Nuclear Engineering Commons^™

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Second Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Microscale Polymeric Helical Structures Produced By Electrospinning, Royal Kessick, Gary C. Tepper

Mechanical and Nuclear Engineering Publications

Microscale helical coils consisting of a composite of one conducting and one nonconducting polymer were produced using electrospinning. The nonconducting polymer was poly(ethylene oxide) and the conducting polymer was poly(aniline sulfonic acid). The coil structures were studied over a range of processing conditions and fiber composition. The data suggest that the helical structures are formed due to viscoelastic contraction upon partial neutralization of the charged fibers. Polymeric microcoils may find applications in microelectromechanical systems, advanced optical components, and drug delivery systems.

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Lead-bismuth eutectic (LBE) is a candidate as a spallation target in sub-critical transmutation systems and as a coolant in nuclear programs. One of the primary concerns with LBE systems is the corrosion of stainless steel, the primary structural material used in nuclear systems. To mitigate this problem, trace levels of oxygen can be introduced into the system, causing the formation of a protective oxide layer at the interface between the LBE and steel. To protect the steel components, this oxide layer must be properly maintained. However, too much oxygen will produce unwanted oxide precipitation within the coolant and elsewhere in …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of acceleratordriven transmutation systems is the accelerator itself. Elliptical superconducting niobium cavities are used to increase the efficiency of the high-power accelerators needed to support the transmutation mission.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of electrons. This phenomenon limits the maximum amount of energy and power that the niobium cavity can store. As a result, the maximum power available for accelerating the desired charge, as well as the overall performance of the accelerator is reduced. Furthermore, …

Chemical Kinetics And Thermal Hydraulics Of Lead Bismuth Flow Loops, Kanthi Kiran Dasika

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of the thesis is to study the effect of chemical kinetics and thermal hydraulics of Lead Bismuth Eutectic (LBE) flow in the Materials Test Loop (MTL). The Materials Test Loop, also known as the Delta Loop, was built in Los Alamos National Laboratories (LANL) to obtain the experimental data for corrosion estimation and analysis. It is a well-known fact that corrosion plays an important role in the design of nuclear thermal hydraulic systems. Since the MTL is a multi-section closed system that differs in diameter from one part to another, an intensive study on the overall and regional …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Aug. 01 – Oct. 31, 2003), Yingtao Jiang, Bingmei Fu

Transmutation Sciences Materials (TRP)

The experimental setup designed and manufactured in UNLV was shipped to LANL in early Aug. One student has been working in LANL to conduct the experiment since then. In the meantime, one new Ph. D. student has started to run the simulation for transport in oxygen mixing. In Oct., a professional has been hired to work in both experimental and the theoretical studies pertaining to the proposed work.

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 01 – August 31, 2003), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed (bent), and welded materials using a nondestructive method based on positron annihilation spectroscopy (PAS). This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens that could not be accomplished by conventional positron technique or other nondestructive methods. The generated …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (May. 01 – July 31, 2003), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

The report for Y01 has been prepared and submitted. The final part of our apparatus, the N3Si4 stirrer, was received by the end of May. The assembly of the apparatus has almost been completed. The control plan for our apparatus has been revised. To run FLUENT, a high-end Unix-based Sun workstation has been acquired. Plan has been made to ship our apparatus to LANL.

Development Of Advanced High Temperature Heat Exchangers: Proposal, University Of Nevada, Las Vegas. Research Foundation

Publications (NSTD)

A research team led by the University of Nevada, Las Vegas (UNLV) Research Foundation proposes a project to develop advanced high temperature heat exchangers (HTHX) for hydrogen production and electrical energy conversion from advanced nuclear reactor concepts. This project will also support the development of Generation IV reactors. The research team includes researchers from UNLV, General Atomics (GA), Sandia National Laboratories (SNL), The University of California, Berkeley UCB) and Oak Ridge National Laboratory (ORNL).

The proposed project will be administered by the University of Nevada Las Vegas Research Foundation (UNLVRF). UNLVRF will provide the overall contract administration and is the …

Study Of Geometric Effects On Local Corrosion Rates For Lbe Loop, Chao Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Corrosion is an extremely important issue in nuclear cooling system applications. Many scientific and engineering efforts have been contributed to the research of finding an ideal material, which has resistance to corrosive Lead Bismuth Eutectic (LBE). A Delta Loop was designed and constructed in Los Alamos National Lab (LANL) to obtain the experimental data. This loop is a multi-section closed system that differs in diameter from one part to another. As a result, an intensive study on the geometry effect is hence necessary and valuable. In this thesis, this problem was simulated by commercial software STAR-CD. Results provide a good …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii Final Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The second phase has resulted in an experimental setup of a fluid flow experiment with experimentation to be completed in the third year. Some of these results were presented at American Nuclear Society, Student Conference April 2-5, …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Feb. 01 – Apr. 30, 2003), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

We received most of the components, everything except the customized and outsourced stirrer, for the new apparatus for oxygen measurement/calibration. Thus far, most of the machining work has been completed. The LaveView module used for the data collection and the control of the apparatus has been tested. 2-D simulation work has been performed using FEMLAB.

Modeling, Fabrication, And Optimization Of Niobium Cavities Phase Ii: Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The second phase has resulted in an experimental setup of a fluid flow experiment with experimentation to be completed in the third year. Other experimental activities include the evaluation of a vacuum system and various vacuum equipment …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to insure that their knowledge and experience benefits the project. The research to be conducted during year three will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this third year is to …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Nov. 01 – Jan. 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

The design of the new apparatus for oxygen measurement/calibration has been completed. This new apparatus shall be of great importance for the UNLV researchers to conduct the research work in the campus.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Final Phase, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. This is the third and final phase of the study.

