Nanoscience and Nanotechnology Commons^™

Development Of Integrated Zinc Oxide Nanorods Coated Glass Substrate Sensing Device, Mohd Yusof Haziezol Helmi

Student Works (2020-2029)

A simple and practical cost-effective integrated zinc oxide (ZnO) nanorods coated glass substrate sensing device for humidity and formaldehyde vapor sensing applications is reported. The developed sensor device is composed of a commercial light-emitting diode (LED) and photodiode that correspondingly served as light source and detector which precisely positioned on a 3D printed sensor platform. A receiver circuit and Arduino platform were employed for signal amplification and processing. A uniform ZnO nanorods coating were grown on the surface of glass substrate via hydrothermal method by controlling the growth durations and coating length. A standard reference for the optimum working condition …

In-Situ Gold-Ceria Nanoparticles: Superior Optical Fluorescence Quenching Sensor For Dissolved Oxygen, Nader Shehata, Ishac Kandas, Effat Samir

Electrical & Computer Engineering Faculty Publications

Cerium oxide (ceria) nanoparticles (NPs) have been proved to be an efficient optical fluorescent material through generating visible emission (~530 nm) under violet excitation. This feature allowed ceria NPs to be used as an optical sensor via the fluorescence quenching Technique. In this paper, the impact of in-situ embedded gold nanoparticles (Au NPs) inside ceria nanoparticles was studied. Then, gold–ceria NPs were used for sensing dissolved oxygen (DO) in aqueous media. It was observed that both fluorescence intensity and lifetime were changed due to increased concentration of DO. Added gold was found to enhance the sensitivity of ceria to DO …

Improved Contacts And Device Performance In Mos2 Transistors Using 2d Semiconductor Interlayers, Kraig Andrews

Wayne State University Dissertations

The rapid growth of modern electronics industry over the past half-century has been sustained by the continued miniaturization of silicon-based electronics. However, as fundamental limits approach, there is a need to search for viable alternative materials for next-generation electronics in the post-silicon era. Two-dimensional (2D) semiconductors such as transition metal dichalcogenides (TMDs) have attracted much attention due to their atomic thickness, absence of dangling bonds and moderately high carrier mobility. However, achieving low-resistance contacts has been major impediment in developing high-performance field-effect transistors (FETs) based on 2D semiconductors. A substantial Schottky barrier (SB) is often present at the metal/2D-semicondcutor interface, …

Surface And Structure Engineering For Next Generation Lithium Metal Batteries, Ke Chen

Electronic Theses and Dissertations

Lithium (Li) metal has been considered as one of the most promising anode materials to replace conventional graphite for Li-ion battery due to its high theoretical capacity (3860 mAh g-1) and low electrochemical potential (-3.04 V vs standard hydrogen electrode). However, it still faces some problems such as unstable solid electrolyte interphase (SEI), uncontrolled Li dendrites growth, and infinite volume change during battery charging/discharging. To develop a stable and low-cost Li metal anode for next-generation Li metal battery, in this dissertation, we have made efforts to understand and solve these problems in two aspects, by introducing an artificial SEI and …

Fabrication, Development, And Characterization Of Hipco Swcnt - Alginate Hydrogel Composites For Cellular Product Applications, Fabian Armando Alvarez-Primo

Open Access Theses & Dissertations

In this study, we designed, synthesized, and characterized ultrahigh purity single-walled carbon nanotube (SWCNT)-alginate hydrogel composites. Among the parameters of importance in the formation of an alginate-based hydrogel composite with single-walled carbon nanotubes, are their varying degrees of purity, their particulate agglomeration and their dose-dependent correlation to cell viability, all of which have an impact on the resultant compositeâ??s efficiency and effectiveness towards biomedical applications. To promote their homogenous dispersion by preventing agglomeration of the SWCNT, at first, we used three different surfactants-sodium dodecyl sulfate (SDS-anionic), cetyltrimethylammonium bromide (CTAB-cationic), and Pluronic F108 (nonionic). After experimentation and corroboration through evidence obtained …

