Explosives Engineering Commons^™

Significance Of Reagents Addition Sequence On Iron Anionic Reverse Flotation And Their Adsorption Characteristics Using Qcm-D, Ying Hou, Ahmed Sobhy, Yue Wang

Mining Engineering Faculty Research & Creative Works

To explore the influence of reagents addition sequence of the pH regulator and the starch depressant on the anionic reverse flotation of iron oxide, flotation conditional experiments were performed on mixed low-intensity and high-gradient magnetic concentrates which is the flotation feed acquired from the iron processing plant. Besides, quartz crystal micro-balance with dissipative (QCMD) was conducted to detect the adsorption phenomena of the flotation reagent on iron oxide sensors at different addition orders. The outcomes showed that the flotation performance using the pH regulator prior to the depressant was the best. For example, at 1.6 kg/Mg starch dosage, the recovery …

Evaluation Of The Extractive Gold Process: Open-Pit Mining Through Exergy Analysis, Hector I. Velasquez, Carlos Andres Orozco Loaiza, Christian Hasenstab, Natalia A. Cano

Journal of Sustainable Mining

The Colombian mining sector is characterized by the production of coal, nickel, emeralds, gold, and construction materials. It is considered by the National Development Plan of Colombia 2018-2022 as an economic agent that boosts development in the region and one that requires the strengthening of its policies and environmental liability. Therefore, this paper aims to show the importance of implementing methodologies based on the logic of nature (exergy) that objectively indicate the environmental impact of an extractive gold activity, such as open-pit gold mining. The extractive activity or process to be studied consists of the following stages: topsoil removal by …

Exergy Life Cycle Assessment Indicators In Colombian Gold Mining Sector, Natalia A. Cano, Christian Hasenstab, Hector I. Velasquez

Journal of Sustainable Mining

Thermodynamic methods, such as exergy analysis allow the assessment of environmental load (environmental impacts), by calculating the entropy generated or exergy destroyed due to the use of renewable and non-renewable resources along the entire production chain. In this research, exergy analysis will be approached as an extension of LCA to ExLCA (Exergy Life Cycle Assessment), as complementary tools, for sustainability assessment of two gold mining systems in Colombia: open-pit and alluvial mining. It is quantified exergy life cycle efficiencies; Cumulative Energy/ Exergy Demand, by distinguishing between renewable and non-renewable resources used in the process. The energy contained in renewable and …

True Cost Of Coal: Coal Mining Industry And Its Associated Environmental Impacts On Water Resource Development, Noshin Masood, Karen Hudson-Edwards, Abida Farooqi

Journal of Sustainable Mining

Coal is a strategic and essential resource that ensures quality of life, energy security and sustainable development. Being the cheapest source of energy, it is the second after oil that is used to generate 40% of the world's electricity. However, traditional and conventional coal fuel extraction can threaten human health bycontaminating air and water, harming land, and contributing to global warming. The environmental impacts associated with conventional methods of coal mining and consumption can affect all components of the environment, and these impacts may be beneficial or harmful, permanent or temporary, repairable or irreparable, and reversible or irreversible in nature. …

Measurement Of Surface Subsidence And Ground Collapse Caused By Underground Mining In The Boleo Copper District, Mexico, Jong-Gwan Kim

Journal of Sustainable Mining

Subsidence and vertical movements in mines are a challenge in mining operations. To qualify as a controlled mine site, ground movements must be measured regularly during mining operations. Boleo Copper District mine was monitored and the movement during mining operations was measured from Oct. 31, 2018 to March 15, 2019. The evaluation of vertical and horizontal movement was determined in four locations in the mine areas M303, M303S, M303 C, and M305. The exploitation area, which measured approximately 80 x 90 m² with a height of 2.4 m, impacted the surface in the form of cracks. These cracks were …

Recovery And Repurposing Of Thermal Resources In The Mining And Mineral Processing Industry, Shannon H. Mclean, Jeffrey Chenier, Sari Muinonen, Corey A. Laamanen, John A. Scott

Journal of Sustainable Mining

The consumption of energy contributes significantly to the overall cost of operations and the environmental impact of the mining and mineral processing industry. However, despite a few notable exceptions, most of the resulting waste heat produced is dissipated, without recovery, into the environment. There is also a lot of stored heat in mine water which can be tapped into long after a mine has closed. There is, therefore, significant opportunity to improve the industry's sustainability through increasing the amount of waste heat recovered and repurposed.

