Nanoscience and Nanotechnology Commons^™

Electrocatalytic Oxidation Of Methanol At The Nano Ni-B Amorphous Alloy Powdermicroelectrode, Yi-Xiong Zheng, Shi-Bing Yao, Shao-Min Zhou

Journal of Electrochemistry

Electrocatalytic oxidation of methanol at the nano Ni-B amorphous alloy powder-microelectrode in alkaline media was studied by using cyclic voltammetry.Compared to the highly preferred orientation(220) nickel electrode,The onset potential of methanol electrooxidation at the nano Ni-B microelectrode is negatively shifted about 0.04V,and the current density is increased approximately by 2 orders of magnitude.Thus,the nano Ni-B microelectrode has very strong electrocatalytic activity for the oxidation of methanol.The kinetic parameters were determined with the steady polarization curves.The results show that the rate constants for both the oxidation of Ni(Ⅱ) to Ni(Ⅲ) and the reduction of Ni(Ⅲ) to Ni(Ⅱ) at the nano Ni-B …

The Syntheses And Electrochemical Performance Of Nano-Mno2 For Supercapacitor, Jun Ma, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Nano-manganese dioxide were prepared by two different methods which are low temperature solid reaction and chemical deposition.The products were characterized by XRD,SEM,BET and constant current charge-discharge tests.The result shows that there is a close relationship between specific capacitance and BET surface areas.Meanwhile the specific capacitance was impacted little by the structure of the nano-manganese dioxides.However,the product performance of high rates,was influenced by structure,the higher rate can be obtained with the more perfect crystal structure.

Catalysis Of Nano Tio2 For Horseradish Peroxidase, Ya-Qi Zhu, Hai Wu, Hiu Liu, Jie Ma

Journal of Electrochemistry

Horseradish peroxidase immobilized on the surface of titanium dioxide nanoparticles and nanotube modified glassy carbon electrode.The HRP direct electron transfer reaction was compared between TiO₂ nanoparticles and nanotube GC electrode.The results demonstrated that the HRP on TiO₂ nanotube /GC electrode could catalyze electron exchange reaction between electroactivity center of HRP and electrode.And the research of antibody labeled HRP provides a selected signal for antibody-antigen immunoassay.

Determination Of Ddopamine And Ascorbate On Gold Nanoparticle And 4,4-Bis (Methanethiol) Biphenyl (Mtp) Self-Assembled Monolayer Modified Gold Electrode, Hai-Yan Wang, Peng Liu, Ye Wang, Bao-Kang Jin

Journal of Electrochemistry

A new approach to construct an ampermetric biosensor was described.The 4,4-bis(methanethiol)biphenyl(MTP)is adsorbed on to a bare gold electrode to make self-assembled monolayers(MTP/Au SAMs).Then electrodeposited 2mg/mL HAuCl₄ at-200 mV,NG/MTP/Au electrode was prepared.When a differential pulse voltammetric(DPV)technique was used,the peak separation between DA and AA is 155 mV.Hence,the selective determination of dopamine(DA)and ascorbate(AA)in the binary mixture system can be performed.Under the chosen conditions,the peak currents are correspondent linearly to the concentrations of DA and AA in the range of 5.0×10^-7~1×10^-4 mol·L^-1 and 3.5×10^-6~1.0×10^-3mol·L^-1,respectively.The correlation coefficients were 0.998.The detection limit were 1.5×10 …

Template Synthesis And Electrochemical Studies Of Ag(Core)Au(Shell) Nanowires, Li Ling, Ya-Xian Yuan, Min-Min Xu, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

Agcore Aushell nanowires with different thicknesses were prepared by combining template synthesis and chemical reduction method,and characterized by SEM and cyclic voltammetry(CV).The CV results revealed that the AgcoreAushell nanowires with pinhole were transferred to pinhole free structure after several potential scans.By using thiophenol(TP)and p-aminothiophenol(PATP)as probe,the surface enhanced Raman scattering(SERS)effect was investigated on the core-shell nanowires.The results indicated that AgcoreAushell nanowires could be served as a potential SERS substrate,and the difference in the spectral feature of PATP adsorbed onto Au and Ag nanowires enable us to diagnose the pinhole effect of core-shell nanowires by SERS.