Electric Field Control Of Fixed Magnetic Skyrmions For Energy Efficient Nanomagnetic Memory, Dhritiman Bhattacharya

Theses and Dissertations

To meet the ever-growing demand of faster and smaller computers, increasing number of transistors are needed in the same chip area. Unfortunately, Silicon based transistors have almost reached their miniaturization limits mainly due to excessive heat generation. Nanomagnetic devices are one of the most promising alternatives of CMOS. In nanomagnetic devices, electron spin, instead of charge, is the information carrier. Hence, these devices are non-volatile: information can be stored in these devices without needing any external power which could enable computing architectures beyond traditional von-Neumann computing. Additionally, these devices are also expected to be more energy efficient than CMOS devices …

Transient Electrochemical Surface-Enhanced Raman Spectroscopic Study In Electrochemical Reduction Of P-Nitrothiophenol, Yun Ling, Jing Tang, Guo-Kun Liu, Cheng Zong

Journal of Electrochemistry

P-nitrothiophenol (PNTP) is one of the most common probe molecules studied by surface-enhanced Raman spectroscopy (SERS). The research in electrochemical reduction behavior of PNTP will help understanding the mechanism for the nitrobenzene reduction. In this paper, we used transient electrochemical surface-enhanced Raman spectroscopy (TEC-SERS) to study the SERS of PNTP with cyclic voltammetry and chronoamperometry on gold electrodes. The results show that the TEC-SERS provide a time resolution that equals the transient electrochemical methods, and we concluded that the reaction was so quick that we did not observe the spectral information of intermediate species described in the literatures with a …

Electrochemical Sensor Based On Magnetic Electrode Modified With Magnetic Molecularly Imprinted Nanoparticles Immobilized Hemoglobin For Determination Of Hydrogen Peroxide, Yang Yuan, Jia-Xin Wang, Yu-Hua Cao

Journal of Electrochemistry

In this work, the surface-imprinted technique was used to prepare magnetic hemoglobin (Hb) imprinted nanoparticles, using Fe₃O₄@SiO₂ NPs as the carrier, Hb as the template molecule, and tetraethyl orthosilicate (TEOS) as the imprinted polymer monomer. The nanoparticles had a core-shell structure, with magnetic Fe₃O₄ NPs as the core and Hb imprinted polymers as the shell. Therefore, Hb could be concentrated and fixed on the surface of the magnetic imprinted nanoparticles (MMIPs NPs). Furthermore, MMIPs NPs were immobilized with chitosan (CS) on the surface of a magnetic electrode to constitute Hb enzyme-like biosensor …

Synthesis Of Cellulose Nanocrystal-Gold Nanoparticle Hybrid System For Surface Plasmon-Enhanced Property, Mahshid Iraniparast

Graduate Theses and Dissertations

Gold nanoparticles (AuNPs) have been brought to the forefront of various applications, ranging from theranostics, to organic photovoltaics, to biosensing owing to their localized surface plasmon resonance (LSPR) property. However, this property needs to be improved in order to allow for high sensitivity and quantitative detection of biomolecules. Hybrids of AuNPs with low-dielectric cellulose nanocrystal (CNCs) would yield enhancement of the LSPR property, which is driven by the confinement of electron oscillation at their interfaces. This study proposed a seed-mediated growth method to synthesize hybrids of CNCs-AuNPs. Sulfate groups on the surface of CNCs served as the sites for the …

Gamma-Ray Radiation Effects In Graphene-Based Transistors With H-Bn Nanometer Film Substrates, E. J. Cazalas, Michael R. Hogsed, S. R. Vangala, Michael R. Snure, John W. Mcclory

Faculty Publications

Radiation effects on graphene field effect transistors (GFETs) with hexagonal boron nitride (h-BN) thin film substrates are investigated using 60Co gamma-ray radiation. This study examines the radiation response using many samples with varying h-BN film thicknesses (1.6 and 20 nm thickness) and graphene channel lengths (5 and 10 μm). These samples were exposed to a total ionizing dose of approximately 1 Mrad(Si). I-V measurements were taken at fixed time intervals between irradiations and postirradiation. Dirac point voltage and current are extracted from the I-V measurements, as well as mobility, Dirac voltage hysteresis, and the total number of GFETs that remain …

