Mining Engineering Commons^™

Predicting Young’S Modulus Of Indian Coal Measure Rock Using Multiple Regression And Artificial Neutral Network, Sayantan Chakraborty, Rohan Bisai, Rohit Roy, Sathish Kumar Palaniappan, Samir Kumar Pal, Karanam Uma Maheshwar Rao

Journal of Sustainable Mining

Accurate information on Young’s modulus (E) is required for simulating rock deformation in mines; on the other hand, it is very cumbersome to obtain in the laboratory and collecting drilled cores in sufficient amounts, especially in the case of soft rocks, is quite impossible. Empirical equations were deducted for E from easily determinable rock properties, and the final model was selected through different statistical strength parameter tests. The generalization of the equation was verified through the normal distribution tests of residues of the equation. R2 came to be 0.609 and was validated using an artificial neural network with an improved …

Gravity And Electrostatic Separation Of Unburned Coal From A Selected Fly Ash, Krzysztof Wierzchowski, Agnieszka Klupa, Barbara Białecka, Joanna Całus Moszko

Journal of Sustainable Mining

Unburned coal grains make it difficult to use fly ash economically, which causes energy losses in the fuel. The article presents the possibilities of separating unburned coal from selected fly ash. In order to assess the possibility of separation of unburned carbon, the analysis of grain density and ash composition was used. Unburned coal was separated by four methods – one wet gravity and three dry methods. It has been found that despite very fine ash grains, the quality and quantity of separation products are significantly dependent on the separation method used and the separated grains’ qualitative characteristics. The analysis …

Exploring The Characterization, Liberation And Flotation Response Of A Nigerian Low-Grade Copper Ore, Willie Nheta, Omoyemi O. Ola-Omole

Journal of Sustainable Mining

This study explores the characterization, liberation and flotation response of low-grade copper ore from Anka area, Zamfara state Nigeria. The ore was crushed, milled and sieved in accordance with BS 410 standard. It was characterized with XRD, XRF, SEM-EDS and AAS. Froth flotation was carried out with varying %solids, pH, retention time and collector dosages using SEX and sodium oleate. Particle size distribution of the ore shows its economic liberation between -150 and +106 µm while 80% passing corresponds to 175.7 µm using the Gaudin Schuhmann equation. However, according to metallurgical balance calculation, 63 µm proved to have the highest …

Production Management System In A Modern Coal And Coke Company Based On The Demand And Quality Of The Exploited Raw Material In The Aspect Of Building A Service-Oriented Architecture, Artur Dyczko

Journal of Sustainable Mining

The paper deals with the implementation of the JSW Capital Group’s (Poland) Demand and Quality Driven Production Management System (SPPJ – System Zarządzania Produkcją oparty na Popycie i Jakości) using a service-oriented architecture (SOA). The main components of the SPPJ architecture have been characterized, and the scope of their integration has been defined. The individual parts in the first area, i.e. quality management, have been described in detail. Due to the extensive nature of the issue, components in other areas, i.e. planning and scheduling, coal extraction and processing, coke production, as well as sales and logistics, have only been signalled. …

Simplified Cost Models For Underground Mine Evaluation A Handbook For Quick Prefeasibility Cost Estimates - Revised Edition, Thomas W. Camm, Scott A. Stebbins

Mining Engineering

This handbook provides simplified cost models for evaluating underground mines. Regression analysis is used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed production capacity in tonnes per day. A and B are constants determined by the regression analysis. Equations are developed for operating costs in five subcategories: equipment operation, supplies, hourly labor, administration, and sundries. Subcategories for capital costs are: equipment purchase, preproduction underground excavation, surface facilities, engineering & management, contingency, and working capital. Cost models are developed for eight underground …

Molecular Mechanism Study On The Effect Of Nonionic Surfactants With Different Degrees Of Ethoxylation On The Wettability Of Anthracite, Xuanlai Chen, Guochao Yan, You Zhou, Guang Xu, Xuyang Bai, Jiajun Li

Mining Engineering Faculty Research & Creative Works

A serious risk to the production safety of coal mines is coal dust. The wettability of coal may be successfully changed by adding surfactants to water. However, the creation of very effective dust suppressants is constrained by the lack of knowledge about the microscopic interaction mechanism between coal dust and surfactants. In this investigation, we explained macroscopic experimental phenomena from a molecular perspective. The lauryl polyoxyethylene ethers (C12 (EO)n, n = 7,15,23) were selected. The macromolecular model of anthracite with 55 different components was constructed. Surface tension experiments and hydrophilic lipophilic balance (HLB) calculations showed that the ability of surface …

