Nuclear Engineering Commons^™

Radiation Transport Modeling Using Parallel Computational Techniques, William Culbreth

Reactor Campaign (TRP)

The Advanced Fuel Cycle Initiative (AFCI) program will rely on the use of accurate calculations and simulations of criticality and shielding for the separation process of the longlived isotopes that present a significant safety hazard in commercial spent fuel. To help design and verify the safety of the separation process, the neutronics code MCNPX will be used to model the distribution of neutron flux within the fuel blanket and to determine the neutron multiplication, k_eff. However, the cross section libraries and computational methods used by MCNPX at these neutron energies still have some uncertainty and will require validation. …

University Of Nevada, Las Vegas Transmutation Research Program Annual Report 2002, Anthony Hechanova, Elizabeth Johnson, Gary Cerefice

Transmutation Research Program Reports (TRP)

The UNLV Transmutation Research Program consists of four components: Program Support, Research Infrastructure Augmentation, International Collaboration, and Student Research.

In the first year of the program, the student research component was supported by the infrastructure augmentation and the program support components. In the second year of the program, the fourth leg of the support system, international collaborations, was added to the research support system.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Final Phase, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. This is the third and final phase of the study.

The first phase has resulted in improving the basic understanding of multipacting and the process of chemical etching. The second phase has resulted in an experimental setup …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of accelerator driven transmutation systems is the accelerator itself. To increase the efficiency of the high-power accelerators needed to support the transmutation mission, the national and international accelerator teams have proposed using elliptical superconducting niobium cavities. This project is tasked with examining the impacts of the design and fabrication technologies for these elliptical niobium cavities on their performance. Niobium was selected primarily due to its behavior at low temperatures.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of …

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Materials for transmuter systems must be able to tolerate high neutron fluxes, great temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge in that the corrosive behaviors of materials in LBE are not well understood. Most of the available information on LBE systems has come from the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found that the presence of small amounts of oxygen (on the order of parts per million) in the LBE significantly reduced corrosion. However, a fundamental understanding and verification of its …

Surface Studies Of Corrosion Of Stainless Steel By Lead Bismuth Eutectic, Daniel Koury, Brian D. Hosterman, John Farley, Dale L. Perry, D. Parsons, J. Manzerova, Allen L. Johnson

Transmutation Sciences Materials (TRP)

Why is Lead Bismuth Eutectic Important?

• Changing national security stances have led to reexamination of nuclear waste reprocessing

• Dangerous actinides can be separated and

• Transmuted into safer products, creating a waste form dangerous for only hundreds of years, in addition to the production (up to 1/3 of the original fission energy) of useful energy

• Non-moderating coolants or spallation targets for production of fast neutrons is required for transmutation

• Russian experience with LBE coolants in their nuclear submarine fleet makes LBE an attractive possible transmutation coolant technology

• Corrosion of steel by LBE is an important …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials, Ajit K. Roy, Brendan O'Toole, Zhiyong Wang, David W. Hatchett

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the potential for the environmentally-assisted cracking of candidate target materials for applications in spallation-neutron-target systems, such as accelerator-driven system for the transmutation of waste. The materials selected for evaluation and characterization are martensitic stainless steels (SS) including Alloys HT- 9, EP 823 and Type 422 stainless steel.

More recently, this experimental program has been expanded to evaluate the effect of molten lead-bismuth eutectic (LBE) on the corrosion behavior of target materials in the presence of oxygen. Since the materials performance laboratory (MPL) at UNLV currently cannot accommodate this type of testing, …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The corrosion of structural materials is a major concern for the use of lead-bismuth eutectic (LBE) systems for nuclear applications such as in transmuter targets or fast reactors. Corrosion in liquid metal systems can occur through various processes, including, for example, dissolution, formation of inter-metallic compounds at the interface, and penetration of liquid metal along grain boundaries. Predicting the rate of these processes depends on numerous system operational factors: temperature, system geometry, thermal gradients, solid and liquid compositions, and velocity of the liquid metal, to name a few. Corrosion, along with mechanical and/or hydraulic factors, often contributes to component failure. …

Modeling Of Corrosion In Oxygen Controlled Lead Bismuth Eutectic Systems With The Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen, Kanthi Kiran Dasika, Chao Wu

Transmutation Sciences Materials (TRP)

Objectives:

• To simulate a 2-D model of the Materials Test Loop by approximating it to be a toroid with a pie cross section for the purpose of comparing the simulated results with the analytical results.
• The temperature and concentration profiles on the wall boundaries imposed are similar to the actual test model.
• Geometry effects have great influence on local corrosion rate.
• A 2-D benchmark problem and a sudden expansion case are studied which show good consistency to analytical solution.
• Results from 2-D sudden expansion problem are similar to experimental data obtained by other researchers.