Optical Angular Scatterometry: In-Line Approach For Roll-2-Roll And Nano-Imprint Fabrication Systems, Juan Jose Faria-Briceno

Electrical and Computer Engineering ETDs

As critical dimensions continue to shrink and structures become more complex, metrology processes are challenging to implement during in-line nanomanufacturing. Non-destructive, non-contact, and high-speed conditions are required to achieve proper metrology processes during in-line manufacturing. Optical scatterometry is a nanoscale metrology tool widely used in integrated circuit manufacturing for characterization and quality control. However, most applications of optical scatterometry operate off-line. A high-speed, in-line, non-contact, non-destructive scatterometry angular system has been demonstrated in this work to scan pattern surfaces during real-time nano-fabrication.

Our system has demonstrated scanning capabilities using flat, 1D and 2D complex structures. The flat surface samples consist …

Preparation Of Nanostructural Mno-Porous Graphene Hybrid Material By Thermally-Driven Etching Of Mno For Lithium-Air Batteries, Juan Yang, Jun-Wei Lang, Peng Zhang, Bao Liu

Journal of Electrochemistry

In this paper, improving the surface morphology of graphene(GNSs) as designed concept. we describe a MnO/porous-graphene(MnO-PGNSs) was synthesized by a simple site-localized Mn²⁺ on GO (Mn-GO) by charge adsorption and then driving by high-temperature calcination, growing MnO nanoparticles and etching GNSs achieved on step. And Then focus on the key factors of influenced the etch hole formation are analyzed, founded the dispersion of Mn-GO; layer number of GO and calcination temperature also affected the formation of holes. In addition, the MnO-PGNSs as lithium-air battery cathode exhibits high reversible capacity compared with GNSs and PGNs and it is able to …

A Facile Route To Synthesize Pt-Wo3 Nanosheets With Enhanced Electrochemical Performance For Her, Peng-Jie Jiang, Yi Lv, Chang-Miao Chen, Hong-Cheng He, Yong Cai, Ming Zhang

Journal of Electrochemistry

Platinum-tungsten trioxide (Pt-WO₃) nanosheets were synthesized on nickel foams (NFs) directly. As great conductive networks, NFs substrates could greatly improve the electrode performance of WO₃. The modified platinum nanoparticles not only enhanced the electron transformation of catalysts, but also increased the active sites for hydrogen evolution reaction (HER). Pt-WO₃/NF revealed a better catalytic activity than WO₃/NFs with a smaller Tafel slope (80 mV·dec^-1) and a lower overpotential of 72 mV at the current density of 10 mA·cm^-2. In addition, Pt-WO₃/NF showed great durability and stability during …

Pd Nanoparticles Supported On The Etched Ni Foams As High-Performance Electrocatalysts For Direct Ethanol Fuel Cells, Chi Zhang, Cheng-Fei Li, Gao-Ren Li

Journal of Electrochemistry

The development of non-Pt anode electrocatalysts with high activity and long-term durability at low cost for fuel cells still remains enormous challenge. Here we report the Pd nanoparticles supported on Ni foams etched by the mixed acids (HNO₃+H₂SO₄+H₃PO₄+CH₃COOH) (Pd/ME-NF) that are designed and fabricated as high-performance electrocatalysts for ethanol oxidation in alkaline media. Because of the advantages of large open space, fast electrolyte penetration/diffusion and rapid electron transfer process, the Pd/ME-NF catalysts exhibited significantly improved electrocatalytic activity and durability compared with the commercial Pd/C catalysts.