Mineralogical Variations With The Mining Depth In The Congo Copperbelt: Technical And Environmental Challenges In The Hydrometallurgical Processing Of Copper And Cobalt Ores, Michel Shengo Lutandula, W. S. Kitobo, M. B. Kime, M. P. Mambwe, T. K. Nyembo

Journal of Sustainable Mining

For a long time in the Democratic Republic of Congo, the mining of ores for the production of copper cathodes and salts of cobalt was mostly conducted in the near-surface oxidized mineralization of the Congo Copperbelt. An important part of this mineralization is found in geological settings where copper and cobalt mainly exist as mixtures of oxides and sulfides. With the depletion of surface-rich minerals, mining is taking place at depths where sulfide minerals are prevalent. Using current technologies, the hydrometallurgical processing of ores with high levels of sulfide minerals results in poor metal recovery due to their retention in …

Alternative Methodology To Determine Effective Coefficient Of Methane Diffusion In Coal, Henryk Koptoń

Journal of Sustainable Mining

The article presents the results of research in to the development of an alternative method of determining the effective coefficient of methane diffusion in coal, based on a mathematical model following Fick's second law. The research was conducted based on the recorded courses of methane sorption kinetics in coal samples obtained in laboratory conditions with the precise gravimetric sorption system IGA-001. The value of the coefficient was treated as an element tuning the model in such a way that the average relative error of the ex post was as small as possible. Model verification indicated the correctness of its assumptions. …

In Search Of A Future For Mining: Participative Scenarios For Colombia, Santiago Arango-Aramburo, Ricardo Smith, Patricia Jaramillo, Yris Olaya, Adrian Saldarriaga, Oscar J. Restrepo, Yuly Arboleda, Carla Rua, Sebastian Bernal, Pablo E. Londono, Erik R. Larsen

Journal of Sustainable Mining

We describe and discuss the development of scenarios for the Colombian mining industry. The scenarios were developed with a large group of stakeholders from across the Colombian government, society, and commerce, all with interest in and/or affected by the future of the mining sector. The process resulted in the creation of three different scenarios for the Colombian mining sector to 2030. The article describes the participatory process used for involving the stakeholders, including the workshops and the mapping technique that was used. It also outlines the three scenarios and possible policies that should be considered by the Colombian government in …

Ammonia-Ca-K Competitive Ion-Exchange On Zeolites In Mining Wastewater Treatment: Batch Regeneration And Column Performance, Roberto Martín Narbaitz, Zachary G. Chartrand, Majid Sartaj, Jason Downey

Journal of Sustainable Mining

This manuscript addresses the treatment explosives-impacted mining wastewaters (EIMWW) using ion-exchange to remove elevated levels of ammonia. Repeated batch loading-regeneration cycles were conducted for two commercially available zeolite media used in the treatment of ammonia-ladenEIMWW to establish the effects of competing ions and regeneration solution composition. The Northern Ontario EIMWW tested contained 3.87 meq/L total ammonia (TA) as well as 2.85 meq/L Kþ and 3.9 meq/L Ca2þ.The media studied were a natural clinoptilolite and a modified clinoptilolite (SIR-600). Five regenerant solutions with different NaCl and KCl concentrations were evaluated. The presence of potassium in the regenerant was found to hinder …

The Identification Of Heavy Metal Accumulator Ferns In Abandoned Mines In The Philippines With Applications To Mine Rehabilitation And Metal Recovery, Rene Juna R. Claveria, Teresita R. Perez, Ian A. Navarrete, Rubee Ellaine C. Perez, Brian Christian C. Lim

Journal of Sustainable Mining

This paper focuses on the identification of some plant accumulators of heavy metals that can facilitate mine remediation and rehabilitation in the Philippines and metal recovery or phytomining. Most of these hyperaccumulators are ferns that thrive very well in different terrains and of particular interest are Pityrogramma calomelanos, Pteris vittata, and Pteris melanocaulon that are abundant in abandoned CueAu mining areas. The amounts of Cu and As in the soil and in the aboveground (AG) and belowground (BG) components of the accumulator ferns were determined and the Bioaccumulation Factor (BF) and the Translocation Factor (TF) were derived. Efforts to …

