Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Keyword
-
- 20 liter (1)
- ASTM E1226 (1)
- Black Powder (1)
- Blast Wave (1)
- Breaching (1)
-
- Charge Geometry (1)
- Coal dust (1)
- Combustible dust (1)
- Concrete (1)
- Confinement (1)
- Defense (1)
- Detonation (1)
- Detonation Wave (1)
- Dust explosion (1)
- Explosives (1)
- Impact (1)
- Mine Seals (1)
- Optical Time of Arrival (1)
- Plate Dent (1)
- Polyurethane (1)
- Projectile (1)
- RDX (1)
- Reaction Zone (1)
- Shock Wave (1)
- SiC (1)
- Siwek 20 liter (1)
- Synthesis (1)
- TNT (1)
- X-Ray Diffraction (1)
- Publication
Articles 1 - 5 of 5
Full-Text Articles in Explosives Engineering
Investigation Of Anomalous Data Trends During Coal Dust Explosibilty Testing, Jacob Lee Miller
Investigation Of Anomalous Data Trends During Coal Dust Explosibilty Testing, Jacob Lee Miller
Doctoral Dissertations
Coal dust explosibility is a health and safety concern that has been a recognized hazard for over 100 years. Initial testing by the Author using a Siwek 20L apparatus recorded a secondary maximum pressure at higher dust concentrations (1,000-7,000g/m3) with Pulverized Pittsburgh Coal (PCC). Higher dust concentrations are beyond the typical ASTM E1226 testing procedure but are possible in mining and processing scenarios. No reference documents have been discovered that show a secondary maximum pressure at higher dust concentrations. Literature reviewed identified that once a coal dust concertation generates a peak pressure, the pressure remains constant or decreases …
The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien
The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien
Masters Theses
"The effects of a rigid polyurethane foam used as a confinement material on four types of breaching explosives were tested, focusing on the changes in shockwave peak pressures, detonation load compression forces, and brisance cratering abilities. The Plate Dent testing procedure was modified to incorporate a load cell force sensor, and two air overpressure sensors were included adjacent to the blast to quantify each test result. The testing variables focused on the polyurethane foam cure times and thickness volumes around the breaching explosives to determine the breaching charges' optimal energy output capabilities when confined by the foam material. The rigid …
Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer
Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer
Doctoral Dissertations
“This research investigates the physical and chemical processes that contribute to the detonation synthesis of silicon carbide nanoparticles. Bulk production of SiC nanoparticles through detonation is possible due to pressures achieved over 20 GPa and temperatures over 2000 K as well as quenching rates in excess of 13 billion K/second. These conditions catalyze reaction and bottom-up molecular growth while retaining particles < 100 nm in diameter. In this work, detonation synthesis of SiC was demonstrated by incorporation of polycarbosilane, an SiC precursor material, into an RDX/TNT explosive matrix prior to detonation. Detonation Synthesis of SiC was also accomplished by reacting elemental silicon with carbon liberated by the detonation of negatively oxygen balanced TNT. Hydrodynamic simulation of a 60:40 mass ratio RDX/TNT detonation created conditions thermodynamically suitable to produce cubic silicon carbide within the first 500 nanoseconds after the passage of the detonation wave while carbon remains chemically reactive for molecular formation. Simulations and experimental tests indicated that loading configuration and impedance mismatch of the precursor additives used in detonation synthesis results in conditions in the additives that exceed the accepted detonation pressure of the explosive by greater than three times. Finally, a full factorial experimental design showed increasing silicon concentration, reducing silicon size, and reducing oxygen balance by adjusting the ratio of RDX to TNT decreased the explosives detonation pressure by 20% and increased the soot yield and concentration of SiC observed in the detonation products by 82% and 442% respectively”--Abstract, page iv.
Investigating The Focusing Effect Of Charge Geometry With Computer Simulations, Witness Plates, And High-Speed Videography, Kelly Ray Williams
Investigating The Focusing Effect Of Charge Geometry With Computer Simulations, Witness Plates, And High-Speed Videography, Kelly Ray Williams
Doctoral Dissertations
"Scaled distance is used to calculate a safe standoff radius from the detonation of a known mass of an explosive. It has been shown that varying only the geometry of the charge significantly overdrives regions of the blast wave potentially resulting in hazardous overpressure levels at scaled distance safe radii. Pressure transducers are used to measure overpressure surrounding spherical, cylindrical, and cubic charges to determine if bridge waves were formed at the edges between flat sides as seen in published studies of cylindrical charges. In the fireball field a witness plate is used to evaluate radial energy distribution with a …
Projectile Generator Design For Underground Coal Mine Seal Testing, Ethan Allan Steward
Projectile Generator Design For Underground Coal Mine Seal Testing, Ethan Allan Steward
Masters Theses
"Underground coal mines have several dangers, one of the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at …