Explosives Engineering Commons^™

Geometric Effects Of Warfighters On Body Armor Fit And Protective Capabilities Against Shock Wave Energy, Melissa Lynn Sutter

Doctoral Dissertations

Body armor is a vital piece of protective equipment for warfighters to defend against threats, necessitating continued development to improve comfort, weight, and protection. However, female warfighters often wear unisex body armor, designed primarily for the male torso. Current research has evaluated the short- and long-term detriments of female warfighters wearing these armors, focusing on comfort and performance. However, these studies do not comprehensively consider how a non-form-fitting armor compromises warfighter safety from battlefield threats. This research examines the geometric effects of female warfighters on armor protection level when defending against shock threats by evaluating the energy distribution on a …

Development Of A Method To Measure Blast Overpressure Exposure Using Orthogonal Sensor Orientations, Nicholas Kuehl

Masters Theses

Measuring and recording blast exposure to military personnel from shoulder-fired weaponry or improvised explosive devices to correlate health outcomes like mild traumatic brain injury has been a goal for many years. As such, many wearable sensors have been developed and tested for accuracy and reliability. Despite this, knowing the sensor orientation in relation to the blast source is important to fully correlate the actual personnel exposure to clinical outcomes. This research investigates whether pressures recorded at three independent orientations in the x, y and z planes can be combined to a representative pressure that is independent of orientation. Important metrics …

Overpressure Waveform Comparison Of High Explosive, Methane, And Coal Dust Explosions, Frank James Schott

Masters Theses

Methane and coal dust explosions remain a leading cause of catastrophic mining accidents, making it critical to understand their overpressure characteristics for better hazard modeling, mitigation, and regulation. Although high explosives (HE), flammable gases, and dusts have been studied separately, direct waveform comparisons in identical environments are rare. This study addresses that gap by comparing overpressure waveforms from HE, methane-air mixtures, and coal dust explosions to assess differences in peak pressure, impulse, rise time, and phase duration. Twenty-seven tests were conducted using standardized instrumentation and sensor arrays. Results showed that HE generated the highest peak pressures with short positive phases …

An Experimental Study Into The Methods Of Water Coupling And Their Impact On Kinetic Energy And Blast Over Pressure Through The Use Of A Ballistic Pendulum, Jeremiah Alan Cohn

Masters Theses

Water coupled charges utilize the material properties of water to alter their behavior for reductions in overpressure and increases in kinetic energy. Although water coupling has been studied directly, combined usage of the two primary methods of water coupling, tamping and pushing, hinders further research. This study addresses the gap in literature by comparing ballistic pendulum and blast data for charges with water tamping and pushing to determine differences in kinetic energy, peak overpressure, impulse, noise and duration of fireball. The results showed that water tamping provided a 69.1% increase in kinetic energy, an 18.6% reduction in incident overpressure, a …

The Dynamic Material Response Of Csa Cement Using A Split Hopkinson Bar, Elliott L. Morgan

Theses and Dissertations--Mining Engineering

The University of Kentucky Center for Applied Energy Research (CAER) Cementitious Materials Group is developing a pourable Calcium Sulphoaluminate (CSA) cement-based concrete for rapid repair applications. Due to dynamic events like vehicle strikes, ballistic events, or other dynamic loading events, the dynamic material characteristics are important for understanding how the material will respond. A large diameter Split Hopkinson Pressure Bar (SHPB) was used to test samples of the pourable CSA cement and determine its dynamic material properties in the early strength development phase. 24 samples were tested in 7 day intervals for 28 days. Samples were prepared targeting a length …

Mid-Field Shock And Impulse Estimation Methods For Blast Loading On Tall Targets, Ethan Allan Steward

Doctoral Dissertations

Blast resistant structural design continues to be a major research area for governments around the world due to explosive threats from both state and non-state actors. Many of the typical targets of explosive attacks, such as government buildings, commercial high rise office buildings, and apartment complexes are mid to high-occupancy buildings that present a tall profile relative to the charge size and are often clad in curtain walls. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one …

