Nanoscience and Nanotechnology Commons^™

Effect Of Surface Omniphobicity On Drying By Forced Convection, Madani A. Khan, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Low energy surfaces can strongly repel both oil and water. Recently these surfaces have been fabricated on various substrates including fabric, aluminum, stainless steel and many other materials. In this experiment we explore the use of low energy surface deposition on aluminum alloy, stainless steel and silicon substrates, to enhance the drying rate of liquids removed from the surface by forced convection. We control surface roughness by substrate abrasion and by the growth of Al₂O₃ nanograss to enhance liquid repellence by use of a hierarchical texture. Liquid repellence of the substrates is measured by contact angles of …

An Estimate Of The Second-Order In-Plane Acceleration Sensitivity Of A Y-Cut Quartz Thickness-Shear Resonator, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

We perform a theoretical analysis of the second-order in-plane acceleration sensitivity of a Y-cut quartz thick-ness-shear mode resonator. The second-order nonlinear theory of elasticity for anisotropic crystals is used to determine the biasing fields in the resonator under in-plane acceleration. The acceleration-induced frequency shift is determined from a per-turbation analysis based on the plate equations for small-amplitude vibrations superposed on a finite bias. We show that, whereas the first-order acceleration-induced frequency shift is zero for a structurally symmetric resonator under in-plane ac-celeration, the second-order frequency shift is nonzero and is quadratic in the acceleration. As the fourth-order nonlinear elastic constants …

Three-Dimensional Scaffolds Of Graphene, Carbon Nanotubes And Transition-Metal Oxides For Applications In Electronics, Sensors And Energy Storage, Gilbert N. Mbah

Department of Chemistry: Dissertations, Theses, and Student Research

Electronics, sensors and energy storage devices are the new waves behind economic development, security and communication¹. Engineering small sizes of electronic, sensors and energy storage devices is the hurdle limiting efficient, portable and vast applications of Nano-devices for economic, security and communication advancement². Silicon the major material used in transistors has approached its limit to fabricated Nano-devices³. The discovery of free standing, one atomic layer thick and two-dimensional graphene sheets with high conductivity, inert, high specific surface area, stable and high tensile strength material in 2004 has shown capabilities to replaced silicon in electronics, …

Wet Chemical Synthesis And Characterization Of Nanomaterials For Solar Cell Applications, Krystle N. Sy, Ramprasad Gandhiraman, Jessica E. Koehne

STAR Program Research Presentations

During long term space missions, it is necessary to have a reliable source of energy. Solar cells are an easy and reliable way to convert energy from the sun to electrical energy. NASA has used solar cells manufactured on Earth as an energy source for many of its missions. In order to develop technologies that will enable high efficiency solar cells, we are synthesizing nanostructured materials. A range of nanostructured materials, such as titanium dioxide nanowires, nickel nanoparticles, copper nanoparticles, and silver nanoparticles/nanowires, are synthesized. In this work, we are reporting on the synthesis of these nanomaterials and the electron …

Biodegradable Medical Device Having An Adjustable Degradation Rate And Methods Of Making The Same, Yuebin Guo, Michael Sealy, Meisam Salahshoor Pirsoltan

Department of Mechanical and Materials Engineering: Faculty Publications

Disclosed herein are biodegradable medical devices comprising biodegradable material (e.g., magnesium-calcium alloys) having an adjustable rate of degradation that can be used in various applications, including, but not limited to, drug delivery applications, cardiovascular applications, and orthopedic applications to make biodegradable and biocompatible devices. Also disclosed herein are methods of making biodegradable medical devices comprising biodegradable materials by using, for instance, hybrid dry cutting/hydrostatic burnishing.

Spotlight On Graphene Research From The Middle East, Kathleen A. Lehman

University Libraries Faculty Publications and Presentations

In an extension to the 2011 article “Reviews of Science for Science Librarians: Graphene” (Lehman 2011), this paper seeks to continue exploring the trend of graphene research but limits its focus to the research production of countries in the Middle East. In addition to reporting on the research output of this group of countries, this article will also examine the most prolific Middle Eastern graphene authors,their supporting institutions and funding agencies, the most cited publications from this group, the journals most used for publication of their work, and the general trend in graphene research growth in the Middle East. As …

Traction-Separation Relationships For Hydrogen-Induced Grain Boundary Embrittlement In Nickel Via Molecular Dynamics Simulations, Wesley Allen Barrows