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this task is to evaluate the mechanical properties of Alloy EP-823 at temperatures relevant to the transmutation processes. Testing has been initiated to evaluate the tensile properties of martensitic Alloy EP-823 stainless steel at temperatures ranging from ambient (25 °C) to 600°C. The test materials were thermally treated prior to the evaluation of their tensile properties. The deformation characteristics of these tensile specimens, upon completion of testing, will be evaluated by surface analytical techniques such as scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Lead-bismuth eutectic (LBE) is a candidate as a spallation target in sub-critical transmutation systems and as a coolant in nuclear programs. One of the primary concerns with LBE systems is the corrosion of stainless steel, the primary structural material used in nuclear systems. To mitigate this problem, trace levels of oxygen can be introduced into the system, causing the formation of a protective oxide layer at the interface between the LBE and steel. To protect the steel components, this oxide layer must be properly maintained. However, too much oxygen will produce unwanted oxide precipitation within the coolant and elsewhere in …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

One of the greatest challenges in evaluating the performance of materials in the real world is the determination of residual stresses, or the stresses induced in a material. Plastic deformation of metals and alloys produces an increase in the number of lattice imperfections known as dislocations, which by virtue of their interaction results in higher state of internal stress and reduces ductility. These stresses, if not properly annealed (released) can significantly degrade the long-term performance of the materials.

Due to the high temperatures and radiation fields typically encountered in most nuclear systems, such as accelerator-driven transmutation systems (ADS) and nuclear …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation, Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

An innovative research program is proposed to investigate the corrosion of steel by lead alloys, and in particular lead-bismuth eutectic (LBE). In our previous work, some steels were found to be far more resistant to corrosion by LBE than others depending on surface preparation (cold working). This program would allow testing of crucial hypotheses about the causes of the observed increased corrosion resistance. We propose to build a new test facility at UNLV to expose steel samples to LBE as well as facilities to prepare steel samples as indicated by our work.

The unique capabilities of the test system will …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Carter D. Hull, Denis Beller

Transmutation Sciences Physics (TRP)

To optimize the performance of accelerator driven transmutation systems (ADS), engineers will need to design the system to operate with a neutron multiplication factor just below that of a critical, or self-sustaining, system. This design criteria requires particle transport codes that instill the highest level of confidence with minimal uncertainty, because the larger the uncertainties in the codes, the larger the safety margin required in the design and the lower the efficiency of the ADS transmuter. For current design efforts, the MCNPX code is used to determine neutron production and transport for spallation neutron systems.

While providing a very useful …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The first step in any transmutation strategy is the separation of radionuclides in used nuclear fuel. The current separation strategy supporting the Advanced Fuel Cycle Initiative (AFCI) program is based on the use of a solvent extraction separation process to separate the actinides, fission products, and uranium from used commercial nuclear fuel, and on the use of pyrochemical separation technologies to process used transmuter fuels. To separate the fission products and transuranic elements from the uranium in used fuel, the national program is developing a new solvent extraction process, the Uranium Extraction Plus, or UREX+, process, based on the traditional …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

The goal of this project is to investigate the casting processes for metallic fuels to help design a process that minimizes the loss of the volatile actinide elements from the fuel.

The research effort centers on the development of advanced numerical models to assess conditions that significantly impact the transport of volatile actinides during the melt casting process and represents a joint effort between researchers at the University of Nevada, Las Vegas (UNLV) and Argonne National Laboratory (ANL).

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project is to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models are developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment are also developed. Combined, these two models allow the assessment …

Design And Evaluation Of Processes For Transmuter Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

• Project Objective: examine autonomous robotic fuel fabrication processes with regard to hot cell and equipment design, operations, and costs.

• Fabrication processes for different fuel types differ in terms of equipment types, throughput, and cost.

• Design options are restricted by the requirement to employ only radiation-hardened machinery and components

• Benefit to Department of Energy: decision support for the selection of the most suitable manufacturing process.

A Finite Subelement Generalization Of The Variational Nodal Method, M. A. Smith, Nicholas Tsoulfanidis, E. E. Lewis, G. Palmiotti, T. A. Taiwo

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

The variational nodal method is generalized by dividing each spatial node into a number of triangular finite elements designated as subelements. the finite subelement trial functions allow for explicit geometry representations within each node, thus eliminating the need for nodal homogenization. the method is implemented within the Argonne National Laboratory code VARIANT and applied to two-dimensional multigroup problems. Eigenvalue and pin-power results are presented for a four-assembly Organization for Economic Cooperation and Development/Nuclear Energy Agency benchmark problem containing enriched UO2 and mixed oxide fuel pins. Our seven-group model combines spherical or simplified spherical harmonic approximations in angle with isoparametric linear …