,000lb. This was done by first creating a model based on a basic outline given by Schaeffler. This model was then analyzed using Ansys®, and then iterated upon by designing new models using the 3D design program Solidworks. The iteration process was continued using more Ansys® analysis, as well as calculations to determine things like bolt …

Hendrickson Lift Kit, Matthew Rozmajzl

Williams Honors College, Honors Research Projects

This research project will be completed with Hendrickson Trailer as the sponsor. The goal of the project is to create a lift kit for a newer suspension system. The lift kit must provide enough lift force to lift an axle off the road and suspend it off the road while in transit. There are similar systems offered for different products at Hendrickson, but the configuration of this system is such that new brackets must be designed. The benefit of such a system is a reduction in wear on the lifted tires, and thus an increase in the life of the …

Part Design Geometry-Driven Toolpath Optimization For Additive Manufacturing Energy Sustainability Improvement, David Kolawole Somade

Graduate Research Theses & Dissertations

One of the most promising new manufacturing technologies in the past three decades isadditive manufacturing (AM), also commonly known as three-dimensional (3D) printing or rapid prototyping. The energy consumption problem in AM can be significant when it is adopted at the industrial scale or used under resource-restricted conditions. The energy consumption of an AM process is influenced by several factors including bed heating, filament extrusion, material infill, component cooling, etc. All these factors are further determined by the equipment and the toolpath for a specific printing task. Build orientation and tool-path direction are frequently used to optimize part and process …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

College of Graduate Studies: Theses & Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

Simulating The Impact Of Emissions Control On Economic Productivity Using Particle Systems And Puff Dispersion Model, Najam Khan

Electronic Theses and Dissertations

A simulation platform is developed for quantifying the change in productivity of an economy under passive and active emission control mechanisms. The program uses object-oriented programming to code a collection of objects resembling typical stakeholders in an economy. These objects include firms, markets, transportation hubs, and boids which are distributed over a 2D surface. Firms are connected using a modified Prim’s Minimum spanning tree algorithm, followed by implementation of an all-pair shortest path Floyd Warshall algorithm for navigation purposes. Firms use a non-linear production function for transformation of land, labor, and capital inputs to finished product. A GA-Vehicle Routing Problem …

Pressure Induced By Roll-Down Foam-Earplugs On Earcanal, Ahmed Dalaq, Luiz Melo, Franck Sgard, Olivier Doutres, Éric Wagnac

Études primaires

Physical discomfort of earplug is a common complaint, so much so it jeopardizes the health and safety of workers, resulting in frequent noncompliance to proper wearing of earplugs. A pressing need thus arises to understand the underlying mechanics for the interaction of earplugs with earcanal walls. An idealized cylindrical geometry of earcanal is first treated with computational and analytical modeling to predict the pressure induced by roll-down cylindrical PVC foam earplugs. In order to predict representative pressure values and distribution, we estimated the hyperelastic properties of foam-based earplugs and characterized their behavior using a stent testing machine (J-Crimp^TM machine) …

Risk Management Of Carbon Steel Piping In Sweet Environment Multiphase Fluid Production, Triadhi Panthun Tiggor, Rini Riastuti

Journal of Materials Exploration and Findings

As well reserved depleted and limited, it is necessary to lower the capital expenditure so that lifting SZ reservoir be more profitable. This article first contextualizes the effort done to increase the hydrocarbon lifting in a mature field. Despite the importance to sustain the production, and massive studies done to quantify the associate risk, no structured methodology proposed to manage the risk in respect to optimize the production expenditure by selection of carbon steel as alternative for corrosion resistance material piping. Hence, this article proposed a framework to support the decision-making process to operate in safely manner. Real case study …

Dynamic Rbi With Central Difference Method Approach In Calculation Of Uniform Corrosion Rate: A Casestudy On Gas Pipelines, M.Riefqi Dwi Alviansyah, Fernanda Hartoyo, Zahra Nadia Nurullia, Ari Kurniawan

Journal of Materials Exploration and Findings

The oil and gas industry generally uses a piping system to drain fluids. Even though the pipes used have been well designed, the use of pipes as a means of fluid transportation still provides the possibility of failure that can occur at any time, one of which is due to uniform corrosion. The use of standard Risk Based Inspection (RBI) according to the API RBI 581 document has been widely used to anticipate potential failures to pipe components. The use of standard RBI can reduce the risk of failure significantly. Because the standard RBI considers the component risk value to …

The Rise Of Terrorism In Africa And What It Means For U.S. Policymakers, Bridget Mary Hughes