Graduate Theses and Dissertations

The deleterious effects of atomic and molecular hydrogen on the mechanical properties of metals have long been observed. Although several theories exist describing the mechanisms by which hydrogen negatively influences the failure of materials, a consensus has yet to be reached regarding the exact mechanism or combination of mechanisms. Two mechanisms have gained support in explaining hydrogen’s degradative role in non-hydride forming metals: hydrogen-enhanced localized plasticity and hydrogen-enhanced decohesion. Yet, the interplay between these mechanisms and microstructure in metallic materials has not been explained. Accordingly, for this thesis, the three main objectives are: (i) to develop a numerical methodology to …

Nanoformulation For Anticancer Drug Delivery: Enhanced Pharmacokinetics And Circulation, Gaurav Parekh

Doctoral Dissertations

In this study, we have explored the application of the Layer-by-Layer (LbL) assembly technique for improving injectable drug delivery systems of low soluble anticancer drugs (e.g. Camptothecin (CPT), Paclitaxel (PTX) or Doxorubicin (DOX)). For this study, a polyelectrolyte shell encapsulates different types of drug nanocores (e.g. soft core, nanomicelle or solid lipid nanocores).The low soluble drugs tend to crystallize and precipitate in an aqueous medium. This is the reason they cannot be injected and may have low concentrations and low circulation time in the blood. Even though these drugs when present in the cancer microenvironment have high anti-tumor inhibition, the …

Nanoenhanced Additive Manufacturing: Additive Introduction Onto Halloysite Nanotubes And Into 3d Printing Filament For Tailored Material Characteristics, James Connor Nicholson

Doctoral Dissertations

With the rapid advancement of additive manufacturing technologies in recent years on both the microscale and the macroscale, research must be done to test the limits of currently available technologies. On the microscale, halloysite nanotubes have proven to be a viable platform for reinforcement of polymers and time release of loaded chemicals, as well as a substrate material for the deposition of nanoparticles. The range of materials are limited due to polarity conflicts, and often lead to wet chemical processes that use more toxic alternatives. Three-dimensional (3D) printing and macroscale additive manufacturing techniques can be used to generate custom structures, …

Fabrication Of Sub-10 Nm Metallic Structures Via Nanomasking Technique For Plasmonic Enhancement Applications, Stephen Joseph Bauman

Graduate Theses and Dissertations

One area of nanoscience that has become popular in recent years is the study of optics at the nanoscale. Due to enhanced fabrication techniques, new geometries and improved dimensional resolutions have been allowing the creation of nanostructures for use in this area. Nanoscale geometries cause unique optical effects such as enhancement of the signal’s electric field strength at the surface of a substrate. Specifically, structures separated by nanogaps (10 nm and smaller) have been shown to exhibit strong field enhancement within the gaps. This has opened up the potential for surface enhanced spectroscopies, enhanced absorption for photovoltaics, and improved sensing …

Fabrication And Material Characterization Of Copper And Copper-Cnt Micropillars, Siavash Ghanbari, Jeff Darabi

SIUE Faculty Research, Scholarship, and Creative Activity

In this work, copper micropillars and copper-carbon nanotube (CNT) composite micropillars were fabricated by incorporating an electrodeposition technique with a xurography process. In order to disperse carbon nanotubes in copper-CNT micropillars, various amounts of CNTs were added to the electroplating bath. Surface morphology and phase characterization of copper micropillars and copper-CNT composite micropillars were analyzed by optical microscopy and X-ray diffraction. In addition, the corrosion resistance (R_p) of a bare copper substrate, copper micropillars, and optimum copper-CNT micropillars were studied by electrochemical impedance spectroscopy (EIS) technique in a 3.5 wt. % sodium chloride. Experimental results yielded a corrosion …

Surface Modification Of Noble Metal Nanostructures Toward Biomedical Applications, Samir V. Jenkins

Graduate Theses and Dissertations

Noble metal nanostructures have seen a steady increase in biomedical application over the last several decades; new diagnostic and therapeutic modalities are under intense investigation. Many of these applications are possible because of post-synthetic modifications to the particle surface. These modifications take a variety of forms and can significantly affect the pharmacokinetics of these particles. In this work, various surface modifications were investigated. Particle agglomeration, which occurs when particle surfaces remain in contact, can significantly affect the toxicity and efficacy of a nanomedicine. Darkfield microscopy and single-particle ICP-MS were developed as complementary methods to detect agglomeration in blood, with the …