Study On The Electrogeneration And Properties Of Superoxide Ion In Aprotic Media By Using Carbon Nanotubes Powder Microelectrode, Ying-Liang Wei, Chen Shao, Hui Feng

Journal of Electrochemistry

Multi-wall carbon nanotubes are filled in the cavity at the tip of a microelectrode to form a carbon nanotubes powder microelectrode(CNTs-PME).The CNTs-PME is used to study the electrochemical reduction of oxygen in aprotic media.It is a nearly reversible redox process of the O₂/O₂^- couple at the CNTs-PME in the dimethyl sulfoxide(DMSO)solution.The heterogeneous electron transfer rate constant(ks)can be measured by steady-state voltammogram and the result is 9.8 10^-3cm /s.As a weak oxidant,the reaction of O₂^- with epinephrine was studied by cyclic voltammetry.Additionally,the reaction of O₂^- with benzoic acid was also discussed …

Preparation And Lithium Storage Performance Of Nano-Structural Sno2/Carbon Nanotubes Composite Electrodes, Hong-Bing Wei, Ling Huang, Xiao-Bin Wu, Fu-Sheng Ke, Jin-Shu Cai, Xiao-Yong Fan, Fang-Zu Yang, Shi-Gang Sun

Journal of Electrochemistry

The Nano-structural SnO₂/Carbon Nanotubes Composites were prepared in a solution of SnCl₂,ethylene glycol(EG),purified MWCNTs and sodium dodecyl sulfate(SDS) at 160 ℃.The phase structure and surface morphology of the composites were measured by XRD HRTEM and SEM.The results indicate that there are high dispersions and high loadings of SnO₂ nanoparticles on MWCNTs.Electrochemical lithium storage performance was studied preliminarily on the obtained samples.MWCNTs modified with SnO₂ nanoparicles were shown to have a higher electrochemical reversible capacity than that of MWCNTs during the charge and discharge process.MWCNTs can accommodate the larger structure strain of the active materials …

Comparison Of The Electrochemical Reactivity Of Electrodes Modified By Carbon Nanotubes With Different Sizes, Guo-Feng Yang, Neng-Qin Jia, Zhi-Yong Wang

Journal of Electrochemistry

The electrochemical activity of multi-walled carbon nanotubes(MWNTs) with different sizes,including four different MWNTs with the same length and different diameter,two different MWNTs with the same diameter and different length has been assessed and compared.The various MWNTs modified electrodes were prepared by immobilizing the suitable amount of MWNTs onto a glassy carbon electrode,and their voltammetric responses to ferricyanide,uric acid and dopamine were examined.The corresponding cyclic voltammetric data was showed that the electrochemical and electrocatalytic activities are depended on the nanotube length.The electrochemical reactivity of short MWNT(S-MWNT) is better than that of long MWNT(L-MWNT),which may be mainly attributed to the existence of …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead-bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive to …

A Simple Sol-Gel Processing For The Development Of High-Temperature Stable Photoactive Anatase Titania, Suresh Pillai, Declan Mccormack, John Colreavy

Articles

No abstract provided.

Novel Electrochemical Method For Synthesis Of Nanostructured Materials Of Noble Metals Based On Poly(N-Vinylpyrrolidone) (Pvp), Wei Pan, Xiao-Kai Zhang, Ming-Hu Huang, Shao-Xin Huang, Xing-Li Feng, Hou-Yi Ma

Journal of Electrochemistry

Gold nanocrystals with controllable size were synthesized through a simple electroreduction method using poly(N-vinylpyrrolidone)(PVP) of different polymerization degree as both stabilizer and shape-controller for gold nanoclusters.Individual gold nanoparticles spontaneously assembled into the wire-and ring-shaped nanoparticle aggregates depending on the PVP's dynamic stretching and curling,and precursor nanoparticles grew into flat,single-crystalline nanoprisms with thickness of dozens of nanometers based on the oriented aggregation between particles.Besides,core-shell Au/Ag nanoparticles were conveniently synthesized through two-step electroreduction of noble metal ions in the presence of PVPK30.The electrochemical synthetic method based on PVP provides a new path for preparation of noble metal nanostructured materials with different shape …

Electrochemical Properties Of The Modified Carbon Nanotubes, Chun-An Ma

Journal of Electrochemistry

Powder micro-electrodes were prepared from raw carbon nanotubes and carbon nanotubes modified by carboxyl.The electro-reduction properties of both the raw and open-ended carbon nanotubes in p-Nitrophenol solution were investigated.The FTIR spectrum result indicated that the functional groups are successfully fixed on the surface of the carbon nanotubes after nitric acid treatment.The cyclic voltammetry results show that the electrochemical activity of carboxyl-modified carbon nanotubes was improved.The mechanism of electro-(reduction) for the carbon nanotubes after acid treatment was discussed.