Master's Theses

This thesis utilizes three case studies to measure the rise of terrorism in Africa. This qualitative data leads the reader to one ultimate question: what does the rise in terrorism in Africa mean for the United States (U.S.) and U.S. policymakers, National Security academia, students in National Security, if anything at all? The answer is: if civilian and military compounds are being targeted by these violent extremists, as these three case studies demonstrate, it is my recommendation that U.S. policymakers cease sending troops to the African theater and, instead, allocate funding to the citizens and nonprofits of the countries whom …

Callaway Measurement Device, Andre S. Fisher, Roman Hays, Blake Sousa, Grant Gabrielson

Mechanical Engineering

The purpose of this document is to illustrate the Callaway Measurement Device senior project from start to finish. The challenge given to the team was to update and improve a gauge used by Callaway employees to measure the loft, lie, and face angle of their full spectrum of golf clubs. Once the team understood how the pre-existing gauge operates, the team conducted background research into other technologies that could improve the gauge. The team decided to digitalize the device amongst other tweaks to reduce error. Because the CAD files were not available for the pre-existing device, the team began reverse …

Novel Hitch Cargo Cart, Cesilio Sanchez Ramirez, Lance Haidet, Richard Lontoc, Tyler Selinka

Mechanical Engineering

This document presents the engineering design process used to develop, manufacture, and test a new and improved iteration of a hitch cart prototype. This process was performed by a team of four mechanical engineering seniors as part of California Polytechnic State University, San Luis Obispo’s senior design pathway. The goal of this project was to develop a sturdy and reliable iteration of our sponsor’s hitch cart prototype, that integrated the functionality of a vehicle hitch cargo platform and that of a height adjustable cargo cart into a single streamlined and easy to use product. This design could be used by …

Multiple Heat Exchanger Cooling System For Automotive Applications – Design, Mathematical Modeling, And Experimental Observations, Zaker Syed

All Dissertations

The design of the automotive cooling systems has slowly evolved from engine-driven mechanical to computer-controlled electro-mechanical components. With the addition of computer-controlled variable speed actuators, cooling system architectures have been updated to maximize performance and efficiency. By switching from one large radiator to multiple smaller radiators with individual flow control valves, the heat rejection requirements may be precisely adjusted. The combination of computer regulated thermal management system should reduce power consumption while satisfying temperature control objectives. This research focuses on developing and analyzing a multi-radiator system architecture for implementation in ground transportation applications. The premise is to use a single …

Evaluation And Implementation Of Lean Engineering Principles For Improving A University Rocket Team, Alan Garcia

Open Access Theses & Dissertations

In the present day, lean is a tool applied to manufacturing industries trying to reduce wasteand non-value-added work to every process during the supply chain. While implementing lean thinking in the industry has been highly effective, it is less common for academic purposes. However, it can also improve performance if the concept is correctly applied. The purpose of this thesis is to show and analyze the application of Lean Engineering thinking and its six principles to the Sun City Summit Rocket Team from the University of Texas at El Paso which competed in the Intercollegiate Rocket Engineering Competition (IREC) Spaceport …

Performance Comparison Of Several Control Algorithms For Tracking Control Of Pantograph Mechanism, Laylaa Mahmoud Eng, Mohamed Shamseldin Dr, Mohamed Sallam Dr, Abdelghany Mohamed Prof

Future Engineering Journal

A sort of parallel manipulator known as a pantograph robot mechanism was created primarily for industrial requests that required high precision and satisfied speed. While tracking a chosen trajectory profile requires a powerful controller. Because it has four active robot links and one robot passive link in place of just two links like the open chain does, it can carry more loads than the open chain robot mechanism while maintaining accuracy and stability. The calculated model for a closed chain pantograph robot mechanism presented in this paper takes into account the boundary conditions. For the purpose of simulating the dynamics …

Relative Rate Observer Self-Tuning Of Fuzzy Pid Virtual Inertia Control For An Islanded Microgrid, Ahmed H. Mohamed, Helmy M. El Zoghby, Mohiy Bahgat, A. M. Abdel Ghany

Future Engineering Journal

Expanding the usage of renewable energy in islanded microgrids leads to a reduction in its total inertia. Low inertia microgrids have difficulties in voltage and frequency control. That affected saving its stability and preventing a blackout. To improve low inertia islanded microgrids' dynamic response and save their stability, this paper presented relative rate observer self-tuning fuzzy PID (RROSTF-PID) based on virtual inertia control (VIC) for an islanded microgrid with a high renewable energy sources (RESs) contribution. RROSTF-PID based on VIC's success in showing remarkable improvement in the microgrid's dynamic response and enhancement of its stability. Moreover, it handles different contingency …