Effect Of Quantitative Textural Specifications On Vickers Hardness Of Limestones, Sasan Ghorbani, Seyed Hadi Hoseinie, Ebrahim Ghasemi, Taghi Sherizadeh

Mining Engineering Faculty Research & Creative Works

It is well-known that the indentation hardness property is influenced by micro-fabric characteristics. The effect of textural characteristics on Vickers indentation hardness is attempted to be interpreted in this research. For this purpose, 12 fresh limestone samples from various quarries were tested to determine the Vickers hardness. Thereafter, quantitative textural parameters were identified and characterized using image processing techniques and micro-fabric analysis based on microphotographs of thin sections. Microphotographs of the thin sections were reviewed and digital boundaries of the grains were clarified and drawn. After preparation and filtering of the digitized thin sections, four basic properties of each grain, …

Evaluating Blast Wave Overpressure From Non-Spherical Charges Using Time Of Arrival From High-Speed Video, Kelly Williams, Catherine E. Johnson

Mining Engineering Faculty Research & Creative Works

Scaled distance is used to predict blast wave overpressure surrounding the detonation of a known mass of explosive under the assumption that the charge geometry is spherical. Altering charge geometry from spherical overdrives regions of the blast wave resulting in areas of higher overpressures than predicted by scaled distance calculations. Empirical data can be used to scale the blast wave overpressure to cylindrical charges, but available overpressure data for more complex geometries is not available in published literature. In the present study the time of arrival of the blast wave was measured from high-speed video and the Rankine-Hugoniot relationship used …

Recovery Of Valuable Metals From Electronic Waste Using A Novel Ammonia-Based Hydrometallurgical Process, Peijia Lin

Theses and Dissertations--Mining Engineering

The growing quantity of waste electrical and electronic equipment (WEEE), also known as electronic waste (E-waste), has been an area of growing public concern. The abundance of valuable metals contained in waste printed circuit boards (WPCBs) has made it a promising secondary resource, especially for Cu and Au. Although the recovery of metals from WPCBs via hydrometallurgical routes has been studied extensively over the past 20 years, most of the research has been limited in the laboratory. In current hydrometallurgical processes, strong acids and expensive oxidizers are often used to ensure a high recovery of metals without considering the sustainability …

A Laboratory And Numerical Investigation Of The Strength Of Irregularly Shaped Pillars, Zachary Wedding

Theses and Dissertations--Mining Engineering

Underground mining operations utilize the room-and-pillar mining method that extracts the orebody and creates ‘rooms’ and leaves the remaining in-situ material as ‘pillars’ to support the overburden. Room-and-pillar mines are traditionally designed in square or rectangular-shaped pillars. This work presents laboratory experiments testing the compressive strengths of specimens modeled after square and parallelogram-shaped pillars and numerical models of square and -parallelogram-shaped pillar systems. The uniaxial compressive strength of the specimens’ shape and the observations of the extent of the specimen core post-failure were analyzed. There was insufficient evidence from the laboratory experiments to conclude that there is a difference in …

Prediction And Optimization Of Tower Mill Grinding Power Consumption Based On Ga-Bp Neural Network, Ziyang Wang, Ying Hou, Ahmed Sobhy

Mining Engineering Faculty Research & Creative Works

Grinding is commonly responsible for the liberation of valuable minerals from host rocks but can entail high costs in terms of energy and medium consumption, but a tower mill is a unique power-saving grinding machine over traditional mills. In a tower mill, many operating parameters affect the grinding performance, such as the amount of slurry with a known solid concentration, screw mixer speed, medium filling rate, material-ball ratio, and medium properties. Thus, 25 groups of grinding tests were conducted to establish the relationship between the grinding power consumption and operating parameters. The prediction model was established based on the backpropagation …

Prediction Of Blast-Induced Ground Vibrations: A Comparison Between Empirical And Artificial-Neural-Network Approaches, Luis F. Velasquez

Theses and Dissertations--Mining Engineering

Ground vibrations are a critical factor in the rock blasting process. The instantaneous load application exerted by the gas pressure during the detonation process acts on the blasthole walls creating dynamic stresses in the adjacent rock. This triggers different sorts of stress waves, mainly divided into two categories: body and surface waves. The first comprises the P and the S waves, while the second comprises Rayleigh waves. These waves spread concentrically starting at the blast location and move along the ground surface and its interior, being attenuated as they reach further distances.