Immobilization Of Cytochrome C On The Surface Of Single-Wall Carbon Nanotube And Its Direct Electron Transfer And Electrocatalysis, Ya-Jing Yin, Ya-Fen Lv, Ping Wu, Pan Du, Yan-Mao Shi, Chen-Xin Cai

Journal of Electrochemistry

Cytochrome c(Cyto c) was immobilized on the surface of the single-wall carbon nanotube(SWNT) by using the method of adsorption.Infrared spectroscopy indicated that the Cyto c remained in its original structure and did not undergo structural change after its immobilization on the SWNT.The direct electrochemistry of cyto c,which was adsorbed on the surface of the SWNT,was studied by cyclic voltammetry.The voltammetric results demonstrated that the SWNT had promoting effects on the direct electron transfer of Cyto c and also indicated that the immobilized Cyto c retained its bioelectrocatalytic activity to the reduction of H₂O₂.This modified electrode might …

Pre-Oxidative Amperometric Glucose Biosensor Incorporated With Carbon Nanotube And Pbo2, Hong-Lan Qi, Cheng-Xiao Zhang

Journal of Electrochemistry

A pre-oxidative amperometric glucose biosensor incorporated with carbon nanotube,ferrocenemonocarboxylic acid and PbO₂ was designed.The interferences coming from reduced substances,such as ascoribic acid and urine acid were eliminated by PbO₂.The oxidative current is linear at the potential of +0.40 V(vs.SCE) to the concentration of glucose in the range from 0.50 to 20 mmol·L^-1,and the detection limit of glucose is 0.1 mol L^-1.The relative standard deviation is 3.3% for seven successive assays at 5.0 mmol·L^-1glucose.This biosensors have been applied to determination of the glucose in serum with satisfying results.

Investigation On The Resistance To Electrochemical Oxidation Of Carbon Nanotubes With Various Diameters, Yu-Yan Shao, Ge-Ping Yin, Yun-Zhi Gao, Peng-Fei Shi

Journal of Electrochemistry

The resistance to electrochemical oxidation of multi-wall carbon nanotubes(CNT) with various diameters is investigated by applying a fixed potential of 1.2 V(RHE) for 120 h in 0.5 mol L^-1 H₂SO₄.The oxidation current of CNTs decreases with their diameters,but CNTs between 10~20 nm in diameter(D1020) shows the lowest oxidation current.XPS analysis shows that,after oxidation,the increase in surface oxygen for D1020 is the smallest,implying that the oxidation degree for D1020 is the lowest.The conclusion can be reached that CNTs between 10~20 nm in diameter are the most resistant to electrochemical oxidation.The difference in electrochemical stability of CNTs …

Electrodeposition Of Nano-Sb-Zn Alloy In Acetamide-Urea-Nabr-Kbr Melt, Peng Liu, Xin-Ai Guo, Ye-Xiang Tong, Qi-Qin Yang

Journal of Electrochemistry

The electroreduction of Zn(II) and Sb(III) in acetamide-urea-NaBr-KBr(343 K) were studied by cyclic volatmmetry.The reduction of Zn(II) or Sb(III) to the metals is an irreversible process.The transfer coefficient of Zn(II)+2e→Zn and Sb(III) +3e→Sb were calculated to be 0.231 and 0.319,the diffusion coefficient of Zn(II) and Sb(III) in the melt were determined as 1.70*10^-6 and 3.21*10^-6 cm²· s^-1 respectively.The Zn-Sb films with different Zn content from 29.67 at% to 97.34 at% were electrodeposited in acetamide-urea-NaBr-KBr melt at 343 K by controlling the deposition potential and the Zn(II)/Sb(III) molar ratio.The morphology of Zn-Sb film was observed by …

Electrochemical Studies On Electrocatalytic Activity Of AuCore PtShell Nanoparticles To Methanol Oxidation, Fang Bao, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

Au_corePt_shell nanoparticles with different thicknesses were prepared by using chemical reduction method,and characterized by ultraviolet-visible spectroscopy(UV-Vis),transmission electron microscopy(TEM) and cyclic voltammetry(CV).The electrocatalytic activity of Au_corePt_shell nanoparticles with the mean diameter of 70~80 nm to methanol oxidation was investigated by cyclic voltammetry in the acid solution.The results revealed that the prepared core-shell nanoparticles were covered by Pt shell and exhibited the similar optical property and electrocatalytic activity with the normal Pt surface.Moreover,the electrocatalytic activity increased with the electrochemical sweep in the certain potential range.It might be contributed by the special loose structure of Pt shell …