A Multicarrier Technique For Monte Carlo Simulation Of Electrothermal Transport In Nanoelectronics, Tyler J. Spence

Doctoral Dissertations

The field of microelectronics plays an important role in many areas of engineering and science, being ubiquitous in aerospace, industrial manufacturing, biotechnology, and many other fields. Today, many micro- and nanoscale electronic devices are integrated into one package. e capacity to simulate new devices accurately is critical to the engineering design process, as device engineers use simulations to predict performance characteristics and identify potential issues before fabrication. A problem of particular interest is the simulation of devices which exhibit exotic behaviors due to non-equilibrium thermodynamics and thermal effects such as self-heating. Frequently, it is desirable to predict the level of …

Laser-Spark Multicharged Ion Implantation System ‒ Application In Ion Implantation And Neural Deposition Of Carbon In Nickel (111), Oguzhan Balki

Electrical & Computer Engineering Theses & Dissertations

Carbon ions generated by ablation of a carbon target using an Nd:YAG laser pulse (wavelength λ = 1064 nm, pulse width τ = 7 ns, and laser fluence of 10-110 J/cm²) are characterized. Time-of-flight analyzer, a three-mesh retarding field analyzer, and an electrostatic ion energy analyzer are used to study the charge and energy of carbon ions generated by laser ablation. The dependencies of the ion signal on the laser fluence, laser focal point position relative to target surface, and the acceleration voltage are described. Up to C⁴⁺ are observed. When no acceleration voltage is applied between …

Enhanced Crystallinity Of Triple-Cation Perovskite Film Via Doping Nh4Scn, Ziji Liu, Detao Liu, Hao Chen, Long Ji, Hualin Zheng, Yiding Gu, Feng Wang, Zhi Chen, Shibin Li

Electrical and Computer Engineering Faculty Publications

The trap-state density in perovskite films largely determines the photovoltaic performance of perovskite solar cells (PSCs). Increasing the crystal grain size in perovskite films is an effective method to reduce the trap-state density. Here, we have added NH₄SCN into perovskite precursor solution to obtain perovskite films with an increased crystal grain size. The perovskite with increased crystal grain size shows a much lower trap-state density compared with reference perovskite films, resulting in an improved photovoltaic performance in PSCs. The champion photovoltaic device has achieved a power conversion efficiency of 19.36%. The proposed method may also impact other optoelectronic …

Regulation Of Copper Surface Via Redox Reactions For Enhancing Carbon Dioxide Electroreduction, Bao-Hua Hang, Jin-Tao Zhang

Journal of Electrochemistry

A large-scale application of fossil fuels has led to excessive emission of carbon dioxide (CO₂), resulting in serious environmental issues. A promising path to reducing CO₂ emissions is recycling CO₂ into valuable chemicals and fuels through an electrochemical process. Herein, the redox reactions between copper (Cu) and ferric chloride (FeCl₃) have been utilized to regulate the Cu surface composition and structure, aimed to improve the electrocatalytic activity toward CO₂ reduction. Typically, a series of samples (named Cu-1h, Cu-2h, Cu-3h and Cu-4h) were prepared via the redox reactions for various time from 1 to …

Effect Of Morphology Of Fe-N Codoped Carbon Nanomaterial On Electrochemical Reduction Reactions, Er-Ling Li, Fa Yang, Ming-Bo Ruan, Ping Song, Wei-Lin Xu

Journal of Electrochemistry

Graphene nanosheets (GS) and carbon nanotubes have been considered as good catalysts candidates for applications in energy conversion and storage. However, hybrids of GS and carbon nanotubes are always formed in transition metal-based nitrogen-doped system, making the system quite complex for exploring the structure-activity relationship. To prepare the catalysts with desired species controllably, we try to adjust the outcomes with the effect of nitrogen on the growth of carbon nanotubes. In this work, a series of Fe-N co-doped carbon hybrid catalysts containing N-doped GS or hybrids of GS/bamboo carbon nanotubes (BCNTs) or BCNTs were obtained with one-step pyrolyzed method. To …

Electrocatalytic Nanomaterials For Reduction Of Hydrogen Peroxide As Potential Radioprotectors, Rui-Hong Jia, Jin-Xuan Zhang, Xiao-Dong Zhang, Mei-Xian Li