In most cases, and accepting the hypothesis that …

An Acid Baking Approach To Enhance Rare Earth Element Recovery From Bituminous Coal Sources, Ahmad Nawab

Theses and Dissertations--Mining Engineering

Rare earth elements (REE) are a group of 17 elements typically classified as light and heavy rare earth elements, which play a crucial role in developing the latest technologies for energy, defense, and medical sectors. Even though REEs have been found in more than 200 minerals, only bastnaesite, monazite and xenotime are commercially exploited for REE extraction. However, the recent exponential increase in REE demand has spurred countries such as the United States into research for the extraction of REEs from secondary sources such as coal, acid mine drainage, and coal ash. Several coal sources (e.g., Fire Clay seam coal) …

Explosion Resistance Of Reinforced Concrete Refuge Alternative Wall Under Certain Abutment Loading, K. E. Karadeniz, D. Guner, Taghi Sherizadeh

Mining Engineering Faculty Research & Creative Works

Build-in-place (BIP) refuge alternatives (RAs) are used to provide safe havens for miners unable to escape their working area after an accident like an explosion. These underground infrastructures are built over time in various locations and might expose to mining-induced stresses. The convergences related to these stress redistributions around the mine openings might change their structural integrity and, subsequently, the explosion resistivity. Studying the effect of increasing vertical load like abutment stress on such underground mine stopping for the explosion resistance is difficult because repetitive explosion experiments on these structures are perilous and challenging. This study uses two case studies …

Molecular Mechanism Study On The Effect Of Nonionic Surfactants With Different Degrees Of Ethoxylation On The Wettability Of Anthracite, Xuanlai Chen, Guochao Yan, You Zhou, Guang Xu, Xuyang Bai, Jiajun Li

Mining Engineering Faculty Research & Creative Works

A serious risk to the production safety of coal mines is coal dust. The wettability of coal may be successfully changed by adding surfactants to water. However, the creation of very effective dust suppressants is constrained by the lack of knowledge about the microscopic interaction mechanism between coal dust and surfactants. In this investigation, we explained macroscopic experimental phenomena from a molecular perspective. The lauryl polyoxyethylene ethers (C12 (EO)n, n = 7,15,23) were selected. The macromolecular model of anthracite with 55 different components was constructed. Surface tension experiments and hydrophilic lipophilic balance (HLB) calculations showed that the ability of surface …

Molecular Mechanism Study On The Effect Of Nonionic Surfactants With Different Degrees Of Ethoxylation On The Wettability Of Anthracite, Xuanlai Chen, Guochao Yan, You Zhou, Guang Xu, Xuyang Bai, Jiajun Li

Mining Engineering Faculty Research & Creative Works

A serious risk to the production safety of coal mines is coal dust. The wettability of coal may be successfully changed by adding surfactants to water. However, the creation of very effective dust suppressants is constrained by the lack of knowledge about the microscopic interaction mechanism between coal dust and surfactants. In this investigation, we explained macroscopic experimental phenomena from a molecular perspective. The lauryl polyoxyethylene ethers (C₁₂ (EO)_n, n = 7,15,23) were selected. The macromolecular model of anthracite with 55 different components was constructed. Surface tension experiments and hydrophilic lipophilic balance (HLB) calculations showed that the …

An Eye Tracking Based Framework For Safety Improvement Of Offshore Operations, Muhammad A. Raza, Raj Kiran, Saima Ghazal, Ziho Kang, Saeed Salehi, Edward Cokely, Jiwon Jeon

Mining Engineering Faculty Research & Creative Works

Offshore drilling operations consist of complex and high-risk processes. Lack of situational awareness in drilling operations has become an important human factor issue that causes safety accidents. Prolonged work shifts and fatigue are some of the crucial issues that impact performance. Eye tracking technology can be used to distinguish the degree of awareness or alertness of participants that might be related to fatigue or onsite distractions. Oculomotor activity can be used to obtain visual cues that can quantify the drilling operators' situational awareness that might enable us to develop warning alarms to alert the driller. Such systems can help reduce …

Prediction Of Dynamic Subsidence In The Proximity Of Longwall Panel Boundaries, Jesus David Romero Benitez

Theses and Dissertations--Mining Engineering

The development of mining subsidence has a dynamic character, and it is related to the mining rate and a time coefficient. Reliable prediction of dynamic deformations is important when planning to undermine important structures that cannot account for large relative deformations and or large horizontal strains. This thesis discusses subsidence development for a number of points over a retreating longwall panel in the eastern US. The prediction points are at different distances from the excavation rib and, therefore, present a different response in terms of dynamic movements. Final movements, i.e., measurements after the panel was fully extracted, were used to …

Assessment Of Air Overpressure From Blasting Using Computational Fluid Dynamics, Cecilia Estefania Aramayo