Shock Wave And Vortex Ring Dynamics From Explosively Driven Shock Tunnels, Rachel Louise Bauer

Doctoral Dissertations

"Blast and shock tubes are frequently used to create shock waves to study their effects and impacts on structures, humans, and personal protective equipment. These tubes are also found in other industries including wind tunnels for aerodynamic testing, jet engines for propulsion research, spacecraft reentry simulations, and industrial applications such as material testing and high-velocity impact studies. Despite their widespread use, there is no standard design, with variations in geometry, size, and energy sources. Current research only evaluates the peak pressure of the shock wave produced and does not consider the effects of changing the size or geometry of the …

Investigation Of Shockwave Behavior To Inform Helmet Design Using Schlieren Imagery And Free-Field Blasts, Cody Jh Thomas

Doctoral Dissertations

"Ballistic resistance of military helmet designs is a prioritized feature to protect warfighters from traumatic brain injury. However, injuries from shock-based threats have not been optimized for warfighter protection and have resulted in the prevalence of blast-induced traumatic brain injury (bTBI). Research gaps were identified in understanding the under wash effect using free field blasts and schlieren imagery. Thus, the following were investigated: (1) overpressure changes on a warfighter’s head due to directionality from a blast, (2) shock wave dampening effects of viscoelastic materials in helmets, and (3) geometric effects of a helmet brim design in the reduction of bTBI. …

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

High Strain Rate Analysis Of 3d Printed Concrete As Compared To Conventionally Cast Concrete, Weston Mcleod Thomsen

Masters Theses

"3D Printed Concrete (3DPC) is a developing method of construction that has advantages over conventional methods, including formwork reduction, complex geometry, and expedited construction. This technology has potential benefits for the military when considering the austere environments that forward operating bases are built in. This study aims to assess 3DPC applications in protective structures that protect critical assets from explosive blasts. These protective structures experience a high-strain rate response during blast loading of the structure, and the effects of this have yet to be analyzed in the literature concerning 3DPC. With the lack of prior research, the focus here will …

Underground Blast Fragmentation Modeling For Use In The Mine-To-Mill Strategy, Lauren Shields

Theses and Dissertations--Mining Engineering

More than 40 years ago, the mine-to-mill concept was introduced in the mining industry by establishing a relationship or link between processing and mining activities. To date, many successful case studies have documented the evident benefits of the mine-to-mill approach. In most cases, the basis of the mine-to-mill approach is to tailor the details of a blast design and its proper execution in order to satisfy specific mineral processing requirements downstream. Most of the available literature and case studies deal with surface mine operations. Due to the relative simplicity of surface mining, the relationship between the powder factor, defined as …

Discrete Element Modeling To Predict Muckpile Profiles From Cast Blasting, Russell Lamont

Theses and Dissertations--Mining Engineering

Movement of overburden or ore from one location to another may be considered the primary physical process of mining. The means by which it is transported is then of primary concern both to economic production and cost control. The geologic characteristics of some mineral deposits, especially coal and phosphates, lend themselves to overburden transport by means of cast blasting, which when efficiently designed has proven itself to be a cheaper method than traditional truck/shovel, dragline, or even dozer push transport. Simultaneously, this movement of a significant portion of overburden using explosives may enable an operation to increase mineral production, as …

Investigating Detonation Parameters Through The Plate Dent Test: A Novel Approach For Characterizing Detonation Curvature And Thickness, Emily Michelle Johnson

Doctoral Dissertations

Detonation is the driving factor behind how an explosive, used in an array of applications, performs. Understanding and measuring detonation parameters of an explosive is key in explosive charge design and application. Currently, determining parameters is costly as the instrumentation needed is expensive in terms of price, maintenance, and personnel. This research examines two methods of determining detonation parameters through measurement of secondary material response to the detonation wave in an effort to provide an alternate, simple, and inexpensive method of measurement. The first of these studies focuses on the Gurney Model and demonstrates that the model's accuracy was diminished …

