Open Access. Powered by Scholars. Published by Universities.®

Mining Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Mining Engineering Faculty Research & Creative Works

Articles 271 - 300 of 317

Full-Text Articles in Mining Engineering

Pulsed Charging Of Capacitor Bank By Compact Explosive-Driven High-Voltage Primary Power Source Based On Longitudinal Shock Wave Depolarization Of Ferroelectric Ceramics, Sergey I. Shkuratov, Jason Baird, Evgueni F. Talantsev, Yaroslav Tkach, Larry L. Altgilbers, Allen H. Stults, Stanislav V. Kolossenok Jan 2005

Pulsed Charging Of Capacitor Bank By Compact Explosive-Driven High-Voltage Primary Power Source Based On Longitudinal Shock Wave Depolarization Of Ferroelectric Ceramics, Sergey I. Shkuratov, Jason Baird, Evgueni F. Talantsev, Yaroslav Tkach, Larry L. Altgilbers, Allen H. Stults, Stanislav V. Kolossenok

Mining Engineering Faculty Research & Creative Works

Results of the investigation of the operation of autonomous ultracompact explosive-driven high-voltage primary power sources based on longitudinal (when the shock wave propagates along the polarization vector P0) shock wave depolarization of ferroelectric materials in the open circuit and charging modes are presented. The energy-carrying elements of shock wave ferroelectric generators (FEGs) were poled lead zirconate titanate (PZT) Pb(Zr52Ti48)O3 polycrystalline piezoelectric ceramic disks with volume 0.35 cm3. The PZT modules were shock compressed in the stress range from 1.5 to 3.8 GPa by a longitudinal shock wave generated by high explosives. In the charging mode, the FEGs provided pulsed power …

Go to article

Performance Of A Bgo Pet/Ct With Higher Resolution Pet Detectors, John W. Wilson, Timothy G. Turkington, J. J. Williams, James G. Colsher, D. L. Mcdaniel, C. L. Kim, Steven G. Ross, C. W. Stearns, S. D. Wollenweber Jan 2005

Performance Of A Bgo Pet/Ct With Higher Resolution Pet Detectors, John W. Wilson, Timothy G. Turkington, J. J. Williams, James G. Colsher, D. L. Mcdaniel, C. L. Kim, Steven G. Ross, C. W. Stearns, S. D. Wollenweber

Mining Engineering Faculty Research & Creative Works

A new PET detector block has been designed to replace the standard detector of the Discovery ST PET/CT system. The new detector block is the same size as the original, but consists of an 8/spl times/6 (tangential× axial) matrix of crystals rather than the original 6/spl times/6. The new crystal dimensions are 4.7× 6.3× 30 mm/sup 3/ (tangential× axial× radial). Full PET/CT systems have been built with these detectors (Discovery STE). Most other aspects of the system are identical to the standard Discovery ST, with differences including the low energy threshold for 3D imaging (now 425 keV) and front-end electronics. …

Go to article

Depolarization Of A Pb(Zr₅₂Ti₄₈)O₃ Polycrystalline Piezoelectric Energy-Carrying Element Of Compact Pulsed Power Generator By A Longitudinal Shock Wave, Sergey I. Shkuratov, Evgueni F. Talantsev, Jason Baird, Henryk Temkin, Yaroslav Tkach, Larry L. Altgilbers, Allen H. Stults Jan 2005

Depolarization Of A Pb(Zr₅₂Ti₄₈)O₃ Polycrystalline Piezoelectric Energy-Carrying Element Of Compact Pulsed Power Generator By A Longitudinal Shock Wave, Sergey I. Shkuratov, Evgueni F. Talantsev, Jason Baird, Henryk Temkin, Yaroslav Tkach, Larry L. Altgilbers, Allen H. Stults

Mining Engineering Faculty Research & Creative Works

A poled lead zirconate titanate Pb(Zr52Ti48)O3 polycrystalline piezoelectric ceramic energy-carrying element of a compact explosive-driven pulsed power generator was depolarized by an explosive shock wave traveling along the polarization vector P0. We show that shock wave compression of a ferroelectric energy-carrying element at pressures of 1.5-3.8 GPa caused almost complete depolarization of the sample. The shock wave velocity in the Pb(Zr52Ti48)O3 was determined to be 3.94 ± 0.27 km/s. The electric charge stored in the ferroelectrics, due to their remnant polarization, is released during a short time interval, and can be transformed into pulsed power. Compact explosive-driven sources of primary …