Journal of Electrochemistry

Nanomaterials have shown many potential application prospects in the biomedical field, such as medical imaging, drug delivery and biosensing due to their unique physical and chemical properties. In this review we focus on nanomaterials that have shown not only abilities of radiation protection, but also good electrocatalytic activities toward reduction reactions of hydrogen peroxide and oxygen. We discuss the abilities of radiation protection of these nanomaterials that are ascribed to their enzyme-like activities because their catalytic properties provide an effective pathway for scavenging free radicals in vivo via rapid reactions with reactive oxygen species. We also provide insights into electrocatalytic …

Surface Engineering Solutions For Immersion Phase Change Cooling Of Electronics, Brendon M. Doran

Master's Theses

Micro- and nano-scale surface modifications have been a subject of great interest for enhancing the pool boiling heat transfer performance of immersion cooling systems due to their ability to augment surface area, improve wickability, and increase nucleation site density. However, many of the surface modification technologies that have been previously demonstrated show a lack of evidence concerning scalability for use at an industrial level. In this work, the pool boiling heat transfer performance of nanoporous anodic aluminum oxide (AAO) films, copper oxide (CuO) nanostructure coatings, and 1D roll-molded microfin arrays has been studied. Each of these technologies possess scalability in …

Plasmonic Properties Of Nanoparticle And Two Dimensional Material Integrated Structure, Desalegn Tadesse Debu

Graduate Theses and Dissertations

Recently, various groups have demonstrated nano-scale engineering of nanostructures for optical to infrared wavelength plasmonic applications. Most fabrication technique processes, especially those using noble metals, requires an adhesion layer. Previously proposed theoretical work to support experimental measurement often neglect the effect of the adhesion layers. The first finding of this work focuses on the impact of the adhesion layer on nanoparticle plasmonic properties. Gold nanodisks with a titanium adhesion layer are investigated by calculating the scattering, absorption, and extinction cross-section with numerical simulations using a finite difference time domain (FDTD) method. I demonstrate that a gold nanodisk with an adhesive …

Experimental And Computational Study On Magnetic Nanowires Of Layered Titanates, Caleb Layne Heath

Graduate Theses and Dissertations

The intricate nanostructures of layered titanates are unique among nanomaterials due to their easy and inexpensive syntheses. These nanomaterials have been proven valuable for use in industries as varied as energy, water treatment, and healthcare, and can be produced at industrial scales using already existent equipment. They have complex morphology, and surface structure well suited to chemical modification and doping. However, there is a longstanding debate on their lattice structure after the doping. There is a long-unmet need to understand, using both experimental and simulation methods, how dopants alter the clay-like layered crystal structure and associated physical and chemical properties. …

In Situ/Operando Visualization Of Electrode Processes In Lithium-Sulfur Batteries: A Review, Shuang-Yan Lang, Xin-Cheng Hu, Rui Wen, Li-Jun Wan

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries have been regarded as one of the most promising candidates for the next-generation energy storage devices. Fundamental understanding of the structure and evolution processes at electrode-electrolyte interfaces is essential to the further development. In this review, we summarize recent advances in the interfacial observations by means of various in situ/operando visualization techniques, including scanning probe microscopy (SPM), electron microscopy (EM), X-ray microscopy (XRM) and optical microscopy (OM). The real-time investigation provides important evidence for the morphology and component changes including S/Li₂S transformation, polysulfide dissolution on cathodes and Li/solid electrolyte interphase (SEI) evolution on anodes, which …

Recent Developments In Surface/Interface Modulation And Structure-Performance Relationship Of Cathode Catalysts For Li-Air Batteries, Rui Gao, Jun-Kai Wang, Zhong-Bo Hu, Xiang-Feng Liu

Journal of Electrochemistry

Lithium-air battery has been considered to be one of the most promising secondary battery systems because of its high energy density. However, the sluggish kinetics of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) on the cathode, and the high overpotential, poor cycle stability and low rate capacity have severely blocked the development and application of Li-air battery. One of the effective strategies to alleviate these issues is to develop cathode catalysts for Li-air batteries. The design and development of bifunctional cathode catalysts with high activity and efficiency on both ORR and OER is highly desired for Li-air …