Theses and Dissertations--Mining Engineering

Air overpressure is a shock wave that occurs when explosives detonate and travel through the air. This can cause damage and annoyance in mining blasts, making it a significant concern for the surroundings of the operation. Currently, the cube root scale distance is used to predict air overpressure, but this method has limitations. To accurately determine air overpressure behavior, a new method is needed. Computational fluid dynamics (CFD) is a reliable and advanced technique that can simulate and solve complex physical problems, including the behavior of air overpressure. In this thesis, two techniques, the bursting balloon, and total pressure boundary, …

Distinct Element Analysis Of Various Structural Element Responses For Coal Rib Support Simulation, A. Kirmaci, D. Guner, K. Karadeniz, Taghi Sherizadeh

Mining Engineering Faculty Research & Creative Works

Understanding the bolt responses for the efficacy of bolt performance during coal rib support applications plays a key role in controlling the stability of underground coal mine openings. Conducting pull-out tests is imperative to gain a better understanding of these responses. Field conditions such as block volume and degree of cleating may significantly impact bolt performance. These field conditions can be efficiently implemented in numerical modeling approaches, and selecting a proper structural element type for these numerical studies is crucial. This study developed a pull-out test model and compared the performance of structural elements as support members in the coal …

An Entropy-Based Risk Index (Eri) Of Mining Health And Safety Using Clustering And Statistical Methods, Dharmasai Eshwar Reddy Sirigiri

Dissertations, Master's Theses and Master's Reports

Over the last decade, the mining industry has seen a significant reduction in the number of fatalities in the United States. However, the annual employee hours have also decreased during the same period. Therefore, it is crucial to evaluate the historical mining data and identify the potential risks of a mine through the mine risk index. The risk indicators also describe the severity of accidents and injuries at mine sites. The variables such as citation, order, significant & substantial citations, lost time, and no lost time injuries and penalties are considered for the determination of the risk index. However, using …

Verification Of Oil Recovery Mechanism Through Alteration Of Relative Permeability Curve And Analytical Measurements, Tina Tharn

Chulalongkorn University Theses and Dissertations (Chula ETD)

In the petroleum production industry, there are several methods that can be utilized to increase oil recovery. These methods are so-called Enhanced Oil Recovery (EOR). Nowadays, Low Salinity Water Flooding (LSWF) is one of the considerable of those techniques due to its cost and simplicity. However, understanding its main oil recovery mechanism is still limited. Therefore, the investigation of oil mechanism provided by LSWF would help refine its application to oilfields. In this study, the Johnson–Bossler–Naumann (JBN) approach is employed to examine relative permeability curves during LSWF in different rock formations including clean sandstone (SS), shaly-sandstone (SHS), and dolostone (DL). …

Moving Towards Sustainable Mining Communities: The Case Of The Community-Led Non-Cyanide Non-Mercury Cold Extraction Method (Clinn-Cem) In Compostela Valley, Philippines, Rowee Joy S. Decena

Journal of Public Affairs and Development

The small-scale mining industry and communities are left behind in terms of development. They are confronted with economic, environmental, and social problems. Thus, to address these problems and move towards sustainable development, this social development research explores how CLINN-GEM, as a technological innovation, contributes to achieving sustainable mining communities. The researcher employs a single case study approach and adopts qualitative methods in data gathering and analysis. Data gathering methods include document reviews, guided tour, key informant interviews with seven informants, focus group discussions with the operations group and the members of the project staff, and a structured learning exercise with …

Effects Of Downwash When Measuring Gas Concentration With Uav-Mounted Gas Sensors, Jacob Lane Brinkman

Doctoral Dissertations

"This research concludes that the downwash region of a rotary-wing unmanned aerial vehicle (UAV) does not produce pressure variations substantial enough to cause significant changes in density-based gas concentration measurements. US regulations evaluate gas concentration as a function of gas density, and accurate concentration measurements are critical for protecting health and safety, which means evaluation of actual downwash effects on measured gas concentration is essential.

