Nuclear Engineering Commons^™

Hydrothermal Preparation Of Gd+3 -Doped Titanate Nanotubes: Magnetic Properties And Photovoltaic Performance, Hoda S. Hafez, M Saif, James T. Mcleskey Jr., M.S.A. Abdel-Mottaleb, I S. Yahia, T Story, W Knoff

Mechanical and Nuclear Engineering Publications

Pure and Gd+3 -doped titanate nanotubes (TNTs) materials were synthesized by a hydrothermal method. Their morphology, optical properties, thermal stability, and magnetic properties were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), UV-Vis spectroscopy, thermal analysis, and magnetic measurements. It was found that doping renders Gd+3-TNT visible light active and results in smaller crystallite size and larger surface area as well as higher thermal stability compared to pure titanate nanotubes. The estimated magnetic moments point to presence of weak antiferromagnetic interaction. Application of the prepared Gd+3-TNT for modifying conventional photoanodes in polymer solar cells was attempted. Preliminary results show …

Nanostructured Solid-State Hybrid Photovoltaic Cells Fabricated By Electrostatic Layer-By-Layer Deposition, Rolf Kniprath, James T. Mcleskey Jr., Jürgen P. Rabe, Stefan Kirstein

Mechanical and Nuclear Engineering Publications

We report on the fabrication of hybrid organic/inorganic photovoltaic cells utilizing layer-by-layer deposition of water-soluble polyions and nanocrystals. A bulk heterojunction structure was created consisting of alternating layers of the p-conductive polythiophene derivative poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] and n-conductive TiO2nanoparticles. We fabricated working devices with the heterostructure sandwiched between suitable charge carrier blocking layers and conducting oxide and metal electrodes, respectively. We analyzed the influence of the thickness and nanostructure of the active layer on the cell performance and characterized the devices in terms of static and transient current response with respect to illumination and voltage conditions. We observed reproducible and stable photovoltaic …

A Realistic Modeling Of Fluid Infiltration In Thin Fibrous Sheets, Sudhakar Jaganathan, Hooman Vahedi Tafreshi, Behnam Pourdeyhimi

Mechanical and Nuclear Engineering Publications

In this paper, a modeling study is presented to simulate the fluid infiltration in fibrous media. The Richards’ equation of two-phase flow in porous media is used here to model the fluid absorption in unsaturated/partially saturated fibrous thin sheets. The required consecutive equations, relative permeability, and capillary pressure as functions of medium’s saturation are obtained via fiber-level modeling and a long-column experiment, respectively. Our relative permeability calculations are based on solving the Stokes flow equations in partially saturated three-dimensional domains obtained by imaging the sheets’ microstructures. The Richards’ equation, together with the above consecutive correlations, is solved for fibrous media …

Criticality Studies Of Actinides Within Fissures, Trevor Wilcox

UNLV Theses, Dissertations, Professional Papers, and Capstones

The storage of nuclear waste in underground storage facilities presents numerous engineering challenges and risks. Experimental verification of engineered underground storage is impractical or prohibitively expensive, leaving scientists with few options. A 1995 report by Bowman and Venneri of the Los Alamos National Laboratory generated considerable controversy by hypothesizing that wastes composed of fissionable plutonium leached from underground storage containers could pose a nuclear criticality hazard. They proposed cases where plutonium collected in underground fractures could lead to sustained nuclear fission. In overmoderated cases, they argued that the resulting release of energy from fission could result in steam explosions, or …

Oxidation Modeling By Means Of Molecular Dynamics, Chaiyod Soontrapa

UNLV Theses, Dissertations, Professional Papers, and Capstones

Oxidation modeling is normally engineered to study systems at macroscopic scales, mostly in analytical forms based on diffusion theories. The associated time scale is usually in months, days, or minutes, and the length scale is in the order of microns. In this dissertation, oxidation modeling is performed at atomistic scale with the time and length scales in picoseconds and angstroms, respectively, using molecular dynamics. Molecular dynamics simulations generate trajectories of each atom or particle in a system according to the laws of physics. Studying oxidations under the atomistic point of view can offer new insights on atomic behaviors and influencing …

High Temperature Heat Exchanger Annual Report, Anthony Hechanova

Publications (NSTD)

Objectives

• Identify candidate materials for heat exchanger components.

• Test candidate materials for heat exchanger components.

