Operations Research, Systems Engineering and Industrial Engineering Commons^™

Golf Club Prototyping And Design For Spin Rate Tuning, Cole Nygren, Jordan Wright, Jesse Yap

Industrial and Manufacturing Engineering

The aim of this project was to design a golf wedge capable of increasing backspin for the amateur golfer. This was accomplished by embedding a metal lattice structure behind the clubface to allow the face to elastically deform slightly upon impact. This would increase contact time between the club and ball. The mechanism of spin generation was discussed and the relationship between contact time and spin rate was established. The design was enabled by using additive manufacturing, which allowed for the generation of a metal lattice structure. An appropriate control and prototype were designed to minimize run time and material …

Manufacturing Process And Product Design For Mass Production Of Environmentally-Friendly Fishing Lures And Weights, David Ichlokmanian, Justin Jake Bert

Industrial and Manufacturing Engineering

The current industry standard for the manufacture of recreational fishing tackle uses lead-based weights and PVC or silicone-based lures. Both materials have serious negative effects on those who handle these products, waterfowl, fish, and other animals that may consume this discarded tackle. The goal of this project is to find and design an environmentally safe process and product alternative for this industry. To do this, we researched a large amount of viable safe materials for weights and lures and used decision matrices to decide on the best one. We found that brass would be the most suitable alternative and created …

Addressing The Existence Of Overcrowding In The Cal Poly Rec Center Exercise Rooms, Josue Alvarez, Robert Hemphill

Industrial and Manufacturing Engineering

Cal Poly’s Rec Center is a facility that has been extremely popular among students ever since its initial creation many decades ago. Despite its popularity being a positive quality in most ways, it does ultimately yield a certain issue for the users of the facility; the issue of overcrowding. This senior project aimed to analyze the problem of overcrowding at the Rec Center and improve upon its most critical areas of impact. Ultimately, we identified the Rec Center’s exercise rooms as the most impacted area, with the issue of equipment unavailability being the largest factor. Thus, we designed alternative equipment …

Design Of Standard Operating Procedures For Concrete Delivery And Pour Data Collection And Analysis, Andrew Willard, Mitchell Wilhelmsen

Industrial and Manufacturing Engineering

Webcor Concrete Group (WCG) is a self-perform subsidiary of Webcor Builders, a large general contractor in the state of California. Inefficiencies plague the construction industry, resulting in Webcor reaching out to the Cal Poly Industrial and Manufacturing Department and its students for help. The opportunity addressed in this report centers on a lack of concrete pour data collection. This gap results in a struggle to defend against, or pursue, backcharges with their concrete suppliers regarding additional labor costs or wasted material. The project objective is to provide WCG with a baseline data collection system and procedure, leading to increased back-charge …

Design For Waste Reduction And Efficiency Improvement For The Construction Usage Of The Tower Crane, George Merida, Roman Richard

Industrial and Manufacturing Engineering

Webcor Concrete Group’s on-site tower crane is currently experiencing unknown forms of inefficiency. The project team used the DMAIC methodology to implement Define, Measure, Analyze, Improve, and Control in order to guide and structure the project. After the project team formulated a problem statement, observations were collected of tower crane deliveries resulting in 470 individual data points. The data was then analyzed using basic statistics, histograms, and lean manufacturing tools in order to identify wastes and inefficiencies. Once the wastes and inefficiencies were identified, root cause analysis was performed. The identified root causes were then used as the basis for …

Designing An Information System To Efficiently Coordinate Film Screenings, Galen Dougherty

Industrial and Manufacturing Engineering

This paper explains the engineering concepts design efforts used to build an information system to efficiently coordinate film screenings. The market served is an emerging group of film makers and production companies that have limited resources. The application aims to save both time and money in coordination efforts for screening films in the local community. The project case examined is a small production start-up from Cal Poly San Luis Obispo named Yellow Glass Media. The design described in the paper specifically targets their needs which are assumed to be representative of the needs of the larger emerging market. The design …

Liquid Force Kite Control System Design, Brendan Kerr, Brodie Sutherland, Alden Simmer

