Nuclear Engineering Commons^™

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials, Ajit K. Roy, Brendan O'Toole, Zhiyong Wang, David W. Hatchett

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the potential for the environmentally-assisted cracking of candidate target materials for applications in spallation-neutron-target systems, such as accelerator-driven system for the transmutation of waste. The materials selected for evaluation and characterization are martensitic stainless steels (SS) including Alloys HT- 9, EP 823 and Type 422 stainless steel.

More recently, this experimental program has been expanded to evaluate the effect of molten lead-bismuth eutectic (LBE) on the corrosion behavior of target materials in the presence of oxygen. Since the materials performance laboratory (MPL) at UNLV currently cannot accommodate this type of testing, …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The corrosion of structural materials is a major concern for the use of lead-bismuth eutectic (LBE) systems for nuclear applications such as in transmuter targets or fast reactors. Corrosion in liquid metal systems can occur through various processes, including, for example, dissolution, formation of inter-metallic compounds at the interface, and penetration of liquid metal along grain boundaries. Predicting the rate of these processes depends on numerous system operational factors: temperature, system geometry, thermal gradients, solid and liquid compositions, and velocity of the liquid metal, to name a few. Corrosion, along with mechanical and/or hydraulic factors, often contributes to component failure. …

Modeling Of Corrosion In Oxygen Controlled Lead Bismuth Eutectic Systems With The Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen, Kanthi Kiran Dasika, Chao Wu

Transmutation Sciences Materials (TRP)

Objectives:

• To simulate a 2-D model of the Materials Test Loop by approximating it to be a toroid with a pie cross section for the purpose of comparing the simulated results with the analytical results.
• The temperature and concentration profiles on the wall boundaries imposed are similar to the actual test model.
• Geometry effects have great influence on local corrosion rate.
• A 2-D benchmark problem and a sudden expansion case are studied which show good consistency to analytical solution.
• Results from 2-D sudden expansion problem are similar to experimental data obtained by other researchers.

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this task is to evaluate the mechanical properties of Alloy EP-823 at temperatures relevant to the transmutation processes. Testing has been initiated to evaluate the tensile properties of martensitic Alloy EP-823 stainless steel at temperatures ranging from ambient (25 °C) to 600°C. The test materials were thermally treated prior to the evaluation of their tensile properties. The deformation characteristics of these tensile specimens, upon completion of testing, will be evaluated by surface analytical techniques such as scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Lead-bismuth eutectic (LBE) is a candidate as a spallation target in sub-critical transmutation systems and as a coolant in nuclear programs. One of the primary concerns with LBE systems is the corrosion of stainless steel, the primary structural material used in nuclear systems. To mitigate this problem, trace levels of oxygen can be introduced into the system, causing the formation of a protective oxide layer at the interface between the LBE and steel. To protect the steel components, this oxide layer must be properly maintained. However, too much oxygen will produce unwanted oxide precipitation within the coolant and elsewhere in …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

One of the greatest challenges in evaluating the performance of materials in the real world is the determination of residual stresses, or the stresses induced in a material. Plastic deformation of metals and alloys produces an increase in the number of lattice imperfections known as dislocations, which by virtue of their interaction results in higher state of internal stress and reduces ductility. These stresses, if not properly annealed (released) can significantly degrade the long-term performance of the materials.

Due to the high temperatures and radiation fields typically encountered in most nuclear systems, such as accelerator-driven transmutation systems (ADS) and nuclear …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation, Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

An innovative research program is proposed to investigate the corrosion of steel by lead alloys, and in particular lead-bismuth eutectic (LBE). In our previous work, some steels were found to be far more resistant to corrosion by LBE than others depending on surface preparation (cold working). This program would allow testing of crucial hypotheses about the causes of the observed increased corrosion resistance. We propose to build a new test facility at UNLV to expose steel samples to LBE as well as facilities to prepare steel samples as indicated by our work.

The unique capabilities of the test system will …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Carter D. Hull, Denis Beller

Transmutation Sciences Physics (TRP)

To optimize the performance of accelerator driven transmutation systems (ADS), engineers will need to design the system to operate with a neutron multiplication factor just below that of a critical, or self-sustaining, system. This design criteria requires particle transport codes that instill the highest level of confidence with minimal uncertainty, because the larger the uncertainties in the codes, the larger the safety margin required in the design and the lower the efficiency of the ADS transmuter. For current design efforts, the MCNPX code is used to determine neutron production and transport for spallation neutron systems.

While providing a very useful …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The first step in any transmutation strategy is the separation of radionuclides in used nuclear fuel. The current separation strategy supporting the Advanced Fuel Cycle Initiative (AFCI) program is based on the use of a solvent extraction separation process to separate the actinides, fission products, and uranium from used commercial nuclear fuel, and on the use of pyrochemical separation technologies to process used transmuter fuels. To separate the fission products and transuranic elements from the uranium in used fuel, the national program is developing a new solvent extraction process, the Uranium Extraction Plus, or UREX+, process, based on the traditional …

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project is to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models are developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment are also developed. Combined, these two models allow the assessment …

Design And Evaluation Of Processes For Transmuter Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

• Project Objective: examine autonomous robotic fuel fabrication processes with regard to hot cell and equipment design, operations, and costs.

• Fabrication processes for different fuel types differ in terms of equipment types, throughput, and cost.

• Design options are restricted by the requirement to employ only radiation-hardened machinery and components

• Benefit to Department of Energy: decision support for the selection of the most suitable manufacturing process.