• Design critical components in the interface between the reactor and hydrogen production plant and within the sulfur iodine thermochemical process.

• Fabricate prototypical components.

• Test prototypical components.

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/material interactions pose a critical barrier for higher temperature and longer core life designs. For advanced burner reactors (sodium cooled) such as EBR-II and FFTF, experience has shown that the qualified structural materials and fuel cladding severely limits the economic performance. In other liquid metal cooled reactor concepts, advanced materials and better understanding and control of coolant and materials interactions are necessary for realizing the potentials.

Liquid sodium has been selected as the primary coolant candidate for Gen. IV nuclear energy systems. Global Nuclear Partnership (GNEP) Advanced Burned Reactor (ABR) has …

Correlation Of Tellurium Inclusions And Carrier Lifetime In Detector Grade Cadmium Zinc Telluride, Ezzat S. Elshazly, Gary C. Tepper

Mechanical and Nuclear Engineering Publications

Carrier lifetimes and telluriuminclusion densities in detector grade cadmiumzinc telluride crystals grown by the high pressure Bridgman method were optically measured using pulsed laser microwavecavity perturbation and infrared microscopy. Excess carriers were produced in the material using a pulsed laser with a wavelength of 1064 nm and pulse width of 7 ns, and the electronic decay was measured at room temperature. Spatial mapping of lifetimes and defect densities in cadmiumzinc telluride was performed to determine the relationship between telluriumdefect density and trapping. A strong correlation was found between the volume fraction of telluriuminclusions and the carrier trapping time.

Electrokinetic Separation Of Co-Solutes Into Bimodal Fibers By Electrospinning, Chunya Wu, Shinobu Nagata, Gary C. Tepper, James T. Mcleskey Jr.

Mechanical and Nuclear Engineering Publications

Composite and chemically/physically distinct fibers of sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] (PTEBS) and polyethylene oxide (PEO) were formed by electrospinning from a homogeneous aqueous solution containing PTEBS and PEO co-solutes. Composite nanofibers of diameter of ∼60nm were electrospun from an aqueous solution. The addition of ammonium hydroxide (NH4OH) to the water solution resulted in “bimodal” electrospun fibers consisting of distinct large diameter white PEO fiber segments and small diameter black PTEBS fiber segments. The optical absorptionspectrum of the composite PTEBS/PEO nanofibers did not exhibit the characteristic peak around 460nm, which is present in the bulk spectrum.

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook, Yitung Chen, Jian Ma

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used extensively in current and proposed nuclear power systems and industrial molten metal transfer operations. Although the Magnetohydrodynamic (MHD) theory that underlies the operation of these types of pumps has been studied extensively in the past few decades, the design of specific EM pumping systems for specific flow cases requires computational tools and expertise, which is lacking in the U.S. However, for the past two years, researchers at UNLV have been utilizing the TC-1 liquid metal loop system at UNLV and an Annular Linear Induction Pump (ALIP) to drive the liquid metal and to develop …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang, Jian Ma

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven systems (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure, and temperature environment, the existing flow measurement techniques (such as Electromagnetic flow meters, Ultrasonic flow meters, Turbine flow meters, etc.) are not accurate and reliable.

The measurement of flow rates (mass flow rates or volume flow rate) plays a notable role in monitoring and controlling the experimental conditions. The bulk flow rates can be obtained through direct methods, which measure the amount of discharged fluids …

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/ material interactions pose a critical barrier for higher temperature and longer core life designs. For sodium-cooled fast reactors (SFRs) such as the Experimental Breeder Reactors in Idaho and the Fast Flux Test Facility in Hanford, experience has shown that qualified structural materials and fuel cladding severely limits their economic performance.

Liquid sodium has been selected as the primary coolant candidate for the Advanced Burner Reactor (ABR) of the Global Nuclear Partnership (GNEP). Materials improvement has been identified as a major thrust to improve fast reactor economics. Researchers from universities, national …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2007 Through September 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. The numerical model of a SiC ceramic coupon with two layers of microchannels was developed. Calculations of the factor of safety and probability of failure for the case of a straight channel were performed. Results for a pressure of 7.5 MPa were performed. The thermal and mechanical stress analyses of the Ceramatec HTHX and decomposer were completed.