Industrial and Manufacturing Engineering

Kiteboarding is an ocean sport wherein the participant, also known as a kiter, uses a large inflatable bow shaped kite to plane across the ocean on a surfboard or wakeboard. The rider is connected to his or her kite via a control bar system. This control system allows the kiter to steer the kite and add or remove power from the kite, in order to change direction and increase or decrease speed. This senior project focused on creating a new control bar system to replace a control bar system manufactured by a kiteboarding company, Liquid Force. The current Liquid Force …

Creating The Foundation For A Startup: Design And Implementation Of A Database System For An Electrical Bicycle Rental Company, Alejandro Martinez

Industrial and Manufacturing Engineering

BoltAbout was started by 4 Cal Poly students, and their COO is a fellow Industrial Engineering student that I met during the first half of the senior project series class. He presented the project to me and I decided to work with him in developing this new database for his startup company. BoltAbout’s customer base is growing and current operations are not fit to meet the demand of a growing company. More specifically, their data management system can’t be used by all current employees to perform essential tasks such as rental processing, bicycle and equipment organization, and customer data analysis. …

A Study Into The Production Efficiency Of Cal Poly Chocolates, Fernando Calderon

Industrial and Manufacturing Engineering

The project objective was to: identify ways to reduce the production cost of Cal Poly Chocolates. The project was executed through the DMAIC approach, a data driven improvement cycle. Using several industrial engineering tools, six improvement opportunities were found. Three project deliverables were created and three process changes were recommended. The total annual savings, if recommendations are implemented, sum to $1700.

Advances In Composite Manufacturing Of Helicopter Parts, Tobias A. Weber, Hans-Joachim K. Ruff-Stahl

International Journal of Aviation, Aeronautics, and Aerospace

This study investigates and compares different methods for improving standard autoclave composite manufacturing in order to find suitable approaches to a more efficient composite production. The goal is not only a reduction in manufacturing times and costs but also quality enhancement. Improved part quality while decreasing costs enables a manufacturer of composite parts to expand its market share, especially in the helicopter market, which has been constantly shrinking over the last two years. Various approaches such as improved tooling technology, the use of automated systems for lamination as well as outsourcing are examined to provide an overview of possible advancements …

Modeling Of Selective Laser Sintering/ Selective Laser Melting, Xuan Wang, Connor West

Industrial and Manufacturing Engineering

Selective laser sintering and selective laser melting are powder based additive manufacturing (AM) process that can rapidly manufacture parts with comparable mechanical properties to conventional manufacturing methods directly from digital files. However, the processing recipe development and design optimization of AM parts are often based on trial and error which erodes the benefit of AM. Modeling is a powerful tool to enable faster development cycle by significantly reducing the experimental efforts. In this paper we discussed the current status of selective laser sintering/melting modeling, in which the laser and powder interaction was studied to understand and predict the process and …

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …

Models For The Residual Life Of Railroad Bearing Grease In Laboratory And Industry Applications, Douglas Timmer, Constantine Tarawneh, Robert Jones

Manufacturing & Industrial Engineering Faculty Publications

Adequate lubrication in railroad bearings is crucial to the safe operation of these components. An investigation of the residual life of railroad bearing grease was conducted in a laboratory setting. The data was collected using a split-split-plot design of experiments. The Oxidation Induction Time (OIT), which is the time required for the remaining antioxidants in a sample of grease to be consumed in a test, is the response variable for this study. Low values of OIT indicate small remaining amounts of antioxidants in the grease and thus small remaining residual life in the grease. OIT measurements were made using differential …

Condition Assessment Of End-Of-Use Products For Remanufacturing, Jovan Morgan

Research Opportunities for Engineering Undergraduates (ROEU) Program 2016-17

The goal of the project is to use the automated 3-D laser scanner using a Capnut as a test object to detect surface defects, corrosion and calculation error through offline quality inspection. potentially reducing labor time and cost for both consumers and manufacturers.