Go to article

Image Quality Vs. Nec In 2d And 3d Pet, John W. Wilson, Timothy G. Turkington, Josh M. Wilson, James G. Colsher, Steven G. Ross Jan 2005

Image Quality Vs. Nec In 2d And 3d Pet, John W. Wilson, Timothy G. Turkington, Josh M. Wilson, James G. Colsher, Steven G. Ross

Mining Engineering Faculty Research & Creative Works

To investigate the relationship between NEC and image quality to 2D and 3D PET, while simultaneously optimizing 3D low energy threshold (LET), we have performed a series of phantom measurements. The phantom consisted of 46 1 cm fillable hollow spheres on a random grid inside a water-filled oval cylinder, 21 cm tall, 36 cm wide, and 40 cm long. The phantom was imaged on a Discovery ST PET/CT system (GE Healthcare, Milwaukee, WI) in a series of 3 min scans as it decayed from an activity of 7.2 mCi. The scans included LET settings of 375,400, and 425 keV in …

Go to article

Method Of Creating Ultra-Fine Particles Of Materials Using A High-Pressure Mill, Marian Mazurkiewicz, B. E. Conrad Jan 2004

Method Of Creating Ultra-Fine Particles Of Materials Using A High-Pressure Mill, Marian Mazurkiewicz, B. E. Conrad

Mining Engineering Faculty Research & Creative Works

A method for creating ultra-fine particles of material using a high-pressure mill is described. The method includes placing a material in a first chamber and subjecting the material to a high-pressure fluid jet to divide it into particles. These particles are then transferred to a second chamber in which they are subjected to cavitation to further divide the particles into relatively smaller particles. These relatively smaller particles are then transferred to a third chamber, in which the particles collide with a collider to still further divide them into ultra-fine particles of the material. The mill of the present invention includes …

Go to article

Compact High-Voltage Generator Of Primary Power Based On Shock Wave Depolarization Of Lead Zirconate Titanate Piezoelectric Ceramics, Sergey I. Shkuratov, Evgueni F. Talantsev, Latika Menon, Henryk Temkin, Jason Baird, Larry L. Altgilbers Jan 2004

Compact High-Voltage Generator Of Primary Power Based On Shock Wave Depolarization Of Lead Zirconate Titanate Piezoelectric Ceramics, Sergey I. Shkuratov, Evgueni F. Talantsev, Latika Menon, Henryk Temkin, Jason Baird, Larry L. Altgilbers

Mining Engineering Faculty Research & Creative Works

The design and performance of a compact explosive-driven high-voltage primary power generator is presented. The generator utilizes a fundamental physical effect—depolarization of ferroelectric materials under longitudinal shock wave impact, when the shock wave is initiated along the polarization vector P. These primary power sources, containing energy-carrying elements made of lead zirconate titanate poled piezoelectric ceramics, with the volume from 0.35 to 3.3 cm3, are capable of producing pulses of high voltage with amplitudes up to 21.4 kV. The amplitude and full width at half-maximum of the high-voltage pulses are directly proportional to the thickness of the energy-carrying element, with coefficients …

Go to article

Adjusting The Low Energy Threshold For Large Bodies In Pet, John W. Wilson, Timothy G. Turkington, James G. Colsher Jan 2004

Adjusting The Low Energy Threshold For Large Bodies In Pet, John W. Wilson, Timothy G. Turkington, James G. Colsher

Mining Engineering Faculty Research & Creative Works

The performance of a PET scanner on three different phantom sizes was studied as a function of low energy threshold (LET). Phantom cross sections ranged from 20 cm diameter circular to 28 cm x 43 cm oval and LET''s ranged from 350 keV to 475 keV, in 25 keV increments. System sensitivity, scatter fraction, and NEC were measured over a wide range of radioactivity levels. Increasing the low energy threshold lowered both sensitivity and scatter fraction. The statistical quality of the raw data was maximized for the 425 keV setting for all three phantoms. System stability and uniformity of response …