The first phase has resulted in improving the basic understanding of multipacting and the process of chemical etching. The second phase has resulted in an experimental setup …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of accelerator driven transmutation systems is the accelerator itself. To increase the efficiency of the high-power accelerators needed to support the transmutation mission, the national and international accelerator teams have proposed using elliptical superconducting niobium cavities. This project is tasked with examining the impacts of the design and fabrication technologies for these elliptical niobium cavities on their performance. Niobium was selected primarily due to its behavior at low temperatures.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Lead-bismuth eutectic (LBE) is a candidate as a spallation target in sub-critical transmutation systems and as a coolant in nuclear programs. One of the primary concerns with LBE systems is the corrosion of stainless steel, the primary structural material used in nuclear systems. To mitigate this problem, trace levels of oxygen can be introduced into the system, causing the formation of a protective oxide layer at the interface between the LBE and steel. To protect the steel components, this oxide layer must be properly maintained. However, too much oxygen will produce unwanted oxide precipitation within the coolant and elsewhere in …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Aug. 01 – Oct. 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

After two month intensive work in LANL, some preliminary sensor calibration curves have been obtained. Further data analysis shall be performed to assess the theoretical and measured data. Also, a new experimental apparatus shall be designed and located in UNLV to continue the left work.

Technical Progress:

• A set of calibration curves of voltage vs. temperature ranging from 300⁰C to 500⁰C under various oxygen concentrations in liquid LBE for the YSZ oxygen sensor has been obtained and has been reported in one paper.

• A meeting with LBE committee and other faculty members in AAA …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Multipacting is one of the major loss mechanisms in rf superconductivity cavities for accelerators. This loss mechanism limits the maximum amount of energy/power supported by the cavities. Optimal designs have been identified in others’ studies. In practice, these designs are not easily manufactured. Chemical etching processes used to polish the cavity walls result in a nonuniform surface etch. A nonuniform surface etch will leave some unclean areas with contaminants and micron size particles. These significantly affect mutipacting. Further, a nonuniform etch will leave areas with damaged grain structure, which is not good for superconducting properties. Typically, the depth of chemical …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 1 – August 31, 2002), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed, and welded materials using a nondestructive method based on positron annihilation spectroscopy. This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens, that could not be accomplished by conventional positron technique or other nondestructive methods. The generated data will …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …

Modeling And Simulation Of The Chemical Etching Process In Niobium Cavities, Qin Xue

UNLV Theses, Dissertations, Professional Papers, and Capstones

Niobium Cavities are important parts of the integrated NC/SC high-power linear accelerator (linac) that can accelerate over 100 mA of protons to several GeV. Surface finish of the niobium cavity plays an important role of achieving the best performance of niobium cavity. The chemical etching techniques have been widely used.

Chemical etching of the inner surface of the cavity is achieved by circulating acid through it. The acid interacts with the surface and eliminates imperfections. During the etching process, a pipe with baffles is inserted within the cavity to direct the flow along the surfaces.

A 2-D, axisymmetric, steady state, …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (May 01 – July 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Accurate measurement of the oxygen concentration in liquid Lead-Bismuth Eutectic (LBE) cooling system is critical in the active control of the corrosion at the interface between LBE and the stainless steel of transport tubes. Currently, LANL (Los Alamos National Laboratory) scientists have employed an automobile-style YSZ (Yttria Stabilized Zirconia) oxygen sensor unit to measure oxygen levels in an engineeringscaled LBE test system. Although the theoretical model for calculating oxygen concentration based on voltage measurement of YSZ sensor in static conditions is well understood, there is an urgent and strong need to obtain a complete set of calibration curves for YSZ …

Development Of A Model For Induction Heating, Randy Clarksean, Yitung Chen

Fuels Campaign (TRP)

There are two coupled equations that must be solved in order to determine the power deposition. The numerical solution of these equations is needed in order to apply a source term within the energy equations. These equations have previously solved in FIDAP. That implementation used modified versions of the momentum and energy equations to provide a mechanism for the solution of two coupled equations. Currently, we want to solve for the induction heating field in addition to the flow field and the energy equation. In order to do this, a mechanism has to be defined within FIDAP to solve these …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to ensure that their knowledge and experience benefits the project. The research to be conducted during the second year will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this second year is …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces led to the use of a buffered chemical polishing procedure for surface cleaning to get good performance of the cavities. This proposal discusses the second phase of research in the second year of the project.

The first phase (starting Summer 2001) has resulted in improving the basic understanding of multipacting and the process of chemical etching. Based …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada, Las Vegas (UNLV) and Idaho State University (ISU) is to evaluate the feasibility of determining residual stresses of welded (after pre-straining) engineering materials using a new nondestructive technique based on positron annihilation spectroscopy. The proposed technique is to use γ-rays 2 from a small MeV electron Linac to generate positrons inside the sample via pair production. This method can be used for materials characterization and investigation of defects in thick samples that could not be accomplished by conventional positron techniques or other nondestructive methods. The data generated will …

Modeling, Fabrication, And Optimization Of Niobium Cavities – Phase I: Quarterly Progress Report November 20, 2001 - February 20, 2002, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Multipacting is one of the major loss mechanisms in RF superconductivity cavities for accelerators. This loss mechanism limits the maximum amount of energy/power supported by the cavities. Optimal designs have been identified in others’ studies. In practice, these designs are not easily manufactured. Chemical etching processes used to polish the cavity walls result in a nonuniform surface etch. A nonuniform surface etch will leave some unclean areas with contaminants and micron size particles. These significantly affect multipacting. Further, a nonuniform etch will leave areas with damaged grain structure, which is not good for superconducting properties. Typically, the depth of chemical …