Desulfovibrio Desulfuricans G20 Tetraheme Cytochrome Structure At 1.5 A˚ And Cytochrome Interaction With Metal Complexes, Mrunalini Pattarkine, J J. Tanner, C A. Bottoms, Y H. Lee, Judy D. Wall

Faculty Works

The structure of the type I tetraheme cytochrome c3 from Desulfovibrio desulfuricans G20 was determined to 1.5 A˚ by X-ray crystallography. In addition to the oxidized form, the structure of the molybdate-bound form of the protein was determined from oxidized crystals soaked in sodium molybdate. Only small structural shifts were obtained with metal binding, consistent with the remarkable structural stability of this protein. In vitro experiments with pure cytochrome showed that molybdate could oxidize the reduced cytochrome, although not as rapidly as U(VI) present as uranyl acetate. Alterations in the overall conformation and thermostability of the metal-oxidized protein were investigated …

Electroless Nickel Plating On Carbon Nanotube With Non-Palladium Activation Procedure, Guang-Hui Hu, Hui-Huang Wu, Fang-Zu Yang

Journal of Electrochemistry

A new procedure of surface activation without using palladium salt was proposed for electroless nickel plating on carbon nanotubes.In the procedure,carbon nanotubes were oxidized by nitric acid and then neutralized with NaOH to create carboxyl surface groups which were used to adsorb Ni²⁺ ions,thereafter the adsorbed Ni²⁺ ions were chemically reduced into Ni nano-particles as a catalytic center for electroless nickel deposition,all these were further confirmed by infrared absorption spectra and electron microscopic observations.The results indicate that the procedure is feasible to electroless nickel plating on carbon nanotubes.The different morphology of deposits obtained from electroless plating was also …

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen, Xiao-Lan Wei, Pei Kang Shen

Journal of Electrochemistry

Nano Pt/C electrocatalysts were prepared by intermittent microwave heating method.The electrooxidation of glucose on smooth Pt and～Pt/C electrodes has been studied and compared.The results showed that the electrochemical properties on nano Pt/C were improved due to the reduction of the overpotential and the increase in the kinetic rate.The surface area would be significantly increased when the particle size of the catalyst was reduced to nano-scale,resulting in the increase in the activity.The enhancement in the resistance to poisoning could be explained that the oxygen-containing species are easier to react with poisoning species on nano Pt/C and re-active the electrode.

Special Photoelectrochemical Response Of Nano-Crystalline Tio2 Electrode, Bi-Bo Lan, Jian-Zhang Zhou, Yan-Yan Xi, Hong-Xiang Chen, Guang-Hua Yao, Zhong-Hua Lin

Journal of Electrochemistry

The nano-crystalline TiO₂ electrodes were prepared by spread method,electrodeposition and sol-gel method.The experimental results show that the nano-crystalline TiO₂ electrodes have special photoelectrochemical response-the photocrrent-potential curves appear peaks.The special photoelectrochemical behaviors of nano-(crystalline) TiO₂  electrodes are ascribed to nano-structure as well as special light induced redox reaction mechanism of nano-crystalline semiconductor electrodes.

Corrosion Barrier Development For Lbe Corrosion Resistance: Quarterly Report (April 2006), Biswajit Das

Transmutation Sciences Materials (TRP)

As reported in the last quarterly report, synthesis of Cr nanowires was found to be problematic in terms of uniform coverage. Hence Ni was identified as the alternative metal to form the nanowires. The purpose of the metal nanowires is to provide structural integrity to the nanoporous alumina, as well as a second defense mechanism against corrosion by oxidizing in case the top alumina layer is compromised. Nickel was selected due to its established electrochemical synthesis procedure. While Ni can provide very good structural integrity to the porous alumina, one potential problem is its higher dissolution rate in LBE. However, …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive …

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li, Duo-Chang Cai, Xiao-Ying He

Journal of Electrochemistry

The electrochemical behavior of 3,4-Dihydroxybenzoic acid(DHBA) on modified multiply wall carbon nanotubes electrode was investigated by cyclic voltammetry(CV) and square wave voltammetry(SWV). Results show that in 0.1 mol/L HCl solutions the modified carbon nanotube electrode has an obvious electrocatalytic effect on the oxidation and deoxidization of DHBA. The oxidation current of DHBA is linear to it's concentration in the range of 4.0×10^-6～1.0×10^-4 mol/L and 2.0×10^-4～8.0×10^-4 1mol/L with correlation coefficient of 0.9995 and 0.9992. The detection limit is 1.0×10^-6 mol/L.