Go to article

Optimizing Sequential Dual Tracer P.E.T. Studies Using A Combined 2d/3d Imaging Protocol, John W. Wilson, S. Borges-Neto, Timothy G. Turkington, James G. Colsher, R. E. Reiman, R. E. Coleman Jan 2004

Optimizing Sequential Dual Tracer P.E.T. Studies Using A Combined 2d/3d Imaging Protocol, John W. Wilson, S. Borges-Neto, Timothy G. Turkington, James G. Colsher, R. E. Reiman, R. E. Coleman

Mining Engineering Faculty Research & Creative Works

We have investigated a combined 2D/3D protocol for minimizing contamination in dual tracer P.E.T. studies in which the tracers are administered on a timescale that is short compared to the half-lives. We have performed a series of phantom studies on an Advance and a Discovery ST (GE Healthcare Technologies), using a torso phantom with cardiac insert (Data Spectrum Corporation) to simulate a combined FDG and NH3 scan protocol for a patient with ischemia. The phantom was imaged in a series of alternating 2D/3D acquisitions as it decayed over 6 half-lives. By comparing 2D and 3D images, we have verified that …

Go to article

Method Of Scrapping Steel Structures, G. E. Shapiro, Paul Nicholas Worsey Jan 2003

Method Of Scrapping Steel Structures, G. E. Shapiro, Paul Nicholas Worsey

Mining Engineering Faculty Research & Creative Works

A method of breaking up a structure for the recovery of steel as scrap. The structure has steel plates forming a compartment secured to framing in the compartment. The method includes at least partially filling the compartment with a substantially incompressible substance and placing explosive in the substance in the compartment. The explosive is sufficient and adapted on detonation thereof to pressurize the compartment to the extent of causing separation of the plates from the framing. The method further includes detonating the explosive.

Go to article

Graphite Platelet Nanostructures, Marian Mazurkiewicz Jan 2002

Graphite Platelet Nanostructures, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

Separated graphite nanostructures are formed of thin graphite platelets having an aspect ratio of at least 1,500:1. The platelets have an angular geometric structure and may be fully independent from an original graphite particle, or partially attached to the particle. The graphite platelets have an average thickness in the range of 1-100 nm. The graphite nanostructures are created from synthetic or natural graphite using a high-pressure mill. Fluid jets of the high-pressure flaking mill cause fluid to enter the tip of cracks in the graphite particles, which creates tension at the tip. This tension causes the cracks to propagate along …

Go to article

The Causes Of Armature Surface Fracturing Within Helical Flux-Compression Generators, Jason Baird, Paul Nicholas Worsey Jan 2002

The Causes Of Armature Surface Fracturing Within Helical Flux-Compression Generators, Jason Baird, Paul Nicholas Worsey

Mining Engineering Faculty Research & Creative Works

Aluminum and copper tubes filled with explosive were tested during this study of high strain rate effects, as an adjunct to helical flux-compression generator research at the University of Missouri-Rolla, directly affecting the understanding of flux cutoff and high strain-rate changes in generator armatures. Longitudinal cracks characteristically developed in the outer surface of armatures at a smaller expansion ratio than predicted. These cracks occurred within two diameters of the detonator end of the armature but did not extend when the tubing expanded under explosive pressurization. Such cracks appear to cause magnetic flux cutoff, and flux losses seriously affect energy conversion …

Go to article

Apparatus For Comminution Of Solid Materials Using A Processor-Controlled Liquid Jet, Marian Mazurkiewicz Jan 2002

Apparatus For Comminution Of Solid Materials Using A Processor-Controlled Liquid Jet, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

The present invention is directed to a tire comminution apparatus that is of simple construction and that can be operated without excessive maintenance. According to the present invention, a vehicle tire of any size or composition can be comminuted with essentially the same comminution apparatus. The comminution apparatus includes a freely moving lance with a nozzle for transforming a liquid into a high velocity liquid jet. The lance is positioned and controlled such that the liquid jet impacts the tire thereby separating it into its component parts. The comminution apparatus may be computer controlled.