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 8/16/02- 11/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

Two activities are proposed in this Phase I task: the development of a systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Aug. 01 – Oct. 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

After two month intensive work in LANL, some preliminary sensor calibration curves have been obtained. Further data analysis shall be performed to assess the theoretical and measured data. Also, a new experimental apparatus shall be designed and located in UNLV to continue the left work.

Technical Progress:

• A set of calibration curves of voltage vs. temperature ranging from 300⁰C to 500⁰C under various oxygen concentrations in liquid LBE for the YSZ oxygen sensor has been obtained and has been reported in one paper.

• A meeting with LBE committee and other faculty members in AAA …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823 For Transmutation Applications: Annual Progress Report (September 2001 – August 2002), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this project is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. This alloy has been proven to be an excellent structural material to contain the lead-bismuth-eutectic (LBE) nuclear coolant needed for fast spectrum operations. Very little data exist in the open literature on the tensile properties of this alloy. The test material will be thermally treated prior to the evaluation of its tensile properties at temperatures relevant to the transmutation applications. The deformation characteristics of tensile specimens, upon completion of testing, will be evaluated by surface …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

The AAA program is developing technology for the transmutation of nuclear waste to address many of the long-term disposal issues. An integral part of this program is the proposed chemical separations scheme. This process, as envisioned by Argonne National Laboratory (ANL) researchers, will be outlined later in this report.

Nearly all issues related to risks to future generations arising from long-term disposal of such spent nuclear fuel is attributable to ~1% of its content. This 1% is made up primarily of plutonium, neptunium, americium, and curium (the transuranic elements) and long-lived isotopes of iodine and technetium created as products from …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems: Quarterly Progress Report (June 01 – August 31, 2002), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate target materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including Alloy HT-9, Alloy EP 823 and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these materials are being evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. Further, the localized corrosion behavior of these alloys …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 1 – August 31, 2002), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed, and welded materials using a nondestructive method based on positron annihilation spectroscopy. This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens, that could not be accomplished by conventional positron technique or other nondestructive methods. The generated data will …

Design And Evaluation Of Processes For Fuel Fabrication: Year 1 Final Report, Georg F. Mauer

Fuels Campaign (TRP)

The project objective is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. The year 1 project was focused …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Final Report -Phase I 09/01/2001-08/30/2002, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 5/16/02- 8/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

Two activities are proposed in this Phase I task: the development of systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral to …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (May 01 – July 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Accurate measurement of the oxygen concentration in liquid Lead-Bismuth Eutectic (LBE) cooling system is critical in the active control of the corrosion at the interface between LBE and the stainless steel of transport tubes. Currently, LANL (Los Alamos National Laboratory) scientists have employed an automobile-style YSZ (Yttria Stabilized Zirconia) oxygen sensor unit to measure oxygen levels in an engineeringscaled LBE test system. Although the theoretical model for calculating oxygen concentration based on voltage measurement of YSZ sensor in static conditions is well understood, there is an urgent and strong need to obtain a complete set of calibration curves for YSZ …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems: Annual Progress Report (May 2001 – May 2002), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate target materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including Alloy HT-9, Alloy EP 823 and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these materials are being evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. Further, the localized corrosion behavior of these alloys …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823: Aaa Task-10 Quarterly (03/01, 2002 –05/31, 2002) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The objective of this task is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. The test material will be thermally treated prior to evaluation of its tensile properties at temperatures relevant to the transmutation applications. The deformation characteristics of tensile specimens, upon completion of testing, will be evaluated by surface analytical techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The overall results are expected to provide a mechanistic understanding of high-temperature deformation behavior of Alloy EP-823 as a function of heat treatment.

Highlights of Accomplishment

• …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Quarterly Progress Report 03/16/02- 06/15/02, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with very limited density. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high oxygen concentration, …

Development Of A Model For Induction Heating, Randy Clarksean, Yitung Chen

Fuels Campaign (TRP)

There are two coupled equations that must be solved in order to determine the power deposition. The numerical solution of these equations is needed in order to apply a source term within the energy equations. These equations have previously solved in FIDAP. That implementation used modified versions of the momentum and energy equations to provide a mechanism for the solution of two coupled equations. Currently, we want to solve for the induction heating field in addition to the flow field and the energy equation. In order to do this, a mechanism has to be defined within FIDAP to solve these …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Phase Two, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The proposed work will combine chemical kinetics and hydrodynamics in target and test-loop lead-bismuth eutectic (LBE) systems to model system corrosion effects. This approach will result in a predicative tool that can be validated with corrosion test data, used to systematically design tests and interpret the results, and provide guidance for optimization in LBE system designs. The task includes two subtasks. The first subtask is to try to develop the necessary predictive tools to be able to predict the levels of oxygen and corrosion products close to the boundary layer through the use of Computational Fluid Dynamics (CFD) modeling. The …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Darrell Pepper, Randy Clarksean

Separations Campaign (TRP)

Two activities are proposed: the development of a systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model will be the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project will streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral to the systems engineering model. …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823 For Transmutation Applications, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this project is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. This alloy has been proven to be an excellent structural material to contain the lead-bismuth-eutectic (LBE) nuclear coolant needed for fast spectrum operations. However, very little data exist in the open literature on the tensile properties of this alloy. The selection of Alloy EP-823 as the test material in the proposed task is based on the recommendation of our collaborator at the Los Alamos National Laboratory (LANL). The test material will be thermally treated prior …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 2/16/02- 5/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

Two activities are proposed in this Phase I task: the development of systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral to …