Using Strategic Options Development And Analysis (Soda) To Understand The Simulation Accessibility Problem, Andrew J. Collins, Ying Thaviphoke, Antuela A. Tako

Engineering Management & Systems Engineering Faculty Publications

Simulation modelling is applied to a wide range of problems, including defense and healthcare. However, there is a concern within the simulation community that there is a limited use and implementation of simulation studies in practice. This suggests that despite its benefits, simulation may not be reaching its potential in making a real-world impact. The main reason for this could be that simulation tools are not widely accessible in industry. In this paper, we investigate the issues that affect simulation modelling accessibility through a workshop with simulation practitioners. We use Strategic Options Development and Analysis (SODA), a problem-structuring approach that …

A Survey Of Smart Manufacturing For High-Mix Low-Volume Production In Defense And Aerospace Industries, Tanjida Tahmina, Mauro Garcia, Zhaohui Geng, Bopaya Bidanda

Manufacturing & Industrial Engineering Faculty Publications

Defense and aerospace industries usually possess unique high-mix low-volume production characteristics. This uniqueness generally calls for prohibitive production costs and long production lead-time. One of the major trends in advanced, smart manufacturing is to be more responsive and better readiness while ensuring the same or higher production quality and lower cost. This study reviews the state-of-the-art manufacturing technologies to solve these issues and previews two levels of flexibility, i.e., system and process, that could potentially reduce the costs while increasing the production volume in such a scenario. The main contribution of the work includes an assessment of the current solutions …

Impulse, Fall 2022, University Marketing And Communications, Jerome J. Lohr College Of Engineering

Impulse (Jerome J. Lohr College of Engineering Publication)

2 | Sanjeev Kumar Takes Helm as College’s 12th Dean
5 | College Develops Partnerships in India, Turkey
6 | Faculty News
8 | Aerofly — Profs, Alum Partner To Build Unique Drone
10 | Researchers Find Way to Extend Produce Shelf Life
12 | SDSU Claims National Title in Quarter-Scale Tractors
14 | Nation’s Top ASCE Chapter Housed at SDSU
16 | National Geo-Video Title Won By State Students
18 | Summer Brings Engineering Camps to Campus
20 | Haleigh Timmer — Money on the Court, In Classroom
22 | Daniel Burkhalter — Day in the Life of Student-Athlete …

A Numerical Study On The Powder Flowability, Spreadability, Packing Fraction In Powder Bed Additive Manufacturing, Yeasir Mohammad Akib, Ehsan Marzbanrad, Farid Ahmed, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

The powder bed fusion (PBF) process is widely adopted in many manufacturing industries because of its capability to 3D print complex parts with micro-scale precision. In PBF process, a thermal energy source is used to selectively fuse powder particles layer by layer to build a part. The build quality in the PBF process primarily depends on the thermal energy deposition and properties of the powder bed. Powder flowability, powder spreading, and packing fraction are key factors that determine the properties of a powder bed. Therefore, the study of these process parameters is essential to better understand the PBF process. In …

Synthesizing And Printing Of Tin Oxide Nanoparticles Using A Single Ultrafast Laser System: A Feasibility Study, Enrique Contreras Lopez, Farid Ahmed, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

In laser-based manufacturing, processing setup customization is one of the popular approaches used to enhance diversity in material processing using a single laser. In this study, we propose setup design modification of an ultrafast laser system to demonstrate both Tin Oxide (SnO2) nanoparticle synthesis from bulk metal, and post printing of said nanoparticles using Laser Induced Forward Transfer (LIFT) method. Using the Pulse Laser Ablation in Liquid (PLA-L) method, nanoparticles were synthesized from a bulk tin metal cube submerged in distilled water. Such nanoparticles dispersed in water can form colloidal ink that can be used for different printed electronics applications. …

Ultrafast Laser Direct Writing Of Conductive Patterns On Polyimide Substrate, Ishrat Jahan Biswas, Enrique Contreras Lopez, Farid Ahmed, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

Laser direct writing (LDW) is a fast and cost-effective method for printing conductive patterns in flexible polymer substrates. The electrical, chemical, and mechanical properties of polyimide (PI) make it an attractive material choice for laser writing of conductive circuits in such polymer. Electrically insulating PI has shown great potential for flexible printed electronics as LDW enables selective carbonization in the bulk of such material leading to the formation of conductive lines. However, existing studies in this area reveal a few key limitations of this approach including limited conductivity of written structures and fragility of carbonized PI. Therefore, more research is …

Automated Posture Positioning For High Precision 3d Scanning Of A Freeform Design Using Bayesian Optimization, Zhaohui Geng, Bopaya Bidanda