Go to article

Design Of A Hypersonic Waterjet Apparatus Driven By High Explosives, B. L. Weeks, J. Klosterman, Paul Nicholas Worsey Aug 2001

Design Of A Hypersonic Waterjet Apparatus Driven By High Explosives, B. L. Weeks, J. Klosterman, Paul Nicholas Worsey

Mining Engineering Faculty Research & Creative Works

The design and construction of a hypersonic waterjet apparatus is described. Jet velocities from 0.5 to 5 km/s have been achieved using a high explosive charge. Images are obtained in situ on various target substrates using a high-speed framing camera. Experimental results are shown for the impact of high velocity waterjets on propellants and high explosive samples. By observing the impact of the waterjet at a wide range of velocities a safety threshold can be determined where no reaction takes place.

Go to article

Surface Fracturing Of Armatures Within Helical Flux-Compression Generators, Paul Nicholas Worsey, Jason Baird Jan 2001

Surface Fracturing Of Armatures Within Helical Flux-Compression Generators, Paul Nicholas Worsey, Jason Baird

Mining Engineering Faculty Research & Creative Works

Tubes of aluminum and of copper filled with C-4 high-explosive were tested during this study of high strain rate effects within thin metallic structures performed as an adjunct to helical flux-compression generator research at the University of Missouri-Rolla. Focusing on the stresses within a relatively thin metallic structure when brisant explosives abutting the structure are detonated, this study directly affects the understanding of flux cutoff and high strain-rate resistivity changes in an expanding armature. The detonation wave is compressive, and the shock waves resulting from its transmission into a thin metallic structure cause both compressive and tensile regions, posing an …

Go to article

Effects Of Defects On Armatures Within Helical Flux-Compression Generators, Jason Baird, Paul Nicholas Worsey, Mark F. C. Schmidt Jan 2001

Effects Of Defects On Armatures Within Helical Flux-Compression Generators, Jason Baird, Paul Nicholas Worsey, Mark F. C. Schmidt

Mining Engineering Faculty Research & Creative Works

Tubes of aluminum and copper filled with C-4 high-explosive were tested during this study of the effects of explosive flaws and voids, their sizes and locations, and of the effects of armature machining tolerances on the expansion characteristics of armatures within helical flux-compression generators. Flaws and voids were introduced into the explosive fill of 6061-T6 aluminum armatures during assembly. The defects were located along the major axis of the fill, midway between the major axis and the explosive/armature interface, and at the interface. The resulting effects on armature expansion were recorded by high-speed framing camera, intensified charge-coupled display (ICCD) photography …

Go to article

Method Of Creating Ultra-Fine Particles Of Materials Using A High-Pressure Mill, Marian Mazurkiewicz Jan 2001

Method Of Creating Ultra-Fine Particles Of Materials Using A High-Pressure Mill, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

A method for creating ultra-fine particles of material using a high-pressure mill is described. The method includes placing a material in a first chamber and subjecting the material to a high-pressure liquid jet to divide it into particles. These particles are then transferred to a second chamber in which they are subjected to cavitation to further divide the particles into relatively smaller particles. These relatively smaller particles are then transferred to a third chamber, in which the particles collide with a collider to still further divide them into ultra-fine particles of the material. The mill of the present invention includes …

Go to article

Optical Diagnostics On Helical Flux Compression Generators, A. A. Neuber, J. C. Dickens, H. Krompholz, M. F. C. Schmidt, Jason Baird, Paul Nicholas Worsey, M. Kristiansen Oct 2000

Optical Diagnostics On Helical Flux Compression Generators, A. A. Neuber, J. C. Dickens, H. Krompholz, M. F. C. Schmidt, Jason Baird, Paul Nicholas Worsey, M. Kristiansen

Mining Engineering Faculty Research & Creative Works

Explosively driven magnetic flux compression (MFC) has been object of research for more than three decades. Actual interest in the basic physical picture of flux compression has been heightened by a newly started Department of Defense (DoD) Multi-University Research Initiative. The emphasis is on helical flux compression generators comprising a hollow cylindrical metal liner filled with high explosives and at least one helical coil surrounding the liner. After the application of a seed current, magnetic flux is trapped and high current is generated by moving, i.e., expanding, the liner explosively along the winding of the helical coil. Several key factors …

Go to article

Method For Introducing Substances Into Living Cells And Tissues, Marian Mazurkiewicz Jan 2000

Method For Introducing Substances Into Living Cells And Tissues, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

A method of introducing a biological substance into living target cells, the method comprising dispersing a liquid containing the biological substance into microdroplets and propelling the microdroplets toward to the target cells.