During experimentation, the UAV was fixed to a stand in a sealed chamber filled with NOx (NO and NO₂) of constant concentration. The UAV rotors ran at hovering speeds, and gas concentrations were …

Analyzing The Effectiveness Of The Gurney Method For Small Scale Fragmentation Propulsion Using Exploding Bridgewire Detonators, Emily M. Johnson, Rachel L. Bauer, Catherine E. Johnson

Mining Engineering Faculty Research & Creative Works

Explosives are common in military, mining, and construction applications where the explosive properties are understood, but mechanics of how the explosive's energy fragments and throws materials are less known. Considering the type of confining material around an explosive, creates variability in fragmentation behavior due to the individual material characteristics. The most common method for assessing fragmentation behavior is the Gurney method, which eliminates any consideration of fragmenting material properties. The Gurney method assumes that, on a large scale, the inconsistencies in material are irrelevant and only the mass of the confiner need be considered. However, it is known in many …

A Novel Technique For The Quantitative Determination Of Wettability Of A Severely Heterogeneous Tight Carbonate Reservoir, Saleh Al-Sayegh, Ralph E. Flori, Waleed Al-Bazzaz, Abdulaziz Abbas, Ali Qubian, Hasan Al-Saedi

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The objective of this study is to accurately measure the wettability contact angle of a cretaceous carbonate reservoir in a vertical well set-up known for as an unconventional tight carbonate oil reservoir. Also, to investigate the relative heterogeneity of these samples using digitally captured images; these images accurately capture natural pore-system in this carbonate rock samples and their wettability performance attributed towards building a vertical depth wettability/heterogeneity model. To capture, measure and model natural tight matrix static contact angle wettability in order to understand their new physics that will advance unconventional tight oil reservoir characterization. Entire vertical well depth reservoir …

Practical Imaging Applications Of Wettability Contact Angles On Kuwaiti Tight Carbonate Reservoir With Different Rock Types, Saleh Al-Sayegh, Ralph E. Flori, Waleed Al-Bazzaz, Sohaib Kholosy, Hasan Al-Saedi, Abdulaziz Abbas, Ali Qubian

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This study focuses on a tight carbonate reservoir which is located in Northern Kuwait and is classified as an unconventional reservoir. A practical imaging technique of wettability contact angle (θ°) presents "big data" as well as relative-permeability (Krw and Kro) measurements. Also, modeling, through rock image technology, the vast well-documented grain/pore boundary morphology available inside fresh rock fragments have achieved good results. Conventional laboratory relative-permeability experiments are expensive and time-consuming. This study introduces a novel method to measure/calculate relative permeability through fast, less expensive, non-destructive, and environmentally friendly techniques of imaging technology. One tight carbonate reservoir is selected, imaged, processed, …

Investigating Pore Body, Pore Throat, Nano-Pore Wettability Preference In Several Unconventional Kuwaiti Carbonate Reservoirs, Saleh Al-Sayegh, Ralph E. Flori, Hussain Alajaj, Waleed Hussien Al-Bazzaz

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This study will investigate measuring the wettability contact angles of native unconventional tight carbonate as well as other unconventional pore system reservoir samples that hosts varied pore shapes and subsequent wettability contact angle distributions in both reservoir matrix and possible natural fractures. Also, the investigation will include validation of the grain/ pore-wall wettability regions and classify the natural wettability preference available inside pores of the rock and their overall wettability performance and recovery efficiency contributions. Further investigation will include modeling pore throat contact angle wettability, and to understand their new physics that will advance reservoir characterization and oil recovery improvement.

Kuwaiti Carbonate Reservoir Oil Recovery Prediction Through Static Wettability Contact Angle Using Machine Learning Modeling, Saleh Al-Sayegh, Ralph E. Flori, Waleed Hussien Al-Bazzaz, Hasan Al-Saedi, Mostafa Al-Kaouri, Ali Qubian

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The objective of this study is to predict EOR efficiencies through static wettability contact angle measurement by Machine Learning (ML) modeling. Unlike conventional methods of measuring static wettability contact angle, the unconventional digital static wettability contact angle is captured and measured, then (ML) modeled in order to forecast the recovery based on wettability distribution phenomenon. Due to success in big data collection from reservoir imaging samples, this study applies data science lifecycle logic and utilizes Machine Learning (ML) models that can predict the recovery through wettability contact angles and thus identify the treatment of oil recovery for a candidate reservoir. …

Analysis Of The Root Causes Of Fatal Injuries In The United States Surface Mines Between 2008 And 2021., Maria Fernanda Quintero

Graduate Theses, Dissertations, and Problem Reports (ETD)

Mining has long been recognized as a hazardous industry worldwide. An annual average rate of 10.3 fatal injuries per 100,000 workers was recorded in the United States between 2008 and 2021 (MSHA, 2022). This rate can be compared with the average of the industries with the highest average rates of fatal injuries—agriculture, forestry, fishing, and hunting; transportation and warehousing; and construction—which had average rates of 23.5, 13.1, and 9.9 fatal injuries per 100,000 workers, respectively, during the same period in the Unites States (U.S. Bureau of Labor Statistics, 2023).

The scope of this research is related to the fatal injuries …