A Lab Study Of Mineral Scale Buildup On Line And Traditional Pe Water Pipes For Acid Mine Drainage, Amanda Pezzuto, Emily Sarver

Journal of Sustainable Mining

Plastic, especially polyethylene (PE), pipe material is increasingly used in mining applications due to its inert nature, flexibility, low density, and low cost. Though resistant to chemical corrosion, it is susceptible to abrasion. To combat this problem, an abrasion-resistant liner is in development. However, it is not yet known how the liner will perform with regards to other common problems that affect pipe systems, such as mineral scale buildup. In mining applications, scale buildup occurs due to the very high contents of suspended and dissolved solids in water or slurry. For example, in systems transporting raw or treated acid mine …

Optimising The Management Of Mining Waste By Means Sentinel-2 Imagery: A Case Study In Joda West Iron And Manganese Mine (India), Daniela Guglietta, Girolamo Belardi, Daniele Passeri, Rosamaria Salvatori, Stefano Ubaldini, Barbara Casentini, Francesca Trapasso

Journal of Sustainable Mining

A smart economy minimizes the production of waste from mining activities and reuses waste as a potential resource, with the goal of moving towards a near-zero waste society. This paper presents integrated multidisciplinary methodology in order to optimise the management of mining waste. The test site is the FeeMn mine in Odisha (India). The mining waste present in the mine has been collected and afterwards X-Ray Powder Diffraction, X-Ray Fluorescence and spectral signatures analysis have been performed for mineralogical, chemical and spectral characterization of the materials. Finally, the classification and mapping of the characterized mining waste was carried out by …

Comments On “Life Cycle Assessment Of Cobalt Extraction Process” By Farjana Et Al. (2019), Rickard Arvidsson, Mudit Chordia, Anders Nordelöf

Journal of Sustainable Mining

Several points of critique are raised against the paper by Farjana et al. (J Sust Mining, 18(3): 150-161, 2019). The first regards the novelty of their paper. The second regards the age and quality of the main source data used. The third regards the description of the system boundary of their main data source.

Prospective Study On Safety Climate Of Surface Mining In Pakistan, Izhar Mithal Jiskani, Saleem Raza Chalgri, Safiullah Memon, Niaz Muhammad Shahani, Abdullah Rasheed Qureshi

Journal of Sustainable Mining

The purpose of this study was to assess miners' perceptions about the safety climate of their workplace. To achieve the research aim, the relationship between demographic characteristics and occupational hazards was first determined, and finally, the relationship of safety climate with occupational hazards and health-seeking behavior was discovered. The data was collected through a self-reporting questionnaire. The results revealed that the subjects have to deal with severe occupational hazards, and they possess poor health-seeking behavior. A safety climate assessment showed that only one of the seven dimensions (i.e. safety communication, learning, and trust in co-worker safety competence) was at …

Effect Of An Eccentric Decoupled Charge On Rock Mass Blasting, Jung-Gyu Kim, Mahrous A. M. Ali, Jong-Gwan Kim

Journal of Sustainable Mining

Experimental and numerical analyses were conducted to investigate the effect of an eccentric loaded contour hole on a rock mass. In the concrete blocks used for the analyses, detonating cords were placed at the centre of the blast hole and eccentrically against the wall of the blast hole. PFC^2D and AUTODYN were used for the numerical analyses, and the results of these software showed that an eccentric decoupled charge can result in the directional development of fractures, thereby enabling the control of cracks in the opposite direction. Even though both types of blasting have identical decoupling indexes, the crack …

A Mechanism Of Electric Charge Losses In Adiabatically Compressed Ferroelectrics, Sergey I. Shkuratov, Jason Baird, Vladimir G. Antipov, Jay B. Chase