Prediction Of Blast-Induced Ground Vibrations: A Comparison Between Empirical And Artificial-Neural-Network Approaches, Luis F. Velasquez

Theses and Dissertations--Mining Engineering

Ground vibrations are a critical factor in the rock blasting process. The instantaneous load application exerted by the gas pressure during the detonation process acts on the blasthole walls creating dynamic stresses in the adjacent rock. This triggers different sorts of stress waves, mainly divided into two categories: body and surface waves. The first comprises the P and the S waves, while the second comprises Rayleigh waves. These waves spread concentrically starting at the blast location and move along the ground surface and its interior, being attenuated as they reach further distances.

In most cases, and accepting the hypothesis that …

Effects Of Downwash When Measuring Gas Concentration With Uav-Mounted Gas Sensors, Jacob Lane Brinkman

Doctoral Dissertations

"This research concludes that the downwash region of a rotary-wing unmanned aerial vehicle (UAV) does not produce pressure variations substantial enough to cause significant changes in density-based gas concentration measurements. US regulations evaluate gas concentration as a function of gas density, and accurate concentration measurements are critical for protecting health and safety, which means evaluation of actual downwash effects on measured gas concentration is essential.

During experimentation, the UAV was fixed to a stand in a sealed chamber filled with NOx (NO and NO₂) of constant concentration. The UAV rotors ran at hovering speeds, and gas concentrations were …

Projectile Generator Design For Underground Coal Mine Seal Testing, Ethan Allan Steward

Masters Theses

"Underground coal mines have several dangers, one of the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at …

The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien

Masters Theses

"The effects of a rigid polyurethane foam used as a confinement material on four types of breaching explosives were tested, focusing on the changes in shockwave peak pressures, detonation load compression forces, and brisance cratering abilities. The Plate Dent testing procedure was modified to incorporate a load cell force sensor, and two air overpressure sensors were included adjacent to the blast to quantify each test result. The testing variables focused on the polyurethane foam cure times and thickness volumes around the breaching explosives to determine the breaching charges' optimal energy output capabilities when confined by the foam material. The rigid …

Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer

Doctoral Dissertations

“This research investigates the physical and chemical processes that contribute to the detonation synthesis of silicon carbide nanoparticles. Bulk production of SiC nanoparticles through detonation is possible due to pressures achieved over 20 GPa and temperatures over 2000 K as well as quenching rates in excess of 13 billion K/second. These conditions catalyze reaction and bottom-up molecular growth while retaining particles < 100 nm in diameter. In this work, detonation synthesis of SiC was demonstrated by incorporation of polycarbosilane, an SiC precursor material, into an RDX/TNT explosive matrix prior to detonation. Detonation Synthesis of SiC was also accomplished by reacting elemental silicon with carbon liberated by the detonation of negatively oxygen balanced TNT. Hydrodynamic simulation of a 60:40 mass ratio RDX/TNT detonation created conditions thermodynamically suitable to produce cubic silicon carbide within the first 500 nanoseconds after the passage of the detonation wave while carbon remains chemically reactive for molecular formation. Simulations and experimental tests indicated that loading configuration and impedance mismatch of the precursor additives used in detonation synthesis results in conditions in the additives that exceed the accepted detonation pressure of the explosive by greater than three times. Finally, a full factorial experimental design showed increasing silicon concentration, reducing silicon size, and reducing oxygen balance by adjusting the ratio of RDX to TNT decreased the explosives detonation pressure by 20% and increased the soot yield and concentration of SiC observed in the detonation products by 82% and 442% respectively”--Abstract, page iv.