Adaptive Scheduling For Operating Room Management, Honghan Ye

Theses and Dissertations--Mechanical and Aerospace Engineering

The perioperative process in hospitals can be modelled as a 3-stage no-wait flow shop. The utilization of OR units and the average waiting time of patients are related to makespan and total completion time, respectively. However, minimizations of makespan and total completion time are NP-hard and NP-complete. Consequently, achieving good effectiveness and efficiency is a challenge in no-wait flow shop scheduling. The average idle time (AIT) and current and future idle time (CFI) heuristics are proposed to minimize makespan and total completion time, respectively. To improve effectiveness, current idle times and future idle times are taken into consideration …

Chocolate Bar Wrapping Machine, Austin M. Hoff, Daniel R. Trepke, Caleb B. Krichbuam

Williams Honors College, Honors Research Projects

Gilbert Chocolates has proposed to manufacture a machine to wrap chocolate bars. This machine is intended to replace two people wrapping the chocolate bars by hand, which is a time consuming method. This is especially apparent between October and January when the workers are working long hours in preparation for the Christmas rush of customers. Currently wrapping a bar takes about a minute and Gilbert Chocolates wants this time reduced down to 20-30 seconds. The budget for this project is set at $1000, and is being funded by the company. This machine needs to fit in a cubic foot of …

Design And Implementation Of A Fixture For Robotic Welding, Isaac Nathaniel Williams

Industrial and Manufacturing Engineering

The Cal Poly IME department recently purchased a robotic welder. The faculty would like to see this robot incorporated into the welding class. The robot was capable of moving, but was not able to perform a weld prior to this project. This problem is addressed by creating a demonstration part for the welding class. The objectives that need to be complete for this to be possible is designing a part, designing a fixture, analyzing the cost of robotic welding, and implement welding the part in the class. The part is designed with specific requirements in mind. The fixture is designed …

Application Of Gearbox Drivetrains For Commuting Bicycles, Loren Sunding

Industrial and Manufacturing Engineering

People all over the world are beginning to ride their bicycles more often to destinations which include work, school, and local markets. Most bicycles being used for these activities have an external drivetrain exposed to the elements of the road including water, mud, dirt, and debris. External drivetrains are very fragile and when damaged, pedaling efficiency is greatly reduced and the overall riding experience diminishes.

One solution to this issue is a gearbox specifically designed for a bicycle frame. A gearbox has several mechanical mechanisms operating inside a protective housing. Since the housing is fully sealed, outside elements are not …

Assembly Line Kitting: Foam Mold Material Substitute, Samer Samy Saleh

Industrial and Manufacturing Engineering

Kitting is considered an incredibly innovative and effective solution intended to aid operators within a mixed model assembly line. However, it is a non-value added procedure and one that customers may not be willing to pay for. With this project, the goal is to examine opportunities to employ lean principles and provide a solution that further eliminates non-value added procedures, while also producing the potential for a flexible, mixed model assembly line.

To achieve the aforementioned purpose, the production of foam molds, located within industrial totes and sent to the assembly line, was found to be a major waste within …

Mri Upgrades At Radiology Associates, Patrick Cheung, Charlene Donlon

Industrial and Manufacturing Engineering

Problem Statement: The MRI machines at Radiology Associates are limiting the company’s ability to expand and compete within the local market. After discussing with technicians and managers at Radiology Associates, we decided to focus on hardware and software upgrades for the MRI machines. With 2 of the 3 locations purchasing new machines in the near future, our focus was on upgrades at the Santa Maria facility. The two machines at this location needed hardware and/or software upgrades to remain on par competitively both within the company and with local scanning options. Flexible coils are beneficial in terms of size, weight, …

Development Of A Process Monitoring Tool For The Manufacturing Process Of An Electric Vehicle Battery Enclosure, Ian Lamond

Industrial and Manufacturing Engineering

High volume manufacturing requires process control that is responsive to manufacturing related issues. It is critical that tools and resources are implemented that gauge manufacturing performance and identify root cause issues.

This project focuses on the design and manufacturing process of an electric vehicle aluminum battery enclosure and the implementation of a production measurement system. The current problem is a lack of process control communication and out of control alarms when uncontrolled events occur for manufacturing associates at the battery enclosure manufacturing work station.

This report examines the core principles of Quality Engineering, the economic advantages of implementing a vision …

Design And Prototyping Of An Adjustable Putter, Daulton Morgan

Industrial and Manufacturing Engineering

Being able to demo a golf putter is essential for a golfer since the feel of the putter is critical in determining what suits the golfer best. Due to the market being primarily dominated by right-handed players, it is difficult for left-handed players to demo high quality putters since the selection is sparse.

