Nuclear Engineering Commons^™

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2007 Through June 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. Modeling with different reacting flow channel configurations (ribbed-surface channels, hexagonal channels, and diamond-shaped channels) was performed. The probability of failure for the one channel geometry with different reacting flow channel configurations was calculated to be zero in the three principal directions for all of the cases.

• Bayonet Heat Exchanger. The Matlab code for calculating the probability of failure using a two-dimensional axisymmetric model of the bayonet decomposer was developed. The probability of failure was calculated for the inner and outer SiC walls, and the intermediate quartz wall of the decomposer and found to be …

Afci Quarterly Input – Unlv April 1 Through June 30, 2007, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Nevada Risk Assessment/Management Program (Nramp) – Phase 2: Quarterly Progress Report January 1, 2007 Through March 31, 2007, Klaus J. Stetzenbach

Nevada Risk Assessment/Management Program

Work conducted in this second quarter consisted of continuing the detailed data and information acquisition; review of the received document contents, and interpretation of significance in light of previous DOE documents. This included telephone and in-person discussions with DOE NVO personnel at the March Waste Management Symposia in Tucson. As a result of these discussions and review of the supporting data and methodologies, a more specific listing of activities was developed, and DOE provided a confirmatory note to HRC in March.

Much of the review of the received information does indicate significant changes in data, methodologies, and baseline assumptions over …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2007 Through March 31, 2007, Anthony Hechanova

Publications (NSTD)

• The variation of sulfur dioxide production (throughput) of the baseline design of the Ceramatec sulfuric acid decomposer with total mass flow rate of reacting flow has been calculated. According to the calculations, the sulfur dioxide production increases as the total mass flow rate of reacting flow increases regardless of the fact that decomposition percentage of sulfuric trioxide decreases. A parametric study of the baseline design of the Ceramatec sulfuric acid decomposer was performed.

• The thermal performance using various channel geometries for the decomposer was studied. The baseline design (straight channels) has 89.5% thermal efficiency while the thermal efficiency …

Afci Quarterly Input – Unlv January 1 Through March 31, 2007, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Nevada Risk Assessment/Management Program (Nramp) – Phase 2: Quarterly Progress Report, Oct. 1, 2006- Dec. 31, 2006, Klaus J. Stetzenbach

Nevada Risk Assessment/Management Program

Work conducted in this initial period consisted of work start-up (technical, administrative, contractual), and interviewing/site visits with DOE NVO staff (and support contractors) and HRC staff to quickly ascertain current technical activities and priorities as related to the scope of this task.

Since much of the technical work scope builds on previous technical work, it was considered critical to determine the changes (programmatic, technical, and regulatory) that have occurred over the past several years that directly relate to the scope. It was also equally important to determine the technical and programmatic priorities that have been established in the interim.

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2006 Through December 31, 2006, Anthony Hechanova

Publications (NSTD)

Modifications to the single-channel models of the Ceramatec heat exchanger and decomposer concept for hexagonal flow channels under two values of layer-overlapping (50% and 100%) and for diamond-shaped flow channels were completed.

The finite element calculations of the “Ball on Three Ball Test” for ceramic material for the purpose of selecting the appropriate specimen thickness for future experimental testing was performed for plate thicknesses ranging from 2 to 8 mm.

A finite element model of the “Ball on Three Ball Test” was also studied for discs having micro-channels.

Decoupling And Disturbance Rejection Control For Target Circulation, Jian Ma, Joon S. Lee, Woosoon Yim

Reactor Campaign (TRP)

In 1998, the Institute of Physics and Power Engineering (IPPE) and Experimental and Development Organization “Gidropress” in Russia, began the design and construction of a prototype lead-bismuth eutectic (LBE) accelerator target, the Target Complex 1 (TC-1), under the International Science and Technology Center (ISTC) project #559 (“Pilot Flow Lead-Bismuth Target of 1 MW Power for Accelerator Driven Systems”) in support of the international efforts to develop accelerator-driven spallation systems for nuclear transmutation and other applications.

During the thermal and engineering test of the TC-1 in 2005 at UNLV, it was observed that the existing control algorithm led to a very …

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used in a number of nuclear energy related applications, such as circulation of molten lead-bismuth eutectic alloys in neutron targets, and circulation of liquid sodium metal in Gen IV Sodium-cooled Fast Reactors (SFR). Because EM pumps have no moving parts which can fail, they are considerably more reliable than conventional mechanical pumps for molten metal usage, and thus EM pumps are favored over mechanical pumps even though their pumping efficiency is lower and their initial cost is higher when compared to mechanical pumps of similar flow rates.