• Bayonet Heat Exchanger. The thermal and mechanical stress analyses of the bayonet type HTHX and decomposer (Sandia design) were completed. Temperature profiles obtained from thermocouples measured from the Sandia experiments have been applied to the whole packed …

Unlv Research Foundation High Temperature Heat Exchanger Development: 9/08, Anthony Hechanova

Publications (NSTD)

Barriers addressed:

Nuclear Hydrogen Initiative R&D Plan – Material performance and component design and testing for the intermediate heat exchanger and high-temperature thermochemical water splitting (H₂SO₄ decomposition and HI decomposition). Improved materials for High Temperature Electrolysis.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2007 Through June 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. Modeling with different reacting flow channel configurations (ribbed-surface channels, hexagonal channels, and diamond-shaped channels) was performed. The probability of failure for the one channel geometry with different reacting flow channel configurations was calculated to be zero in the three principal directions for all of the cases.

• Bayonet Heat Exchanger. The Matlab code for calculating the probability of failure using a two-dimensional axisymmetric model of the bayonet decomposer was developed. The probability of failure was calculated for the inner and outer SiC walls, and the intermediate quartz wall of the decomposer and found to be …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2007 Through March 31, 2007, Anthony Hechanova

Publications (NSTD)

• The variation of sulfur dioxide production (throughput) of the baseline design of the Ceramatec sulfuric acid decomposer with total mass flow rate of reacting flow has been calculated. According to the calculations, the sulfur dioxide production increases as the total mass flow rate of reacting flow increases regardless of the fact that decomposition percentage of sulfuric trioxide decreases. A parametric study of the baseline design of the Ceramatec sulfuric acid decomposer was performed.

• The thermal performance using various channel geometries for the decomposer was studied. The baseline design (straight channels) has 89.5% thermal efficiency while the thermal efficiency …

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2006 Through December 31, 2006, Anthony Hechanova

Publications (NSTD)

Modifications to the single-channel models of the Ceramatec heat exchanger and decomposer concept for hexagonal flow channels under two values of layer-overlapping (50% and 100%) and for diamond-shaped flow channels were completed.

The finite element calculations of the “Ball on Three Ball Test” for ceramic material for the purpose of selecting the appropriate specimen thickness for future experimental testing was performed for plate thicknesses ranging from 2 to 8 mm.

A finite element model of the “Ball on Three Ball Test” was also studied for discs having micro-channels.

Geometrical Modeling Of Fibrous Materials Under Compression, Benoit Maze, Hooman Vahedi Tafreshi, Behnam Pourdeyhimi

Mechanical and Nuclear Engineering Publications

Many fibrous materials such as nonwovens are consolidated via compaction rolls in a so-called calendering process. Hot rolls compress the fiber assembly and cause fiber-to-fiber bonding resulting in a strong yet porous structure. In this paper, we describe an algorithm for generating three dimensional virtual fiberwebs and simulating the geometrical changes that happen to the structure during the calendering process. Fibers are assumed to be continuous filaments with square cross sections lying randomly in the x or y direction. The fibers are assumed to be flexible to allow bending over one another during the compression process. Lateral displacement is not …

An Electrospray-Based, Ozone-Free Air Purification Technology, Gary Tepper, Royal Kessick, Dmitry Pestov

Mechanical and Nuclear Engineering Publications

A zero-pressure-drop, ozone-free air purification technology is reported. Contaminated air was directed into a chamber containing an array of electrospray wick sources. The electrospray sources produce an aerosol of tiny, electrically charged aqueous droplets.Charge was transferred from the droplets onto polar and polarizable species in the contaminated air stream and the chargedcontaminants were extracted using an electric field and deposited onto a metal surface. Purified air emerged from the other end of the chamber. The very small aqueous electrospray droplets completely evaporate so that the process is essentially dry and no liquid solvent is collected or recirculated. The air purification …

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used in a number of nuclear energy related applications, such as circulation of molten lead-bismuth eutectic alloys in neutron targets, and circulation of liquid sodium metal in Gen IV Sodium-cooled Fast Reactors (SFR). Because EM pumps have no moving parts which can fail, they are considerably more reliable than conventional mechanical pumps for molten metal usage, and thus EM pumps are favored over mechanical pumps even though their pumping efficiency is lower and their initial cost is higher when compared to mechanical pumps of similar flow rates.