This report is about designing and integrating an interchangeable fastening system that allows a putter to be altered between a right and left-handed orientation, while still maintaining the traditional look of a putter. The report covers the necessary design steps, the prototyping of the putter, the projected …

The Effect Of Process Parameters And Surface Condition On Bond Strength Between Additively Manufactured Components And Polymer Substrates, Bharat Bhushan Chivukula

Graduate Theses and Dissertations

Additive patching is a process in which printers with multiple axes deposit molten material onto a pre-defined surface to form a bond. Studying the effect of surface roughness and process parameters selected for printing auxiliary part on the bond helps in improving the strength of the final component. Particularly, the influence of surface roughness, as established by adhesion theory, has not been evaluated in the framework of additive manufacturing (AM). A full factorial design of experiments with five replications was conducted on two levels and three factors, viz., layer thickness, surface roughness, and raster angle to examine the underlying effects …

Fatigue Analysis Of The Welded Region In The Automotive Torsion Beam Rear Suspension System, Nan Zhan, Xiaochuan Zhang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Technology Innovations And The Financial Services Industry., Olubukola Akinniyi Akinwunmi

Bullion

This article explores the future of the financial services industry in the context of new technologies. Technological innovations were reviewed and likely implications for the industry were highlighted. The article suggests that a symbiotic relationship among new and incumbent financial services providers will benefit the industry. Since technology is re-defining the financial services industry and the global financial system as undergone transformation in the last couple of decades.

Mechanisms And Solutions To The Brittle Solder Joint In Electroless Ni Plating, Xuan Wang, C. Key Chung

Industrial and Manufacturing Engineering

Brittle solder joints in Electroless Ni electroless Pd immersion Au (ENEPIG) surface finishes are one of the key reliability issues in electronics assembly. Previous characterization of the reflow process has indicated that interfacial voids formed after solder reflow are responsible for the decreases in solder joint strength. However, the mechanisms behind the formation of these voids in the ENEPIG process remain unclear. In this paper, the interaction between various aspects of the ENEPIG process and solder joint strength were investigated. Surface roughness, morphology, and nano-pitting at the interface between electroless Pd and Ni-P were characterized. The size and density of …

Design For Manufacturability: Off-Road Toyota Bumper, Drew Donlon

Industrial and Manufacturing Engineering

The purpose of this project is to design a new off-road bumper that is improved from the stock form of a 1996-2002 Toyota 4Runner and a 1996-2004 Toyota Tacoma. The current state of the component is too weak to endure to off-road endeavors, and a kit bumper market is virtually untapped for these vehicles. The objectives of this project were met by redesigning the stock front bumper, conducting a finite element analysis on the model to test for strength, prototyping the bumper with CNC cut cardboard, and conducting a full cost analysis including the costs for waterjet and laser cutting …

Gold Contamination In Non-Lead Surface Mount Solder Joints, Richard Alexander Garrison

Industrial and Manufacturing Engineering

Abstract

Solder joints are critical to the reliability of circuit boards. If gold is introduced to the solder joint, brittle AuSn4 intermetallic compounds develop which affect reliability of that solder joint. To determine the effects of gold when dissolved into a non-lead solder joint, a process was developed in order to apply gold content onto SAC305 solder paste. The gold was transferred as a paste from a micropipette onto each individual solder bump. This process was designed to apply a range of gold content from 1.0 wt. % to 10 wt. % to each individual solder joint. The test board …

Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning

Industrial and Manufacturing Engineering

The 3D printing industry has seen rapid growth in the last 10 years and has been called the next industrial revolution. There are several different processes used in 3D printing, but the most popular process is called Fused Filament Fabrication (FFF) or Fused Deposition Modeling (FDM). This is the process where (most commonly) plastic filament enters a nozzle, is heated to a semi-liquid state, and then deposited into a pattern to create a print. One major drawback to this process is that the prints are anisotropic. This means that the strength of the print varies with the orientation that it …

Design & Analysis Of A Bicycle Towing Device, Austin Lynch, William Max Mcewan, Fredrik Stenson

Industrial and Manufacturing Engineering

A local businessman had the idea to build a device that allows a bicycle to tow another bicycle. He built a prototype to demonstrate his idea but he wanted help in developing a product that could fit more bikes, did not require a rear rack to operate, and be manufacturable at his facility. He also expressed interest in an economic evaluation of production and marketing of the device. An analysis of customer needs led to adding reduction of weight and ease of attachment to the design requirements.

This report is about improving the original design and presents the process of …