The research objectives of this task are:

• A …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven system (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure and temperature environment, no accurate local flow measurement technique is readily available. Electromagnetic (EM) flow meter is popular in low temperature application as it is a non-intrusive technology. However, additional voltage will be produced due to temperature, flow, pressure, the chemical properties of the liquid metal and surface condition of the steel walls. In addition, the non-definite wetting behavior of liquid lead-bismuth to the electrically …

University Of Nevada, Las Vegas Transmutation Research Program Annual Report Academic Year 2006-2007, Anthony Hechanova, Rebecca Arbour

Transmutation Research Program Reports (TRP)

It is my pleasure to present the UNLV Transmutation Research Program’s sixth annual report that highlights the academic year 2006-2007. Supporting this document are the many technical reports and theses that have been generated over the past five years.

In the sixth year of our program, we continued to see growth in the Radiochemistry Ph.D. program with a total of 13 students in the third year of the program (we anticipated eight in the program proposal). Since our inception, the program has sponsored to their conclusion 42 M.S. and 4 Ph.D. degrees. The program supported 39 graduate students, 17 undergraduates, …

Combined Radiation Detection Methods For Assay Of Higher Actinides In Separation Processes, Denis Beller, Warnick Kernan

Safeguards Campaign (TRP)

The ultimate objective of this project is to develop technology to detect and accurately measure quantities of higher actinides in processing systems without taking frequent samples. These systems include used fuel receipt, separations batches, and pipelines. A variety of measurements may be combined to calculate flow rates of actinide elements with a to-be-determined precision. Nuclear and decay characteristics of materials during processing will be acquired, conceptual designs of monitoring systems will be developed, radiation transport studies will be conducted to develop an understanding of operational regimes, and experiments will be performed to confirm performance. Radiation transport and scoping studies will …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

During the past academic year, this project was focused on the characterization of residual stress in welded specimens consisting of austenitic and martensitic stainless steels using an activation technique based on the Positron Annihilation Spectroscopic (PAS) method. The extent of residual stress was expressed in terms of three line-shape parameters (S-, W- and T-). Further, efforts were made to characterize linear lattice defects such as dislocations in the vicinity of Fusion-Line (FL), Heat-Affected- Zone (HAZ), and the base material of the welded specimens using Transmission Electron Microscopy (TEM). The metallurgical microstructures at these three regions have also been evaluated by …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry Morphology, And Surface Preparation, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Advanced nuclear processes and facilities (e.g., transmutation of nuclear waste, fast reactors, and spallation neutron sources) impose special demands on materials, which must withstand high temperatures, high radiation fields, and chemical corrosion. Proposed schemes for transmuting nuclear waste require a nonmoderating coolant such as lead-bismuth eutectic (LBE). While LBE corrodes most steels, small amounts of oxygen in the LBE greatly reduces the corrosion rate, and could ideally re-grow a damaged oxide layer in-situ. The protective oxide layer would thus be self-healing. However, the fundamental understanding of the role of oxygen and passivating oxide layers is presently incomplete.

During the present …

Effect Of Silicon Content On The Corrosion Resistance And Radiation- Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is focused on the evaluation of the effects of silicon content on both the corrosion behavior and radiation-induced embrittlement of martensitic stainless steels having compositions similar to that of modified 9Cr-1Mo steel, also known as T91 grade steel. T91 grade steel was selected to be a candidate structural material to contain molten lead-bismuth eutectic (LBE), which can act both as a target material and a coolant during the spallation process. The operating temperature during this process may range from 420-550 °C. Thus, moderate tensile strength of the containment material (T91) is a major requirement.

The beneficial effects of …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Jinsuo Zhang, Jichun Li

Transmutation Sciences Materials (TRP)

The goal of the proposed research project is to provide basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead-alloys (lead or lead-bismuth eutectic) coolant systems. Precise studies and simulations of all hydrodynamics with thermal conditions encountered in practical coolant loop systems by use of different flowing conditions in the laboratory are difficult and expensive, if not impossible. Therefore it is important and necessary to develop theoretical models to predict the protective oxide layer behaviors at the design stage of a practical lead-alloy coolant system, to properly interpret and apply …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead-bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive to …

Development Of Integrated Process Simulation System Model For Spent Fuel Treatment Facility (Sftf) Design, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The major objectives will lead to a creation of framework that combines all the strengths of AMUSE’s complicated calculations, well-established commercial system process package and ISOPro’s flexible parameter optimization modules. Development of the process simulation code can be done using the solvent extraction process at Argonne National Laboratory in collaboration with the research team from Mechanical Engineering Department at UNLV.

Research accomplishments:

• Integrated the ASPEN-Plus process model with the ISOPro system engineering modeling package, developed by the UNLV team.
• Tested the simplified system process integration using the ISOPro package.
• Generated complete version of the ISOPro package user manual and tutorial. …

Separation Of Technetium From Uranium And Waste Form Synthesis, Kenneth Czerwinski

Waste Forms Campaign (TRP)

In this project, systematic investigations on the Tc-Zr binary metal system will be evaluated for the first time. The synthesis of metallic Tc as well as its alloys with Zr will be evaluated. In order to provide valuable data to AFC R&D, the thermodynamic equilibrium phases, as well as their performance under repository conditions, will be examined.