Synthesis Of Palladium And Palladium-Copper Nanostructures As Electrocatalysts, Haibin Wu

Graduate Theses and Dissertations

Pd and its alloys are alternatives of Pt as promising catalysts and electrocatalysts for many reactions. Size controlled synthesis of nanoparticles remains a major research subject, since smaller size particles show better catalytic performance. In this work, we developed a modified chemical wet method to prepare Pd and Pd-Cu nanostructures with uniform small size. Different sizes and shapes of Pd nanostructures were successfully synthesized by using the two reducing agents (i.e., L-ascorbyl-6-palmitate or phenylphosphinic acid). The reducing agents play a role to control the final morphologies and sizes of particles. The use of L-ascorbyl-6-palmitate favors to form irregular branch shapes …

Development And Characterization Of Intermediate-Band Quantum Wire Solar Cells, Colin Stuart Furrow

Graduate Theses and Dissertations

The effects of a quantum wire intermediate band, grown by molecular beam epitaxy, on the optical and electrical properties of solar cells are reported. To investigate the behavior of the intermediate band, the quantum wires were remotely doped at three different doping concentrations, the number of quantum wire layers was varied from three to twenty, and the solar cell structure was optimized. For all the structures, current-voltage and external quantum efficiency measurements were performed to examine the effect of absorption and power conversion of the intermediate band solar cell (IBSC). Time-resolved photoluminescence measurements showed that δ-doping can increase the lifetime …

Engineering The Ground State Of Complex Oxides, Derek Joseph Meyers

Graduate Theses and Dissertations

Transition metal oxides featuring strong electron-electron interactions have been at the forefront of condensed matter physics research in the past few decades due to the myriad of novel and exciting phases derived from their competing interactions. Beyond their numerous intriguing properties displayed in the bulk they have also shown to be quite susceptible to externally applied perturbation in various forms. The dominant theme of this work is the exploration of three emerging methods for engineering the ground states of these materials to access both their applicability and their deficiencies.

The first of the three methods involves a relatively new set …

Energy Harvesting-Aware Design For Wireless Nanonetworks, Shahram Mohrehkesh

Computer Science Theses & Dissertations

Nanotechnology advancement promises to enable a new era of computing and communication devices by shifting micro scale chip design to nano scale chip design. Nanonetworks are envisioned as artifacts of nanotechnology in the domain of networking and communication. These networks will consist of nodes of nanometer to micrometer in size, with a communication range up to 1 meter. These nodes could be used in various biomedical, industrial, and environmental monitoring applications, where a nanoscale level of sensing, monitoring, control and communication is required. The special characteristics of nanonetworks require the revisiting of network design. More specifically, nanoscale limitations, new paradigms …

Nano Scale Mechanical Analysis Of Biomaterials Using Atomic Force Microscopy, Diganta Dutta

Mechanical & Aerospace Engineering Theses & Dissertations

The atomic force microscope (AFM) is a probe-based microscope that uses nanoscale and structural imaging where high resolution is desired. AFM has also been used in mechanical, electrical, and thermal engineering applications. This unique technique provides vital local material properties like the modulus of elasticity, hardness, surface potential, Hamaker constant, and the surface charge density from force versus displacement curve. Therefore, AFM was used to measure both the diameter and mechanical properties of the collagen nanostraws in human costal cartilage. Human costal cartilage forms a bridge between the sternum and bony ribs. The chest wall of some humans is deformed …

Broadband High Efficiency Fractal-Like And Diverse Geometry Silicon Nanowire Arrays For Photovoltaic Applications, Omar Hassan Al-Zoubi

Graduate Theses and Dissertations

Solar energy has many advantages over conventional sources of energy. It is abundant, clean and sustainable. One way to convert solar energy directly into electrical energy is by using the photovoltaic solar cells (PVSC). Despite PVSC are becoming economically competitive, they still have high cost and low light to electricity conversion efficiency. Therefore, increasing the efficiency and reducing the cost are key elements for producing economically more competitive PVSC that would have significant impact on energy market and saving environment. A significant percentage of the PVSC cost is due to the materials cost. For that, thin films PVSC have been …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Non-Wetting Surface-Driven High-Aspect-Ratio Crystalline Grain Growth For Efficient Hybrid Perovskite Solar Cells, Cheng Bi, Qi Wang, Yongbo Yuan, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Large-aspect-ratio grains are needed in polycrystalline thin-film solar cells for reduced charge recombination at grain boundaries; however, the grain size in organolead trihalide perovskite (OTP) films is generally limited by the film thickness. Here we report the growth of OTP grains with high average aspect ratio of 2.3–7.9 on a wide range of non-wetting hole transport layers (HTLs), which increase nucleus spacing by suppressing heterogeneous nucleation and facilitate grain boundary migration in grain growth by imposing less drag force. The reduced grain boundary area and improved crystallinity dramatically reduce the charge recombination in OTP thin films to the level in …