Investigation Of Anomalous Data Trends During Coal Dust Explosibilty Testing, Jacob Lee Miller

Doctoral Dissertations

Coal dust explosibility is a health and safety concern that has been a recognized hazard for over 100 years. Initial testing by the Author using a Siwek 20L apparatus recorded a secondary maximum pressure at higher dust concentrations (1,000-7,000g/m³) with Pulverized Pittsburgh Coal (PCC). Higher dust concentrations are beyond the typical ASTM E1226 testing procedure but are possible in mining and processing scenarios. No reference documents have been discovered that show a secondary maximum pressure at higher dust concentrations. Literature reviewed identified that once a coal dust concertation generates a peak pressure, the pressure remains constant or decreases …

Investigating The Focusing Effect Of Charge Geometry With Computer Simulations, Witness Plates, And High-Speed Videography, Kelly Ray Williams

Doctoral Dissertations

"Scaled distance is used to calculate a safe standoff radius from the detonation of a known mass of an explosive. It has been shown that varying only the geometry of the charge significantly overdrives regions of the blast wave potentially resulting in hazardous overpressure levels at scaled distance safe radii. Pressure transducers are used to measure overpressure surrounding spherical, cylindrical, and cubic charges to determine if bridge waves were formed at the edges between flat sides as seen in published studies of cylindrical charges. In the fireball field a witness plate is used to evaluate radial energy distribution with a …

Predicting Fracture Extension Around A Borehole Using The Numerical Displacement Discontinuity Method, Nathaniel Schaefer

Theses and Dissertations--Mining Engineering

Prediction of blast damage radius is integral in the optimization of mining safety and production. The damage radius can be related to blasting variables such as fragmentation size as well as overbreak in hard rock. Various methods have been developed to predict and assess damage radius extension for individual holes to aid in blast design. These methods range from experimental and observational techniques to theoretical applications. Some of these methods have been used with a degree of success. However, many of them lack a comprehensive combination of experimental and theoretical contributions. Since post-blast environments are not conducive to assessing whether …

Proof Of Concept For The Development Of A Ground Vibration Sensor System For Future Research In Blasting, John Meuth

Theses and Dissertations--Mining Engineering

Ground vibrations from blasting are one of the leading limitations to mining (underground and surface). There is a need for a low-cost scalable vibration monitoring system to conduct large scale ground vibration projects in the mining industry. Studies conducted on ground vibrations use any number of different sensors to obtain their data, the different sensor capabilities and methods for data processing lead to uncertainties in the research and regulations set for ground vibrations. Commercial Systems do not allow researchers to obtain raw output data, and the data processing procedures are not provided or disclosed for these systems. In order to …

The Effect Of Delay And Sequence On Blasting Fragmentation Results, Tristan Worsey

Theses and Dissertations--Mining Engineering

Blasters use the delay between charges and the firing sequence of the explosive charges to help reduce vibrations and achieve the desired fragmentation. Although delay and sequence are recognized as very important for vibrations and fragmentation, only vibration models consider timing as a variable in the prediction tool, without any known model for fragmentation prediction based on the delay sequence. Of the few fragmentation models available, very few take delay into account and do not give guidance on row delay and/or sequence selections. With the invention of electronic detonators in 1984, there are new avenues to explore with sequence and …

Shock Wave Propagation Behavior At Corners And Crosscuts In Five Small-Scale Tunnel Scenarios, David Pierre Doucet

Masters Theses

"Shock wave propagation in tunnels and other enclosed environments is substantially more complicated than in an open-air or even a surface detonation. There is still much to learn about how shock wave properties change as a wave propagates in an enclosed space, such as a mine tunnel, inside of a building, or city street. The geometry of the enclosure will have a large role in the propagation of the shock wave. This means that many different tunnel designs must be studied. This work tested five different designs using a modular small-scale model. The scenarios tested were Straight-line, Single Turn, Around …

Additive Manufacturing Of Linear Shaped Charges To Address Run Up And Run Down Phenomena, Jason Ho

Masters Theses

”A shaped charge is an explosive device used to focus detonation energy in a desired direction. Additive Manufacturing (AM) can allow greater design freedom and geometric complexity for the liner portion of the shaped charge.