Evaluation Of Cs/Sr Waste Form For Long Term Storage And Disposal, Gary Cerefice, Longzhou Ma

Waste Forms Campaign (TRP)

The goal of this project is to examine two potential concerns regarding the long-term performance of a proposed cesium/ strontium waste form. To facilitate long-term storage, up to 300 years, the disposal containers will need to be able to survive for the entire storage interval. The first aspect of the project will explore the potential interaction of the aluminosilicate waste form with the storage canister materials to determine if there is any corrosion or chemical interaction concerns for the storage of the materials.

At the end of the storage interval, most of the 137Cs in the waste form will have …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing, Georg F. Mauer

Fuels Campaign (TRP)

The safe and effective manufacturing of actinide-bearing fuels for any transmutation strategy requires that the entire manufacturing process be contained within a shielded hot cell environment. To ensure that the fabrication process is feasible, the entire process must be designed for remote operation. The equipment must be reliable enough to perform over several decades, and also easy to maintain or repair remotely. The facility must also be designed to facilitate its own decontamination and decommissioning. In addition to these design factors, the potential viability of any fuel fabrication process will also be impacted by a number of variables, such as …

Impact Of The Synthesis Process On Structure Properties For Afci Fuel Candidates, Kenneth Czerwinski

Fuels Campaign (TRP)

Synthesis of actinium mononitrides using carbothermic reduction of the corresponding oxides has a few outstanding issues, including the formation of secondary phases such as oxides and carbides and low densities of the final product. Furthermore the requirement of a high process temperature at 1700°C, for more than 12 hours is also a drawback particularly for Americium-bearing samples. Therefore, it is important to explore the use of other possible routes to synthesize actinide mononitrides.

A low temperature process is used in this research to produce actinide mononitrides using a fluoride route in which the first step is to mix the actinide …

Solution-Based Synthesis Of Nitride Fuels, Tyler A. Sullens, Kenneth Czerwinski

Fuels Campaign (TRP)

The preliminary studies into the synthesis of actinide nitride fuels through a low temperature, liquid ammonia based synthesis route have been conducted on the uranium containing system, and there is good indication for the success of synthesizing uranium (III) nitride. The dissolution of iodine in ammonia is a rapid process, resulting in a pale green solution, which does not result in any observable oxidation of iodine. The cannula transfer of dissolved iodine into the reaction vessel containing U metal has been conducted with little to no residual iodine remaining in the original flask. The metal being used for these reactions …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

This project focuses on the chemical bonding and interface formation of metal fission products with the coating materials used in tri-isotropic (TRISO) fuel particles for gas-cooled reactors. By combining surface- and bulk-sensitive spectroscopic methods, intermediate chemical phases at the interface, intermixing/ diffusion behavior, and the electronic interface structure as a function of material (metal and coating materials) and temperature are examined.

In the past year, emphasis was placed on a detailed analysis and description of the Cs/SiC interface formation process.

Reactor Physics Studies For The Afci Reactor-Accelerator Coupling Experiments Project, Denis Beller

Transmutation Sciences Physics (TRP)

The specific research objective of this three-year project is to design and conduct accelerator driven experiments, which will help demonstrate in the U.S. the ability to design, compute, and conduct ADSS experiments and to predict and measure source importance, coupling efficiency, sub-critical reactor kinetics and source-driven transients. In addition, databases will be created for both steady state and transient ADSS experiments for the nuclear community to develop and test new computational codes and methods, and the importance of a driving neutron source in various regions of different subcritical assemblies will be mapped. Experiments will be conducted and compared to calculations …

Afci Quarterly Input – Unlv October 1 Through December 31, 2006, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2006 Through September 30, 2006, Anthony Hechanova

Publications (NSTD)

Hydrodynamics and thermal numerical modeling coupled with sulfur trioxide decomposition for the one channel geometry with three different channel configurations were performed. The results obtained from the numerical modeling were compared with the baseline design under the same boundary and operation conditions. The case with diamond shaped channels has the highest percentage of sulfuric acid decomposition. The baseline channel geometry has the lowest pressure drop compared with other cases.

Afci Quarterly Input – Unlv July 1 Through September 30, 2006, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2006 Through June 30, 2006, Anthony Hechanova

Publications (NSTD)

Numerical Analyses of the Ceramatec Sulfuric Acid Decomposer. Comparisons with experiments for the Ceramatec sulfuric acid decomposer coupon with eight straight channels for four different geometries and four different flow rates were performed. All of the operation and boundary conditions for the calculations were the same as in the Ceramatec experiments. Good agreement was found. The overall pressure drop difference between calculations and experiments for most of the cases is within 10%.