Manufacturing & Industrial Engineering Faculty Publications

Three-dimensional scanning is widely used for the dimension measurements of physical objects with freeform designs. The output point cloud is flexible enough to provide a detailed geometric description for these objects. However, geometric accuracy and precision are still debatable for this scanning process. Uncertainties are ubiquitous in geometric measurement due to many physical factors. One potential factor is the object’s posture in the scanning region. The posture of target positioning on the scanning platform could influence the normal of the scanning points, which could further affect the measurement variances. This paper first investigates the geometric and spatial factors that could …

Minimax Registration For Point Cloud Alignment, Zhaohui Geng, Mauro Garcia, Bopaya Bidanda

Manufacturing & Industrial Engineering Faculty Publications

The alignment, or rigid registration, of three-dimensional (3D) point clouds plays an important role in many applications, such as robotics and computer vision. Recently, with the improvement in high precision and automated 3D scanners, the registration algorithm has become critical in a manufacturing setting for tolerance analysis, quality inspection, or reverse engineering purposes. Most of the currently developed registration algorithms focus on aligning the point clouds by minimizing the average squared deviations. However, in manufacturing practices, especially those involving the assembly of multiple parts, an envelope principle is widely used, which is based on minimax criteria. Our present work …

Turning Of Carbon Fiber Reinforced Polymer (Cfrp) Composites: Process Modeling And Optimization Using Taguchi Analysis And Multi-Objective Genetic Algorithm, S. M. Abdur Rob, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications

Carbon Fiber Reinforced Polymer (CFRP) composites have been widely used in aerospace, automotive, nuclear, and biomedical industries due to their high strength-to-weight ratio, corrosion resistance, durability, and excellent thermo-mechanical properties in non-oxidative atmospheres. Machining of CFRP composites has always been a challenge for manufacturers. In this research, a comparative study was performed between the optimal machining parameters of coated and uncoated carbide inserts obtained from the Multi-Objective Genetic Algorithm during turning of CFRP composites. It was found that coated carbide inserts provide lower tool wear and surface roughness, but higher cutting forces compared to those of uncoated carbide inserts …

Ultrafast Laser Ablation Of Inconel 718 For Surface Improvement, Sampson Canacoo, Enrique Contreras Lopez, Oscar Coronel, Farid Ahmed, Jianzhi Li, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications

Inconel 718 is considered difficult to machine because of its ability to maintain its properties at high temperatures. The low thermal conductivity of the alloy causes accelerated tool deterioration when machining. Selective laser melting (SLM) additive manufacturing introduces a possibility of eliminating these difficulties, and producing complex shapes with this difficult-to-machine material. However, high surface roughness and porosity usually occur at the surface of components produced through additive manufacturing. In this study, the surfaces of Inconel 718 samples produced through selective laser melting were treated using laser ablation. The process parameters for the laser ablation process were analyzed in …

Preface Of Volume 1 Issue 1 On Journal Of Materials Exploration And Findings (Jmef), Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

The Optimization Of Failure Risk Estimation On The Uniform Corrosion Rate With A Non-Linear Function, Fernanda Hartoyo, Jaka Fajar Fatriansyah, Imam Abdillah Mas'ud, Farhan Rama Digita, Hanna Ovelia, D. Rizal Asral

Journal of Materials Exploration and Findings

Failures in the oil and gas pipeline system are conditions that must be avoided and anticipated because the losses due to the failures can occur at a very high level. Internal corrosion is one of the significant causes of the failures in pipeline systems. In addition, this type of corrosion is due to the high content of carbon dioxide and other corrosive substances in crude oil and natural gas. Therefore, an optimal inspection scheduling system is required to prevent the possibility of pipeline failures due to corrosion and to avoid any overspending on the budget due to excessive inspection scheduling. …

Contents, Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

Smart Manufacturing—Theories, Methods, And Applications, Zhuming Bi, Lida Xu, Puren Ouyang

Information Technology & Decision Sciences Faculty Publications

(First paragraph) Smart manufacturing (SM) distinguishes itself from other system paradigms by introducing ‘smartness’ as a measure to a manufacturing system; however, researchers in different domains have different expectations of system smartness from their own perspectives. In this Special Issue (SI), SM refers to a system paradigm where digital technologies are deployed to enhance system smartness by (1) empowering physical resources in production, (2) utilizing virtual and dynamic assets over the internet to expand system capabilities, (3) supporting data-driven decision making at all domains and levels of businesses, or (4) reconfiguring systems to adapt changes and uncertainties in dynamic environments. …