The research objectives of this task are:

• A …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven system (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure and temperature environment, no accurate local flow measurement technique is readily available. Electromagnetic (EM) flow meter is popular in low temperature application as it is a non-intrusive technology. However, additional voltage will be produced due to temperature, flow, pressure, the chemical properties of the liquid metal and surface condition of the steel walls. In addition, the non-definite wetting behavior of liquid lead-bismuth to the electrically …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2006 Through September 30, 2006, Anthony Hechanova

Publications (NSTD)

Hydrodynamics and thermal numerical modeling coupled with sulfur trioxide decomposition for the one channel geometry with three different channel configurations were performed. The results obtained from the numerical modeling were compared with the baseline design under the same boundary and operation conditions. The case with diamond shaped channels has the highest percentage of sulfuric acid decomposition. The baseline channel geometry has the lowest pressure drop compared with other cases.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2006 Through June 30, 2006, Anthony Hechanova

Publications (NSTD)

Numerical Analyses of the Ceramatec Sulfuric Acid Decomposer. Comparisons with experiments for the Ceramatec sulfuric acid decomposer coupon with eight straight channels for four different geometries and four different flow rates were performed. All of the operation and boundary conditions for the calculations were the same as in the Ceramatec experiments. Good agreement was found. The overall pressure drop difference between calculations and experiments for most of the cases is within 10%.

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2006 Through March 31, 2006, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The UNLVRF HTHX Project quarterly meeting was held in Albuquerque, NM, March 16 and 17, 2006. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. A tour of Sandia National Laboratory was also provided that included a visit to their sulfuric acid decomposition test apparatus. There were 24 attendees from universities, national laboratories, and private industry. Collaborators discussed their research progress. The next meeting will be in July in Salt Lake City, UT.

Unlv Research Foundation High Temperature Heat Exchanger Development, Anthony Hechanova

Publications (NSTD)

Barriers addressed:

Nuclear Hydrogen Initiative R&D Plan – Material performance and component design and testing for: intermediate heat exchanger and high-temperature thermochemical water splitting (H2SO4 decomposition and HI decomposition). Improved materials for High Temperature Electrolysis.

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2005 Through December 31, 2005, Anthony Hechanova

Publications (NSTD)

• Liquid Salt Technical Working Group Meeting. The first meeting of the Liquid Salt Technical Working Group was held on October 28, 2005 at the Pratt Whitney Rocketdyne facility in Canoga Park, CA. 20 experts from academia, industry, and national laboratories participated to discuss current state of knowledge and research needs for high temperature liquid salt applications.
• Nuclear Hydrogen Initiative Semi-annual Review. Several participants from the UNLVRF University Consortium gave technical presentations at the NHI Semi-annual Review meeting in Rockville, MD, November 9-10, 2005.
• Quarterly Collaboration Meeting. The University of Nevada, Las Vegas hosted a UNLVRF HTHX Project quarterly meeting December …

Hybrid Solar Cells From Water-Soluble Polymers, James T. Mcleskey Jr., Qiquan Qiao

Mechanical and Nuclear Engineering Publications

We report on the use of a water-soluble, light-absorbing polythiophene polymer to fabricate novel photovoltaic devices. The polymer is a water-soluble thiophene known as sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] or PTEBS. The intention is to take advantage of the properties of conjugated polymers (flexible, tunable, and easy to process) and incorporate the additional benefits of water solubility (easily controlled evaporation rates and environmentally friendly). The PTEBS polythiophene has shown significant photovoltaic response and has been found to be effective for making solar cells. To date, solar cells in three different configurations have been produced: titanium dioxide (TiO2) bilayer cells, TiO2 bulk heterojunction solar …

Cracking Of Martensitic Alloy Ep-823 Under Controlled Potential, Ajit K. Roy, M. K. Hossain

Mechanical Engineering Faculty Research

The susceptibility of martensitic Alloy EP-823 to stress corrosion cracking was evaluated with and without an applied cathodic potential using the slow-strain-rate (SSR) testing technique. The magnitude of the applied potential was based on the corrosion potential determined by cyclic polarization. The cracking susceptibility in an acidic environment at different temperatures was expressed in terms of the true failure stress (ơ_f), time to failure (TTF), and ductility parameters, including percent elongation (%El) and percent reduction in area (%RA). The data indicate that the magnitudes of ơ_r, TTF, %El, and %RA were reduced due to cathodic charging. …