Femtosecond Photon-Mediated Plasma Enhances Photosynthesis Of Plasmonic Nanostructures And Their Sers Applications, Peng Ran, Lan Jiang, Xin Li, Bo Li, Pei Zuo, Yongfeng Lu

Department of Electrical and Computer Engineering: Faculty Publications

Laser ablation in liquid has proven to be a universal and green method to synthesize nanocrystals and fabricate functional nanostructures. This study demonstrates the superiority of femtosecond laser-mediated plasma in enhancing photoredox of metal cations for controllable fabrication of plasmonic nanostructures in liquid. Through employing upstream high energetic plasma during laser-induced microexplosions, single/three-electron photoreduction of metallic cations can readily occur without chemical reductants or capping agents. Experimental evidences demonstrate that this process exhibits higher photon utilization efficiency in yield of colloidal metal nanoparticles than direct irradiation of metallic precursors. Photogenerated hydrated electrons derived from strong ionization of silicon and water …

Fast Growth Of Thin Mapbi3 Crystal Wafers On Aqueous Solution Surface For Efficient Lateral-Structure Perovskite Solar Cells, Ye Liu, Qingfeng Dong, Yanjun Fang, Yuze Lin, Yehao Deng, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Solar-grade single or multiple crystalline wafers are needed in large quantities in the solar cell industry, and are generally formed by a top-down process from crystal ingots, which causes a significant waste of materials and energy during slicing, polishing, and other processing. Here, a bottom-up technique that allows the growth of wafer-size hybrid perovskite multiple crystals directly from aqueous solution is reported. Single-crystalline hybrid perovskite wafers with centimeter size are grown at the top surface of a perovskite precursor solution. As well as saving raw materials, this method provides unprecedented advantages such as easily tunable thickness and rapid growth of …

Development And Demonstration Of A Processing And Assembly Pathway For A 3d-Synchronous Field Programmable Gate Array, Robert Carroll

Legacy Theses & Dissertations (2009 - 2024)

Field Programmable Gate Arrays (FPGA) are integrated circuits which can implement virtually any digital function and can be configured by a designer after manufacturing. This is beneficial when dedicated application specific runs are not time or cost effective; however, this flexibility comes at the cost of a substantially higher interconnect overhead. Three-dimensional (3D) integration can offer significant improvements in the FPGA architecture by stacking multiple device layers and interconnecting them in the third or vertical dimension, through the substrate, where path lengths are greatly reduced. This will allow for a higher density of devices and improvements in power consumption, signal …

Cvd Molybdenum Disulfide : Material And Device Engineering, Eui Sang Song

Legacy Theses & Dissertations (2009 - 2024)

Molybdenum disulfide (MoS2) is a semiconducting 2D layered material that has attracted a lot of attention due to its material properties for electronics and optoelectronics device applications. These include a layer-dependent band gap, an indirect to direct energy transition at monolayer state, and strong light-matter interaction. A large majority of 2D materials and devices have been studied through micromechanical exfoliation for extraction and electron beam lithography for device fabrication. These methodologies while able to generate high quality materials and precisely fabricated devices, are not suitable for large scale production. Efforts have been made to make MoS2 and other 2D materials …

Exploring Gated Nanoelectronic Devices Fabricated From 1d And 2d Materials, Prathamesh A. Dhakras

Legacy Theses & Dissertations (2009 - 2024)

One and two dimensional materials are being extensively researched toward potential application as ultra-thin body channel materials. The difficulty of implementing physical doping methods in these materials has necessitated various alternative doping schemes, the most promising of which is the electrostatic gating technique due to its reconfigurability. This dissertation explores the different fundamental devices that can be fabricated and characterized by taking advantage of the electrostatic gating of individual single-walled carbon nanotubes (SWNTs), dense SWNT networks and exfoliated 2D tungsten diselenide (WSe2) flakes.