Surface And Sructure Investigations Of Membrane Electrode Assembly In Dmfc Lifetime Testing, Xuan Cheng, Cheng Peng, Meng-Di You, Jing Liu, Ying Zhang

Journal of Electrochemistry

The lifetime and performance of a direct methanol fuel cell (DMFC) were investigatedto understand the correlation between thestructure of catalysts/membrane and cell performanceversus time. The cell polarization and performance curves were obtained during the DMFC operation with the time. The catalysts and Nafion membrane of the membrane electrode assembly (MEA) from the lifetime test were comprehensively examined by XRD, HRTEM, FTIR and Raman spectroscope techniques. The results revealed that there was significant performance degradation during the first 200 hours operation; while the degradation was slowing down between 200 and 704 hours operation. The degradation became worse after 1002 h operation. …

The Research Of Nano-Sized Nio Anode Materials For Lithium Ion Batteries, Jun-Mei Yan, Jing Zhang, Yong Yang

Journal of Electrochemistry

The nano-sized NiO materials were synthesized by solid phase method and sol-gel method. The synthesis conditions were optimized by DSC and TG techniques. The sol-gel method was optimized by changing the solvent and regulating the solution's pH for preparing NiO material. The structure and morphology of the materials were also characterized by means of XRD and TEM techniques, and the electrochemical performances of the materials were studied by the galvanostatically charge and discharge experiments.

Surface-Enhanced Raman Spectra Of Cytosine Adsorbed On A Roughened Gold Electrode, Yuan-Fei Wu, Jian-Feng Li, De-Yin Wu, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Cytosine adsorbed on a roughened gold electrode has been investigated by using electrochemical cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS). The results indicate that cytosine was adsorbed on the Au electrode in a perpendicular orientation via the N3 position. As the maximum enhancement of ring breathing mode appears at negative potentials compared with other modes, both the electromagnetic enhancement and the charge transfer mechanism were considered to contribute to the SERS intensity. The binding interaction between cytosine and the gold electrode was weakened when the potential was negatively moved. The result also indicates that the SERS technique can be used …

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang, Wei-Min Cao, Li-Yi Shi

Journal of Electrochemistry

The catalytic splitting decomposition of carbon nanotubes isprocessed by dispersing with dilute nitric acid and thermal oxidation. Then well-proportionedphenolic resin is mixed in the carbon nanotubes. Then, the carbon nanotubesare made into electrodes by hot-press molding after the process of milling with high speed. The surface of the carbon nanotubes electrodes is analyzed by SEM. Active red X-3B simulated waster water is disposed by carbon nanotubes catalyticelectrode (anode) and stainless steel(cathode). The influencing factors of degradation by current density, concentrationof electrolyte, systemtemperature and pH are investigated. The experimental results indicated that acidiccondition is propitious tothe degradationreaction of organicdyestuff and wastewater …

The Application Of Astm C1202-93 On Evaluating The Performance Of Anti-Corrosion Of Concrete, Yuan-Chen Yuan, Tsung-Yueh Tu, Chao-Lung Hwang

Journal of Electrochemistry

The test of chloride ion penetration based on the standards of ASTM C1202-93 is applied to evaluate the anti-corrosion performance of concrete in this research. Concrete specimens were produced according to ACI 318-89 mixture proportioning design and the Desenfied Mixture Design Algorithm (DMDA) and were measured the 6-hour coulombs at the age of 91 days. Results show that w/b is not the factor influencing chloride penetration of ACI concrete, as the ion penetration of ACI specimens is all higher than 2 000 Coulombs and can even be poorer than 10 000 Coulombs. With a proper amount of pozzolanic material, the …

Cyclic Voltammetry And Surface Enhanced Raman Spectroscopy Of Dissociative Adsorption Of Ethanol On Pt-Ru Electrodes, Bin Zhang, Hai-Hui Zhou, Zu-Biao Wen, Qi-Ling Zhong, Peng Huang, Xiong-Yuan Yang, Bin Ren, Tian

Journal of Electrochemistry

The behaviors of dissociative adsorption of ethanol on roughened platinum-ruthenium electrode with high activity of SERS were studied by using cyclic voltammetry and in-situ surface enhanced Raman spectroscopy, surface enhanced Raman spectra of dissociative adsorption of ethanol on Pt electrode in acid was obtained for the first time. It is shown that the Pt-Ru could lower the over-potential of CO oxidation when compared to Pt electrode. The results show that the ethanol in acid medium can be self-dissociated at Pt-Ru electrode to produce CO, which discourage the further oxidation of ethanol, some information of Pt-C and Pt-C-Pt stretching vibration from …