Go to article

Integration Of Csab And Abet, Lee W. Saperstein, Kenneth Martin, Doris K. Lidtke Jan 2000

Integration Of Csab And Abet, Lee W. Saperstein, Kenneth Martin, Doris K. Lidtke

Mining Engineering Faculty Research & Creative Works

The Accreditation Board for Engineering and Technology, Inc. (ABET) and the Computing Sciences Accreditation Board (CSAB) signed a Memorandum of Agreement in November 1998 to integrate CSAB''s accreditation services with ABET, with a transition time of approximately two years. During the interim period, the operations of the Computer Science Accreditation Commission (CSAC) are contracted by CSAB to ABET. A committee with CSAC, CSAB, and ABET representation is working to set up the new commission for accrediting programs in the computing sciences. This new commission will probably be called the Computing Accreditation Commission (CAC). Other activities are underway to try to …

Go to article

Experimental Testing And Modeling Of Automotive Automatic Belt Tensioners, Jiaxin Zhao, Clark R. Barker, Larry Oliver, William Breig, Joey Edson Jan 1998

Experimental Testing And Modeling Of Automotive Automatic Belt Tensioners, Jiaxin Zhao, Clark R. Barker, Larry Oliver, William Breig, Joey Edson

Mining Engineering Faculty Research & Creative Works

Automatic belt tensioners are used in serpentine belt drive systems in many automotive front end accessory drive (FEAD) applications. The dynamic characteristics of the tensioner must be well defined in order to accurately model the entire belt drive system for system simulation studies. In order to determine required tensioner performance parameters, six different configurations of a production unit were tested over a wide range of frequencies at two different amplitudes of the arm travel. Data was recorded to define the total torque generated by the tensioner as a result of the known input motion to which the arm was subjected. …

Go to article

Constrained Moments Simulation Of Healthcare Capital Acquisitions, A. Narsing, Samuel Frimpong, J. Whiting Jan 1997

Constrained Moments Simulation Of Healthcare Capital Acquisitions, A. Narsing, Samuel Frimpong, J. Whiting

Mining Engineering Faculty Research & Creative Works

Summary form only as given. Two analytical techniques which evaluate capital acquisitions in healthcare are the method of generating system moments and Monte Carlo simulation. Generating system moments enables the user to determine an estimate of the expected cost from a user-supplied function. Furthermore, the user can determine, from a variance component analysis, the sensitivity of the user-supplied function to marginal changes in the random variables by expanding the function about its mean using the Taylor series expansion to the second order. Calculating the magnitude of partial derivatives of each random variable with respect to the user-supplied function indicates the …

Go to article

Method And Apparatus For Applying Herbicides, Marian Mazurkiewicz Jan 1996

Method And Apparatus For Applying Herbicides, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

A method of applying herbicide to plants involves delivering a liquid herbicide solution to the plant foliage in a high pressure jet of sufficient energy to physically disrupt the surface of the foliage. The high pressure jet can be either a coherent jet or it can be a stream of droplets. The coherent stream can have sufficient energy to cut the foliage, creating new surfaces that are more wettable by the herbicide solution, and more susceptible to penetration by the herbicide in the solution. The droplets in the droplet stream can be made to be of sufficient size and energy …

Go to article

Longwall Electrical Control Issues: A Hazardous Waste Containment Application, D. Martinelli, R. S. Nutter Jr., R. Larry Grayson Jan 1994

Longwall Electrical Control Issues: A Hazardous Waste Containment Application, D. Martinelli, R. S. Nutter Jr., R. Larry Grayson

Mining Engineering Faculty Research & Creative Works

No abstract provided.