In this work, the following hypotheses were tested: 1) Adjusting the initial apex angle of a linear shaped charge liner reduces the amount of run up that occurs, and 2) implementing a backstop at the end of a linear shaped charge liner reduces the amount of run down that occurs.

Linear shaped charge liners with a continuously changing apex angle were created with additive manufacturing. …

Simplifying Techniques Applied To Computational Fluid Dynamics Modeling Of Methane Explosions, Laura Steeves

Theses and Dissertations--Mining Engineering

Traditional methods of studying underground coal mine explosions are limited to observations and data collected during experimental explosions. These experiments are expensive, time-consuming, and require major facilities, such as the Lake Lynn Experimental Mine. The development of computational fluid dynamics (CFD) modeling of explosions can help minimize the need for large-scale testing. This thesis utilized the commercial CFD software, SC/Tetra, to examine three case studies. The first case study modeled the combustion of methane in a scaled shock tube, measuring approximately 1 foot by 1 foot, by 20.5 feet long, with a methane cloud of 2.5 feet in length, at …

Projectile Impact Effects On A 50 Psi Plug Type Coal Mine Seal, Bruce Albert Von Niederhäusern

Masters Theses

"The current lack of projectile damage criteria for mine seals is assessed to determine if criteria should be developed. Impact experiments were performed on a full-scale 50 psi mine seal to determine failure modes, dynamic stress state, and assess risk to existing operational mine seals. Test projectiles were selected from common underground coal mine items propelled by means of a black powder projectile generator. Projectile velocities attained in testing ranged from approximately 100 to 650 ft/s (30 to 200 m/s). Dynamic strain was measured on the non-impact face to derive the state of stress and estimate failure criteria. Penetration models …

Pressure Versus Impulse Graph For Blast-Induced Traumatic Brain Injury And Correlation To Observable Blast Injuries, Barbara Rutter

Doctoral Dissertations

"With the increased use of explosive devices in combat, blast induced traumatic brain injury (bTBI) has become one of the signature wounds in current conflicts. Animal studies have been conducted to understand the mechanisms in the brain and a pressure versus time graph has been produced. However, the role of impulse in bTBIs has not been thoroughly investigated for animals or human beings.

This research proposes a new method of presenting bTBI data by using a pressure versus impulse (P-I) graph. P-I graphs have been found useful in presenting lung lethality regions and building damage thresholds. To present the animal …

The Mechanics Of Precision Presplitting, Anthony Joseph Konya

Doctoral Dissertations

"Precision Presplitting is a widely used method of presplit blasting for the mining and construction industries. In recent years considerable effort has gone into the development of empirical equations based on field data to be able to better design the Precision Presplit for various rock types and structural environments. However, the most widely discussed theory about the mechanics of the presplit formation, that of shockwave collisions, does not appear to be applicable for this method of presplitting.

This research has disproven this theory based on insufficient magnitude of the shockwave from modeling with basic wave mechanics. Other authors have suggested …

The Behavior Of Suas Under Explosive Loading Conditions And Implications For Safe Operating Procedures, Ashok Em Sudhakar

Doctoral Dissertations

"Drones are increasingly being used for tasks previously unimagined and the beneficial uses are evolving. The United States Congress has envisioned the possible uses of drones for both combating and conveying explosive threats and other harmful and destructive activities. Congress' intent is reflected in new laws (2018) and policies (2019).

All civilian available Small Unmanned Aerial Systems sUASs (Drones), weighing less than 55 pounds, in the current market are not designed for operations in explosive environments. This first of a kind research focuses on further understanding of sUASs response to explosive loading and the public policy implications. This research measured …