Mining Engineering Faculty Research & Creative Works

A ferroelectric depolarized by high strain-rates induced by the passage of adiabatic shock waves releases a high-density electric charge, initiating the generation of high voltage and megawatt power levels. Additionally, this depolarization process alters physical and mechanical properties that might cause energy and electric charge losses in the ferroelectric materials. We report, herein, the results of an experimental study of electric charge losses in Pb0.99(Zr0.95Ti0.05)0.98Nb0.02O3 and Pb0.99(Zr0.52Ti0.48)0.99Nb0.01O3 ferroelectrics subjected to shock compression. We found that electric charge losses mainly occur in the compressed zone of ferroelectric elements, i.e., shock compression is an essential part of the charge loss mechanism. Based …

An Experimental Research On Cationic Reverse Flotation Of Anshan-Type Iron Ores, Zhonghang Chen, Dianbing Zhu, Shujuan Dai, Ahmed Sobhy

Mining Engineering Faculty Research & Creative Works

The mineral processing technology of Anshan-type iron ores has been developed in a rapid speed in recent years, and the combined flowsheet at the core of anionic reverse flotation has become a mainstream in the beneficiation of Anshan-type iron ores in China. With the successful application of this combined flowsheet, some obvious problems are also emerging. Such as high requirement of pulp temperature, complex reagent system, high cost of reagent consumption and so on. In view of this, we have carried out an experimental study on the separation of Anshan type iron ore by cationic reverse flotation. A new collector …

Predicting Fracture Extension Around A Borehole Using The Numerical Displacement Discontinuity Method, Nathaniel Schaefer

Theses and Dissertations--Mining Engineering

Prediction of blast damage radius is integral in the optimization of mining safety and production. The damage radius can be related to blasting variables such as fragmentation size as well as overbreak in hard rock. Various methods have been developed to predict and assess damage radius extension for individual holes to aid in blast design. These methods range from experimental and observational techniques to theoretical applications. Some of these methods have been used with a degree of success. However, many of them lack a comprehensive combination of experimental and theoretical contributions. Since post-blast environments are not conducive to assessing whether …

Proof Of Concept For The Development Of A Ground Vibration Sensor System For Future Research In Blasting, John Meuth

Theses and Dissertations--Mining Engineering

Ground vibrations from blasting are one of the leading limitations to mining (underground and surface). There is a need for a low-cost scalable vibration monitoring system to conduct large scale ground vibration projects in the mining industry. Studies conducted on ground vibrations use any number of different sensors to obtain their data, the different sensor capabilities and methods for data processing lead to uncertainties in the research and regulations set for ground vibrations. Commercial Systems do not allow researchers to obtain raw output data, and the data processing procedures are not provided or disclosed for these systems. In order to …

The Effect Of Delay And Sequence On Blasting Fragmentation Results, Tristan Worsey

Theses and Dissertations--Mining Engineering

Blasters use the delay between charges and the firing sequence of the explosive charges to help reduce vibrations and achieve the desired fragmentation. Although delay and sequence are recognized as very important for vibrations and fragmentation, only vibration models consider timing as a variable in the prediction tool, without any known model for fragmentation prediction based on the delay sequence. Of the few fragmentation models available, very few take delay into account and do not give guidance on row delay and/or sequence selections. With the invention of electronic detonators in 1984, there are new avenues to explore with sequence and …

Shock Wave Propagation Behavior At Corners And Crosscuts In Five Small-Scale Tunnel Scenarios, David Pierre Doucet

Masters Theses

"Shock wave propagation in tunnels and other enclosed environments is substantially more complicated than in an open-air or even a surface detonation. There is still much to learn about how shock wave properties change as a wave propagates in an enclosed space, such as a mine tunnel, inside of a building, or city street. The geometry of the enclosure will have a large role in the propagation of the shock wave. This means that many different tunnel designs must be studied. This work tested five different designs using a modular small-scale model. The scenarios tested were Straight-line, Single Turn, Around …

Additive Manufacturing Of Linear Shaped Charges To Address Run Up And Run Down Phenomena, Jason Ho

Masters Theses

”A shaped charge is an explosive device used to focus detonation energy in a desired direction. Additive Manufacturing (AM) can allow greater design freedom and geometric complexity for the liner portion of the shaped charge.

In this work, the following hypotheses were tested: 1) Adjusting the initial apex angle of a linear shaped charge liner reduces the amount of run up that occurs, and 2) implementing a backstop at the end of a linear shaped charge liner reduces the amount of run down that occurs.

Linear shaped charge liners with a continuously changing apex angle were created with additive manufacturing. …