Go to article

Method Of Stemming A Blast Hole, Paul Nicholas Worsey Oct 1993

Method Of Stemming A Blast Hole, Paul Nicholas Worsey

Mining Engineering Faculty Research & Creative Works

A method of stemming a blast hole loaded with an explosive charge. The blast hole has side walls, an outwardly opening mouth and a central axis extending longitudinally of the blast hole. The method comprises inserting a conduit having a discharge end inwardly through the mouth of the blast hole and positioning the discharge end of the conduit within the blast hole generally adjacent the explosive charge. Particulate stemming material is forced under pressure through the conduit for exit from its discharge end into the blast hole toward the explosive charge thereby to pack stemming material in the blast hole …

Go to article

Blast Plug And Stemming Construction For Blast Holes, Paul Nicholas Worsey Jan 1993

Blast Plug And Stemming Construction For Blast Holes, Paul Nicholas Worsey

Mining Engineering Faculty Research & Creative Works

A plug for use in stemming a blast hole having an explosive charge therein. The plug comprises a wedge member and a stabilizing structure on the wedge member. The wedge member tapers in an outward direction from a relatively wide base to a relatively narrow end and has a central axis extending endwise with respect to the wedge member. The stabilizing structure extends generally axially with respect to the wedge member from adjacent the base of the wedge member. The plug is to be positioned in the blast hole with the base of the wedge member facing inwardly toward the …

Go to article

Dual Purpose Fuze, Paul Nicholas Worsey Jan 1993

Dual Purpose Fuze, Paul Nicholas Worsey

Mining Engineering Faculty Research & Creative Works

A dual purpose fuze for a projectile which can activate a quantity of material selected from a group including high explosive, low explosive, propellant and pyrotechnic compounds. The fuze includes a charge holder having a socket therein facing the quantity of material to be activated. A fuze charge located in the socket has a depression in it so formed as to cause the fuze charge to explode in a jet directed outwardly from the socket of sufficiently high energy to activate a high explosive in a high explosive projectile, the fuze charge being sufficiently small to prevent rupture of containment …

Go to article

High Pressure Lubricooling Machining Of Metals, Marian Mazurkiewicz Jan 1992

High Pressure Lubricooling Machining Of Metals, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

A method of machining metals, by effecting relative movement between a work piece and a tool having a cutting edge to cut the work piece and produce a chip, including injecting a high pressure jet of cooling liquid into the cutting zone during machining, the jet being at a pressure of at least about 5,000 p.s.i. The jet is preferably injected between the chip and the rake face of the cutting tool, and the trajectory of the jet is offset from the rake face of the cutting tool by a small amount and the jet is aimed at the cutting …

Go to article

Disintegration Of Wood, Marian Mazurkiewicz Jan 1991

Disintegration Of Wood, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

Disintegration of a body of organic material involving subjecting the body to liquid jet action with the energy of the liquid as it impacts on the body such as to effect disintegration of the body into particles.

Go to article

A Nuclear Fragmentation Energy Deposition Model, John W. Wilson, D. M. Ngo, T. N. Forgarty, W. W. Buck Jan 1991

A Nuclear Fragmentation Energy Deposition Model, John W. Wilson, D. M. Ngo, T. N. Forgarty, W. W. Buck

Mining Engineering Faculty Research & Creative Works

A formalism for target fragment transport is presented with application to energy loss spectra in thin silicon devices. A nuclear database is recommended that agrees well with the measurements of P.J. McNulty et al. (1980) using surface barrier detectors. High-energy events observed by P.J. McNulty et al. (1981), which are not predicted by intranuclear cascade models, are well represented by this work

Go to article

A Knowledge-Based Expert System For Managing Underground Coal Mines In The U.S., H. Singh, S. Yuan, C. M. Watts, J. M. Dean, N. P. Reddy, R. S. Nutter Jr., R. Larry Grayson Jul 1990

A Knowledge-Based Expert System For Managing Underground Coal Mines In The U.S., H. Singh, S. Yuan, C. M. Watts, J. M. Dean, N. P. Reddy, R. S. Nutter Jr., R. Larry Grayson

Mining Engineering Faculty Research & Creative Works

The Mine Management Support System which is being developed as a knowledge-based expert system for better management of underground coal mines, is presented. Concentrating on capturing the complex body of knowledge needed to enhance efficient management of a mine, it will encompass information and preferred rules on work scheduling, work practices, regulations impinging on the accomplishment of work, responses to operating problems, and the labor-management work agreement. Different components of the mine system, modeled using an object-oriented layering technique, are displayed graphically to aid in coordinating work plans and to present locations of equipment, supplies, and proposed subsystem components.

Go to article

First Prev Next Last