Computer Simulations Of Propulsion Of Self-Propelled Flexible Nanobody, Ye Luo

Masters Theses

Swimming bodies such as flagellum and fishes are found everywhere in liquid environment. The research of simulation of swimmers is one of the most important branches among the field of biophysics. This study focus on the direct computer simulation of self-propelled flexible nanobody in fluid field. Two new objectives is studied based on the previous research of Tai-hsien Wu and Dewei ai (2014)[1]. ln Wu's article, the front end of micro swimming body is fixed and the migration of swimmers is neglected. For a further study, one of new targets is to release the head in 3-D simulation fluid area. …

Measuring The Effectiveness Of Photoresponsive Nanocomposite Coatings On Aircraft Windshields To Mitigate Laser Intensity, Ryan S. Phillips, Hubert K. Bilan, Zachary X. Widel, Randal J. Demik, Samantha J. Brain, Matthew Moy, Charles Crowder, Stanley L. Harriman, James T. O'Malley Iii, Joseph E. Burlas, Steven F. Emmert, Jason J. Keleher

Journal of Aviation Technology and Engineering

In 2004, pilots reported 46 laser illumination events to the Federal Aviation Administration (FAA), with the number increasing to approximately 3,600 in 2011. Since that time, the number of reported laser incidents has ranged from 3,500 to 4,000. Previous studies indicate the potential for flight crewmember distraction from bright laser light being introduced to the cockpit. Compositional variations of the photoresponsive nanocomposite coatings were applied to an aircraft windscreen using a modified liquid dispersion/heating curing process. The attenuating effects of the deposited films on laser light intensity were evaluated using an optical power meter and the resultant laser intensity data …

Resonant Spectra Of Metal Nanotoroids Of Various Sizes, Huong Quynh Tran

Electrical Engineering Undergraduate Honors Theses

Nowadays, the manipulation of light by using metallic nanostructures has wide applications in photonics, optoelectronics and energy conversion. Along with other universities all over the world, the University of Arkansas is researching on nano-antennas’ design, fabrication and applications. Current research in Dr. El-Shenawee’s Terahertz Imaging and Spectroscopy Computational Electromagnetics Group, has computationally investigated the behaviors of plasmonic nanostructures by using the commercial finite element electromagnetic solver Ansys® HFSS. This work reproduced the previous work of spectral absorption enhancement of infinite and finite arrays of silver and gold nanotoroids with sizes of the inner radii: 13nm – 21nm, while outer radius …

Generalized Ellipsometry Analysis Of Anisotropic Nanoporous Media: Polymer-Infiltrated Nanocolumnar And Inverse-Column Polymeric Films, Dan Liang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Characterization of the structural and optical properties is a subject of significance for nanoporous material research. However, it remains a challenge to find non-destructive methods for investigating the anisotropy of porous thin films with three-dimensional nanostructures. In this thesis, a generalized ellipsometry (GE) analysis approach is employed to study two types of anisotropic nanoporous media: slanted columnar thin films (SCTFs) with polymer infiltration and inverse-SCTF polymeric films. The thesis presents the physical properties obtained from GE analysis, including porosity, columnar shape, principal optical constants, birefringence, etc.

The thesis reports on using a GE analysis approach, combining the homogeneous biaxial layer …

Organometallic Carboxylate Resists For Euv With High Sensitivity, James Passarelli

Nanoscale Science & Engineering (discontinued with class year 2014)

We have developed organometallic carboxylate compounds [RnM(O2CR’)2] capable of acting as negative-tone EUV resists. Overall, the best and fastest resists contain antimony, are pentavalent and the carboxylate group contains a polymerizable olefin (e.g. acrylate, methacrylate or styrenecarboxylate). Evidence suggests that high sensitivity is achieved through the polymerization of olefins in the exposed region. We have performed a systematic sensitivity study of molecules of the type RnM(O2CR’)2 where we have studied seven R groups, four main group metals (M), and three polymerizable carboxylate groups (O2CR’). We found that the greatest predictor of sensitivity of the RnSb(O2CR’)2 resists is their level of …

Inertial Force-Driven Synthesis Of Near-Infrared Plasmonic Nanosphere Composites: Physicochemical Characterizations, Joseph Noel Batta-Mpouma

Graduate Theses and Dissertations

Near-infrared (NIR) responsive nanoparticles (NPs) like gold nanorods (GNRs) are important in biomedical fields because of their transparency for biological tissues. Although GNRs are sought after as contrast agents for theranostics in cancer studies, capping ligands like cetyltrimethylammonium bromide (CTAB) for the GNR synthesis are toxic for biological tissues. The need for an alternative to toxic GNRs is of interest to alleviate the problem.

This work aimed to optimize the synthesis of NIR responsive nanosphere composites (NSCs) by inertial force (g-force) using colloidal gold NPs as model, elucidate the mechanism for the NSC formation, and study their detailed physicochemical characteristics. …

Use Of Precisely Sculptured Thin Film (Stf) Substrates With Generalized Ellipsometry To Determine Spatial Distribution Of Adsorbed Fibronectin To Nanostructured Columnar Topographies And Effect On Cell Adhesion, Tadas Kasputis, Alex Pieper, Keith Brian Rodenhausen, Daniel Schmidt, Derek Sekora, Charles Rice, Eva Schubert, Mathias Schubert, Angela K. Pannier

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Sculptured thin film (STF) substrates consist of nanocolumns with precise orientation, intercolumnar spacing, and optical anisotropy, which can be used as model biomaterial substrates to study the effect of homogenous nanotopographies on the three-dimensional distribution of adsorbed proteins. Generalized ellipsometry was used to discriminate between the distributions of adsorbed FN either on top of or within the intercolumnar void spaces of STFs, afforded by the optical properties of these precisely crafted substrates. Generalized ellipsometry indicated that STFs with vertical nanocolumns enhanced total FN adsorption two-fold relative to flat control substrates and the FN adsorption studies demonstrate different STF characteristics influence …

Large-Scale Graphene Film Deposition For Monolithic Device Fabrication, Khaled Al-Shurman

Graduate Theses and Dissertations

Since 1958, the concept of integrated circuit (IC) has achieved great technological developments and helped in shrinking electronic devices. Nowadays, an IC consists of more than a million of compacted transistors.

The majority of current ICs use silicon as a semiconductor material. According to Moore's law, the number of transistors built-in on a microchip can be double every two years. However, silicon device manufacturing reaches its physical limits. To explain, there is a new trend to shrinking circuitry to seven nanometers where a lot of unknown quantum effects such as tunneling effect can not be controlled. Hence, there is an …

Epitaxial Growth Of Silicon On Poly-Crystalline Si Seed Layer At Low Temperature By Using Hot Wire Chemical Vapor Deposition, Manal Abdullah Aldawsari

Graduate Theses and Dissertations

There has been a growing interest in using low cost material as a substrate for the large grained polycrystalline silicon photovoltaic devices. The main property of those devices is the potential of obtaining high efficiency similar to crystalline Si devices efficiency yet at much lower cost because of the thin film techniques. Epitaxial growth of Si at low temperatures on low cost large grained seed layers, prepared by aluminum induced crystallization method (AIC), using hot wire chemical vapor deposition (HWCVD) system is investigated in this thesis. In this work, different parameters have been studied in order to optimize the growth …

Tio 2 Fibers: Tunable Polymorphic Phase Transformation And Electrochemical Properties, Edna Garcia, Qiang Li, Xing Sun, Karen Lozano, Yuanbing Mao

School of Integrative Biological & Chemical Sciences (Formerly Dept. of Chemistry)

A series of one-dimensional (1D) nanoparticle-assembled TiO2 fibers with tunable polymorphs were prepared via a novel and large scale ForceSpinning® process of titanium tetraisopropoxide (TTIP)/polyvinylpyrrolidone (PVP) precursor fibers followed with a thermal treatment at various calcinations temperatures. The thermal and structural transformations were characterized by thermogravimetric analysis/differential scanning calorimetry, scanning electron microscopy, and X-ray diffraction. The influence of polymorphic phase of the TiO2 fibers on the electrochemical performance in neutral aqueous 1 M Na2SO4 electrolyte was investigated. The polymorphic amorphous/anatase/rutile TiO2 fibers prepared at 450 °C achieved a highest capacitance of 21.2 F g−1 (6.61 mF cm−2) at a current …